Compact and low-cost biosensor based on novel approach to spectroscopy of surface plasmons

A high-performance surface plasmon resonance (SPR) sensor based on a novel approach to spectroscopy of surface plasmons is reported. This approach employs a special diffraction grating structure (referred to as surface plasmon resonance coupler and disperser, SPRCD) which simultaneously couples light into a surface plasmon and disperses the diffracted light for spectral readout of SPR signal. The developed SPRCD sensor consists of a miniature cartridge integrating the diffraction grating and microfluidics and a compact optical system which simultaneously acquires data from four independent sensing channels in the cartridge. It is demonstrated that the SPRCD sensor is able to measure bulk refractive index changes as small as 3 × 10⁻⁷ RIU (refractive index units) and to detect short oligonucleotides in concentrations down to 200 pM.     

Substrate Mode-Integrated SPR Sensor

We present the design, implementation and characterisation of an integrated surface plasmon resonance (SPR) biosensor chip involving diffractive optical coupling elements avoiding the need of prism coupling. The integrated sensor chip uses the angular interrogation principle and includes two diffraction gratings and the SPR sensing zone. The theoretical design is presented as well as the fabrication process. Experimental results (response of a reference water droplet and phosphate-buffered saline/water kinetic) are presented and compared with those obtained with the classical Kretschmann prism coupling setup. We believe that this prism-free architecture is perfectly suitable for low-cost and reproducible SPR biochemical sensor chips since the sensing zone can be functionalised as any other one.     

Multi-analyte surface plasmon resonance biosensing

Surface plasmon resonance (SPR) biosensors are affinity sensing devices exploiting a special mode of electromagnetic field-surface plasmon-polariton-to detect the binding of analyte molecules from a liquid sample to biomolecular recognition elements immobilized on the surface of the sensor. In this paper, we review advances of SPR biosensor technology towards detection systems for the simultaneous detection of multiple analytes (multi-analyte detection). In addition, we report application of a recently developed multichannel SPR sensor based on spectroscopy of surface plasmons and wavelength division multiplexing of sensing channels to multi-analyte detection.     

Optimization of Multimode Fibers for Surface Plasmon Resonance Based Sensors Under Spectral and Single Wavelength Intensity Interrogation

Plasmonics - In an optical fiber based SPR sensor, a segment of metal clad silica fiber is used as the sensing element and resonant coupling occurs to the surface plasmon mode excited at the...     

Graphene/Au-Enhanced Plastic Clad Silica Fiber Optic Surface Plasmon Resonance Sensor

Owing to its large surface-to-volume ratio and good biocompatibility, graphene has been identified as a highly promising candidate as the sensing layer for fiber optic sensors. In this paper, a graphene/Au-enhanced plastic clad silica (PCS) fiber optic surface plasmon resonance (SPR) sensor is presented. A sheet of graphene is employed as a sensing layer coated around the Au film on the PCS fiber surface. The PCS fiber is chosen to overcome the shortcomings of the structured microfibers and construct a more stable and reliable device. It is demonstrated that the introduction of graphene can enhance the intensity of the confined electric field surrounding the sensing layer, which results in a stronger light-matter interaction and thereby the improved sensitivity. The sensitivity of graphene-based fiber optic SPR sensor exhibits more than two times larger than that of the conventional gold film SPR fiber optic sensor. Furthermore, the dynamic response analyses reveal that the graphene/Au fiber optic SPR sensor exhibits a fast response (5 s response time) and excellent reusability (3.5% fluctuation) to the protein biomolecules. Such a graphene/Au fiber optic SPR sensor with high sensitivity and fast response shows a great promise for the future biochemical application.     

A disposable polymer sensor chip combined with micro-fluidics and surface plasmon read-out

This paper describes a new type of disposable polymeric sensor chip based on the grating coupling of surface plasmon modes combined with a micro-fluidic channel system. A specifically designed silicon stamp with nano-structure (grating) on the micro-structures (micro-channel) was fabricated by combining a holographic method and photolithography. By using such a stamp the micro-channels, the grating coupler and the gold which was first thermally evaporated onto the stamp were transferred to the polymeric substrate successfully in one step. It is demonstrated that the grating profile in the micro-channels allowed a very efficient coupling of the laser light to the surface plasmons propagating at the bottom of the micro-channels. The transferred gold exhibits properties of a freshly cleaned surface, and the self-assembly of a functional thiol derivative (mercapto-PEG) onto the sensor chip can be monitored by surface plasmon spectroscopy. The results obtained in this sensor chip show no difference from those obtained on a regular grating-coupled SPR sensor chip.     

Design Analysis of Refractive Index Sensor with High Quality Factor Using Au-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Grating on Aluminum

We propose a surface plasmon resonance (SPR)-based refractive index sensor using gold-alumina grating over aluminum film for biosensing. Conventional SPR sensor based on gold grating exhibits broader SPR dips whereas that based on aluminum grating exhibits narrow reflection dip. A narrow reflection dip is desirable as it provides good resolution and improves the accuracy of measurement. Aluminum is less stable and generally is not preferred for an SPR-based sensor. It is more prone to being oxidized, which reduces the sensitivity and increases the width of the reflection dip of the sensor. While gold cannot provide narrow SPR reflection dips, but is used as an SPR active metal due to its more chemical stability. In order to improve the accuracy of gold grating-based sensor while taking care of oxidation problem of aluminum, in this paper, we propose a gold grating over aluminum film for SPR-based sensor and show that this configuration improves the sensitivity and the detection accuracy of the conventional sensor. Moreover, the oxidation problem is reduced to some extent as a part of aluminum is covered with gold. In order to completely avoid the oxidation of aluminum, we further propose to cover the exposed part of the aluminum with alumina and show that this configuration further improves the accuracy by reducing the width of the SPR reflection dip without affecting the sensitivity significantly. Numerical simulations show that sensitivity of proposed sensor is 270.33°/RIU with quality factor of more than 267.65 RIU^?1.     

Transmission Surface Plasmon Resonance Signal Enhancement via Growth of Gold Nanoparticles on a Gold Grating Surface

We developed a novel technique for increasing the sensitivity of transmission surface plasmon resonance (T-SPR) signals. T-SPR spectroscopy was performed by irradiating, with white light, a gold grating substrate whose surface was nanostructured by growing gold nanoparticles (AuNPs). AuNPs were grown directly on the substrate surface by alcohol reduction and their growth was observed at various stages by UV–visible spectroscopy and standard Kretschmann-type SPR spectroscopy. For comparison, normal gold film with smooth surface was examined under similar condition. The T-SPR results show a possibility of hybrid excitation of both localized and propagating surface plasmon. Significantly, T-SPR spectra of the gold grating substrate obtained during AuNP growth show stronger and narrower peaks in the range 650–800 nm. The maximum T-SPR excitation was at an incident angle of 35°. A layer-by-layer system of 5,10,15,20-tetrakis (1-methyl-4-pyridinio)porphyrin tetra(p-toluenesulfonate) molecules and sodium copper chlorophyllin molecules was used to verify the enhancement of the developed system. We believe that the AuNPs/Au grating for T-SPR devices will provide enhanced signals for detecting nanometer order materials and for high-sensitive sensor applications.     

Collection mode surface plasmon fibre sensors: a new biosensing platform

Sensors based on surface plasmon resonance (SPR) allow rapid, label-free, highly sensitive detection, and indeed this phenomenon underpins the only label-free optical biosensing technology that is available commercially. In these sensors, the existence of surface plasmons is inferred indirectly from absorption features that correspond to the coupling of light into a thin metallic film. Although SPR is not intrinsically a radiative process, when the metallic coating which support the plasmonic wave exhibits a significant surface roughness, the surface plasmon can itself couple to the local photon states, and emit light. Here we show that using silver coated optical fibres, this novel SPR transducing mechanism offers significant advantages compare to traditional reflectance based measurements such as lower dependency on the metallic thickness and higher signal to noise ratio. Furthermore, we show that more complex sensor architectures with multiple sensing regions scattered along a single optical fibre enable multiplexed detection and dynamic self referencing of the sensing signal. Moreover, this alternative approach allows to combine two different sensing technologies, SPR and fluorescence sensing within the same device, which has never been demonstrated previously. As a preliminary proof of concept of potential application, this approach has been used to demonstrate the detection of the seasonal influenza A virus.     

A miniature fiber optic surface plasmon resonance sensor for fast detection of Staphylococcal enterotoxin B

A fiber optic surface plasmon resonance (SPR) biosensor for detection of Staphylococcal enterotoxin B (SEB) is reported. The sensor is based on spectral interrogation of surface plasmons in a miniature sensing element based on a side-polished single-mode optical fiber with a thin metal overlayer. For specific detection of SEB, the SPR sensor is functionalized with a covalently crosslinked double-layer of antibodies against SEB. The SPR biosensor is demonstrated to be able to detect ng/ml concentrations of SEB in less than 10 min.     

Chemisorptions of bacterial receptors for hydrophobic amino acids and sugars on gold for biosensor applications: a surface plasmon resonance study of genetically engineered proteins

This paper demonstrates potential applications of two periplasmic receptor proteins from E. coli as sensing elements for biosensors using the surface plasmon resonance (SPR) technique. These molecules, namely the aspartate to cysteine mutant of the leucine-specific receptor (LS-D1C) and the glutamine to cysteine mutant of the D-glucose/D-galactose receptor (GGR-Q26C) proteins, are chemisorbed on a thin (approximately 40 nm) Au film in neutral K2HPO4 buffers. Using angle and time resolved SPR measurements; we show that adsorption behaviors of both proteins are dominated by diffusion-free second order Langmuir kinetics. We also show that the protein-modified Au films exhibit measurable SPR shifts upon binding to their respective target ligands. According to these SPR data, the kinetics of ligand binding for both LS-D1C and GGR-Q26C are governed by irreversible first order diffusion limited Langmuir model. The utility of the SPR technique for studying reactions of biological molecules is further illustrated in this work.     

The Effect of Molecular Adsorption on Electro-Optical Properties of Graphene-Based Sensors

Extraordinary electrical and optical features of graphene-based materials attract researchers to improve sensing center of different sensors using them. In this research, the effects of sensing molecules on electro-optical features of graphene-based sensors are modeled. The adsorption effect on the Hamiltonian of the system based on tight-binding model is explored, and also the system band structure is investigated analytically. Then, refractive index deviations based on band gap variations are discovered which are used in response modeling of a graphene-based surface plasmon resonance (SPR) sensor.

     

A surface plasmon resonance probe with a novel integrated reference sensor surface

A surface plasmon resonance (SPR) sensor probe with integrated reference surface is described. In order to fabricate the integrated reference surface, two dielectric layers with different thickness were deposited on the single gold SPR sensor surface via plasma polymerization of hexamethyldisiloxane. The working sensor surface was a 34 nm dielectric layer with immobilized bovine serum albumin (BSA) antigen and an adjacent thin 1 nm dielectric layer without BSA provided reference surface. A specific immunoreaction of anti-BSA antibody was detected after immersion of the SPR probe into sample solution. Simultaneous observation of reference and working surface response enabled determination of the immunoreaction without the need for the baseline measurement. Moreover, compensation of nonspecific adsorption could be confirmed using anti-human serum albumin antibody.     

Short order nanohole arrays in metals for highly sensitive probing of local indices of refraction as the basis for a highly multiplexed biosensor technology

A small array of subwavelength apertures patterned in a gold film on glass was characterized for use as a biosensor. It is widely believed that such arrays allow the resonance of photons with surface plasmons in the metallic film. Surface plasmon methods (and other evanescent wave methods) are extremely well suited for the measure of real time biospecific interactions. An extremely high sensitivity of 88,000%/refractive index unit was measured on an array with theoretical active area of .09 microm2. The formation of a biological monolayer was monitored. Both sensitivity and resolution were determined through measurement. The measured resolution, for a sensor with an active area of less than 1.5 microm2, is 9.4 x 10(-8) refractive index units which leads to a calculated sensitivity of 3.45E6%/refractive index unit. These values far exceed theoretical and calculated values of other grating coupled surface plasmon resonance (SPR) detectors and prism based SPR detectors. Because the active sensing area can be quite small (.025 microm2) single molecule studies are possible as well as massive multiplexing on a single chip format.     

Analysis of native proteins from biological fluids by biomolecular interaction analysis mass spectrometry (BIA/MS): exploring the limit of detection, identification of non-specific binding and detection of multi-protein complexes

Biomolecular interaction analysis mass spectrometry (BIA/MS) is a two-dimensional analytical technique that quantitatively and qualitatively detects analytes of interests. In the first dimension, surface plasmon resonance (SPR) is utilized for detection of biomolecules in their native environment. Because SPR detection is non-destructive, analyte(s) retained on the SPR-active sensor surface can be analyzed in a second dimension using matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectrometry. The qualitative nature of the MALDI-TOF MS analysis complements the quantitative character of SPR sensing and overcomes the shortcomings of the SPR detection stemming from the inability to differentiate and characterize multi-protein complexes and non-specific binding. In this work, the benefit of performing MS analysis following SPR sensing is established. Retrieval and detection of four markers present in biological fluids (cystatin C, beta-2-microglobulin, urinary protein 1 and retinol binding protein) was explored to demonstrate the effectiveness of BIA/MS in simultaneous detection of clinically related biomarkers and delineation of non-specific binding. Furthermore, the BIA/MS limit of detection at very low SPR responses was investigated. Finally, detection of in-vivo assembled protein complexes was achieved for the first time using BIA/MS.     

Colloidal Au replacement assay for highly sensitive quantification of low molecular weight analytes by surface plasmon resonance

A novel sensing method based on surface plasmon resonance (SPR) was developed for the highly sensitive quantification of low molecular weight (LMW) analytes (colloidal Au replacement assay). Gold nanoparticles (diameter = 20 nm) functionalized with lactosyl-poly(ethylene glycol) (PEG) were prepared and were specifically adsorbed onto a Ricinus communis agglutinin (RCA120)-immobilized SPR sensor chip surface. Subsequent injection of free d-galactose elicited the elution of the preadsorbed lactosyl-PEGylated gold nanoparticles in a manner proportional to the galactose concentration, achieving a substantial and quantitative analysis over a wide range of galactose concentrations (0.1-50 ppm). This method of d-galactose sensing through the substituted elution of preadsorbed nanoparticles from the sensor chip surface would be applicable for the highly sensitive SPR quantification of various LMW analytes, which are known to be difficult to detect by the conventional SPR sensing regime.     

A new surface plasmon resonance sensor for high-throughput screening applications

We report a new high-throughput surface plasmon resonance (SPR) sensor based on combination of SPR imaging with polarization contrast and a spatially patterned multilayer SPR structure. We demonstrate that this approach offers numerous advantageous features including high-contrast SPR images suitable for automated computer analysis, minimum crosstalk between neighboring sensing channels and inherent compensation for light level fluctuations. Applications of a laboratory prototype of the high-throughput SPR sensor with 108 sensing channels for refractometry and biosensing are described. In refractometric experiments, the noise-limited refractive index resolution of the system has been established to be 3 x 10(-6) refractive index unit (RIU). Experimental data on detection of human choriogonadotropin (hCG) suggest that in conjunction with monoclonal antibodies against hCG, the reported SPR imaging sensor is capable of detecting hCG at concentrations lower than 500 ng/ml.     

Self-Referencing Plasmonic Array Sensors

A self-referencing plasmonic platform is proposed and analyzed. By introducing a thin gold layer below a periodic two-dimensional nano-grating, the structure supports multiple modes including localized surface plasmon resonance (LSPR), surface plasmon resonance (SPR), and Fabry-Perot resonances. These modes get coupled to each other creating multiple Fano resonances. A coupled mode between the LSPR and SPR responses is spatially separated from the sensor surface and is not sensitive to refractive index changes in the surrounding materials or surface attachments. This mode can be used for self-referencing the measurements. In contrast, the LSPR dominant mode shifts in wavelength when the refractive index of the surrounding medium is changed. The proposed structure is easy to fabricate using conventional lithography and electron beam deposition methods. A bulk sensitivity of 429 nm/RIU is achieved. The sensor also has the ability to detect nanometer thick surface attachments on the top of the grating.

     

Multichannel,Line-Monitoring Sensing Approach Based on Long-Range Surface Plasmons

The refractive index resolution of a surface plasmon resonance (SPR) sensor has been significantly improved these years; however, higher sensing performance is always desired. In this work, we propose a line-monitoring, long-range SPR sensor whose resolution is much better than conventional SPR sensors. Also, in contrast to mono-channel detection, multichannel detection, using line-monitoring technique, can detect multiple channels concurrently. In this way, this system achieves a refractive index resolution of 4.0?×?10^??7 refractive index units and can monitor multiple molecular interactions simultaneously. Finally, a model experiment detecting the Escherichia coli bacteria has demonstrated the potential for biomedical applications of this system.     

Deposition of functionalized polymer layers in surface plasmon resonance immunosensors by in-situ polymerization in the evanescent wave field

Traditionally, the integration of sensing gel layers in surface plasmon resonance (SPR) is achieved via "bulk" methods, such as precipitation, spin-coating or in-situ polymerization onto the total surface of the sensor chip, combined with covalent attachment of the antibody or receptor to the gel surface. This is wasteful in terms of materials as the sensing only occurs at the point of resonance interrogated by the laser. By isolating the sensing materials (antibodies, enzymes, aptamers, polymers, MIPs, etc.) to this exact spot a more efficient use of these recognition elements will be achieved. Here we present a method for the in-situ formation of polymers, using the energy of the evanescent wave field on the surface of an SPR device, specifically localized at the point of interrogation. Using the photo-initiator couple of methylene blue (sensitizing dye) and sodium p-toluenesulfinate (reducing agent) we polymerized a mixture of N,N-methylene-bis-acrylamide and methacrylic acid in water at the focal point of SPR. No polymerization was seen in solution or at any other sites on the sensor surface. Varying parameters such as monomer concentration and exposure time allowed precise control over the polymer thickness (from 20-200 nm). Standard coupling with 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide and N-hydroxysuccinimide was used for the immobilization of protein G which was used to bind IgG in a typical biosensor format. This model system demonstrated the characteristic performance for this type of immunosensor, validating our deposition method.