营养补偿和代谢控制提高连续灌注培养重组肿瘤坏死因子受体p75:Fc的蛋白产率

为解决连续灌注培养产物因营养物质不能有效利用而导致产率偏低的问题,降低生产成本,我们通过在发酵过程中测定表达重组肿瘤坏死因子受体p75:Fc（TNFRp75:Fc）蛋白的CHO工程细胞株对氨基酸成分的不同消耗速率,定量添加特定氨基酸作为营养补偿,提高了培养基中氨基酸的综合利用效率;同时,在连续灌注过程中通过对葡萄糖补加的限量控制,使培养体系中葡萄糖始终低于0.5 g/L,减少了乳酸蓄积对细胞的毒性作用,从而有效降低了灌注速率。结果显示,在30L工作体积发酵规模上经过氨基酸补偿和葡萄糖控制的连续灌注培养工艺使最终重组蛋白产率（mg/L）和最终产量较工艺改进前提高了2.1倍和3.7倍,分别达到388mg/L和244.4g,生产周期延长了一周。工艺改进前后重组蛋白的唾液酸含量和体外生物比活没有改变。通过营养补偿和代谢控制工艺策略可以有效提高连续灌注培养工艺重组肿瘤坏死因子受体p75:Fc蛋白的产率和产能,从而降低产业化成本。     

Perfusion culture of hybridoma cells for hyperproduction of IgG(2a) monoclonal antibody in a wave bioreactor-perfusion culture system

A novel wave bioreactor-perfusion culture system was developed for highly efficient production of monoclonal antibody IgG2a (mAb) by hybridoma cells. The system consists of a wave bioreactor, a floating membrane cell-retention filter, and a weight-based perfusion controller. A polyethylene membrane filter with a pore size of 7 microm was floating on the surface of the culture broth for cell retention, eliminating the need for traditional pump around flow loops and external cell separators. A weight-based perfusion controller was designed to balance the medium renewal rate and the harvest rate during perfusion culture. BD Cell mAb Medium (BD Biosciences, CA) was identified to be the optimal basal medium for mAb production during batch culture. A control strategy for perfusion rate (volume of fresh medium/working volume of reactor/day, vvd) was identified as a key factor affecting cell growth and mAb accumulation during perfusion culture, and the optimal control strategy was increasing perfusion rate by 0.15 vvd per day. Average specific mAb production rate was linearly corrected with increasing perfusion rate within the range of investigation. The maximum viable cell density reached 22.3 x 105 and 200.5 x 105 cells/mL in the batch and perfusion culture, respectively, while the corresponding maximum mAb concentration reached 182.4 and 463.6 mg/L and the corresponding maximum total mAb amount was 182.4 and 1406.5 mg, respectively. Not only the yield of viable cell per liter of medium (32.9 x 105 cells/mL per liter medium) and the mAb yield per liter of medium (230.6 mg/L medium) but also the mAb volumetric productivity (33.1 mg/L.day) in perfusion culture were much higher than those (i.e., 22.3 x 105 cells/mL per liter medium, 182.4 mg/L medium, and 20.3 mg/L.day) in batch culture. Relatively fast cell growth and the perfusion culture approach warrant that high biomass and mAb productivity may be obtained in such a novel perfusion culture system (1 L working volume), which offers an alternative approach for producing gram quantity of proteins from industrial cell lines in a liter-size cell culture. The fundamental information obtained in this study may be useful for perfusion culture of hybridoma cells on a large scale.     

Fermentor temperature as a tool for control of high-density perfusion cultures of mammalian cells

Temperature is a key environmental variable whose potential in animal cell fermentor optimization is not yet fully utilized. The scarce literature data suggests that reduced fermentor temperature results in an improved viability and shear resistance, higher cell density and titer in batch cultures, and reduction in glucose/lactate metabolism. Due to the arrest of the cells in the G1 phase, the specific growth rate was found to decrease at temperatures below 37.0 degrees C. The response of the specific production rate was cell line dependent: in some cases it increased 2-to-3-fold, but decreased in other cases. The controlable slowdown of cell metabolism at lower temperature can be used in optimization of perfusion mammalian cell cultures with several potential advantages, including higher cell density in oxygen limited reactors, lower perfusion rate, improved product quality, simplified pH control, and others. To evaluate this strategy, a series of long-term experiments in 15 L perfusion bioreactors culturing recombinant hamster cells at 20.0 x 10(6) cells/mL were conducted. The temperature was changed over a range of set points, and maintained at each of these for a long period of time. Steady state process data was collected and analyzed. The effect of temperature on the following characteristics of the perfusion process was studied: cell growth, glucose/lactate metabolism, glutamine/ammonia metabolism, cell respiration, cell density at constant oxygen transfer rate, proteolytic activity, and product quality (glycosylation and molecule fragmentation). The results suggest that temperature is a variable with a significant potential in optimization of perfusion cultures. Properly selected temperature set point will contribute to the overall improvement of process performance. (c) 1997 John Wiley & Sons, Inc. Biotechnol Bioeng 55: 328-338, 1997.     

杂交瘤细胞培养中摄氧速率(OUR)的在线检测及其与细胞生长及代谢的关系

在批式及灌流培养条件下研究了杂交瘤细胞在无血清培养基中的生长、代谢情况与氧消耗的关系。应用动力学方法在线进行OUR的检测,同时离线取样检测其他参数。结果发现OUR与谷氨酰胺的消耗、抗体的生成及活细胞密度间有明显的相关关系,进一步的分析还发现在对数生长期,OUR与活细胞密度间具有良好的线性关系,qOUR(0.103±0.028)×10^-12mol/cell/h,可以通过它来进行细胞密度的在线检测。并通过以ΔOUR=0时刻作为灌流调整点进行连续灌流培养的初步实验验证了OUR作为培养过程反馈控制参数的可能性。     

Characterization and optimization of acoustic filter performance by experimental design methodology

Acoustic cell filters operate at high separation efficiencies with minimal fouling and have provided a practical alternative for up to 200 L/d perfusion cultures. However, the operation of cell retention systems depends on several settings that should be adjusted depending on the cell concentration and perfusion rate. The impact of operating variables on the separation efficiency performance of a 10-L acoustic separator was characterized using a factorial design of experiments. For the recirculation mode of separator operation, bioreactor cell concentration, perfusion rate, power input, stop time and recirculation ratio were studied using a fractional factorial 2(5-1) design, augmented with axial and center point runs. One complete replicate of the experiment was carried out, consisting of 32 more runs, at 8 runs per day. Separation efficiency was the primary response and it was fitted by a second-order model using restricted maximum likelihood estimation. By backward elimination, the model equation for both experiments was reduced to 14 significant terms. The response surface model for the separation efficiency was tested using additional independent data to check the accuracy of its predictions, to explore robust operation ranges and to optimize separator performance. A recirculation ratio of 1.5 and a stop time of 2 s improved the separator performance over a wide range of separator operation. At power input of 5 W the broad range of robust high SE performance (95% or higher) was raised to over 8 L/d. The reproducible model testing results over a total period of 3 months illustrate both the stable separator performance and the applicability of the model developed to long-term perfusion cultures.     

Production of ethanol by Clostridium thermosaccharolyticum: I. Effect of cell recycle and environmental parameters

The direct microbial conversion (DMC) process for the production of ethanol from lignocellulosic biomass is limited by low volumetric ethanol production rates due to the low cell densities of Clostridium thermosaccharolyticum which is a key organism for ethanol production in this process. Hence, this study focuses on the use of a continuous- culture cell recycle system to improve the volumetric ethanol productivity and yield of the fermentation of xylose by C. thermosaccharolyticum. Early experiments with the continuous-culture cell recycle system showed a two-fold improvement in volumetric ethanol productivity. However, the ethanol yield at the higher dilution rates suffered because of the large amount of lactate produced. The manipulation of two environmental parameters-iron concentration in the nutrient medium and the N(2) purge rate of the fermentor headspace-allowed a dramatic reduction in the lactate production and a simultaneous improvement in the ethanol titer and yield. Under the improved conditions of increased iron concentration (12.5 mg/L FeSO(4) . 7H(2)O) and decreased N(2) purge rate (0.1 L/min), a continuous culture of C. thermosaccharolyticum operating at a dilution rate of 0.24 h(-1) and 50% cell recycle produced 8.6 g/L ethanol and less than 1 g/L each of acetate and lactate. The volumetric ethanol productivity was 2.2 g/L/h, which is 8 times larger than obtained for a continuous culture operated with no cell recycle and the same specific growth rate.     

Insights into adenoviral vector production kinetics in acoustic filter-based perfusion cultures

One of the major limitations in the production of adenoviral vectors is the reduction in cell-specific productivity observed for increasing cell density at infection in batch cultures. This observation strongly suggests some nutrient depletion and/or metabolite inhibition in the media. These limitations have been partially overcome through other feeding strategies, such as fed-batch and sequential batch operations. To improve these results, we evaluated perfusion as a strategy to increase the volumetric productivity of HEK-293 cell cultures, by allowing productive infection at higher cell densities. An acoustic cell separator was employed in consideration of the increased shear sensitivity of the cells during the infection phase. The effects of perfusion rate and cell density at infection on the production of a recombinant adenovirus expressing the GFP were investigated. The perfusion mode allowed successful infection at cell densities in the range of 2.4-3 x 10(6) cell/mL, while maintaining a similar cell specific productivity (17,900 +/- 2400 VP/cell) to that of a batch infected at a low cell density (5 x 10(5) cell/mL). The highest virus concentrations (4.1 +/- 0.6 x 10(10) VP/mL) were attained for a feed rate of 2 vol/d and constituted a fivefold increase compared to a batch with medium replacement. Rapid assessment of the infection status was achieved through the use of on-line monitoring of respiration, fluorescence, and biovolume. Analysis of the kinetics of nutrient consumption and metabolite production revealed that a reduction in specific productivity is correlated with reduced metabolic activity.     

Alteration of mammalian cell metabolism by dynamic nutrient feeding

The metabolism of hybridoma cells was controlled to reduce metabolic formation in fed-batch cultures by dynamically feeding a salt-free nutrient concentrate. For this purpose, on-line oxygen uptake rate (OUR) measurement was used to estimate the metabolic demand of hybridoma cells and to determine the feeding rate of a concentrated solution of salt-free DMEM/F12 medium supplemented with other medium components. The ratios among glucose, glutamine and other medium components in the feeding nutrient concentrate were adjusted stoichiometrically to provide balanced nutrient conditions for cell growth. Through on-line control of the feeding rate of the nutrient concentrate, both glucose and glutamine concentrations were maintained at low levels of 0.5 and 0.2 mM respectively during the growth stage. The concentrations of the other essential amino acids were also maintained without large fluctuations. The cell metabolism was altered from that observed in batch cultures resulting in a significant reduction of lactate, ammonia and alanine production. Compared to a previously reported fed-batch culture in which only glucose was maintained at a low level and only a reduced lactate production was observed, this culture has also reduced the production of other metabolites, such as ammonium and alanine. As a result, a high viable cell concentration of more than 1.0 × 10⁷ cells/mL was achieved and sustained over an extended period. The results demonstrate an efficient nutrient feeding strategy for controlling cell metabolism to achieve and sustain a high viable cell concentration in fed-batch mammalian cell cultures in order to enhance the productivity. This revised version was published online in July 2006 with corrections to the Cover Date.     

Production of a self-activating CBM-factor X fusion protein in a stable transformed Sf9 insect cell line using high cell density perfusion culture

Factor Xa is a serine protease, whose high selectivity can be used to cleave protein tags from recombinant proteins. A fusion protein comprised of a self-activating form of factor X linked to a cellulose-binding module, saCBMFX, was produced in a stable transformed Sf9 insect cell line. The activity of the insect cell produced saCBMFX was higher than the equivalent mammalian cell produced material. A 1.5 l batch fermentation reached a maximum cell concentration of 1.6 × 10⁷ cells ml⁻¹ and a final saCBMFX concentration of 4 mg l⁻¹. The production of saCBMFX by this cell line was also analyzed in a 1.5 l perfusion system using an ultrasonic filter as a cell-retention device for flow rates up to 3.5 l day⁻¹. The cell-retention efficiency of an air backflush mode of acoustic filter operation was greater than 95% and eliminated the need to pump the relatively shear sensitive insect cells. In the perfusion system over 4 × 10⁷ Sf9 cells ml⁻¹ were obtained with a viability greater than 80%. With a doubling of viable cell concentration from 1.5 to 3 × 10⁷ cells ml⁻¹ the saCBMFX production rate was doubled to 6 mg l⁻¹ day⁻¹. The saCBMFX volumetric productivity of the perfusion system was higher than the batch fermentations (0.6 mg l⁻¹ day⁻¹) by an order of magnitude.     

Dynamics of recombinant protein production by mammalian cells in immobilized perfusion culture

In spite of the generally stable nature of immobilized perfusion culture, its profile of target protein production frequently shows variations. This might be explained by the drift in the metabolism of cultured cells. To address this issue, we performed a set of four Opticell bioreactor cultures producing recombinant anticogulant protein PCGFX. All the cultures lasted 40-50 days with the oxygen consumption rate (OCR) mostly around 10 μmol min⁻¹; nevertheless, glucose and lactate metabolism was fluctuated with a parallel fluctuation in the recombinant protein productivity (RPP). The mean productivity of recombinant PCGFX was determined to be about 1.0 mg day⁻¹ for all the cultures. The statistical analysis revealed a significant correlation between the lactate production rate (LPR) and RPP in two cultures. A significant correlation was further found between average OCR and RPP in another culture where OCR was exceptionally lowered under serum-free conditions. No parameter significantly correlated with RPP in the remaining one culture; thus, the overt drift of RPP resulted, at least partly, from that of the cell metabolic activity and the present data should be helpful to explore a strategy for maximizing productivity.     

Fed-batch culture of recombinant NS0 myeloma cells with high monoclonal antibody production

An amplified NS0 cell line transfected with a vector expressing a humanized monoclonal antibody (MAb) against CD-18 and glutamine synthetase (GS) was cultivated in a 1.5 L fed-batch culture using a serum-free, glutamine-free medium. Concentrated solutions of key nutrient components were fed periodically using a simple feeding control strategy. Feeding amounts were adjusted daily based on the integral of viable cell concentration over time (IVC) and assumed constant specific nutrient consumption rates or yields to maintain concentrations of the key nutrient components around their initial levels. On-line oxygen uptake rate (OUR) measurement was used to aid empirically the adjustment of the feeding time points and amounts by inferring time points of nutrient depletion. Through effective nutritional control, both cell growth phase and culture lifetime were prolonged significantly, resulting in a maximal viable cell concentration of 6.6 x 10(9) cells/L and a final IVC of 1.6 x 10(12) cells-h/L at 672 h. The final MAb concentration reached more than 2.7 g/L. In this fed-batch culture, cellular metabolism shifts were repeatedly observed. Accompanying the culture phase transition from the exponential growth to the stationary phase, lactate, which was produced in the exponential growth phase, became consumed. The time point at which this metabolism shift occurred corresponded to that of rapid decrease of OUR, which most likely was caused by nutrient depletion. This transition coincided with the onset of ammonia, glutamate and glutamine accumulation. With removal of the nutrient depletion by increasing the daily nutrient feeding amount, OUR recovered and viable cell concentration increased, while cell metabolism shifted again. Instead of consumption, lactate became produced again. These results suggest close relationships among nutrient depletion, cell metabolism transition, and cell death. (c) 1997 John Wiley & Sons, Inc. Biotechnol Bioeng 55: 783-792, 1997.     

Optimization of an acoustic cell filter with a novel air-backflush system

Increasing worldwide demand for mammalian cell production capacity will likely be partially satisfied by a greater use of higher volumetric productivity perfusion processes. An important additional component of any perfusion system is the cell retention device that can be based on filtration, sedimentation, and/or acoustic technologies. A common concern with these systems is that pumping and transient exposure to suboptimal medium conditions may damage the cells or influence the product quality. A novel air-backflush mode of operating an acoustic cell separator was developed in which an injection of bioreactor air downstream of the separator periodically returned the captured cells to the reactor, allowing separation to resume within 20 s. This mode of operation eliminated the need to pump the cells and allows the selection of a residence time in the separator depending on the sensitivity of the cell line. The air-backflush mode of operating a 10L acoustic separator was systematically tested at 10(7) cells/mL to define reliable ranges of operation. Consistent separation performance was obtained for wide ranges of cooling airflow rates from 0 to 15 L/min and for backflush frequencies between 10 and 40 h(-1). The separator performance was optimized at a perfusion rate of 10 L/day to obtain a maximum separation efficiency of 92 +/- 0.3%. This was achieved by increasing the power setting to 8 W and using duty cycle stop and run times of 4.5 and 45 s, respectively. Acoustic cell separation with air backflush was successfully applied over a 110 day CHO cell perfusion culture at 10(7) cells/mL and 95% viability.     

Very high density of Chinese hamster ovary cells in perfusion by alternating tangential flow or tangential flow filtration in WAVE bioreactor™—part II: Applications for antibody production and cryopreservation

A high cell density perfusion process of monoclonal antibody (MAb) producing Chinese hamster ovary (CHO) cells was developed in disposable WAVE Bioreactor? using external hollow fiber (HF) filter as cell separation device. Tangential flow filtration (TFF) and alternating tangential flow (ATF) systems were compared and process applications of high cell density perfusion were studied here: MAb production and cryopreservation. Operations by perfusion using microfiltration (MF) or ultrafiltration (UF) with ATF or TFF and by fed‐batch were compared. Cell densities higher than 10⁸ cells/mL were obtained using UF TFF or UF ATF. The cells produced comparable amounts of MAb in perfusion by ATF or TFF, MF or UF. MAbs were partially retained by the MF using ATF or TFF but more severely using TFF. Consequently, MAbs were lost when cell broth was discarded from the bioreactor in the daily bleeds. The MAb cell‐specific productivity was comparable at cell densities up to 1.3 × 10⁸ cells/mL in perfusion and was comparable or lower in fed‐batch. After 12 days, six times more MAbs were harvested using perfusion by ATF or TFF with MF or UF, compared to fed‐batch and 28× more in a 1‐month perfusion at 10⁸ cells/mL density. Pumping at a recirculation rate up to 2.75 L/min did not damage the cells with the present TFF settings with HF short circuited. Cell cryopreservation at 0.5 × 10⁸ and 10⁸ cells/mL was performed using cells from a perfusion run at 10⁸ cells/mL density. Cell resuscitation was very successful, showing that this system was a reliable process for cell bank manufacturing. © 2013 American Institute of Chemical Engineers Biotechnol. Prog., 29:768–777, 2013     

Scale-up and optimization of an acoustic filter for 200 L/day perfusion of a CHO cell culture

Acoustic cell retention devices have provided a practical alternative for up to 50 L/day perfusion cultures but further scale-up has been limited. A novel temperature-controlled and larger-scale acoustic separator was evaluated at up to 400 L/day for a 10(7) CHO cell/mL perfusion culture using a 100-L bioreactor that produced up to 34 g/day recombinant protein. The increased active volume of this scaled-up separator was divided into four parallel compartments for improved fluid dynamics. Operational settings of the acoustic separator were optimized and the limits of robust operations explored. The performance was not influenced over wide ranges of duty cycle stop and run times. The maximum performance of 96% separation efficiency at 200 L/day was obtained by setting the separator temperature to 35.1 degrees C, the recirculation rate to three times the harvest rate, and the power to 90 W. While there was no detectable effect on culture viability, viable cells were selectively retained, especially at 50 L/day, where there was a 5-fold higher nonviable washout efficiency. Overall, the new temperature-controlled and scaled-up separator design performed reliably in a way similar to smaller-scale acoustic separators. These results provide strong support for the feasibility of much greater scale-up of acoustic separations.     

Optical analysis of perfusion bioreactor cell concentration in an acoustic separator

Automated monitoring of cell concentration in perfusion bioprocesses facilitates the maintenance of constant cell specific perfusion rates. However, most on-line measuring devices are relatively complex and foul as the culture progresses. A simple external optical sensor was developed using the transparent glass walls of acoustic separators for automated optical analysis of their contents. For each measurement, the separator was filled by an automated pumping system with triplicate representative bioreactor samples that were optically analyzed and the device returned to perfusion operation within approximately 1 or 2 min. Chinese hamster ovary cell concentrations, ranging from 5 x 10(5) to 2 x 10(7) cells/mL, were highly correlated (R(2) = 0.99) with the 90 degrees scattered light response. Since the device was operated externally, it did not complicate bioreactor sterilization or cleaning. Viability was not optically analyzed, but this information was not required between manual samples of a properly operated perfusion process. Using single-point recalibration based on routine off-line samples, this external optical system remained effective during a 4-month perfusion run, thus providing a non-invasive and easily maintained on-line cell concentration monitoring system to improve the control of perfusion bioreactors.     

Enhanced mixing and mass transfer in a recirculation loop results in high cell densities in a roller bottle reactor

A recirculation loop added to a large-scale roller bottle reactor resulted in high cell densities as compared to standard roller bottles. Four different mammalian cell lines reached an average maximum density equal to 5.4 x 10(6) cells /mL (sigma = 0.263), which was between 2.13 and 2.95 times greater than the densities in roller bottles without recirculation using the same cell lines. The high densities were maintained over long durations (>25 days) while the reactor operated with continuous perfusion. The increased densities are attributed to enhanced liquid mixing and oxygen transfer that occur as a result of the recirculation loop. Models were developed that describe axial liquid flow and oxygen transfer in both the sample loop and the reactor growth chamber. Axial dispersion and oxygen transfer coefficients are presented for a variety of operating conditions. The increased oxygen transfer characteristics of the reactor allow for easy scale-up of roller bottle cultures by operating at larger volumes with greater liquid depths than conventional roller bottles permit. The surface-area-to-volume ratio in the tests performed was 0.206 versus 1.16 cm(-1) in a standard roller bottle.     

Transient responses of hybridoma metabolism to changes in the oxygen supply rate in continuous culture

Oxygen is an important nutrient that may limit the productivity of commercial cell culture reactors. The transient responses of hybridoma growth and metabolism to step changes in the oxygen supply rate have been examined for dissolved oxygen concentrations (DO) ranging from 0.1% to 10% of air saturation in continuous culture. Metabolic quotients are reported for glucose, lactate, ammonia, oxygen, glutamine, alanine and other amino acids. A majority of the estimated ATP production was due to oxidative phosphorylation under all conditions tested. Decreases in the oxygen supply rate below the value required to maintain 0.5% DO caused the viable cell concentration to decrease. Glycolysis was enhanced at the lower oxygen concentrations, and after an initial decrease, the specific glutamine consumption rate was also higher. High residual glutamine concentrations occurred below 0.5% DO. Oxidation of other amino acids and production of serine were also inhibited. The cells subsequently adapted to low oxygen concentrations. The increase in cell concentration following the return to 10% DO was preceded by increased biosynthetic activity, as evidenced by transiently reduced yields of lactate from glucose, and alanine and ammonia from glutamine.     

Selective recycle of viable animal cells by coupling of airlift reactor and cell settler

A new system for the perfusion culture of animal cells in suspension is described. It consists of an airlift loop reactor and a settling tank for cell retention. Insufficient nutrient and oxygen supply of the cells in the settling tank was prevented by cooling the cell suspension before entering the settler. As a result, the catabolic activity of the cells in the settler was reversibly reduced. Furthermore, the density gradient induced by cooling caused a liquid motion through the settler. Thus, it was not necessary to pump medium containing shear, sensitive cells. With this simple system, it was possible to prduce 2 to 5 g of antibodies in a 5.4-L reactor in continuous runs of 400 to 600 h. The productivity was increased by a factor of 17 and the cell density was 4 times higher in comparison with the corresponding batch system. The cell retention system was found to have the property of separating viable and nonviable cells. With the increasing perfusion rate, dead cells and debris were preferably washed out. For perfusion rates up to 1.3 d(-1), the retention efficiency of the settler was nearly 100% for viable cells; hence, this system may show advantages at the industrial scale.     

Continuous stable production of von Willebrand Factor monoclonal antibody in spin filter bioreactor with bleeding technology

The characteristics of two different modes of perfusion culture, intermittent and continuous bleedings, were investigated by culturing the hybridoma cells producing von Willebrand Factor (vWF) monoclonal antibody (McAb) in a 15 L bioreactor without clogging the filter. Both culture methods exhibited similar profiles of cell density and metabolite concentrations during the culture period at the cell concentration of around 1×10⁷ cells/mL. When the perfusion rate was increased, the intermittent bleeding culture showed problems of ammonia accumulation and decrease of cell viability. The continuous bleeding culture exhibited higher physiological activity than that of the intermittent bleeding culture in terms of nutrient consumption and metabolite production kinetics. But the analysis of specific oxygen consumption rate showed that the specific oxygen consumption rate of intermittent bleeding culture was similar to that of exponential growth phase. The continuous bleeding culture showed higher specific vWF McAb productivity and cumulative production than those of the intermittent bleeding culture. Finally we proved the possibility of long-term operation of continuous bleeding culture and produced approximately 40 g of vWF McAb in a 15 L bioreactor after one-month operation.     

On-line characterization of a hybridoma cell culture process

The on-line determination of the physiological state of a cell culture process requires reliable on-line measurements of various parameters and calculations of specific rates from these measurements. The cell concentration of a hybridoma culture was estimated on-line by measuring optical density (OD) with a laser turbidity probe. The oxygen uptake rate (OUR) was determined by monitoring dynamically dissolved oxygen concentration profiles and closing oxygen balances in the culture. The base addition for neutralizing lactate produced by cells was also monitored on-line via a balance. Using OD and OUR measurements, the specific growth and specific oxygen consumption rates were determined on-line. By combining predetermined stoichiometric relationships among oxygen and glucose consumption and lactate production, the specific glucose consumption and lactate production rates were also calculated on-line. Using these on-line measurements and calculations, the hybridoma culture process was characterized on-line by identifying the physiological states. They will also facilitate the implementation of nutrient feeding strategies for fed-batch and perfusion cultures. (c) 1994 John Wiley & Sons, Inc.