Statistical evaluation and modeling of cheap substrate-based cultivation medium of Chlorella vulgaris to enhance microalgae lipid as new potential feedstock for biolubricant

Chlorella vulgaris (C. vulgaris) microalga was investigated as a new potential feedstock for the production of biodegradable lubricant. In order to enhance microalgae lipid for biolubricant production, mixotrophic growth of C. vulgaris was optimized using statistical analysis of Plackett–Burman (P-B) and response surface methodology (RSM). A cheap substrate-based medium of molasses and corn steep liquor (CSL) was used instead of expensive mineral salts to reduce the total cost of microalgae production. The effects of molasses and CSL concentration (cheap substrates) and light intensity on the growth of microalgae and their lipid content were analyzed and modeled. Designed models by RSM showed good compatibility with a 95% confidence level when compared to the cultivation system. According to the models, optimal cultivation conditions were obtained with biomass productivity of 0.123 g L^?1 day^?1 and lipid dry weight of 0.64 g L^?1 as 35% of dry weight of C. vulgaris. The extracted microalgae lipid presented useful fatty acid for biolubricant production with viscosities of 42.00 cSt at 40°C and 8.500 cSt at 100°C, viscosity index of 185, flash point of 185°C, and pour point of ?6°C. These properties showed that microalgae lipid could be used as potential feedstock for biolubricant production.     

Biological CO<Subscript>2</Subscript> fixation using C<Emphasis Type="Italic">hlorella vulgaris</Emphasis> and its thermal characteristics through thermogravimetric analysis

The present research is focused on cultivation of microalgae strain Chlorella vulgaris for bio-fixation of CO₂ coupled with biomass production. In this regard, a single semi-batch vertical tubular photobioreactor and four similar photobioreactors in series have been employed. The concentration of CO₂ in the feed stream was varied from 2 to 12 % (v/v) by adjusting CO₂ to air ratio. The amount of CO₂ capture and algae growth were monitored by measuring decrease of CO₂ concentration in the gas phase, microalgal cell density, and algal biomass production rate. The results show that 4 % CO₂ gives maximum amount of biomass (0.9 g L^?1) and productivity (0.118 g L^?1 day^?1) of C. vulgaris in a single reactor. In series reactors, average productivity per reactor found to be 0.078 g L^?1 day^?1. The maximum CO₂ uptake for single reactor also found with 4 % CO_2, and it is around 0.2 g L^?1 day^?1. In series reactors, average CO₂ uptake is 0.13 g L^?1 day^?1 per reactor. TOC analysis shows that the carbon content of the produced biomass is around 40.67 % of total weight. The thermochemical characteristics of the cultivated C. vulgaris samples were analyzed in the presence of air. All samples burn above 200 °C and the combustion rate become faster at around 600 °C. Almost 98 wt% of the produced biomass is combustible in this range.     

Biomass,Lipid and Fatty Acid Production in Large-Scale Cultures of the Marine Macroalga Derbesia tenuissima (Chlorophyta)

Biomass productivity was quantified for the marine macroalga Derbesia tenuissima cultivated outdoors at seven stocking densities from 0.25 to 8 g L^?1 for 5 weeks. Total lipids and fatty acid quantity and quality was measured from samples that were freeze-dried, dried by oven (75 °C), food dehydrator (60 °C), or outdoor in the sun (40 °C) or shade (38 °C). Stocking densities of 0.25 to 2 g L^?1 yielded the highest biomass productivities (>20 g dry weight m^?2 day^?1) with no effect on total lipid quantity (11 %), or fatty acid quantity (5.3 %) or quality at any density tested. However, there was an interactive effect of stocking density and drying technique, with a decrease of up to 40 % in polyunsaturated fatty acids in sun-dried compared to freeze-dried biomass. Notably, while fatty acid and biomass productivity may be inseparable in macroalgae, cultivation conditions have a significant carryover effect in the post-harvest delivery of high-quality bio-oils.     

Magnetophoretic harvesting of freshwater microalgae using polypyrrole/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocomposite and its reusability

A magnetophoretic harvesting agent, a polypyrrole/Fe₃O₄ magnetic nanocomposite, is proposed as a cost and energy efficient alternative to recover biomass of the microalgae Botryococcus braunii, Chlorella protothecoides, and Chlorella vulgaris from their culture media. The maximal recovery efficiency reached almost 99 % for B. braunii, 92.4 % for C. protothecoides, and 90.8 % for C. vulgaris. The maximum adsorption capacity (Q ₀) of the magnetic nanocomposite for B. braunii (63.49 mg dry biomass mg^?1 PPy/Fe₃O₄) was higher than that for C. protothecoides (43.91 mg dry biomass mg^?1 PPy/Fe₃O₄) and C. vulgaris (39.98 mg dry biomass mg^?1 PPy/Fe₃O₄). The highest harvesting efficiency for all the studied microalgae were at pH 10.0, and measurement of zeta-potential confirmed that the flocculation was induced by charge neutralization. This study showed that polypyrrole/Fe₃O₄ can be a promising flocculant due to its high efficacy, low dose requirements, short settling time, its integrity with cells, and with great potential for saving energy because of its recyclability.     

Wastewater treatment and biofuel production through attached culture of <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> in a porous substratum biofilm reactor

The feasibility of attached culture Chlorella vulgaris in a porous substratum biofilm reactor (PSBR) for simultaneous wastewater treatment and biofuel production was investigated. The characteristics, including algal biofilm growth, lipid yield, nutrient removal, and energy efficiency of the outdoor cultures, were investigated under the influence of both inoculum densities and the percent submerged area. A maximum biofilm productivity of 57.87 g m^?2 d^?1 with 81.9 % adhesion was achieved under optimal conditions (inoculum density of 18 g m^?2 and the percent submerged area of 5.7 %). The lipid content and lipid yield were 38.56 % and 27.25 g m^?2 d^?1, respectively. Meanwhile, the algae removed 99.95 % ammonia, 96.05 % total nitrogen (TN), and 99.83 % total phosphorus (TP). Further, the energy life cycle for the PSBR was analyzed. The biomass productivity per unit irradiance was up to 4.6 g MJ^?1 (photosynthetic efficiency of 10.65 %). The PSBR was considered to be economically feasible due to the net energy ratio of 1.3 (>1).     

Comparison of biomass production and total lipid content of freshwater green microalgae cultivated under various culture conditions

The growth and total lipid content of four green microalgae (Chlorella sp., Chlorella vulgaris CCAP211/11B, Botryococcus braunii FC124 and Scenedesmus obliquus R8) were investigated under different culture conditions. Among the various carbon sources tested, glucose produced the largest biomass or microalgae grown heterotrophically. It was found that 1 % (w/v) glucose was actively utilized by Chlorella sp., C. vulgaris CCAP211/11B and B. braunii FC124, whereas S. obliquus R8 preferred 2 % (w/v) glucose. No significant difference in biomass production was noted between heterotrophic and mixotrophic (heterotrophic with light illumination/exposure) growth conditions, however, less production was observed for autotrophic cultivation. Total lipid content in cells increased by approximately two-fold under mixotrophic cultivation with respect to heterotrophic and autotrophic cultivation. In addition, light intensity had an impact on microalgal growth and total lipid content. The highest total lipid content was observed at 100 μmol m^?2s^?1 for Chlorella sp. (22.5 %) and S. obliquus R8 (23.7 %) and 80 μmol m^?2s^?1 for C. vulgaris CCAP211/11B (20.1 %) and B. braunii FC124 (34.9 %).     

The effect of nitrogen limitation on lipid productivity and cell composition in Chlorella vulgaris

Chlorella vulgaris accumulates lipid under nitrogen limitation, but at the expense of biomass productivity. Due to this tradeoff, improved lipid productivity may be compromised, despite higher lipid content. To determine the optimal degree of nitrogen limitation for lipid productivity, batch cultures of C. vulgaris were grown at different nitrate concentrations. The growth rate, lipid content, lipid productivity and biochemical and elemental composition of the cultures were monitored for 20 days. A starting nitrate concentration of 170 mg L^?1 provided the optimal tradeoff between biomass and lipid production under the experimental conditions. Volumetric lipid yield (in milligram lipid per liter algal culture) was more than double that under nitrogen-replete conditions. Interpolation of the data indicated that the highest volumetric lipid concentration and lipid productivity would occur at nitrate concentrations of 305 and 241 mg L^?1, respectively. There was a strong correlation between the nitrogen content of the cells and the pigment, protein and lipid content, as well as biomass and lipid productivity. Knowledge of the relationships between cell nitrogen content, growth, and cell composition assists in the prediction of the nitrogen regime required for optimal productivity in batch or continuous culture. In addition to enhancing lipid productivity, nitrogen limitation improves the lipid profile for biodiesel production and reduces the requirement for nitrogen fertilizers, resulting in cost and energy savings and a reduction in the environmental burden of the process.     

Cultivation of <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> with swine wastewater and potential for algal biodiesel production

In this study, an alga-based simultaneous process of treating swine wastewater (SWW) and producing biodiesel was explored. Chlorella vulgaris (UTEX-265) was employed as a model species, and a SWW-based medium was prepared by dilution with tap water. Chlorella vulgaris grew well in the SWW-based medium, and at optimum dilution ratios, it exceeded the conventional culture medium in terms of biomass concentration and productivity. In eightfold diluted SWW, which supported the maximum growth, biomass productivity was 0.247 g L^?1 day^?1, while the productivity was merely 0.165 g L^?1 day^?1 in standard tris-acetate-phosphorous (TAP) algal medium. In addition, fatty acid methyl ester (FAME) productivity was greater in the SWW-based medium (0.067 versus 0.058 g L^?1 day^?1). This enhanced productivity resulted in more than 95 % removal of both nitrogen and phosphorous. All these show that C. vulgaris cultivation is indeed possible in a nutrient-rich wastewater with appropriate dilution, and in so doing, the wastewater can effectively be treated.     

Lipid production and composition of fatty acids in Chlorella vulgaris cultured using different methods: photoautotrophic,heterotrophic, and pure and mixed conditions

This study investigated the biomass, lipid production, fatty acid content, and other nutrients present in microorganisms by using four culture methods: (1) photoautotrophic pure Chlorella vulgaris cultures (PP); (2) heterotrophic pure C. vulgaris cultures (PH); (3) mixed cultures of Rhodotorula glutinis and C. vulgaris under photoautotrophic conditions (MP); and (4) heterotrophic mixed cultures (MH). The microorganisms in MP culture showed the optimum growth condition and lipid production. Among the cultures, MP yielded the highest number of cells and biomass (5.9?×?10⁵ cells/mL and 0.523 g/L, respectively). Furthermore, lipid production in MP culture was 114.22 mg/L, which is 136 % higher than that in MH culture (48.22 mg/L). Considering the higher contents of palmitic acid (C16:0) at 24.65 %, oleic acid (C18:1) at 56.34 %, and protein at 42.39 g/100 g in the MP culture than in other cultures, we proposed that MP could be used effectively to support the growth of microorganisms. This method could also be used as a potential approach for biodiesel production.     

Attached culture of Nannochloropsis oculata for lipid production

The influences of urea, nitrate and glycine with four concentration levels on attached culture of Nannochloropsis oculata were investigated. The organic nitrogen source glycine was effective on improving not only adhesion biomass productivity but also adhesion rate. The maximum adhesion biomass productivity of 15.76 ± 0.52 g m^?2 day^?1 with adhesion rate of 76.67 ± 0.42 % was achieved with 18 mM glycine. To increase the lipid production, three lipid enhancing strategies were conducted afterwards, including nitrogen starvation, high light, and the combination of nitrogen starvation and high light. In nitrogen starvation situation, although the lipid content was greatly increased, the adhesion biomass productivity dropped probably due to the low cell viability. Increasing light intensity was effective on enhancing both adhesion biomass productivity and lipid content. The results indicated that nitrogen starvation was effective on improving both lipid content and adhesion rate when high light was applied. The maximum lipid yield of 4.32 ± 0.14 g m^?2 day^?1 with adhesion biomass productivity of 21.32 ± 0.65 g m^?2 day^?1, adhesion rate of 86.81 ± 0.10 % and lipid content of 20.24 ± 0.06 % was achieved with the combination strategy.     

Investigation of mixotrophic,heterotrophic, and autotrophic growth of Chlorella vulgaris under agricultural waste medium

Growth of Chlorella vulgaris and its lipid production were investigated under autotrophic, heterotrophic, and mixotrophic conditions. Cheap agricultural waste molasses and corn steep liquor from industries were used as carbon and nitrogen sources, respectively. Chlorella vulgaris grew remarkably under this agricultural waste medium, which resulted in a reduction in the final cost of the biodiesel production. Maximum dry weight of 2.62 g L^?1 was obtained in mixotrophic growth with the highest lipid concentration of 0.86 g L^?1. These biomass and lipid concentrations were, respectively, 140% and 170% higher than autotrophic growth and 300% and 1200% higher than heterotrophic growth. In mixotrophic growth, independent or simultaneous occurrence of autotrophic and heterotrophic metabolisms was investigated. The growth of the microalgae was observed to take place first heterotrophically to a minimum substrate concentration with a little fraction in growth under autotrophic metabolism, and then the cells grew more autotrophically. It was found that mixotrophic growth was not a simple combination of heterotrophic and autotrophic growth.     

Growth and palmitoleic acid accumulation of filamentous oleaginous microalgae <Emphasis Type="Italic">Tribonema minus</Emphasis> at varying temperatures and light regimes

Palmitoleic acid (C16:1Δ9), contributes greatly to human health, industrial chemicals and biodiesel. The filamentous oleaginous microalgae Tribonema sp. has been identified as a highly efficient producer of palmitoleic acid. Temperature and light regime were adapted to regulate the palmitoleic acid content in this study. Strain T. minus was able to grow well at all the tested temperatures, even at 5 °C. The optimum temperature for palmitoleic acid accumulation (54.25 % of total fatty acid) was 25 °C. Moreover, both light intensity and photoperiod affect the growth, lipid content and fatty acid files of T. minus. The culture exposed to 240 μmol photons m^?2 s^?1 with a photoperiod of 24:0 showed the highest biomass (6.87 g L^?1) and biggest lipid content (61.27 % of dry weight), whereas the most amount of palmitoleic acid (50.47 % of total fatty acid) was detected at 120 μmol photons m^?2 s^?1. These findings make tangible contributions to culture T. minus for commercial production of lipid or palmitoleic acid.     

Optimisation of biomass and lipid production by adjusting the interspecific competition mode of Dunaliella salina and Nannochloropsis gaditana in mixed culture

The high cost of algal cultivation has been a barrier associated with the commercialisation of algal biodiesel. Therefore, this study aimed to enhance lipid production by optimising the nutrient supply to benefit the coexistence of Dunaliella salina and Nannochloropsis gaditana. The effects on biomass and lipid production of using different proportions of D. salina and N. gaditana, urea and NaHCO₃ were optimised by response surface method with a 17-run Box–Behnken design. The optimal conditions for the algal growth are 58 % of D. salina in the mixture at OD₆₈₀, 150 μL day^?1 urea (0.0044 g day^?1) and no addition of NaHCO₃. The biomass concentration and lipid production reached 1.00 and 0.383 g L^?1, respectively, which are exceeded by the amount before optimisation, indicating the efficiency of the model obtained by response surface method.     

Regulation of carbon metabolic fluxes in response to CO<Subscript>2</Subscript> supplementation in phototrophic <Emphasis Type="Italic">Chlorella vulgaris</Emphasis>: a cytomic and biochemical study

As one of the promising species of microalgae for biofuel production, Chlorella vulgaris CS-42 was cultivated phototrophically in two cylindrical photobioreactors with aeration of 5 % (v/v) CO₂ or air for 13 days to evaluate the effects of CO₂ supplementation on biomass, CO₂ fixation performance, and biochemical content. Significant increases of specific growth rate and total carbon content in biomass resulting in a higher CO₂ fixation rate were found with 5 % CO₂. The maximum biomass concentration, carbohydrate and fatty acid contents with 5 % CO₂ were significantly higher than those with air, while carbohydrate biosynthesis was most affected as compared to other biochemical components. Cytomic analysis revealed a rapid accumulation of neutral lipid in the late growth phase with more lipid bodies visualized by confocal laser scanning microscopy (CLSM), when nitrate consumption was accelerated with CO₂ supplementation. Gas chromatography mass spectrometry (GC-MS) analysis indicated that 5 % CO₂ favored the formation of C18:2, which led to a decrease in the degree of lipid unsaturation (DLU). These results proved that CO₂ supplementation was one of the most efficient methods to significantly prompt the growth of microalgae and increase the C/N ratio in the medium, which in turn regulated the carbon metabolic flux to enhance neutral lipid and fatty acid production in C. vulgaris.     

Optimization of CO2 concentration and light intensity for biodiesel production by Chlorella vulgaris FACHB-1072 under nitrogen deficiency with phosphorus luxury uptake

Microalgal biodiesel is an alternative bioenergy for the future. Nitrogen deprivation is usually used to increase lipid content in microalgae, however, it also lowers biomass production, resulting in not much increase of lipid productivity. Our previous study found that phosphorus played an important role in enhancing biodiesel productivity of C. vulgaris FACHB-1072 under nitrogen deficient condition. The aim of this study was to optimize two significant parameters of CO₂ concentration (0.03, 4, 6, 12 %) and light intensity (40, 120, 200 μmol photons m^-2 s^-1) with respect to biodiesel productivity and P uptake rate of C. vulgaris FACHB-1072. It was found that the optimized conditions were 4 % CO₂ concentration and 200 μmol photons m^-2 s^-1 light intensity. The maximum biodiesel productivity was 34.56 mg L^-1 day^-1; 2.7 times higher than the control (nutrient sufficient condition). Phosphorus was accumulated as polyphosphate and its maximum uptake rate was 2.08 mg L^-1 day^-1; twice that of the control. After optimization, the performances under nitrogen deficiency were significantly better compared with those under nitrogen sufficiency, which were rarely reported in literature. Our findings suggest a great potential to combine phosphorus removal from wastewater with biodiesel production via microalgae.     

Evaluation of drying methods on nutritional constituents and antioxidant activities of Chlorella vulgaris cultivated in an outdoor open raceway pond

Chlorella vulgaris is known for its protein, growth factor, and nutritional constituents. Chlorella vulgaris was cultivated in a 1000-L outdoor open raceway pond with a maximum volumetric productivity of 130 mg L^-1 day^-1. The harvested biomass was dried through different methods, viz., sun drying (30 °C), oven drying (60 °C), lyophilization (?110 °C), drum drying (120 °C), and spray drying (100–150 °C). The effect of the drying method on proximate composition, pigments (chlorophyll, carotenoids), bioactive compounds (total phenolic content, flavonoid content), vitamin B₁₂, antioxidant properties (ferric reducing antioxidant power, DPPH, and total antioxidant activity), and the color quality of C. vulgaris biomass was evaluated. Surface characterization by scanning electron microscopy (SEM) and functional group characterization through Fourier transform infrared spectroscopy were also performed. The biomass dried through lyophilization and sun drying retained maximum bioactive compounds and antioxidant activities. In contrast, drum drying resulted in a loss of nutrients, viz., protein (up to 44%), lipid (up to 41%), vitamin B₁₂ (up to 40%), total phenolic content (> 50%), total flavonoid content (> 50%), and antioxidant activity (> 50%). Oven drying led to a loss of 30% in total flavonoid content and 17% in ferric reducing antioxidant power. SEM showed the destruction of cell wall integrity in the drum-dried sample and porous structure in the spray-dried sample. This study suggests that drying methods affect the nutrients and bioactive compounds of C. vulgaris biomass, and therefore a drying method should be selected carefully depending on the end use of the biomass.

     

Low-cost cultivation of <Emphasis Type="Italic">Scenedesmus</Emphasis> sp. with filtered anaerobically digested piggery wastewater: biofuel production and pollutant remediation

A laboratory study was conducted on biomass and lipid production by Scenedesmus sp. and the removal of total nitrogen (TN) and total phosphorus (TP) from filtered anaerobically digested piggery wastewater. The dry weight (DW), lipid content and productivity, total nitrogen, and total phosphorus removal rate were assessed in five media: modified soil extract (MSE) medium, 5 % anaerobic digested wastewater (ADWW), 10 % ADWW, 15 % ADWW, and 5 % ADWW supplemented with NaNO₃. The highest biomass productivity appeared in the 15 % ADWW group, which was 20.4 % higher than MSE group. The highest lipid content was found in the 5 % ADWW group (31.60 %), while the highest lipid productivity was in the 10 % ADWW group (27.01 mg L^?1 day^?1). Compared with the 5 % ADWW group, the 5 % ADWW group supplemented with NaNO₃ had a similar biomass amount but lower lipid content and productivity. The fatty acids percentage of Scenedesmus sp. showed a slight difference in different media, but with the four dominant fatty acids (C16:0, C18:1, C18:2, C18:3) accounting for 87 % of the total fatty acids, suggests that Scenedesmus sp. in ADWW medium was no different than MSE in terms of lipid composition and content. TN removal rates were 82.85, 82.51, 85.85, 91.28, and 78.71 % in groups 1 to 5, and TP removal rates were 53.05, 88.53, 87.77, 88.72, and 80.64 %. Our experiment also shows the feasibility of using ADWW as a substitute of all the elements of MSE medium except for carbon, which would significantly reduce the costs of microalgal culture.     

<Emphasis Type="Italic">Chlorella vulgaris</Emphasis> (SAG 211-12) biofilm formation capacity and proposal of a rotating flat plate photobioreactor for more sustainable biomass production

Difficulties and cost of suspended microalgal biomass harvest and processing can be overcome by cultivating microalgae as biofilms. In the present work, a new photoautotrophic biofilm photobioreactor, the rotating flat plate photobioreactor (RFPPB), was developed aiming at a cost-effective production of Chlorella vulgaris (SAG 211-12), a strain not frequently referred in the literature but promising for biofuel production. Protocols were developed for evaluating initial adhesion to different materials and testing the conditions for biofilm formation. Polyvinyl chloride substrate promoted higher adhesion and biofilm production, followed by polypropylene, polyethylene, and stainless steel. The new RFPPB was tested, aiming at optimizing incident light utilization, minimizing footprint area and simplifying biomass harvesting. Tests show that the photobioreactor is robust, promotes biofilm development, and has simple operation, small footprint, and easy biomass harvest. Biomass production (dry weight) under non-optimized conditions was 3.35 g m^?2, and areal productivity was 2.99 g m^?2 day^?1. Lipid content was 10.3% (dw), with high PUFA content. These results are promising and can be improved by optimizing some operational parameters, together with evaluation of long-term photobioreactor maximum productivity.     

Euglena sp. as a suitable source of lipids for potential use as biofuel and sustainable wastewater treatment

Prolific algal growth in sewage ponds with high organic loads in the tropical regions can provide cost-effective and efficient wastewater treatment and biofuel production. This work examines the ability of Euglena sp. growing in wastewater ponds for biofuel production and treatment of wastewater. The algae were isolated from the sewage treatment plants and were tested for their nutrient removal capability. Compared to other algae, Euglena sp. showed faster growth rates with high biomass density at elevated concentrations of ammonium nitrogen (NH₄-N) and organic carbon (C). Profuse growth of these species was observed in untreated wastewaters with a mean specific growth rate (μ) of 0.28 day^?1 and biomass productivities of 132 mg ?L^?1? day^?1. The algae cultured within a short period of 8 days resulted in the 98 % removal of NH₄-N, 93 % of total nitrogen 85 % of ortho-phosphate, 66 % of total phosphate and 92 % total organic carbon. Euglenoids achieved a maximum lipid content of 24.6 % (w/w) with a biomass density of 1.24 g ?L^?1 (dry wt.). Fourier transform infrared spectra showed clear transitions in biochemical compositions with increased lipid/protein ratio at the end of the culture. Gas chromatography and mass spectrometry indicated the presence of high contents of palmitic, linolenic and linoleic acids (46, 23 and 22 %, respectively), adding to the biodiesel quality. Good lipid content (comprised quality fatty acids), efficient nutrient uptake and profuse biomass productivity make the Euglena sp. as a viable source for biofuel production in wastewaters.     

Enhancing lipid production of the marine diatom Chaetoceros gracilis: synergistic interactions of sodium chloride and silicon

Silicon deficiency is a lipid-promoting stress for many oleaginous diatoms. Literature reports suggest that reduced salinity in seawater, a primary component of which is sodium chloride, may inhibit metabolism of silicon in marine diatoms. We hypothesized that lowering sodium chloride below ocean levels may thus be effective in creating silicon stress and enhancing lipid productivity. We examined the interacting effects of silicon supply (0.05, 0.1, 0.2, and 0.8 mM) and sodium chloride concentration (50, 100, and 400 mM) on growth and lipid production in Chaetoceros gracilis. This was done in batch culture to facilitate the application of severe stress. Low levels of either sodium chloride or silicon resulted in at least 50 % increases in lipid content. The synergy of simultaneous, moderate sodium chloride and silicon stress resulted in lipid content up to 73 % of dry mass and lipid productivity of 1.7 g m^?2 day^?1; with a daily integrated photosynthetic photon flux of 17.3 mol photons m^?2 day^?1, the efficiency of lipid synthesis was thus 0.1 g mol^?1 of photons. Decreased silicon also resulted in a 5 % shift in lipid chain length from C18 to C16 fatty acids. We observed a strong sodium chloride/silicon interaction on total and ash-free dry mass densities that arose because low sodium chloride concentrations were inhibitory to growth, but the inhibition was overcome with excessive silicon supply. This observation suggests that low levels of sodium chloride may have affected metabolism of silicon. The findings of this study can be used to enhance lipid production in oleaginous marine diatoms.