The relative importance of genetics and phenotypic plasticity in dictating bone morphology and mechanics in aged mice: evidence from an artificial selection experiment

Both genetic and environmental factors are known to influence the structure of bone, contributing to its mechanical behavior during, and adaptive response to, loading. We introduce a novel approach to simultaneously address the genetically mediated, exercise-related effects on bone morphometrics and strength, using mice that had been selectively bred for high levels of voluntary wheel running (16 generations). Female mice from high running and control lines were either allowed (n=12, 12, respectively) or denied (n=11, 12, respectively) access to wheels for 20 months. Femoral shaft, neck, and head were measured with calipers and via micro-computed tomography. Fracture characteristics of the femoral head were assessed in cantilever bending. After adjusting for variation in body mass by two-way analysis of covariance, distal width of the femur increased as a result of selective breeding, and mediolateral femoral diameter was reduced by wheel access. Cross-sectional area of the femoral mid-shaft showed a significant linetype x activity effect, increasing with wheel access in high-running lines but decreasing in control lines. Body mass was significantly positively correlated with many of the morphometric traits studied. Fracture load of the femoral neck was strongly positively predicted by morphometric traits of the femoral neck (r2>0.30), but no significant effects of selective breeding or wheel access were found. The significant correlations of body mass with femoral morphometric traits underscore the importance of controlling for body size when analyzing the response of bone size and shape to experimental treatments. After controlling for body mass, measures of the femoral neck remain significant predictors of femoral neck strength.     

Biomechanics of the hip and birth in early Homo

A complex of traits in the femur and pelvis of Homo ereclus and early “erectus-like” specimens has been described, but never satisfactorily explained. Here the functional relationships between pelvic and femoral structure in humans are explored using both theoretical biomechanical models and empirical tests within modern samples of diverse body form (Pecos Amerindians, East Africans). Results indicate that a long femoral neck increases mediolateral bending of the femoral diaphysis and decreases gluteal abductor and hip joint reaction forces. Increasing biacetabular breadth along with femoral neck length further increases M-L bending of the femoral shaft and maintains abductor and joint reaction forces at near “normal” levels. When compared to modern humans, Homo erectus and early “erectus-like” specimens are characterized by a long femoral neck and greatly increased M-L relative to A-P bending strength of the femoral shaft, coupled with no decrease in hip joint size and a probable increase in abductor force relative to body size. All of this strongly suggests that biacetabular breadth as well as femoral neck length was relatively large in early Homo. Several features preserved in early Homo partial hip bones also indicate that the true (lower) pelvis was very M-L broad, as well as A-P narrow. This is similar to the lower pelvic shape of australopithecines and suggests that nonrotational birth, in which the newborn's head is oriented transversely through the pelvic outlet, characterized early Homo as well as Australopithecus. Because M-L breadth of the pelvis is constrained by other factors, this may have limited increases in cranial capacity within Homo until rotational birth was established during the late Middle Pleistocene. During or after the transition to rotational birth biacetabular breadth decreased, reducing the body weight moment arm about the hip and allowing femoral neck length (abductor moment arm) to also decrease, both of which reduced M-L bending of the proximal femoral shaft. Variation in femoral structural properties within early Homo and other East African Early Pleistocene specimens has several taxonomic and phylogenetic implications. © 1995 Wiley-Liss, Inc.     

Fracture mechanics of the femoral neck in a composite bone model: Effects of platen geometry

Load applicator (platen) geometry used for axial load to failure testing of the femoral neck varies between studies and the biomechanical consequences are unknown. The purpose of this study was to determine if load application with a flat versus a conical platen results in differing fracture mechanics. Femurs were aligned in 25° of adduction and an axial compressive force was applied to the femoral heads at a rate of 6 mm/min until failure. Load application with the conical platen resulted in an average ultimate failure load, stiffness, and energy to failure of 9067 N, 4033 N/mm, and 12.12 J, respectively. Load application with the flat platen resulted in a significant (p<0.05) reduction in ultimate failure load (7620 N) and stiffness (2924 N/mm). Energy to failure (12.30 J) was not significantly different (p=0.893). Different fracture patterns were observed for the two platens and the conical platen produced fractures more similar to clinical observations. Use of a flat platen underestimates the strength and stiffness of the femoral neck and inaccurately predicts the associated fracture pattern. These findings must be considered when interpreting the results of prior biomechanical studies on femoral neck fracture and for the development of future femoral neck fracture models.     

Shade induced changes in biomechanical petiole properties in the stoloniferous herb <Emphasis Type="Italic">Trifolium repens</Emphasis>

Increased cell number and cell length both contribute to shade induced elongation of petioles which enables stoloniferous plants to place their leaf lamina higher up in the canopy. Although petiole elongation is assumed to be beneficial, it may also imply costs in terms of decreased biomechanical stability. We test the hypothesis that shade induced elongation changes the biomechanical properties of petioles and that the underlying mechanisms, cell division and cell elongation, differentially affect biomechanical properties. This was done by subjecting 14 genotypes differing in the relative contribution of cell size and cell number to shade induced elongation responses to high light conditions and to simulated canopy shade. Developmental traits (cell size and cell number), morphological traits characterizing the petioles, as well as biomechanical characteristics were measured. Our results show that, comparable to stems of non-clonal plants, the rigidity of a petiole’s tissue (the Young’s modulus) increases, leading to increased flexural stiffness of petioles subjected to shading. Increased flexural stiffness proved to be associated with increased performance under shaded conditions. Our results also indicate that cell number affected the material properties and the flexural stiffness of petioles. However, the degree and pattern of the effects differed between light environments. Shade induced increase in cell number translated into shade induced increase of Young’s modulus and flexural stiffness. Genotypes producing relatively larger cells under shaded conditions experienced a decrease in tissue rigidity. In concert our results indicate that the pattern of selection on flexural stiffness, and thereby also on shade induced changes of cell number and cell size differs among light environments. An erratum to this article can be found at     

Biomechanical properties of bones from rats treated with sevelamer

Sevelamer hydrochloride is used for ten years in patients on dialysis as a phosphate binder. We have previously shown that oral application of sevelamer prevents the bone loss and increases the bone volume in ovariectomized rats. In this study we further analysed the biomechanical properties of bones from rats treated with sevelamer utilizing a threepoint bending test to determine the mechanical properties of the cortical bone of the mid-shaft femur, while the indentation test was used to determine the mechanical properties of cancellous bone in the marrow cavity of the distal femoral metaphysis. Parameters analyzed included: maximum load (F(u)), stiffness (S), energy absorbed (W), toughness (T) and ultimate strength (sigma). The intrinsic properties, stress, elastic modulus and toughness were determined from measured maximum load, strains, stiffness, energy absorbed, outer and inner diameters, and calculated bone cross-sectional moment of inertia. Sevelamer was given to rats for 25 weeks with a content of 3% of sevelamer in a standard diet, starting immediately following ovariectomy (OVX). Animals were divided to the following groups: (1) Sham; (2) Sham + sevelamer 3%; (3) OVX; (4) OVX + sevelamer 3%. Our results showed that sevelamer particularly influenced the rat trabecular bone by increasing the maximum load for 26.2%, energy absorbed for 24.2% and the ultimate strength for 26.2% in sham animals treated with sevelamer 3%, as compared to sham rats. Sevelamer 3% in OVX rats also increased the maximum load for 71.4%, stiffness for 70.7%, energy absorbed for 55.9% and the ultimate strength for 71.3% as compared to OVX controls. In the three bending test sevelamer had a very little effect on preventing loss of bone strenght in the cortical bone. These results collectively suggest that sevelamer improves bone biomechanical properties, mainly affecting trabecular bone quality in both normal and ovariectomized rats.     

An apparatus for tensile and bending tests of perinatal, neonatal, pediatric and adult cadaver osteoligamentous cervical spines

Investigations of biomechanical properties of pediatric cadaver cervical spines subjected to tensile or bending modes of loading are generally limited by a lack of available tissue and limiting sample sizes, both per age and across age ranges. It is therefore important to develop fixation techniques capable of testing individual cadavers in multiple modes of loading to obtain more biomechanical data per subject. In this study, an experimental apparatus and fixation methodology was developed to accommodate cadaver osteoligamentous head-neck complexes from around birth (perinatal) to full maturation (adult) [cervical length: 2.5-12.5 cm; head breadth: 6-15 cm; head length: 6-19 cm] and sequentially test the whole cervical spine in tension, the upper cervical spine in bending and the upper cervical spine in tension. The experimental apparatus and the fixation methodology provided a rigid casting of the head during testing and did not compromise the skull. Further testing of the intact skull and sub-cranial material was made available due to the design of the apparatus and fixation techniques utilized during spinal testing. The stiffness of the experimental apparatus and fixation technique are reported to better characterize the cervical spine stiffness data obtained from the apparatus. The apparatus and fixation technique stiffness was 1986 N/mm. This experimental system provides a stiff and consistent platform for biomechanical testing across a broad age range and under multiple modes of loading.     

Beneficial effect of zinc supplementation on biomechanical properties of femoral distal end and femoral diaphysis of male rats chronically exposed to cadmium

The present study was aimed at estimate, based on the rat model of human moderate and relatively high chronic exposure to cadmium (Cd), whether zinc (Zn) supplementation may prevent Cd-induced weakening in the bone biomechanical properties. For this purpose, male Wistar rats were administered Cd (5 or 50 mg/l) or/and Zn (30 or 60 mg/l) in drinking water for 6 and 12 months. Bone mineral density (BMD) and biomechanical properties (yield load, ultimate load, post-yield load, displacement at yield and at ultimate, stiffness, work to fracture, yield stress, ultimate stress and Young modulus of elasticity) of the femoral distal end and femoral diaphysis were examined. Biomechanical properties of the distal femur were estimated in a compression test, whereas those of the femoral diaphysis -- in a three-point bending test. Exposure to Cd, in a dose and duration dependent manner, decreased the BMD and weakened the biomechanical properties of the femur at its distal end and diaphysis. Zn supplementation during Cd exposure partly, but importantly, prevented the weakening in the bone biomechanical properties. The favorable Zn influence seemed to result from an independent action of this bioelement and its interaction with Cd. However, Zn supply at the exposure to Cd had no statistically significant influence on the BMD at the distal end and diaphysis of the femur. The results of the present paper suggest that Zn supplementation during exposure to Cd may have a protective influence on the bone tissue biomechanical properties, and in this way it can, at least partly, decrease the risk of bone fractures. The findings seem to indicate that enhanced dietary Zn intake may be beneficial for the skeleton in subjects chronically exposed to Cd.     

Mineral density and biomechanical properties of bone tissue from male Arctic foxes (Vulpes lagopus) exposed to organochlorine contaminants and emaciation

We investigated the impact from dietary OC (organochlorine) exposure and restricted feeding (emaciation) on bone mineral density (BMD; g hydroxy-apatite cm(-2)) in femoral, vertebrate, skull and baculum osteoid tissue from farmed Arctic blue foxes (Vulpes lagopus). For femur, also biomechanical properties during bending (displacement [mm], load [N], energy absorption [J] and stiffness [N/mm]) were measured. Sixteen foxes (EXP) were fed a wet food containing 7.7% OC-polluted minke whale (Balaenoptera acutorostrata) blubber in two periods of body fat deposition (Aug-Dec) and two periods of body fat mobilisation (Jan-July) in which the food contained less energy and only 2% blubber. SigmaOC food concentration in the food containing 7.7% whale blubber was 309 ng/g wet mass. This corresponded to a SigmaOC exposure of ca. 17 microg/kg body mass/d and a responding SigmaOC residue in subcutaneous adipose tissue of ca. 1700 ng/g live mass in the 8 EXP fat foxes euthanized after 16 months. A control group (CON) composed of 15 foxes were fed equal daily caloric amounts of clean pork (Sus scrofa) fat. After 16 months, 8 EXP and 7 CON foxes were euthanized (mean body mass=9.25 kg) while the remaining 8 EXP and 8 CON foxes were given restricted food rations for 6 months resulting in a body weight reduction (mean body mass=5.46 kg). The results showed that only BMD(skull) vs. BMD(vertebrae) were significantly correlated (R=0.68; p=0.03; n=10) probably due to a similar composition of trabecular and cortical osteoid tissue. No difference in any of the BMD measurements or femoral biomechanical properties was found between EXP and CON foxes although BMD baculum was 1.6-folds lower in the EXP group. However, lean summer foxes had significantly lower femoral biomechanical properties measured as displacement (mm), energy absorption (J) and time (s) biomechanical properties than fat winter foxes (all p<0.004). This indicates lower stiffness and softer bones from fasting which is in agreement with previous studies. Further, it should be kept in mind when studying bone tissues in Arctic mammals also in order to avoid confounding effects from body condition.     

Biomechanical evaluation of a novel lumbosacral axial fixation device

BACKGROUND: Interbody arthrodesis is employed in the lumbar spine to eliminate painful motion and achieve stability through bony fusion. Bone grafts, metal cages, composite spacers, and growth factors are available and can be placed through traditional open techniques or minimally invasively. Whether placed anteriorly, posteriorly, or laterally, insertion of these implants necessitates compromise of the anulus--an inherently destabilizing procedure. A new axial percutaneous approach to the lumbosacral spine has been described. Using this technique, vertical access to the lumbosacral spine is achieved percutaneously via the presacral space. An implant that can be placed across a motion segment without compromise to the anulus avoids surgical destabilization and may be advantageous for interbody arthrodesis. The purpose of this study was to evaluate the in vitro biomechanical performance of the axial fixation rod, an anulus sparing, centrally placed interbody fusion implant for motion segment stabilization. METHOD OF APPROACH: Twenty-four bovine lumbar motion segments were mechanically tested using an unconstrainedflexibility protocol in sagittal and lateral bending, and torsion. Motion segments were also tested in axial compression. Each specimen was tested in an intact state, then drilled (simulating a transaxial approach to the lumbosacral spine), then with one of two axial fixation rods placed in the spine for stabilization. The range of motion, bending stiffness, and axial compressive stiffness were determined for each test condition. Results were compared to those previously reported for femoral ring allografts, bone dowels, BAK and BAK Proximity cages, Ray TFC, Brantigan ALIF and TLIF implants, the InFix Device, Danek TIBFD, single and double Harms cages, and Kaneda, Isola, and University plating systems. RESULTS: While axial drilling of specimens had little effect on stiffness and range of motion, specimens implanted with the axial fixation rod exhibited significant increases in stiffness and decreases in range of motion relative to intact state. When compared to existing anterior, posterior, and interbody instrumentation, lateral and sagittal bending stiffness of the axial fixation rod exceeded that of all other interbody devices, while stiffness in extension and axial compression were comparable to plate and rod constructs. Torsional stiffness was comparable to other interbody constructs and slightly lower than plate and rod constructs. CONCLUSIONS: For stabilization of the L5-S1 motion segment, axial placement of implants offers potential benefits relative to traditional exposures. The preliminary biomechanical data from this study indicate that the axial fixation rod compares favorably to other devices and may be suitable to reduce pathologic motion at L5-S1, thus promoting bony fusion.     

The effects of damage and microcracking on the impact strength of bone

Microcracking has been shown to occur when bone is 'damaged' as shown by a loss of stiffness. The effect on bone's toughness of the types of damage produced at low losses of stiffness are not known. We loaded bovine bone specimens in bending and tension to stiffness losses of up to 27%, and examined the microcracking produced. The tensile specimens had diffuse arrays of microcracks of 2-20 microm in length, characteristic of tensile loading, on all surfaces. The bending specimens showed tensile microcracking on the tensile surface and characteristic long, straight, cross-hatched compression cracks on the compressive surface. Specimens were then broken in impact. Those that had been damaged in bending were divided into two groups, in one group the part of the specimen which had undergone compression damage was placed in tension, and in the other group the tensile damage was placed in tension. Tensile damage loaded in tension did not reduce the bone's energy-absorbing ability in impact until a modulus reduction of over 20%. However compression damage loaded in tension did severely reduce the bone's energy absorption capabilities (by an average of about 40%).     

The fixion proximal femur nailing system: biomechanical properties of the nail and a cadaveric study

The treatment of choice for early mobilization of hip fracture is surgery, which traditionally employs side plates and screws or intramedullary nails. We examined the biomechanical properties of a new proximal femoral nail system. The new expandable Fixion proximal femur nailing (PFN) system, made of stainless-steel alloy, consists of a nail, a peg and an anti-rotation pin. Upon positioning, the nail and peg are expanded to their maximal diameter. The current biomechanical study investigated: nail bending strength and stiffness, fatigue properties and hip peg strength. A cadaveric study that determined the effect of the expandable peg on the femoral head included subsidence testing, pull and torsion testing and intra-osseous pressure (IOP) measurements before and after expansion. Biomechanical properties of the new nail met ASTM F384 guideline requirements. The cadaver study yielded equivalent results for the pullout test between the peg and the hip screw, but found the peg superior in the torsion strength test. IOP during peg insertion and expansion was substantially lower than the threshold pressure that causes avascular necrosis. The biomechanical tests found the new system to be safe and able to provide good abutment of the nail to the bone. We conclude that the Fixion PFN system proved to be an effective proximal femur fracture fixation device.     

Cut type femur neck prosthesis--a functional morphologic analysis]

In contrast to other commonly employed models, the cut model femoral neck prosthesis is a cementless prosthesis of comparatively small dimensions. With the aim of investigating its functional integration in the femur, radiological, densitometric and photoelastic analyses were carried out. The biomechanical reaction of the bone tissue expected on the basis of the experimental result is tested in the clinical situation.     

The crown joules: energetics,ecology, and evolution in humans and other primates

Biological diversity is metabolic diversity: Differences in anatomy, physiology, life history, and activity reflect differences in energy allocation and expenditure among traits and tasks. Traditional frameworks in primatology, human ecology, public health, and paleoanthropology view daily energy expenditure as being more variable within than between species, changing with activity level but essentially fixed for a given body size. Growing evidence turns this view on its head. Total energy expenditure (kcal/d), varies relatively little within species, despite variation in physical activity; it varies considerably among species even after controlling for the effect of body size. Embracing this emerging paradigm requires rethinking potential trade‐offs in energy allocation within and between species, assessing evidence of metabolic acceleration within lineages, and abandoning activity‐based estimates of total energy expenditure. Difficult and exciting work lies ahead in the effort to untangle the ecological and evolutionary pressures shaping primate metabolic diversity.     

Biomechanical and clinical alterations of the hip joint following femoral neck fracture and implantation of bipolar hip endoprosthesis

The implantation of a bipolar partial hip endoprosthesis is a treatment of choice for displaced medial femoral neck fracture. We present an experimental study which asses and compare biomechanical and clinical status through period before and after hip fracture and implantation of bipolar partial hip endoprosthesis. This study encompassed 75 patients who suffered from an acute medial femoral neck fracture and were treated with the implantation of a bipolar partial hip endoprosthesis. Their biomechanical status (stress distribution on the hip joint weight bearing area) and clinical status (Harris Hip Score) were estimated for the time prior to the injury and assessed at the follow-up examination that was, on average, carried out 40 months after the operation. Despite ageing, the observed Harris Hip Score at the follow-up examination was higher than that estimated prior to the injury (77.9 > 69.6; p = 0.006). Similarly, the hip stress distribution was reduced (2.7 MPa < 2.3 MPa; p = 0.001). While this reduction can be attributed to a loss of weight due to late ageing, the principal improvement came from the operative treatment and corresponding restoration of the biomechanical properties of the hip joint. The implantation of a bipolar partial hip endoprosthesis for patients with displaced medial femoral neck fractures improves the biomechanical and clinical features of the hip, what should have on mind during making decision about treatment.     

Growth-dependent effects of dietary protein concentration and quality on the biomechanical properties of the diaphyseal rat femur

ObjectivesThis study compares the effects of feeding growing rats with increasing concentrations of casein (C) and wheat gluten (G), proteins that show different biological qualities, on the morphometrical and biomechanical properties of the femoral diaphysis.Materials and methodsFemale rats were fed with one of ten diets containing different concentrations (5–30%) of C and G between the 30th and 90th days of life (Control = C-20%). Biomechanical structural properties of the right femur middiaphysis were estimated using a 3-point bending mechanical test with calculation of some indicators of bone material properties.ResultsBody weight and length were affected by treatments, values being highest in rats fed the C-20% diet. G diets affected negatively both parameters. Changes in cross-sectional geometry (mid-diaphyseal cross-sectional and cortical areas, femoral volume, and rectangular moment of inertia) were positively related to the C content of the diet, while they were severely and negatively affected by G diets. Similar behaviors were observed in the bone structural properties (fracture load, yielding load, diaphyseal stiffness and elastic energy absorption). When values of strength and stiffness were normalized for body weight, the differences disappeared. The bone material quality indicators (elastic modulus, yielding stress, elastic energy absorption/volume) did not differ significantly among all studied groups. Femoral calcium concentration in ashes was not significantly different among groups.ConclusionThe clear differences in strength and stiffness of bone beams induced by dietary protein concentration and quality seemed to be the result of an induced subnormal gain in bone structural properties as a consequence of a correlative subnormal gain in bone growth and mass, yet not in bone material properties.     

The Effect of Long-Term Extremely Low-Frequency Magnetic Field on Geometric and Biomechanical Properties of Rats' Bone

Bone is composed of a mineral matrix reinforced by a network of collagen that governs the biomechanical functions of the skeletal system in the body. The purpose of the study was to investigate the possible effect of extremely low-frequency magnetic field (ELF-MF) on geometric and biomechanical properties of rats' bone. In this study, 30 male Sprague-Dawley rats were used. The rats were divided into three groups: two experimental and one control sham. The first and second experimental group (n=10) were exposed to 100?μT and 500?μT-MF during 10 months, 2?h a day, respectively, and the third (sham) (n=10) group was treated like experimental group except ELF-MF exposure in methacrylate boxes. After ELF-MF and sham exposure, geometric and the biomechanical properties of rats' bone, such as cross-sectional area of the femoral shaft, length of the femur, cortical thickness of the femur, ultimate tensile strength (maximum load), displacement, stiffness, energy absorption capacity, elastic modulus, and toughness of bone were determined. The geometric and biomechanical analyses showed that a significant decrease in rats exposed to 100?μT-MF in comparison to sham and 500?μT-MF exposed rats about the values of cross-sectional area of the femoral shaft (P<0.05). Maximum load increased in 100?μT-MF and 500?μT-MF exposed rats when compared to that of the sham rats (P<0.05). The cortical thickness of the femurs of MF-exposed rats (100?μT and 500?μT) were significantly decreased in comparison to that of sham groups' rats (P<0.05 and P<0.001). However, no significant differences were found in the other biomechanical endpoints between each other groups, such as: length of the femur, displacement, stiffness, energy absorption capacity, elastic modulus, and toughness of bone (P>0.05). These experiments demonstrated that 100?μT-MF and 500?μT-MF can affect biomechanical and geometrical properties of rats' bone.     

The effects of quercetin on bone minerals, biomechanical behavior, and structure in streptozotocin-induced diabetic rats

This study was designed to investigate the effect of quercetin (QE) on bone minerals and biomechanics in insulin-dependent diabetic rats. Diabetes was induced by 50 mg kg(-1) intraperitoneal streptozotocin (STZ) in a single dose. The rats were randomly allotted into four experimental groups: A (control), B (non-diabetic + QE), C (diabetic), and D (diabetic + QE) each containing 10 animals. The diabetic rats received QE (15 mg kg(-1) day(-1)) for 4 weeks following 8 weeks of STZ injection. Blood samples were taken to determine glucose, insulin, calcium, and magnesium levels. The rats' femora were assessed biomechanically at femoral mid-diaphysis and neck. It was found that QE treatment increased insulin, calcium, and magnesium levels. Three-point bending of the femoral mid-diaphysis and necks showed significantly lower maximum load values (F max) in animals in the STZ group than the QE + STZ or control groups (p < 0.05). The results support the conclusion that QE treatment may decrease blood glucose and increase plasma insulin, calcium, and magnesium. QE treatment may also be effective in bone mineral metabolism, biomechanical strength, and bone structure in STZ-induced diabetic rats.     

Mechanisms of uniformity of yield strains for trabecular bone

Variations in yield strains for trabecular bone within a specific anatomic site are only a small fraction of the substantial variations that exist for elastic modulus and strength, and yet the source of this uniformity is not known. Our goal was to investigate the underlying mechanisms by using high-resolution, materially nonlinear finite element models of 12 human femoral neck trabecular bone specimens. The finite element models, used to obtain apparent yield strains in both tension and compression, assumed that the tissue-level yield strains were the same across all specimens. Comparison of the model predictions with the experimental data therefore enabled us to isolate the combined roles of volume fraction and architecture from the role of tissue material properties. Results indicated that, for both tensile and compressive loading, natural variations in volume fraction and architecture produced a negligible coefficient of variation (less than 3%) in apparent yield strains. Analysis of tissue-level strains showed that while bending of individual trabeculae played only a minor role in the apparent elastic behavior, the combined effects of this bending and tissue-level strength asymmetry produced apparent-level failure strains in compression that were 14% lower than those at the tissue level. By contrast, tissue and apparent-level yield strains were equivalent for tensile loading. We conclude that the uniformity of apparent yield strains is primarily the result of the highly oriented architecture that minimizes bending. Most of the variation that does occur is the result of the non-uniformity of the tissue-level yield strains.     

Bone mineral density and bone structure parameters as predictors of bone strength: an analysis using computerized microtomography and gastrectomy-induced osteopenia in the rat

In this study the relationships of bone mineral density (BMD) and bone structure parameters calculated from 2D microtomography images to bone strength were investigated. Femurs from 21 male Sprague Dawley rats were subjected to dual-energy X-ray absorptiometry, computerized microtomography (CmicroT) and either three-point cantilever bending (femoral shaft) or two-point bending compression (femoral neck). Gastrectomy was performed on 12 animals and 9 were sham operated. From the tomograms bone structure analysis was performed using a software routine based on grey level run-length method. Correlations of BMD and bone structure parameters to mechanical parameters were investigated as were differences between the gastrectomized and the control samples. The reductions of BMD between the groups were 21 and 27% in the femoral neck and shaft, respectively. For the shaft, the correlations of BMD to all mechanical parameters were significant and BMD was a consistent predictor of bone strength for cortical bone. However, in the femoral neck where cancellous bone predominates, BMD was weakly correlated only to deflection. A significant correlation between trabecular thickness and neck bone strength was found. Hence, compared to trabecular thickness, BMD was of limited value in predicting bone strength in the femoral neck.     

Craniofacial variation,body size and ecological factors in aboriginal populations from central Patagonia (2000–200 years B.P.)

Previous studies have shown that ecological factors had a significant role in shaping the patterns of craniofacial variation among South American populations. Here, we evaluate whether temperature and diet contributed to facial diversification in small geographic areas. Facial size and shape of 9 osteological samples from central Patagonia (Argentina) were described using 2D landmarks and semilandmarks. Data on mean annual temperature, diet composition (δ¹³C and δ¹⁵N values) and femoral head maximum breadth, used as a proxy of body mass, were obtained for each sample. We then tested the association of body mass and the ecological variables with facial morphology using spatial regression techniques and a model selection approach. Akaike Information Criterion produced disparate results for both components of facial morphology. The best model for facial size included temperature and body mass proxy, and accounted for more than 80% of variation in size. Lower temperatures were related to larger facial sizes. Body mass was negatively associated with facial size and showed no relationship with the temperature. This suggests a relatively independent variation of cranial traits and body mass at the spatial scale studied here. Facial shape was not associated with the temperature or diet composition, contrasting with the patterns observed at larger spatial scales. Our results point out that the effect of climatic variables on cranial traits might be a source of morphological differentiation not only at large scales but also in small geographic areas, and that size and shape display a differential preservation of environmental signals.