Stimulation of methanol degradation in UASB reactors: in situ versus pre-loading cobalt on anaerobic granular sludge

The effect of pre-loading and in situ loading of cobalt onto a cobalt-limited granular sludge on the performance of methanol fed bioreactors was investigated. One upflow anaerobic sludge bed (UASB) reactor was inoculated with cobalt pre-loaded sludge (24h; 30 degrees C; 1 mM CoCl2) and a second UASB with unloaded sludge. The UASB reactors (30 degrees C; pH 7) were operated for 77 days at 8 h hydraulic retention time and organic loading rates ranging from 5 to 20 g COD.L reactor(-1).d(-1). Cobalt pre-loading clearly stimulated the methanogenic activity of the sludge with methanol as the substrate, e.g., after 30 days of reactor operation this activity was 5.8 times higher than that of the cobalt unloaded sludge. During the experiment, part of the cobalt leached from the pre-loaded sludge, i.e., 54% of the cobalt content was lost during the 77 days of reactor operation. Sequential metal extraction showed that losses mainly occurred from the exchangeable and carbonate fraction and in the sludge remaining cobalt was mainly present in the organic/sulfide fraction of the sludge. In situ loading of cobalt in the unloaded UASB reactor on day 57 by adding 31 microM cobalt to the influent for a 24-h period (16% of the cobalt present in the loaded sludge at day 11) resulted in a 4 time increase of the methanogenic activity of the sludge with methanol as the substrate at the end of the reactor experiment, while the accumulated amount of cobalt in the sludge only amounted to 6% of the cobalt accumulated in the loaded sludge (on day 11). This study showed that both pre-loading sludge and in situ loading are adequate for achieving an increased reactor performance of methanol fed UASB reactors operating under cobalt limitation. However, the in situ dosing procedure needs substantially lower amounts of cobalt, while it also gives significantly smaller losses of cobalt with the effluent.     

Effect of sulfur source on the performance and metal retention of methanol-fed UASB reactors

The effect of a sulfur source on the performance and metal retention of methanol-fed upflow anaerobic sludge bed (UASB) reactors was investigated. For this purpose, two UASB reactors were operated with cobalt preloaded granular sludge (1 mM CoCl2; 30 degrees C; 24 h) at an organic loading rate (OLR) of 5 g COD.L reactor(-1).d(-1). One UASB reactor (R1) was operated without a sulfur source in the influent during the first 37 days. In this period the methanol conversion to methane remained very poor, apparently due to the absence of a sulfur source, because once cysteine, a sulfur-containing amino acid, was added to the influent of R1 (day 37) a full conversion of methanol to methane occurred within 6 days. The second reactor (R2) was operated with sulfate (0.41 mM) in the influent during the first 86 days of operation, during which no limitation in the methanol conversion to methane manifested. Cobalt washed out from the sludge at similar rates in both reactors. The leaching of cobalt occurred at two distinct rates, first at a high rate of 22 microg.g TSS(-1).d(-1), which proceeded mainly from the exchangeable and carbonate fraction and later at a relatively slow rate of 9 mug.g TSS(-1).d(-1) from the organic/sulfide fraction. This study showed that the supply of the sulfur source L-cysteine has a pronounced positive effect on the methanogenic activity and the retention of metals such as iron, zinc and molybdenum.     

Acidification of methanol-fed anaerobic granular sludge bioreactors by cobalt deprivation: Induction and microbial community dynamics

The acidification of mesophilic (30 degrees C) methanol-fed upflow anaerobic sludge bed (UASB) reactors induced by cobalt deprivation from the influent was investigated by coupling the reactor performance (pH 7.0; organic loading rate 4.5 g COD . L(-1) . d(-1)) to the microbial ecology of the bioreactor sludge. The latter was investigated by specific methanogenic activity (SMA) measurements and fluorescence in situ hybridization (FISH) to quantify the abundance of key organisms over time. This study hypothesized that under cobalt limiting conditions, the SMA on methanol of the sludge gradually decreases, which ultimately results in methanol accumulation in the reactor effluent. Once the methanol accumulation surpasses a threshold value (about 8.5 mM for the sludge investigated), reactor acidification occurs because acetogens outcompete methylothrophic methanogens at these elevated methanol concentrations. Methanogens present in granular sludge at the time of the acidification do not use methanol as the direct substrate and are unable to degrade acetate. Methylotrophic/acetoclastic methanogenic activity was found to be lost within 10 days of reactor operation, coinciding with the disappearance of the Methanosarcina population. The loss of SMA on methanol can thus be used as an accurate parameter to predict reactor acidification of methanol-fed UASB reactors operating under cobalt limiting conditions.     

Role of nickel in high rate methanol degradation in anaerobic granular sludge bioreactors

The effect of nickel deprivation from the influent of a mesophilic (30 degrees C) methanol fed upflow anaerobic sludge bed (UASB) reactor was investigated by coupling the reactor performance to the evolution of the Methanosarcina population of the bioreactor sludge. The reactor was operated at pH 7.0 and an organic loading rate (OLR) of 5-15 g COD l(-1) day(-1) for 191 days. A clear limitation of the specific methanogenic activity (SMA) on methanol due to the absence of nickel was observed after 129 days of bioreactor operation: the SMA of the sludge in medium with the complete trace metal solution except nickel amounted to 1.164 (+/-0.167) g CH(4)-COD g VSS(-1) day(-1) compared to 2.027 (+/-0.111) g CH(4)-COD g VSS(-1) day(-1) in a medium with the complete (including nickel) trace metal solution. The methanol removal efficiency during these 129 days was 99%, no volatile fatty acid (VFA) accumulation was observed and the size of the Methanosarcina population increased compared to the seed sludge. Continuation of the UASB reactor operation with the nickel limited sludge lead to incomplete methanol removal, and thus methanol accumulation in the reactor effluent from day 142 onwards. This methanol accumulation subsequently induced an increase of the acetogenic activity in the UASB reactor on day 160. On day 165, 77% of the methanol fed to the system was converted to acetate and the Methanosarcina population size had substantially decreased. Inclusion of 0.5 muM Ni (dosed as NiCl(2)) to the influent from day 165 onwards lead to the recovery of the methanol removal efficiency to 99% without VFA accumulation within 2 days of bioreactor operation.     

Effect of nickel deprivation on methanol degradation in a methanogenic granular sludge bioreactor

The effect of omitting nickel from the influent on methanol conversion in an Upflow Anaerobic Sludge Bed (UASB) reactor was investigated. The UASB reactor (30°C, pH 7) was operated for 261 days at a 12-h hydraulic retention time (HRT) and at organic loading rates (OLRs) ranging from 2.6 to 7.8 g COD l reactor⁻¹ day⁻¹. The nickel content of the sludge decreased by 66% during the 261-day reactor run because of washout and doubling of the sludge bed volume. Nickel deprivation initially had a strong impact on the methanogenic activity of the sludge with methanol; e.g., after 89 days of operation, this activity was doubled by adding 2 μM nickel. Upon prolonged UASB reactor operation, methanol and VFA effluent concentrations decreased whereas the sludge lost its response to nickel addition in activity tests. This suggests that a less nickel-dependent methanol-converting sludge had developed in the UASB reactor. Received 09 April 2002/ Accepted in revised form 13 July 2002     

High-rate sulfate reduction at high salinity (up to 90 mS.cm(-1)) in mesophilic UASB reactors

Sulfate reduction in salt-rich wastewaters using unadapted granular sludge was investigated in 0.9 L UASB reactors (pH 7.0 +/- 0.2; hydraulic retention time from 8-14 h) fed with acetate, propionate, or ethanol at organic loading rates up to 10 gCOD x L(-1) x day(-1) and in excess sulfate (COD/SO(4) (2-) of 0.5). High-rate sulfate reduction rates (up to 3.7 gSO(4) (2-) x L(-1).day(-1)) were achieved at salinities exceeding 50 gNaCl.L(-1) and 1 gMgCl(2) x L(-1). Sulfate reduction proceeded at a salinity of up to 70 gNaCl x L(-1) and 1 gMgCl(2) x L(-1) (corresponding to a conductivity of about 85-90 mS x cm(-1)), although at lower rates compared to a conductivity of 60-70 mS x cm(-1). Ethanol as well as propionate were suitable substrates for sulfate reduction, with acetate and sulfide as the end products. The successful high-rate treatment was due to the proliferation of a halotolerant incomplete oxidizing SRB population present in the unadapted inoculum sludge. Bioaugmentation of this sludge with the acetate oxidizing halotolerant SRB Desulfobacter halotolerans was unsuccessful, as the strain washed out from the UASB reactor without colonizing the UASB granules.     

Long-term competition between sulfate reducing and methanogenic bacteria in UASB reactors treating volatile fatty acids

The competition between acetate utilizing methane-producing bacteria (MB) and sulfate-reducing bacteria (SRB) was studied in mesophilic (30 degrees C) upflow anaerobic sludge bed (UASB) reactors (upward velocity 1 m h-1; pH 8) treating volatile fatty acids and sulfate. The UASB reactors treated a VFA mixture (with an acetate:propionate:butyrate ratio of 5:3:2 on COD basis) or acetate as the sole substrate at different COD:sulfate ratios. The outcome of the competition was evaluated in terms of conversion rates and specific methanogenic and sulfidogenic activities. The COD:sulfate ratio was a key factor in the partitioning of acetate utilization between MB and SRB. In excess of sulfate (COD:sulfate ratio lower than 0.67), SRB became predominant over MB after prolonged reactor operation: 250 and 400 days were required to increase the amount of acetate used by SRB from 50 to 90% in the reactor treating, respectively, the VFA mixture or acetate as the sole substrate. The competition for acetate was further studied by dynamic simulations using a mathematical model based on the Monod kinetic parameters of acetate utilizing SRB and MB. The simulations confirmed the long term nature of the competition between these acetotrophs. A high reactor pH (+/-8), a short solid retention time (<150 days), and the presence of a substantial SRB population in the inoculum may considerably reduce the time required for acetate-utilising SRB to outcompete MB.     

Effect of cobalt on the anaerobic degradation of methanol

The effect of trace elements on the methanogenesis from methanol and acetate was studied utilizing granular sludge obtained from an anaerobic wastewater treatment plant. The methanogenic activity from methanol was dramatically stimulated by the addition of a cocktail of trace elements in the basal medium. When trace elements were supplied individually, cobalt greatly stimulated methanogenesis which equalled the stimulation observed with the complete trace element mixture. No remarkable influence of any trace element was observed when acetate was used as the substrate. Two Upflow Anaerobic Sludge Blanket (UASB) reactors were operated with and without supplementation of cobalt. Cobalt greatly stimulated both acetogenesis in the initial operational phase and later methanogenesis. The cobalt sufficient column provided almost 3 times the methane productivity compared to the cobalt deprived column. At an organic loading rate of 8 g COD/l·d, 87% of the COD was converted to methane in the cobalt sufficient column. Under low cobalt concentration, methanogens compete better for cobalt than acetogens.     

Thermophilic (55-65 degrees C) and extreme thermophilic (70-80 degrees C) sulfate reduction in methanol and formate-fed UASB reactors

The feasibility of thermophilic (55-65 degrees C) and extreme thermophilic (70-80 degrees C) sulfate-reducing processes was investigated in three lab-scale upflow anaerobic sludge bed (UASB) reactors fed with either methanol or formate as the sole substrates and inoculated with mesophilic granular sludge previously not exposed to high temperatures. Full methanol and formate degradation at temperatures up to, respectively, 70 and 75 degrees C, were achieved when operating UASB reactors fed with sulfate rich (COD/SO4(2-)=0.5) synthetic wastewater. Methane-producing archaea (MPA) outcompeted sulfate-reducing bacteria (SRB) in the formate-fed UASB reactor at all temperatures tested (65-75 degrees C). In contrast, SRB outcompeted MPA in methanol-fed UASB reactors at temperatures equal to or exceeding 65 degrees C, whereas strong competition between SRB and MPA was observed in these reactors at 55 degrees C. A short-term (5 days) temperature increase from 55 to 65 degrees C was an effective strategy to suppress methanogenesis in methanol-fed sulfidogenic UASB reactors operated at 55 degrees C. Methanol was found to be a suitable electron donor for sulfate-reducing processes at a maximal temperature of 70 degrees C, with sulfide as the sole mineralization product of methanol degradation at that temperature.     

Continuous detoxification, transformation, and degradation of nitrophenols in upflow anaerobic sludge blanket (UASB) reactors

The anaerobic transformation and degradation of nitrophenols by granular sludge was investigated in upflow anaerobic sludge blanket (UASB) reactors continuously fed with a volatile fatty acid (VFA) mixture as the primary substrate. During the start-up, subtoxic concentrations of 2-nitrophenol (2-NP), 4-nitrophenol (4-NP), and 2, 4-dinitrophenol (2, 4-DNP) were utilized. 4-NP and 2, 4-DNP were readily converted to the corresponding aromatic amine; whereas 2-NP was converted to nonaromatic products via intermediate formation of 2-aminophenol (2-AP). These conversions led to a dramatic detoxification of the mononitrophenols because the reactors treated the nitrophenolics at the concentrations which were over 25 times higher than those that caused severe inhibition. VFA removal efficiencies greater than 99% were achieved in both reactors at loading rates greater than 11.4 g COD per liter of reactor volume per day even at volumetric loading of mononitrophenols up to 910 mg/L . d.The sludges obtained from each of the reactors at the end of the continuous experiments were assayed for their specific nitrophenol reducing activity in the presence of different primary substrates. Reduction rates of 45 and 26 mg/g volatile suspended solids per day were observed for 2-NP and 4-NP, respectively, when utilizing the VFA mixture as primary substrate. Hydrogen, an interspecies-reduced compound, and substrates that provide interspecies-reducing equivalents-such as butyrate, propionate, and ethanol stimulated nitrophenol reduction, whereas acetate and methanol did not. Anaerobic batch biodegradability tests with the 2-NP-adapted sludge revealed that its corresponding aromatic amine, 2-AP, was degraded to methane at a specific rate of 14.5 mg/g VSS . d. Acetate was observed to be the major intermediate during 2-AP degradation in the presence of a specific methanogenic inhibitor 2-bromoethanesulfonate. The results of this study indicate that UASB reactors can be applied to rapidly detoxify and, under certain circumstances, degrade nitroaromatic compounds. (c) 1996 John Wiley & Sons, Inc.     

Effect of long-term cobalt deprivation on methanol degradation in a methanogenic granular sludge bioreactor

The effect of the trace metal cobalt on the conversion of methanol in an upflow anaerobic sludge bed (UASB) reactor was investigated by studying the effect of cobalt deprivation from the influent on the reactor efficiency and the sludge characteristics. A UASB reactor (30 degrees C; pH 7) was operated for 261 days at a 12-h hydraulic retention time (HRT). The loading rate was increased stepwise from 2.6 g chemical oxygen demand (COD) x L reactor(-1) x d(-1) to 7.8 g COD x L reactor(-1) x d(-1). Cobalt deprivation had a strong impact on the methanogenic activity of the sludge. In batch tests, the methanogenic activity of the sludge with methanol as the substrate increased 5.3 (day 28) and 2.1 (day 257) times by addition of 840 nM of cobalt. The sludge had an apparent K(m) for cobalt of 948 nM after 28 days of operation and 442 nM at the end of the run. Cobalt deprivation during 54 days of operation led to a methanol conversion efficiency of only 55%. Continuous addition of cobalt (330 nM) for 33 days improved the methanol removal efficiency to 100%. In this period of cobalt dosing, the cobalt concentration in the sludge increased 2.7 times up to 32 microg x g TSS(-1). Upon omission of the cobalt addition, cobalt washed-out at a stable rate of 0.1 microg x g VSS(-1) x d(-1). At the end of the run, the cobalt concentration of the sludge was similar to that of the seed sludge.     

Bonding Form Analysis of Metals and Sulfur Fractionation in Methanol‐Grown Anaerobic Granular Sludge

This study investigates the metal and sulfur bonding form distribution in mesophilic (30 °C, pH 7) methanol‐grown anaerobic granular sludge from upflow anaerobic sludge bed reactors operating at an organic loading rate of 3.8 g CH₃OH‐COD/L d. This was achieved by applying a modified Tessier sequential extraction scheme to investigate the metal bonding forms and a sequential extraction scheme for sulfur and simultaneously extracted metals to granular sludge samples of the reactors after 0, 22, 35 and 43 days of operation. Metals were also determined in the sulfur extracts. Co and Ni predominated in their oxidizable bonding forms, which increased together with the pseudo‐total content during reactor operation. An omission of Co and Ni from the influent led to only a minor decline of the pseudo‐total content in the sludge, mainly from the acid‐soluble fraction. The ratio of simultaneously extracted metals (Co, Fe, Mn, Ni) to acid‐volatile sulfides was lower than 1, indicating that the sludge contained sufficient sulfide to bind the metals as metal monosulfides. The bioavailability of metals in the methanol‐grown anaerobic granular sludge investigated is therefore mainly controlled by sulfide formation/dissolution.     

Development of thermophilic methanogenic sludge in compartmentalized upflow reactors

The characteristics and development of thermophilic anaerobic sludge in upflow staged sludge bed (USSB) reactors were studied. The compartmentalized reactors were inoculated with partially crushed mesophilic granular sludge and then fed with either a mixture of volatile fatty acids (VFA) or a mixture of sucrose and VFA. The staged degradation of the soluble substrate in the various compartments led to a clear segregation of specific types of biomass along the height of the reactor, particularly in reactors fed with the sucrose-VFA mixture. Both the biological as well as the physical properties of the cultivated sludge were affected by the fraction of nonacidified substrate. The sludge in the first compartment of the reactor treating the sucrose-VFA mixture was whitish and fluffy, most likely resulting from the development of acidifying bacteria. Sludge granules which developed in the top part of this reactor possessed the highest acetogenic and methanogenic activity and the highest granule strength as well. The experiments also revealed that the conversion of the sucrose-VFA mixture into methane gradually deteriorated at prolonged operation at high organic loading rates (50 to 100 g COD . L(-1) . day(-1)). Stable long-term performance of a reactor can only be achieved by preserving the sludge segregation along the height of the reactor. In the reactor fed solely with the VFA mixture little formation of granular sludge occurred. In this reactor, large differences in sludge characteristics were also observed along the reactor height. Li(+)-tracer experiments indicated that the hydraulic regime in the USSB reactor is best characterized by a series of at least five completely mixed reactors. The formation of granular sludge was found to influence the liquid flow pattern. (c) 1996 John Wiley & Sons, Inc.     

Flocculants effect in biomass retention in a UASB reactor treating dairy manure

The performance and biomass retention of an upflow anaerobic sludge bed (UASB) reactor treating liquid fraction of dairy manure has been investigated at several organic loading rates. Two identical UASB reactors were employed. The biomass of one UASB reactor (FBR) had previously been treated with a cationic polyacrylamide, the other reactor was operated as a control reactor (CR). At 3 and 2 days of HRT both reactors functioned similarly, but at 1.5 days HRT some differences were observed between both effluents. Mean COD(T) removal percentages were 83.4% and 76.5%; COD(VFA) values in effluents were 977 and 2682 mg l(-1) for the FBR and the CR respectively. The VSS initial value in both reactors was 25.66 g VSS, whereas after the experiment the quantities were 31.83 g VSS in the FBR and 23.18 g VSS in the CR reactors. Polymer addition resulted in a higher degree of biomass retention and better performance in the FBR reactor.     

Anaerobic granule development for removal of pentachlorophenol in an upflow anaerobic sludge blanket (UASB) reactor

The granulation process using synthetic wastewater containing pentachlorophenol (PCP) in four 1.1 l laboratory scale upflow anaerobic sludge blanket (UASB) reactors was studied, and the anaerobic biotransformation of PCP during the granulation process investigated. After 110 days granular sludge was developed and up to 160 and 180 mg/l of PCP was added into the reactors R1 and R2, respectively, when they were inoculated with acclimated anaerobic sludge from an anaerobic digester of a citric acid plant. The inoculum was predominately composed of bacilli and filamentous bacteria. Granulation did not occur in reactors R3 and R4 which were inoculated with acclimated anaerobic sludge from aerobic sludge of the municipal sewage treatment plant which consisted mainly of cocci. Despite similar bacilli in the granule, the filamentous bacteria from reactor R1 were thicker than those of reactor R2. The granular sludge had a maximum diameter of 2.5 and 2.2 mm, and SMA of 1.44 and 1.32 gCOD/gTVS per day for reactors R1 and R2, respectively. Over 98% chemical oxygen demand (COD) removal rate and 99% of PCP removal rate were achieved when reactors R1 and R2 were operated at PCP and COD loading rates of 150 and 7.5 g/l per day, respectively. H₂-producing acetogens were the dominant anaerobes in the granular sludge.     

Development of a novel process for the biological conversion of H2S and methanethiol to elemental sulfur

The feasibility of anaerobic treatment of wastewater containing methanethiol (MT), an extremely volatile and malodorous sulfur compound, was investigated in lab-scale bioreactors. Inoculum biomass originating from full-scale anaerobic wastewater treatment facilities was used. Several sludges, tested for their ability to degrade MT, revealed the presence of organisms capable of metabolizing MT as their sole source of energy. Furthermore, batch tests were executed to gain a better understanding of the inhibition potential of MT. It was found that increasing MT concentrations affected acetotrophic organisms more dramatically than methylotrophic organisms. Continuous reactor experiments, using two lab-scale upflow anaerobic sludge bed (UASB) reactors (R1 and R2), aimed to determine the maximal MT load and the effect of elevated sulfide concentrations on MT conversion. Both reactors were operated at a hydraulic retention time (HRT) of about 7 hours, a temperature of 30 degrees C, and a pH of between 7.3 and 7.6. At the highest influent MT concentration applied, 14 mM in R1, corresponding to a volumetric loading rate of about 50 mM MT per day, 87% of the organic sulfur was recovered as hydrogen sulfide (12.2 mM) and the remainder as volatile organic sulfur compounds (VOSCs). Upon decreasing the HRT to 3.5 to 4.0 h at a constant MT loading rate, the sulfide concentration in the reactor decreased to 8 mM and MT conversion efficiency increased to values near 100%. MT conversion was apparently inhibited by the high sulfide concentrations in the reactor. The specific MT degradation rate, as determined after 120 days of operation in R1, was 2.83 +/- 0.27 mmol MT g VSS(-1) day(-1). During biological desulfurization of liquid hydrocarbon phases, such as with liquefied petroleum gas (LPG), the combined removal of hydrogen sulfide and MT is desired. In R2, the simultaneous addition of sodium sulfide and MT was therefore studied and the effect of elevated sulfide concentrations was investigated. The addition of sodium sulfide resulted in enhanced disintegration of sludge granules, causing significant washout of biomass. Additional acetate, added to stimulate growth of methanogenic bacteria to promote granulation, was hardly converted at the termination of the experimental period.     

Effects of alternative carbon sources on biological transformation of nitrophenols

The removal of nitrophenols under denitrifying conditions was studied in bench-scale upflow anaerobic sludge blanket (UASB) reactors (R1, R2, R3 and R4) using three different carbon sources. Initially acetate was used as carbon source (substrate) in all the four reactors followed by glucose and methanol. Reactor R1 was kept as control and R2, R3, R4 were fed with 30 mg/l concentration of 2-nitrophenol (2-NP), 4-nitrophenol (4-NP), and 2,4-dinitrophenol (2,4-DNP), respectively. Throughout the study the hydraulic retention time (HRT) and COD/NO₃ ^-–N ratio were kept as 24 h and 10, respectively. 2-Aminophenol (2-AP), 4-aminophenol (4-AP) and 2-amino,4-nitrophenol (2-A,4-NP) were found as the major intermediate metabolites of 2-NP, 4-NP and 2,4-DNP degradation, respectively. Methanol was found to be a better carbon source for 4-NP and 2,4-DNP degradation as compared to acetate and glucose, while 2-NP degradation was not influenced much by the change of substrate. Nitrate nitrogen removal was always more than 99%. COD removal efficiency of the nitrophenol fed reactors varied from 85.7% to 97.7%. The oxidation-reduction potential (ORP) inside the reactors dropped, up to –300 mv, with glucose as carbon source. As the reactors were switched over to methanol, ORP increased to –190 mv. The granular sludge developed inside the reactors was light brown in colour when acetate and glucose were used as substrate, which turned dark brown to black at the end of methanol run. Biomass yield in terms of volatile suspended solids was observed as 0.15, 0.089 and 0.14 g per gram of COD removal for acetate, glucose and methanol, respectively.     

Thermophilic (55 degrees C) conversion of methanol in methanogenic-UASB reactors: influence of sulphate on methanol degradation and competition

Two upflow sludge bed reactors (UASB) were operated for 80 days at 55 degrees C with methanol as the substrate with an organic loading rate (OLR) of about 20 g CODl(-1) per day and a hydraulic retention time (HRT) of 10 h. One UASB was operated without sulphate addition (control reactor-R1) whereas the second was fed with sulphate at a COD:SO4(2-) ratio of 10 (sulphate-fed reactor-R2), providing an influent sulphate concentration of 0.6 g l(-1). For both reactors, methanogenesis was the dominant process with no considerable accumulation of acetate. The methanol removal averaged 93% and 83% for R1 and R2, respectively, and total sulphate removal was achieved in the latter. The pathway of methanol conversion for both sludges was investigated by measuring the fate of carbon in the presence and absence of bicarbonate or specific inhibitors for a sludge sample collected at day 72. In both sludges, about 70% of the methanol was syntrophically converted to methane and/or sulphide, via the intermediate H2/CO2. A strong competition between methanogens and sulphidogens took place in the R2 sludge with half of the methanol-COD being used by methane-producing bacteria and the other half by sulphate-reducing bacteria. Acetate was not an important intermediate for both sludges, and played a slightly more important role for the sulphate-adapted sludge (R2), sustained by the higher amount of bicarbonate produced during sulphate-reduction. The pathway study indicates that, although acetate does not represent an important intermediate, the system is susceptible to its accumulation.     

Anaerobic dechlorination of pentachlorophenol in fixed-film and upflow anaerobic sludge blanket reactors using different inocula

Longterm performance and stability of two upflow anaerobic sludge blanket (UASB) reactors inoculated with granular sludge and treating a synthetic waste water containing pentachlorophenol (PCP) and phenol were studied. A similar system consisting of two fixed-film reactors inoculated with anaerobic digested sewage sludge were further studied. One reactor in each series received glucose in addition to the phenols. Dechlorination of PCP proceeded via two different dominating pathways in the respective reactor systems, suggesting that two distinct microbial populations were present, probably originating from the different inocula. Dechlorinating activity was maintained for more than 18 months in the UASB reactors and was generally higher than in the fixed-film reactors. In the fixed-film reactors, dechlorination of PCP suddenly decreased after 15.5 months of operation compared to earlier performance. Since no operational parameters had been changed, this indicated that the enriched culture was unstable on a longterm basis. Addition of yeast extract to the medium restored activity. General process stability in both reactor systems was clearly enhanced by the addition of glucose and was superior in the UASB/granular sludge system. The better performance and the higher stability in the UASB/granular sludge reactor highlights the importance of thorough screening of inocular prior to start-up of processes treating waste waters containing xenobiotic compounds.Abbreviations PCP pentachlorophenol - TeCP tetrachlorophenol - TCP trichlorophenol - DCP dichlorophenol - UASB upflow anaerobic sludge blanket - HRT hydraulic retention time     

Granulation in anaerobic sludge bed reactors treating food industry wastes

Three parallel laboratory reactors, R1, R2 and R3, received food industry wastewater: R1 unadulterated; R2 supplemented with calcium and phosphate; R3 supplemented with ferric chloride and traces of nickel and cobalt. Reactors were packed with active granular sludge from a large scale pilot reactor treating the same wastewater. Addition of calcium and phosphate was found to be detrimental to the granule formation at naturally established reactor pH = 6·9–7·4 in R2 while iron promoted granulation in R3. Conditions of upflow velocities of 1·5–6 m h⁻¹, rapid increase of loads up to 15 kg COD m⁻³ day⁻¹ and ratios of recycle to raw waste feed of 20:1–80:1 were imposed on all reactors. The granules in R1 and R2 disintegrated, from 70–100 g liter⁻¹ VSS to a flocculant sludge at 1·5–3 g liter⁻¹. In spite of such severe washout, reactors R1 and R2 were able to maintain a steady COD removal of over 90% at a load of 10kg m⁻³ day⁻¹. R3 retained a VSS concentration around 100 g liter⁻¹ and maintained COD removal at over 95%. R3 exhibited a more stable performance and was less vulnerable to the shock treatment to which all reactors were subjected.