Effect of xylan and lignin removal by batch and flowthrough pretreatment on the enzymatic digestibility of corn stover cellulose

Compared with batch systems, flowthrough and countercurrent reactors have important potential advantages for pretreating cellulosic biomass, including higher hemicellulose sugar yields, enhanced cellulose digestibility, and reduced chemical additions. Unfortunately, they suffer from high water and energy use. To better understand these trade-offs, comparative data are reported on xylan and lignin removal and enzymatic digestibility of cellulose for corn stover pretreated in batch and flowthrough reactors over a range of flow rates between 160 degrees and 220 degrees C, with water only and also with 0.1 wt% sulfuric acid. Increasing flow with just water enhanced the xylan dissolution rate, more than doubled total lignin removal, and increased cellulose digestibility. Furthermore, adding dilute sulfuric acid increased the rate of xylan removal for both batch and flowthrough systems. Interestingly, adding acid also increased the lignin removal rate with flow, but less lignin was left in solution when acid was added in batch. Although the enzymatic hydrolysis of pretreated cellulose was related to xylan removal, as others have shown, the digestibility was much better for flowthrough compared with batch systems, for the same degree of xylan removal. Cellulose digestibility for flowthrough reactors was related to lignin removal as well. These results suggest that altering lignin also affects the enzymatic digestibility of corn stover.     

Partial flow of compressed-hot water through corn stover to enhance hemicellulose sugar recovery and enzymatic digestibility of cellulose

Flowthrough pretreatment with compressed-hot water can significantly increase the removal of xylan and lignin and enhance xylose sugar yields and cellulose digestibility, especially at high flow rates. However, continuous flowthrough operations that realize these benefits suffer from a large amount of water consumption that leads to high energy requirements for pretreatment and downstream processing. Because high flow rates are particularly effective early in hemicellulose hydrolysis and less effective later, flow with compressed-hot water was applied at selected intervals, and performance was compared with that of batch and flowthrough operations for corn stover pretreated with compressed-hot water at 200 degrees C. Partial flow reduced water consumption by 60% compared with continuous flowthrough operation but still achieved higher xylose sugar yields (84-89%) compared to batch pretreatment (46.6%). In addition, corn stover cellulose pretreated by partial flow had higher enzymatic digestibility (88-90%) than batch operations (approximately 85%) at otherwise identical conditions, apparently due to much higher lignin removal for the former (40-45% vs 10-12%). Partial flow also reduced degradation, with recovery of xylose and glucose in the solids and hydrolyzate increased to 90-92% vs only about 76% for batch operation. The partial flow approach could be further improved by optimizing the operating strategy and reaction conditions, suggesting that this novel pretreatment could lead to advanced biomass pretreatment technology.     

Novel Single-step Pretreatment of Steam Explosion and Choline Chloride to De-lignify Corn Stover for Enhancing Enzymatic Edibility

It is important to develop efficient and economically feasible pretreatment methods for lignocellulosic biomass, to increase annual biomass production. A number of pretreatment methods were introduced to promote subsequent enzymatic hydrolysis of biomass for green energy processes. Pretreatment with steam explosion removes the only xylan at high severity but increases lignin content. In this study, corn stover soaked in choline chloride solution before the steam explosion is economically feasible as it reduced cost. Enzymatic hydrolysis of de-lignified corn stover is enhanced by combinatorial pretreatments of steam explosion and choline chloride. Corn stover pretreated with choline chloride at the ratio of 1:2.2 (w/w), 1.0 MPa, 184 °C, for 15 min efficiently expelled 84.7% lignin and 78.9% xylan. The residual solid comprised of 74.59% glucan and 7.51% xylan was changed to 84.2% glucose and 78.3% xylose with enzyme stacking of 10FPU/g. This single-step pretreatment had ∼ 4.5 and 6.4 times higher glucose yield than SE-pretreated and untreated corn stover, respectively. Furthermore, SEM, XRD and FTIR indicated the porosity, crystalline changes, methoxy bond-cleavage respectively due to the lignin and hemicellulose expulsion. Thus, the released acetic acid during this process introduced this novel strategy, which significantly builds the viability of biomass in short pretreatment time.     

Effect of hemicellulose and lignin removal on enzymatic hydrolysis of steam pretreated corn stover

Ethanol can be produced from lignocellulosic biomass using steam pretreatment followed by enzymatic hydrolysis and fermentation. The sugar yields, from both hemicellulose and cellulose are critical parameters for an economically-feasible ethanol production process. This study shows that a near-theoretical glucose yield (96-104%) from acid-catalysed steam pretreated corn stover can be obtained if xylanases are used to supplement cellulases during hydrolysis. Xylanases hydrolyse residual hemicellulose, thereby improving the access of enzymes to cellulose. Under these conditions, xylose yields reached 70-74%. When pre-treatment severity was reduced by using autocatalysis instead of acid-catalysed steam pretreatment, xylose yields were increased to 80-86%. Partial delignification of pretreated material was also evaluated as a way to increase the overall sugar yield. The overall glucose yield increased slightly due to delignification but the overall xylose yield decreased due to hemicellulose loss in the delignification step. The data also demonstrate that steam pretreatment is a robust process: corn stover from Europe and North America showed only minor differences in behaviour.     

Enhanced enzymatic hydrolysis and structural features of corn stover by FeCl3 pretreatment

Corn stover was pretreated with FeCl₃ to remove almost all of the hemicellulose present and then hydrolyzed with cellulase and β-glucosidase to produce glucose. Enzymatic hydrolysis of corn stover that had been pretreated with FeCl₃ at 160 °C for 20 min resulted in an optimum yield of 98.0%. This yield was significantly higher than that of untreated corn stover (22.8%). FeCl₃ pretreatment apparently damaged the surface of corn stover and significantly increased the enzymatic digestibility, as evidenced by SEM and XRD analysis data. FTIR analysis indicated that FeCl₃ pretreatment could disrupt almost all the ether linkages and some ester linkages between lignin and carbohydrates but had no effect on delignification. The FeCl₃ pretreatment technique, as a novel pretreatment method, enhances enzymatic hydrolysis of lignocellulosic biomass by destructing chemical composition and altering structural features.     

Effect of structural features on enzyme digestibility of corn stover

Corn stover was pretreated with excess calcium hydroxide (0.5 g Ca(OH)2/g raw biomass) in non-oxidative and oxidative conditions at 25, 35, 45, and 55 degrees C. The enzymatic digestibility of lime-treated corn stover was affected by the change of structural features (acetylation, lignification, and crystallization) resulting from the treatment. Extensive delignification required oxidative treatment and additional consumption of lime (up to 0.17 g Ca(OH)2/g biomass). Deacetylation reached a plateau within 1 week and there were no significant differences between non-oxidative and oxidative conditions at 55 degrees C; both conditions removed approximately 90% of the acetyl groups in 1 week at all temperatures studied. Delignification highly depended on temperature and the presence of oxygen. Lignin and hemicellulose were selectively removed (or solubilized), but cellulose was not affected by lime pretreatment in mild temperatures (25-55 degrees C), even though corn stover was contacted with alkali for a long time, 16 weeks. The degree of crystallinity slightly increased from 43% to 60% with delignification because amorphous components (lignin, hemicellulose) were removed. However, the increased crystallinity did not negatively affect the 3-d sugar yield of enzymatic hydrolysis. Oxidative lime pretreatment lowered the acetyl and lignin contents to obtain high digestibility, regardless of crystallinity. The non-linear models for 3-d hydrolysis yields of glucan (Y(g)), xylan (Y(x)), and holocellulose (Y(gx)) were empirically established as a function of the residual lignin (L) for the corn stover pretreated with lime and air.     

Integrated analysis of hydrothermal flowthroughpretreatment

ABSTRACT: BACKGROUND: The impact of hydrothermal flowthrough (FT) pretreatment severity on pretreatment and solubilization performance metrics was evaluated for three milled feedstocks (corn stover, bagasse, and poplar) and two conversion systems (simultaneous saccharification and fermentation using yeast and fungal cellulase, and fermentation by Clostridium thermocellum). RESULTS: Compared to batch pretreatment, FT pretreatment consistently resulted in higher xylan recovery, higher removal of non-carbohydrate components and higher glucan solubilization by simultaneous saccharification and fermentation (SSF). Xylan recovery was above 90% for FT pretreatment below 4.1 severity but decreased at higher severities, particularly for bagasse. Removal of non-carbohydrate components during FT pretreatment increased from 65% at low severity to 80% at high severity for corn stover, and from 40% to 70% for bagasse and poplar. Solids obtained by FT pretreatment were amenable to high conversion for all of the feedstocks and conversion systems examined. The optimal time and temperature for FT pretreatment on poplar were found to be 16 minutes and 210 oC. At these conditions, SSF glucan conversion was about 85%, 94% of the xylan was removed, and 62% of the non carbohydrate mass was solubilized. Solubilization of FT-pretreated poplar was compared for C. thermocellum fermentation (10% inoculum), and for yeast-fungal cellulase SSF (5% inoculum, cellulase loading of 5 and 10 FPU/g glucan supplemented with beta-glucosidase at 15 and 30 U/g glucan). Under the conditions tested, which featured low solids concentration, C. thermocellum fermentation achieved faster rates and more complete conversion of FT-pretreated poplar than did SSF. Compared to SSF, solubilization by C. thermocellum was 30% higher after 4 days, and was over twice as fast on ball-milled FT-pretreated poplar. CONCLUSIONS: Xylan removal trends were similar between feedstocks whereas glucan conversion trends were significantly different, suggesting that factors in addition to xylan removal impact amenability of glucan to enzymatic attack. Corn stover exhibited higher hydrolysis yields than bagasse or poplar, which could be due to higher removal of non-carbohydrate components. Xylan in bagasse is more easily degraded than xylan in corn stover and poplar. Conversion of FT-pretreated substrates at low concentration was faster and more complete for C.thermocellum than for SSF.     

The pretreatment of corn stover with Gloeophyllum trabeum KU-41 for enzymatic hydrolysis

Background

Pretreatment is an essential step in the enzymatic hydrolysis of biomass for bio-ethanol production. The dominant concern in this step is how to decrease the high cost of pretreatment while achieving a high sugar yield. Fungal pretreatment of biomass was previously reported to be effective, with the advantage of having a low energy requirement and requiring no application of additional chemicals. In this work, Gloeophyllum trabeum KU-41 was chosen for corn stover pretreatment through screening with 40 strains of wood-rot fungi. The objective of the current work is to find out which characteristics of corn stover pretreated with G. trabeum KU-41 determine the pretreatment method to be successful and worthwhile to apply. This will be done by determining the lignin content, structural carbohydrate, cellulose crystallinity, initial adsorption capacity of cellulase and specific surface area of pretreated corn stover.

Results

The content of xylan in pretreated corn stover was decreased by 43% in comparison to the untreated corn stover. The initial cellulase adsorption capacity and the specific surface area of corn stover pretreated with G. trabeum were increased by 7.0- and 2.5-fold, respectively. Also there was little increase in the cellulose crystallinity of pretreated corn stover.

Conclusion

G. trabeum has an efficient degradation system, and the results indicated that the conversion of cellulose to glucose increases as the accessibility of cellulose increases due to the partial removal of xylan and the structure breakage of the cell wall. This pretreatment method can be further explored as an alternative to the thermochemical pretreatment method.     

Comparison of microwaves to fluidized sand baths for heating tubular reactors for hydrothermal and dilute acid batch pretreatment of corn stover

Heating of batch tubular reactors with fluidized sand baths and with microwaves resulted in distinctive sugar yield profiles from pretreatment and subsequent enzymatic hydrolysis of corn stover at the same time, temperature, and dilute sulfuric acid concentration combinations and hydrothermal pretreatment conditions. Microwave heated pretreatment led to faster xylan, lignin, and acetyl removal as well as earlier xylan degradation than sand baths, but maximum sugar recoveries were similar. Solid state CP/MAS NMR revealed that microwave heating was more effective in altering cellulose structural features especially in breakdown of amorphous regions of corn stover than sand bath heating. Enzymatic hydrolysis of pretreated corn stover was improved by microwave heating compared to sand bath heating. Mechanisms were proposed to explain the differences in results for the two systems and provide new insights into pretreatment that can help advance this technology.     

Redistribution of xylan in maize cell walls during dilute acid pretreatment

Developing processes for the conversion of biomass for use in transportation fuels production is becoming a critically important economic and engineering challenge. Dilute acid pretreatment is a promising technology for increasing the enzymatic digestibility of lignocellulosic biomass. However, a deeper understanding of the pretreatability of biomass is needed so that the rate of formation and yields of sugars can be increased. Xylan is an important hemicellulosic component of the plant cell wall and acts as a barrier to cellulose, essentially blocking cellulase action. To better understand xylan hydrolysis in corn stover, we have studied changes in the distribution of xylan caused by dilute acid pretreatment using correlative microscopy. A dramatic loss of xylan antibody signal from the center of the cell wall and an increase or retention of xylan at the plasma membrane interface and middle lamella of the cell were observed by confocal laser scanning microscopy (CLSM). We also observed a reduction in xylan fluorescence signal by CLSM that is generally consistent with the decrease in xylan content measured experimentally in the bulk sample, however, the compartmentalization of this xylan retention was not anticipated. Biotechnol. Bioeng. 2009;102: 1537–1543. © 2008 Wiley Periodicals, Inc.     

Benefits from tween during enzymic hydrolysis of corn stover

Corn stover is a potential substrate for fermentation processes. Previous work with corn stover demonstrated that lime pretreatment rendered it digestible by cellulase; however, high sugar yields required very high enzyme loadings. Because cellulase is a significant cost in biomass conversion processes, the present study focused on improving the enzyme efficiency using Tween 20 and Tween 80; Tween 20 is slightly more effective than Tween 80. The recommended pretreatment conditions for the biomass remained unchanged regardless of whether Tween was added during the hydrolysis. The recommended Tween loading was 0.15 g Tween/g dry biomass. (The critical relationship was the Tween loading on the biomass, not the Tween concentration in solution.) The 72-h enzymic conversion of pretreated corn stover using 5 FPU cellulase/g dry biomass at 50 degrees C with Tween 20 as part of the medium was 0.85 g/g for cellulose, 0.66 g/g for xylan, and 0.75 for total polysaccharide; addition of Tween improved the cellulose, xylan, and total polysaccharide conversions by 42, 40, and 42%, respectively. Kinetic analyses showed that Tween improved the enzymic absorption constants, which increased the effective hydrolysis rate compared to hydrolysis without Tween. Furthermore, Tween prevented thermal deactivation of the enzymes, which allows for the kinetic advantage of higher temperature hydrolysis. Ultimate digestion studies showed higher conversions for samples containing Tween, indicating a substrate effect. It appears that Tween improves corn stover hydrolysis through three effects: enzyme stabilizer, lignocellulose disrupter, and enzyme effector. Copyright 1998 John Wiley & Sons, Inc.     

Evaluation of the xylan breakdown potential of eight mesophilic endoxylanases

In biomass degradation using simultaneous saccharification and fermentation (SSF), there is a need for efficient biomass degrading enzymes that can work at lower temperatures suitable for yeast fermentation. As xylan is an important lignocellulosic biomass constituent, this study aimed at investigating the possible differences in xylan breakdown potential of endoxylanases using eight different endoxylanases at conditions relevant for SSF. Both solubilising and degrading capacities of the endoxylanases were investigated using water-insoluble and water-soluble oat spelt xylan as model substrates for biomass xylan. Results showed that selecting for combinations of endoxylanases that are efficient at solubilising xylan on the one hand and degrading it to large extent on the other hand, coupled to high specific activities, seems the best option for complete xylan breakdown in lignocellulosic biomass conversion using SSF.     

Degradation of lignocellulose by extracellular enzymes produced by Thermomonospora fusca BD25

Degradation products from the addition of extracellular enzymes from Thermomonospora fusca BD25 to ball-milled wheat straw, oat spelt xylan and solubilised kraft pulps were characterised by HPLC and TLC. Overall, a high percentage hydrolysis of oat spelt xylan (28.9%) occurred after 26 h incubation. However, the rates of hydrolysis of ball-milled wheat straw and kraft pulp were approximately 4-6-fold less than xylan hydrolysis, although the total percentage hydrolysis of available substrate was similar (22.2% and 25.9% respectively). Incubation of kraft pulp and ball-milled wheat straw by crude extracellular enzymes of T. fusca BD25 resulted in the detection of aromatic compounds at concentrations of 0.6 microg ml(-1) and 8.7 microg ml(-1), respectively. Hydrolysis of oat spelt xylan by T. fusca BD25 extracellular enzymes yielded a mixture of xylose, xylotriose and putative substituted-xylotriose, while the products of ball-milled wheat straw hydrolysis were xylose, glucose and a small oligomer present in the digest. The results highlight the ability of culture supernatant from T. fusca to release both simple sugars and aromatic compounds from lignocellulosic substrates and suggest a role for this organism in the biobleaching of pulp.     

Hemicellulose bioconversion

Various agricultural residues, such as corn fiber, corn stover, wheat straw, rice straw, and sugarcane bagasse, contain about 20–40% hemicellulose, the second most abundant polysaccharide in nature. The conversion of hemicellulose to fuels and chemicals is problematic. In this paper, various pretreatment options as well as enzymatic saccharification of lignocellulosic biomass to fermentable sugars is reviewed. Our research dealing with the pretreatment and enzymatic saccharification of corn fiber and development of novel and improved enzymes such as endo-xylanase, β-xylosidase, and α-l-arabinofuranosidase for hemicellulose bioconversion is described. The barriers, progress, and prospects of developing an environmentally benign bioprocess for large-scale conversion of hemicellulose to fuel ethanol, xylitol, 2,3-butanediol, and other value-added fermentation products are highlighted.     

Fungal metabolism of fermentation inhibitors present in corn stover dilute acid hydrolysate

Use of agricultural residues for ethanol production requires pretreatment of the material to facilitate release of sugars. Physical–chemical pretreatment of lignocellulosic biomass can, however, give rise to side-products that may be toxic to fermenting microorganisms and hinder utilization of sugars obtained from biomass. Potentially problematic compounds include furan aldehydes formed by degradation of sugars, organic acids released from hemicellulose side-groups, and aldehydes and phenolics released from lignin. A fungal isolate, Coniochaeta ligniaria NRRL30616, metabolizes furfural and 5-hydroxymethylfurfural (HMF) as well as aromatic and aliphatic acids and aldehydes. NRRL30616 grew in corn stover dilute-acid hydrolysate, and converted furfural to both furfuryl alcohol and furoic acid. Hydrolysate was inoculated with NRRL30616, and the fate of pretreatment side-products was followed in a time-course study. A number of aromatic and aliphatic acids, aldehydes, and phenolic compounds were quantitated by analytical extraction of corn stover hydrolysate, followed by HPLC–UV–MS/MS analysis. Compounds representing all of the classes of inhibitory side-products were removed during the course of fungal growth. Biological abatement of hydrolysates using C. ligniaria improved xylose utilization in subsequent ethanol fermentations.     

Influence of xylan on the enzymatic hydrolysis of steam‐pretreated corn stover and hybrid poplar

The focus of this study was to alter the xylan content of corn stover and poplar using SO₂‐catalyzed steam pretreatment to determine the effect on subsequent hydrolysis by commercial cellulase preparations supplemented with or without xylanases. Steam pretreated solids with xylan contents ranging from ～1 to 19% (w/w) were produced. Higher xylan contents and improved hemicellulose recoveries were obtained with solids pretreated at lower severities or without SO₂‐addition prior to pretreatment. The pretreated solids with low xylan content (<4% (w/w)) were characterized by fast and complete cellulose to glucose conversion when utilizing cellulases. Commercial cellulases required xylanase supplementation for effective hydrolysis of pretreated substrates containing higher amounts of xylan. It was apparent that the xylan content influenced both the enzyme requirements for hydrolysis and the recovery of sugars during the pretreatment process. © 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

Fractionation of corn stover by hot-water and aqueous ammonia treatment

The efficiency of biomass utilization can be significantly improved by fractionation of biomass. A two-stage percolation process was investigated for pretreatment and fractionation of corn stover. The two-stage process is composed of hot water treatment followed by treatment with aqueous ammonia, both applied in a flow-through (percolation) reactor. The first stage processing is intended for hemicellulose removal whereas the second stage is intended for delignification. The pretreated material was nearly pure cellulose and both reagents are cheap and environmentally friendly. The conditions that achieve satisfactory level of biomass fractionation and acceptable enzymatic hydrolysis were identified in terms of reaction temperature, flow rate (retention time) and reaction time for each stage. With proper operation of two-stage treatment, fractionation of biomass was achieved to the extent that the xylan fraction is hydrolyzed with 92-95% conversion, and recovered with 83-86% yields; and the lignin removal is 75-81%. The remaining solid after two-stage treatment contained 78-85% cellulose. The two-stage treatments enhanced the enzymatic digestibility to 90-96% with 60 FPU/g of glucan, and 87-89% with 15 FPU/g of glucan. In two-stage treatment, the composition and digestibility data indicate that the lignin content in the biomass is one of the major factors controlling the enzymatic digestibility.     

Development and validation of a kinetic model for enzymatic saccharification of lignocellulosic biomass

A multireaction kinetic model was developed for closed-system enzymatic hydrolysis of lignocellulosic biomass such as corn stover. Three hydrolysis reactions were modeled, two heterogeneous reactions for cellulose breakdown to cellobiose and glucose and one homogeneous reaction for hydrolyzing cellobiose to glucose. Cellulase adsorption onto pretreated lignocellulose was modeled via a Langmuir-type isotherm. The sugar products of cellulose hydrolysis, cellobiose and glucose, as well as xylose, the dominant sugar prevalent in most hemicellulose hydrolyzates, were assumed to competitively inhibit the enzymatic hydrolysis reactions. Model parameters were estimated from experimental data generated using dilute acid pretreated corn stover as the substrate. The model performed well in predicting cellulose hydrolysis trends at experimental conditions both inside and outside the design space used for parameter estimation and can be used for in silico process optimization.     

Lime pretreatment and enzymatic hydrolysis of corn stover

Corn stover was pretreated with an excess of calcium hydroxide (0.5 g Ca(OH)2/g raw biomass) in non-oxidative and oxidative conditions at 25, 35, 45, and 55 degrees C. The optimal condition is 55 degrees C for 4 weeks with aeration. Glucan (91.3%) and xylan (51.8%) were converted to glucose and xylose respectively, when the treated corn stover was enzymatically hydrolyzed with 15 FPU/g cellulose. Only 0.073 g Ca(OH)2 was consumed per g of raw corn stover. Of the initial lignin, 87.5% was maximally removed. Almost all acetyl groups were removed. After 4 weeks at 55 degrees C with aeration, some cellulose and hemicellulose were solubilized as monomers and oligomers in the pretreatment liquor. When considering the dissolved fragments of glucan and xylan in the pretreatment liquor, the overall yields of glucose and xylose were 93.2% and 79.5% at 15 FPU/g cellulose. The pretreatment liquor has no inhibitory effect on ethanol fermentation.     

Facile pretreatment of lignocellulosic biomass at high loadings in room temperature ionic liquids

Ionic liquids (ILs) have emerged as attractive solvents for lignocellulosic biomass pretreatment in the production of biofuels and chemical feedstocks. However, the high cost of ILs is a key deterrent to their practical application. Here, we show that acetate based ILs are effective in dramatically reducing the recalcitrance of corn stover toward enzymatic polysaccharide hydrolysis even at loadings of biomass as high as 50% by weight. Under these conditions, the IL serves more as a pretreatment additive rather than a true solvent. Pretreatment of corn stover with 1‐ethyl‐3‐methylimidizolium acetate ([Emim] [OAc]) at 125 ± 5°C for 1 h resulted in a dramatic reduction of cellulose crystallinity (up to 52%) and extraction of lignin (up to 44%). Enzymatic hydrolysis of the IL‐treated biomass was performed with a common commercial cellulase/xylanase from Trichoderma reesei and a commercial β‐glucosidase, and resulted in fermentable sugar yields of ～80% for glucose and ～50% for xylose at corn stover loadings up to 33% (w/w) and 55% and 34% for glucose and xylose, respectively, at 50% (w/w) biomass loading. Similar results were observed for the IL‐facilitated pretreatment of switchgrass, poplar, and the highly recalcitrant hardwood, maple. At 4.8% (w/w) corn stover, [Emim][OAc] can be readily reused up to 10 times without removal of extracted components, such as lignin, with no effect on subsequent fermentable sugar yields. A significant reduction in the amount of IL combined with facile recycling has the potential to enable ILs to be used in large‐scale biomass pretreatment. Biotechnol. Bioeng. 2011;108: 2865–2875. © 2011 Wiley Periodicals, Inc.