Determination of specific oxygen uptake rate of Photorhabdus luminescens during submerged culture in lab scale bioreactor

Photorhabdus luminescens, a bacterial symbiont of entomoparasitic nematodes, was cultured in a 10 L bioreactor. Cellular density and bioluminescence were recorded and volumetric oxygen transfer coefficient (k_La) and specific oxygen transfer rates were determined during the batch process. Exponential phase of the bacterium lasted for 20 h, showing a maximum specific growth rate of 0.339 h^?1 in a defined medium. Bioluminescence peaked within 21h, and was maintained until the end of the batch process (48 h). The specific oxygen uptake rate (SOUR) was high during both lag and early exponential phase, and eventually reached a stable value of 0.33 mmol g^?1 h^?1 during stationary phase. Maintenance of 200 rpm agitation and 1.4 volume of air per volume of medium per minute (vvm) aeration, gave rise to a k_La value of 39.5 h^?1. This k_La value was sufficient to meet the oxygen demand of 14.4 g L^?1 (DCW) biomass. This research is particularly relevant since there are no reports available on SOURs of symbiotic bacteria or their nematode partners. The insight gained through this study will be useful during the development of a submerged monoxenic culture of Heterorhabditis bacteriophora and its symbiotic bacterium P. luminescens in bioreactors.     

Two-compartment method for determination of the oxygen transfer rate with electrochemical sensors based on sulfite oxidation

The dissolved oxygen concentration is a crucial parameter in aerobic bioprocesses due to the low solubility of oxygen in water. The present study describes a new method for determining the oxygen transfer rate (OTR) in shaken-culture systems based on the sodium sulfite method in combination with an electrochemical oxygen sensor. The method replaces the laborious titration of the remaining sulfite by an on-line detection of the end point of the reaction. This method is a two-step procedure that can be applied in arbitrary flasks that do not allow the insertion of electrodes. The method does not therefore depend on the type of vessel in which the OTR is detected. The concept is demonstrated by determination of the OTR for standard baffled 1-L shake flasks and for opaque Ultra Yield™ flasks. Under typical shaking conditions, k_La values in the standard baffled flasks reached values up to 220 h^-1, whereas the k_La values of the Ultra Yield flasks were significantly higher (up to 422 h^-1).     

A case study in converting disposable process scouting devices into disposable bioreactors as a future bioprocessing tool

In this study, we perform mass transfer characterization (k_La) on a novel mechanically driven/stirred Process Scouting Device, PSD, (SuperSpinner D 1000®, SSD) and demonstrate that this novel device can be viewed as disposable bioreactor. Using patch‐based optical sensors, we were able to monitor critical cell culture environmental conditions such as dissolved oxygen (DO) and pH in SSD for comparison to a 1 L standard spinner (SS) flask. We also coupled these mass transfer studies with mixing time studies where we observed relative high mixing times (5.2 min) that are typically observed in production scale bioreactors. Decreasing the mixing time 3.5‐fold resulted in 30% increase in k_La (from 2.3 to 3.0 h^?1) and minimum DO level increased from 0% to 20% for our model hybridoma cell line. Finally, maximum viable cell density and protein titer stayed within ±20% of historical data, from our standard 5 L stirred bioreactor (Biostat®) operated under active DO control. Biotechnol. Bioeng. 2012; 109: 2790–2797. © 2012 Wiley Periodicals, Inc.     

Syngas fermentation to biofuel: Evaluation of carbon monoxide mass transfer coefficient (kLa) in different reactor configurations

Lignocellulosic biomass such as agri‐residues, agri‐processing by‐products, and energy crops do not compete with food and feed, and is considered to be the ideal renewable feedstocks for biofuel production. Gasification of biomass produces synthesis gas (syngas), a mixture primarily consisting of CO and H₂. The produced syngas can be converted to ethanol by anaerobic microbial catalysts especially acetogenic bacteria such as various clostridia species.One of the major drawbacks associated with syngas fermentation is the mass transfer limitation of these sparingly soluble gases in the aqueous phase. One way of addressing this issue is the improvement in reactor design to achieve a higher volumetric mass transfer coefficient (k_La). In this study, different reactor configurations such as a column diffuser, a 20‐μm bulb diffuser, gas sparger, gas sparger with mechanical mixing, air‐lift reactor combined with a 20‐μm bulb diffuser, air‐lift reactor combined with a single gas entry point, and a submerged composite hollow fiber membrane (CHFM) module were employed to examine the k_La values. The k_La values reported in this study ranged from 0.4 to 91.08 h^?1. The highest k_La of 91.08 h^?1 was obtained in the air‐lift reactor combined with a 20‐μm bulb diffuser, whereas the reactor with the CHFM showed the lowest k_La of 0.4 h^?1. By considering both the k_La value and the statistical significance of each configuration, the air‐lift reactor combined with a 20‐μm bulb diffuser was found to be the ideal reactor configuration for carbon monoxide mass transfer in an aqueous phase. © 2010 American Institute of Chemical Engineers Biotechnol. Prog., 2011     

Xylitol Production from D‐Xylose at Different Oxygen Transfer Coefficients in a Batch Bioreactor

Conversion of D‐xylose to xylitol by Candida boidinii NRRL Y‐17213 was studied under anaerobic and oxygen limited conditions by varying the oxygen transfer coefficient k_La. Shake flask experiments were used to provide the preliminary information required to perform experiments in a bioreactor. The yeast did not grow under fully anaerobic conditions, but anaerobic formations of xylitol, ethanol, ribitol, and glycerol were observed as well as D‐xylose assimilation of 11 %. In shake flasks, with an initial D‐xylose concentration of 50 g/L, an increase in k_La from 8 to 46 h^–1 resulted in a faster growth, higher rate of substrate uptake and lower yields of products. The highest xylitol productivity (0.052 g/L h) was attained at k_La = 8 h^–1. At k_La = 46 h^–1, 98.6 % of D‐xylose was consumed and mainly converted to biomass. Using 130 g/L D‐xylose, k_La was varied in the fermenter from 26 to 78 h^–1. The percentage of consumed D‐xylose increased from 31 % at k_La = 26 h^–1 to 93–94 % at all other aeration levels. Biomass yield increased with k_La, whereas ethanol, ribitol, and glycerol yields exhibited an opposite dependence on the oxygenation level. The most favorable oxygen transfer coefficient for xylitol formation, in the fermenter, was k_La = 47 h^–1 when its concentration (57.5 g/L) surpassed ethanol accumulation by 3.6‐fold, and the glycerol plus ribitol by 10‐fold. Concurrently, xylitol yield and productivity reached 0.45 g/g and 0.26 g/L h, respectively. The volumetric xylitol productivity was affected more by changes in the aeration than the corresponding yield.     

Impact of nozzle operation on mass transfer in jet aerated loop reactors. Characterization and comparison to an aerated stirred tank reactor

The impact of mass transfer on productivity can become a crucial aspect in the fermentative production of bulk chemicals. For highly aerobic bioprocesses the oxygen transfer rate (OTR) and productivity are coupled. The achievable space time yields can often be correlated to the mass transfer performance of the respective bioreactor. The oxygen mass transfer capability of a jet aerated loop reactor is discussed in terms of the volumetric oxygen mass transfer coefficient k_La [h^?1] and the energetic oxygen transfer efficiency E [kgO₂ kW^?1 h^?1]. The jet aerated loop reactor (JLR) is compared to the frequently deployed aerated stirred tank reactor. In jet aerated reactors high local power densities in the mixing zone allow higher mass transfer rates, compared to aerated stirred tank reactors. When both reactors are operated at identical volumetric power input and aeration rates, local k_La values up to 1.5 times higher are possible with the JLR. High dispersion efficiencies in the JLR can be maintained even if the nozzle is supplied with pressurized gas. For increased oxygen demands (above 120 mmol L^?1 h^?1) improved energetic oxygen transfer efficiencies of up to 100 % were found for a JLR compared to an aerated stirred tank reactor operating with Rushton turbines.     

Interactions of cell morphology and transport processes in the lovastatin fermentation

The cholesterol lowering drug, Lovastatin (Mevacor), acts as an inhibitor of HMGCoA reductase, and is produced from an Aspergillus terreus fermentation.Pilot scale studies were carried out in 800 liter fermenters to determine the effects of cell morphology on the oxygen transport properties of this fermentation. Specifically, parallel fermentations giving (i) filamentous mycelial cells, and (ii) discrete mycelial pellets, were quantitatively characterized in terms of broth viscosity, availability of dissolved oxygen, oxygen uptake rates and the oxygen transfer coefficient under identical operating conditions.The growth phase of the fermentation, was operated using a cascade control strategy which automatically changed the agitation speed with the goal of maintaining dissolved oxygen at 50% saturation. Subsequently stepwise changes were made in agitation speed and aeration rate to evaluate the response of the mass transfer parameters (DO, OUR, and k _L a). The results of these experiments indicate considerable potential advantages to the pellet morphology from the standpoint of oxygen transport processes.List of Symbols DO % sat. Dissolved oxygen concentration - k _L a h^–1 Gas-liquid mass transfer coefficient - OUR mmol/dm³h Oxygen uptake rate - P/V KW/m³ Agitator power per unit volume - V _s m/s Superficial air velocity - _app cP Apparent viscosity     

Oxygen transfer in Streptomyces fermentation broths

The oxygen transfer coefficient has been investigated in S. noursci and S. lavendulae fermentation broths obtained from fermentors of different operating volumes (61., 30001., 20,0001.). Fermentors had K_La_s values ranging from 1.0 to 17.0 min^?1, calculated from sulphite oxidation rates. The dynamic measurement of the volumetric oxygen transfer coefficient. (K_La) has been performed in the different fermenting systems. As the fermentation progressed, especially in the first stages, K_La values have decreased in both fermentations and in each system of fermentors. In order to characterise the whole fermenting system an average K_La_s was calculated from the obtained K_La values. The average K_La grew with increasing K_La_s values and ranged from 0.03 to 3.72 min^?l. Some factors possibly having an influence on the, change of K_La have been studied. The oxygen transfer coefficients of the broths have been measured in falling films and ranged from 0.05 to 0.4 cm min^?1. The flow conditions have been characterized by Reynolds numbers of broths varying between 1.0 and 60.0. The average thickness of the falling films have been measured and plotted against Reynolds number. The Re⁺ which is the breaking-point of the plot increased as the fermentation proceeded. In the region of Re⁺ the values of the oxygen transfer coefficient increased rapidly. An approximate correlation could be established between the Re⁺ and the physical properties of fermentation broth.     

Oxygen mass transfer and scale-up studies in baffled roller bioreactors

Oxygen mass transfer was studied in conventional, bead mill and baffled roller bioreactors. Using central composite rotational design, impacts of size, rotation speed and working volume on the oxygen mass transfer were evaluated. Baffled roller bioreactor outperformed its conventional and bead mill counterparts, with the highest k _L a obtained in these configurations being 0.58, 0.19, 0.41 min^?1, respectively. Performances of the bead mill and baffled roller bioreactor were only comparable when a high bead loading (40 %) was applied. Regardless of configuration increase in rotation speed and decrease in working volume improved the oxygen mass transfer rate. Increase in size led to enhanced mass transfer and higher k _L a in baffled roller bioreactor (0.49 min^?1 for 2.2 L and 1.31 min^?1 for 55 L bioreactors). Finally, the experimentally determined k _L a in the baffled roller bioreactors of different sizes fit reasonably well to an empirical correlation describing the k _L a in terms of dimensionless numbers.     

Scale-up and application of a cyclone reactor for fermentation processes

A cyclone reactor for microbial fermentation processes was developed with high oxygen transfer capabilities. Three geometrically similar cyclone reactors with 0.5?l, 2.5?l and 15?l liquid volume, respectively, were characterized with respect to oxygen mass transfer, mixing time and residence time distribution. Semi-empirically correlations for prediction of oxygen mass transfer and mixing times were identified for scale-up of cyclone reactors. A volumetric oxygen mass transfer coefficient k _L a of 1.0?s^?1 (available oxygen transfer rate with air: 29?kg?m^?3?h^?1) was achieved with the cyclone reactor at a volumetric power input of 40?kW?m^?3 and an aeration gas flow rate of 0.2?s^?1. Continuous methanol controlled production of formate dehydrogenase (FDH) with Candida boidinii in a 15?l cyclone reactor resulted in more than 100% improvement in dry cell mass concentration (64.5?g?l^?1) and in about 100% improvement in FDH space-time yield (300?U?l^?1?h^?1) compared to steady state results of a continuous stirred tank reactor.     

Aerobic biodegradation of a mixture of sulfonated azo dyes by a bacterial consortium immobilized in a two‐stage sparged packed‐bed biofilm reactor

The biodegradation of the sulfonated azo dyes, Acid Orange 7 (AO7) and Acid Red 88 (AR88), by a bacterial consortium isolated from water and soil samples obtained from sites receiving discharges from textile industries, was evaluated. For a better removal of azo dyes and their biodegradation byproducts, an aerobically operated two‐stage rectangular packed‐bed biofilm reactor (2S‐RPBR) was constructed. Because the consortium's metabolic activity is affected by oxygen, the effect of the interstitial air flow rate Q_GI on 2S‐RPBR's zonal values of the oxygen mass transfer coefficient k_La was estimated. In the operational conditions probed in the bioreactor, the k_La values varied from 3 to 60 h^?1, which roughly correspond to volumetric oxygen transfer rates, dc_L/dt, ranging from 20 to 375 mg O₂ L^?1h^?1. Complete biodegradation of azo dyes was attained at loading rates B_V,AZ up to 40 mg L^?1d^?1. At higher B_V,AZ values (80 mg L^?1 d^?1), dye decolorization and biodegradation of the intermediaries 4‐amino‐naphthalenesulphonic acid (4‐ANS) and 1‐amino‐2‐naphthol (1‐A2N) was almost complete. However, a diminution in COD and TOC removal efficiencies was observed in correspondence to the 4‐aminobenzenesulfonic acid (4‐ABS) accumulation in the bioreactor. Although the oxygen transport rate improved the azo dye mineralization, the results suggest that the removal efficiency of azo dyes was affected by biofilm detachment at relatively high Q_GI and B_V,AZ values. After 225 days of continuous operation of the 2S‐RFBR, eight bacterial strains were isolated from the biofilm attached to the porous support. The identified genera were: Arthrobacter, Variovorax, Agrococcus, Sphingomonas, Sphingopyxis, Methylobacterium, Mesorhizobium, and Microbacterium.     

Influence of agitation and aeration on growth and antibiotic production by <Emphasis Type="Italic">Xenorhabdus nematophila</Emphasis>

The effect of agitation and aeration on the growth and antibiotic production by Xenorhabdus nematophila YL001 grown in batch cultures were investigated. Efficiency of aeration and agitation was evaluated through the oxygen mass transfer coefficient (K _L a). With increase in K _L a, the biomass and antibiotic activity increased. Activity units of antibiotic and dry cell weight were increased to 232 U ml⁻¹ and 19.58 g l⁻¹, respectively, productivity in cell and antibiotic was up more than 30% when K _L a increased from 115.9 h⁻¹ to 185.7 h⁻¹. During the exponential growth phase, DO concentration was zero, the oxygen supply was not sufficient. So, based on process analysis, a three-stage oxygen supply control strategy was used to improved the DO concentration above 30% by controlling the agitation speed and aeration rate. The dry cell weight and activity units of antibiotic were further increased to 24.22 g l⁻¹ and 249 U ml⁻¹, and were improved by 24.0% and 7.0%, compared with fermentation at a constant agitation speed and a constant aeration rate (300 rev min⁻¹, 2.5 l min⁻¹).     

Characterizing the fluid dynamics in the flow fields of cylindrical orbitally shaken bioreactors with different geometry sizes

Orbitally shaken bioreactors (OSRs) are commonly used for the cultivation of mammalian cells in suspension. To aid the geometry designing and optimizing of OSRs, we conducted a three‐dimensional computational fluid dynamics (CFD) simulation to characterize the flow fields in a 10 L cylindrical OSR with different vessel diameters. The liquid wave shape captured by a camera experimentally validated the CFD models established for the cylindrical OSR. The geometry size effect on volumetric mass transfer coefficient (k_La) and hydromechanical stress was analyzed by varying the ratio of vessel diameter (d) to liquid height at static (h_L), d/h_L. The highest value of k_La about 30 h^?1 was observed in the cylindrical vessel with the d/h_L of 6.35. Moreover, the magnitudes of shear stress and energy dissipation rate in all the vessels tested were below their minimum values causing cells damage separately, which indicated that the hydromechanical‐stress environment in OSRs is suitable for cells cultivation in suspension. Finally, the CFD results suggested that the d/h_L higher than 8.80 should not be adopted for the 10 L cylindrical OSR at the shaking speed of 180 rpm because the “out of phase” state probably will happen there.     

A new dynamic model for highly efficient mass transfer in aerated bioreactors and consequences for kLa identification

Gas–liquid mass transfer is often rate‐limiting in laboratory and industrial cultures of aerobic or autotrophic organisms. The volumetric mass transfer coefficient k_La is a crucial characteristic for comparing, optimizing, and upscaling mass transfer efficiency of bioreactors. Reliable dynamic models and resulting methods for parameter identification are needed for quantitative modeling of microbial growth dynamics. We describe a laboratory‐scale stirred tank reactor (STR) with a highly efficient aeration system (k_La ≈ 570 h^?1). The reactor can sustain yeast culture with high cell density and high oxygen uptake rate, leading to a significant drop in gas concentration from inflow to outflow (by 21%). Standard models fail to predict the observed mass transfer dynamics and to identify k_La correctly. In order to capture the concentration gradient in the gas phase, we refine a standard ordinary differential equation (ODE) model and obtain a system of partial integro‐differential equations (PIDE), for which we derive an approximate analytical solution. Specific reactor configurations, in particular a relatively short bubble residence time, allow a quasi steady‐state approximation of the PIDE system by a simpler ODE model which still accounts for the concentration gradient. Moreover, we perform an appropriate scaling of all variables and parameters. In particular, we introduce the dimensionless overall efficiency κ, which is more informative than k_La since it combines the effects of gas inflow, exchange, and solution. Current standard models of mass transfer in laboratory‐scale aerated STRs neglect the gradient in the gas concentration, which arises from highly efficient bubbling systems and high cellular exchange rates. The resulting error in the identification of κ (and hence k_La) increases dramatically with increasing mass transfer efficiency. Notably, the error differs between cell‐free and culture‐based methods of parameter identification, potentially confounding the determination of the “biological enhancement” of mass transfer. Our new model provides an improved theoretical framework that can be readily applied to aerated bioreactors in research and biotechnology. Biotechnol. Bioeng. 2012; 109: 2997–3006. © 2012 Wiley Periodicals, Inc.     

Study of the oxygen transfer in a disposable flexible bioreactor with surface aeration in vibrated medium

The oxygen mass transfer is a critical design parameter for most bioreactors. It can be described and analyzed by means of the volumetric mass transfer coefficient K _L a. This coefficient is affected by many factors such as geometrical and operational characteristics of the vessels, type, media composition, rheology and microorganism’s morphology and concentration. In this study, we aim to develop and characterize a new culture system based on the surface aeration of a flexible, single-used bioreactor fixed on a vibrating table. In this context, the K _L a was evaluated using a large domain of operating variables such as vibration frequency of the table, overpressure inside the pouch and viscosity of the liquid. A novel method for K _L a determination based on the equilibrium state between oxygen uptake rate and oxygen transfer rate of the system at given conditions was also developed using resting cells of baker’s fresh yeast with a measured oxygen uptake rate of 21 mg g⁻¹ h⁻¹ (at 30°C). The effect of the vibration frequency on the oxygen transfer performance was studied for frequencies ranging from 15 to 30 Hz, and a maximal K _L a of 80 h⁻¹ was recorded at 30 Hz. A rheological study of the medium added with carboxymethylcellulose at different concentrations and the effect of the liquid viscosity on K _L a were determined. Finally, the mixing time of the system was also measured using the pH method.     

Studies on mass transfer characteristics of a modified airlift fermenter

An approach to modify external loop airlift bioreactor is presented that examines its performance with respect to mass transfer. There are various designs of airlift fermenter [1]. In the proposed system [2] the riser has been replaced by a tube of irregular geometry, in the form of converging-diverging sections (CDT-ALF), so that better mass transfer may be obtained due to better liquid mixing caused by the bubble flow, pulsation effect and early transition to turbulence. Mass transfer characteristics of the modified airlift fermenter CDT-ALF were studied and compared with those of a conventional one, UT-ALF. Overall volumetric mass transfer coefficient,K _L a, was determined by sulfite oxidation method.K _L a was determined with respect toU _G for differenth _i. HigherK _L a was always observed in CDT-ALF compared to that in UT-ALF under any operating condition ofh _i andU _G. If theK _L a values are compared in both the systems under their optimum conditions ofh _i andU _G, CDT-ALF showed 122.5% higher values ofK _L a compared to UT-ALF. However, when both the systems were operated at the lowest experimental conditions ofU _G, thek _L a in CDT-ALF was found to be 170% higher. In UT-ALF while with the decrease ofU _G,k _L a decreased, in CDT-ALF the reverse was observed i.e. at lowU _G,K _L a was higher. However with the increase ofh _i,K _L a decreased in both the systems. To predict volumetric mass transfer coefficientK _L a, empirical correlations were developed by dimensional analysis for both the reactors. The correlations were experimentally verified to determine their reliability to predict mass transfer coefficient and the deviation was found within reasonable limit.List of abbreviations ALF Airlift Fermenter - UT-ALF Uniform Tube Airlift Fermenter - CDT-ALF Converging-diverging Tube Airlift Fermenter     

Enhancement of anthocyanin production by Perilla frutescens cells in a stirred bioreactor with internal light irradiation

Oxygen supply and light irradiation exhibited significant influence on the production of anthocyanin (red pigments) by suspended cultures of Perilla frutescens cells in a 2.6-l aerated and agitated bioreactor with a six-flat-bladed turbine. When the initial volumetric oxygen transfer coefficient (k_La) value was below 10 h⁻¹ and light was not irradiated, the anthocyanin production was never over 0.6 g/l. By modification of a gas sparger, the oxygen supply capability of the bioreactor was remarkably improved, and 1.65 g/l of anthocyanin was obtained at an enhanced k_La value of 15.4 h⁻¹. Moreover, it was found that anthocyanin accumulation at a 0.2 vvm aeration rate was higher than that at 0.1 or 0.4 vvm in the modified bioreactor, with the other cultivation conditions kept the same. Light irradiation also significantly increased anthocyanin accumulation in the stirred reactor at a low k_La value, i.e. 9.9 h⁻¹. However, a combination of irradiation with a higher oxygen supply reduced the production of anthocyanin in the bioreactor.     

Corynebacterium glutamicum,a natural overproducer of succinic acid?

Corynebacterium glutamicum is well known as an important industrial amino acid producer. For a few years, its ability to produce organic acids, under micro‐aerobic or anaerobic conditions was demonstrated. This study is focused on the identification of the culture parameters influencing the organic acids production and, in particular, the succinate production, by this bacterium. Corynebacterium glutamicum 2262, used throughout this study, was a wild‐type strain, which was not genetically designed for the production of succinate. The oxygenation level and the residual glucose concentration appeared as two critical parameters for the organic acids production. The maximal succinate concentration (4.9 g L^?1) corresponded to the lower k_La value of 5 h^?1. Above 5 h^?1, a transient accumulation of the succinate was observed. Interestingly, the stop in the succinate production was concomitant with a lower threshold glucose concentration of 9 g L^?1. Taking into account this threshold, a fed‐batch culture was performed to optimize the succinate production with C. glutamicum 2262. The results showed that this wild‐type strain was able to produce 93.6 g L^?1 of succinate, which is one of the highest concentration reported in the literature.     

On-line estimation of kLa by an analog computer

A new method was developed for estimating the volumetric oxygen transfer coefficient, k_La, in a fermentor. Various methods were investigated for the on-line estimation of k_La with an analog computer employing a steepest-descent calculation technique. The method by which k_La is estimated (by minimizing the error residue of the model) was found to be very applicable. A method for the simultaneous estimation of the volumetric oxygen transfer coefficient and respiration rate in biological systems is also presented.     

Mixing and oxygen transfer characteristics of a microplate bioreactor with surface-attached microposts

Bioprocess optimization for cell-based therapies is a resource heavy activity. To reduce the associated cost and time, process development may be carried out in small volume systems, with the caveat that such systems be predictive for process scale-up. The transport of oxygen from the gas phase into the culture medium, characterized using the volumetric mass transfer coefficient, k_La, has been identified as a critical parameter for predictive process scale-up. Here, we describe the development of a 96-well microplate with integrated Redbud Posts to provide mixing and enhanced k_La. Mixing in the microplate is characterized by observation of dyes and analyzed using the relative mixing index (RMI). The k_La is measured via dynamic gassing out method. Actuating Redbud Posts are shown to increase rate of planar homogeneity (2 min) verse diffusion alone (120 min) and increase oxygenation, with increasing stirrer speed (3500-9000 rpm) and decreasing fill volume (150-350 μL) leading to an increase in k_La (4-88 h⁻¹). Significant increase in Chinese Hamster Ovary growth in Redbud Labs vessel (580,000 cells mL^-1) versus the control (420,000 cells mL^-1); t(12.814) = 8.3678, p ≤ .001), and CD4⁺ Naïve cell growth in the microbioreactor indicates the potential for this technology in early stage bioprocess development and optimization.