Laccase production by free and immobilized mycelia of Peniophora cinerea and Trametes versicolor: a comparative study

The production of laccase by immobilized mycelia of Peniophora cinerea and Trametes versicolor was studied. In an initial stage, experimental assays were performed in Erlenmeyer flasks using free and immobilized mycelium, and the performance of the fungal strains to produce the enzyme was compared. Both fungi adhered into the support material (a synthetic fiber), growing not only on the surface but also in the interspaces of the fibers. Immobilization of P. cinerea provided a 35-fold increase in laccase production when compared to the production obtained by using free mycelium. On the other hand, immobilization of T. versicolor caused a decrease in laccase activity. A comparison between the strains revealed that immobilized P. cinerea (3,500 U/L) surpassed the enzyme production by free T. versicolor (800 U/L). When the conditions that gave the best laccase production to each fungus were employed in a stirred tank bioreactor, very low laccase production was observed for both the cases, suggesting that shear stress and mycelia damage caused by the agitation impellers negatively affected the enzyme production.     

Comparative studies on immobilized laccase behaviour in packed-bed and batch reactors

Extracellular laccase produced by the wood-rotting fungus Cerrena unicolor was immobilized covalently via glutaraldehyde to cellulose-based carrier Granocel. Laccase was partially purified by membrane concentration and diafiltration followed by precipitation with acetone. Five-fold increase in the measured activity of immobilized enzyme was obtained when six times purer laccase was used for immobilization. For the best preparation, with very high activity of 2053 U per 1 mL of the carrier, thermal- and pH-stability, and activity profiles were determined. Experiments carried out in a batch reactor showed that k_cat/K_m for immobilized enzyme (0.65) is three times lower than the value obtained for the native laccase (2.19) whereas k_cat/K_m estimated from continuous reactor (1.50) is notably closer to that for the native enzyme. Continuous process probably reflects more precisely kinetics of the reaction accompanied by simultaneous product precipitation on the carrier’s surface. Operational stability of immobilized laccase was tested in continuous mode operation with ABTS, guaiacol and trichlorophenol as substrates and showed that packed-bed reactor is unprofitable system for laccase immobilized on Granocel carrier due to the high bed compaction. However, excellent stability of the preparation was noted under 20 successive runs in the well mixed tank reactor and better ability towards trichlorophenol biotransformation was observed in the case of immobilized laccase.     

Characterization and immobilization of the laccase from Pleurotus ostreatus and its use for the continuous elimination of phenolic pollutants

A laccase, the only ligninolytic enzyme produced by the basidiomycete Pleurotus ostreatus strain RK 36 was purified to homogeneity and characterized. The enzyme is a monomeric protein with a molecular weight of 67 000 Da and an isoelectric point of 3.6. Type I and type III Cu(2+) centers were identified by spectrophotometry. With syringaldazine as substrate laccase showed the highest oxidation rates at pH 5.8, 50 degrees C, and in 40 mM phosphate buffer. Among the tested stabilization parameters laccase retained most of its activity in high ionic buffer, pH 10, -20 degrees C, in the presence of 10 mM benzoic acid and with 35% ethylene glycol respectively. Crude laccase was covalently immobilized to Eupergit((R))C. Benzoate was found to stabilize the enzyme during the immobilization process. The activity loss of laccase during 10 days at 25 degrees C storage was 2% on average. Continuous elimination of 2,6-dimethoxyphenol by immobilized laccase was carried out in a packed bed reactor followed by filtration of the formed precipitate. The solubility of the polymerisates of oxidized syringaldazine, o-dianisidine, and 2,6-dimethoxyphenol with respect to temperature, pH-value and organic solvents were examined. The precipitates were found to be insoluble under non-extreme environmental conditions.     

Stability and kinetic behavior of immobilized laccase from Myceliophthora thermophila in the presence of the ionic liquid 1‐ethyl‐3‐methylimidazolium ethylsulfate

The use of ionic liquids (ILs) as reaction media for enzymatic reactions has increased their potential because they can improve enzyme activity and stability. Kinetic and stability properties of immobilized commercial laccase from Myceliophthora thermophila in the water‐soluble IL 1‐ethyl‐3‐methylimidazolium ethylsulfate ([emim][EtSO₄]) have been studied and compared with free laccase. Laccase immobilization was carried out by covalent binding on glyoxyl–agarose beads. The immobilization yield was 100%, and the activity was totally recovered. The Michaelis‐Menten model fitted well to the kinetic data of enzymatic oxidation of a model substrate in the presence of the IL [emim][EtSO₄]. When concentration of the IL was augmented, the values of V_max for free and immobilized laccases showed an increase and slight decrease, respectively. The laccase–glyoxyl–agarose derivative improved the laccase stability in comparison with the free laccase regarding the enzymatic inactivation in [emim][EtSO₄]. The stability of both free and immobilized laccase was slightly affected by small amounts of IL (<50%). A high concentration of the IL (75%) produced a large inactivation of free laccase. However, immobilization prevented deactivation beyond 50%. Free and immobilized laccase showed a first‐order thermal inactivation profile between 55 and 70°C in the presence of the IL [emim][EtSO₄]. Finally, thermal stability was scarcely affected by the presence of the IL. © 2014 American Institute of Chemical Engineers Biotechnol. Prog., 30:790–796, 2014     

Laccase-mediated Remazol Brilliant Blue R decolorization in a fixed-bed bioreactor

A crude laccase mixture preparation from Pleurotus ostreatus cultures supplemented with copper and ferulic acid was used to decolorize the anthraquinonic dye Remazol Brilliant Blue R (RBBR). Performance of this enzymatic system was tested, and a maximum of 70% decolorization was achievable under optimal conditions. The crude preparation was immobilized by entrapment in copper alginate beads attaining 65% yield of laccase activity. Stability of the immobilized laccases was remarkably increased in comparison with that of the free enzyme preparation. Efficiency of the immobilized system was evaluated during stepwise dye additions in batch operations. Under the best conditions, 70% RBBR decolorization was achieved even after 20 cycles, although decolorization time exponentially increased after the 10th cycle. Different fixed-bed bioreactors were prepared and analyzed in continuous decolorization processes. The best performance was obtained by decreasing the amount of enzyme loaded and by improving laccase retention using chitosan-coated alginate beads.     

Bacterial cellulose as carrier for immobilization of laccase: Optimization and characterization

Bacterial cellulose (BC) has attracted attention as a new functional material due to its excellent mechanical strength, tridimensional nanostructure, high purity, and increased water absorption, compared to plant cellulose. In this work, commercial laccase was immobilized on BC and the influence of enzyme concentration, contact time, and pH was optimized toward the recovery activity of immobilized laccase. This optimization was carried out using a 3³ experimental design and response surface methodology. Enzyme concentration played a critical role in laccase immobilization. Under optimized conditions (0.15 μL L^?1 of enzyme concentration, 4.8 h of contact time, pH 5.4), the predicted and experimental response were equal to 47.88 and 49.30%, respectively. The thermal stability of the immobilized laccase was found to increase notably at 60 and 70°C presenting stabilization factor equal to 1.79 and 2.11, respectively. The immobilized laccase showed high operational stability, since it retained 86% of its initial activity after seven consecutive biocatalytic cycles of reaction with 2,2′‐azinobis‐(3‐ethylbenzothiazoline‐6‐sulfonic acid). Kinetic studies showed that the values of Michaelis–Menten constant and maximum reaction rate decreased upon immobilization (9.9‐ and 1.6‐fold, respectively). Globally, the use of immobilized laccase on BC offers an interesting tool for industrial biocatalytic applications.     

桦褶孔菌漆酶固定化及其对染料的降解

采用壳聚糖交联法和海藻酸钠-壳聚糖包埋交联法固定化桦褶孔菌产生的漆酶,探讨最佳固定化条件,固定化漆酶的温度,pH稳定性及操作稳定性,并以两种固定化酶分别对4种染料进行了降解.结果表明:(1)壳聚糖交联法固定化漆酶的最佳条件为:壳聚糖2.5%,戊二醛7%,交联时间2h,固定化时间5h,给酶量1g壳聚糖小球:1mL酶液(1U/mL),固定化效率56%;(2)海藻酸钠-壳聚糖包埋交联法固定化漆酶的最佳条件为:海藻酸钠浓度4%,壳聚糖浓度0.7%,氯化钙浓度5%,戊二醛浓度0.6%,给酶量4mL 4%海藻酸钠:1mL酶液(1U/mL),固定化效率高达86%;(3)固定化的漆酶相比游离漆酶有更好的温度和pH稳定性;(4)比较两种固定化漆酶,海藻酸钠-壳聚糖包埋交联法固定化酶的温度及酸度稳定性要优于壳聚糖固定化酶,但可重复操作性要弱于后者,两者重复使用8次后的剩余酶活比率分别为71%及64%;(5)两种固定化酶对所选的4种不同结构的合成染料均有较好的降解效果,其中壳聚糖固定化酶对茜素红的降解效果及重复使用性极佳,重复降解40mg/L的茜素红10次,降解率仍保持在100%.     

金属框架结构材料MOF-199对漆酶的固定化及其性质

以金属框架结构材料MOF-199为载体对漆酶进行固定化,并对固定化酶的性质进行初步研究。首先,以3-氨基丙基三乙氧基硅烷对载体MOF-199进行表面氨基化修饰,再用戊二醛对载体进行活化,最后对漆酶进行固定化。固定化条件优化结果表明:在漆酶质量浓度0.3 g/L,戊二醛用量1%(体积分数),pH 4.8下固定7 h,制得固定化酶活性最高。对固定化酶的研究发现:最适反应温度为40℃,最适pH为5.2,在连续操作7次后,固定化酶的活力仍能保持在51%。固定化漆酶热稳定性,pH耐受性,贮存稳定性均明显高于游离漆酶。     

Laccase immobilization on enzymatically functionalized polyamide 6,6 fibres

Polyamide matrices, such as membranes, gels and non-wovens, have been applied as supports for enzyme immobilization, although in literature the enzyme immobilization on woven nylon matrices is rarely reported. In this work, a protocol for a Trametes hirsuta laccase immobilization using woven polyamide 6,6 (nylon) was developed. A 2⁴ full factorial design was used to study the influence of pH, spacer (1,6-hexanediamine), enzyme and crosslinker concentration on the efficiency of immobilization. The factors enzyme dosage and spacer seem to have played a critical role in the immobilization of laccase onto nylon support. Under optimized working conditions (29 U mL⁻¹ of laccase, 10% of glutaraldehyde, pH = 5.5, with the presence of the spacer), the half-life time attained was about 78 h (18% higher than that of free enzyme), the protein retention was 30% and the immobilization yield was 2%. The immobilized laccase has potential for application in the continuous decolourization of textile effluents, where it can be applied into a membrane reactor.     

Decolorization and detoxication of reactive industrial dyes by immobilized fungi <Emphasis Type="Italic">Trametes pubescens</Emphasis> and <Emphasis Type="Italic">Pleurotus ostreatus</Emphasis>

Trametes pubescens and Pleurotus ostreatus, immobilized on polyurethane foam cubes in bioreactors, were used to decolorize three industrial and model dyes at concentrations of 200, 1000 and 2000 ppm. Five sequential cycles were run for each dye and fungus. The activity of laccase, Mn-dependent and independent peroxidases, lignin peroxidase, and aryl-alcohol oxidase were daily monitored during the cycles and the toxicity of media containing 1000 and 2000 ppm of each dye was assessed by the Lemna minor (duckweed) ecotoxicity test. Both fungi were able to efficiently decolorize all dyes even at the highest concentration, and the duckweed test showed a significant reduction (p 相似文献   

Immobilization of lipase on epoxy activated (1-->3)-alpha-D-glucan isolated from Penicillium chrysongenum

A water-insoluble linear (1-->3)-alpha-D-glucan was isolated from Penicillium mycelia. Three kinds of epoxy-activated microspheres of this glucan were prepared as supports for Candida sp. lipase (EC3.1.1.3) immobilization. The highest immobilization yield was 36.4%. The specific activity was 26.85 U/mg, and only 4.1% of activity was lost in comparison with the free enzyme used for immobilization. The higher thermal stability, storage stability, and reusability of the immobilized lipase make it a potential candidate for wide application.     

Preparation and characterization of epoxy-functionalized magnetic chitosan beads: laccase immobilized for degradation of reactive dyes

Cross-linked magnetic chitosan beads were prepared by phase-inversion technique in the presence of epichlorohydrin under alkaline condition, and used for covalent immobilization of laccase. The activity of the immobilized laccase on the magnetic chitosan was about 260 U (g/dry beads) with an enzyme loading of about 16.33 ± 0.39 mg [(g/dry beads) mg/g]. Kinetic parameters, V _max and K _m values were determined as 21.7 U/mg protein and 9.4 μM for free enzyme, and 15.6 U/mg protein and 19.7 μM for the immobilized laccase, respectively. The operational and thermal stabilities of the immobilized laccase were improved compared to free counterpart. The immobilized laccase was operated in a batch reactor for the decolorization of reactive dyes from aqueous solution. The laccase immobilized on magnetic chitosan beads was very effective for removal of textile dyes from aqueous solution which creates an important environmental problem in the discharged textile dying solutions.     

Immobilization of pycnoporus coccineus laccase on Eupergit C: Stabilization and treatment of olive oil mill wastewaters

The use of olive oil mill wastewaters (OMW) as an organic fertilizer is limited by their phytotoxic effect, due to the high concentration of phenolic compounds. As an alternative to physico-chemical methods for OMW detoxification, the laccase from Pycnoporus coccineus, a white-rot fungus with the ability to decrease the chemical oxygen demand (COD) and color of the industrial effluent, is being studied. In this work, the P. coccineus laccase was immobilized on two acrylic epoxy-activated resins, Eupergit C and Eupergit C 250L. The highest activity was obtained with the macroporous Eupergit C 250L, reaching 110 U g^?1 biocatalyst. A substantial stabilization effect against pH and temperature was obtained upon immobilization. The soluble enzyme maintained ≥80% of its initial activity after 24 h at pH 7.0–10.0, whereas the immobilized laccase kept the activity in the pH range 3.0–10.0. The free enzyme was quickly inactivated at temperatures >50°C, whereas the immobilized enzyme was very stable up to 70°C. Gel filtration profiles of the OMW treated with the immobilized enzyme (for 8 h at room temperature) showed both degradation and polymerization of the phenolic compounds.     

Biodiesel production from pomace oil by using lipase immobilized onto olive pomace

In the present work, microbial lipase from Thermomyces lanuginosus was immobilized by covalent binding onto olive pomace. Immobilized support material used to produce biodiesel with pomace oil and methanol. The properties of the support and immobilized derivative were evaluated by scanning electron microscopy (SEM). The maximum immobilization of T. lanuginosus was obtained as 18.67 mg/g support and the highest specific activity was 10.31 U/mg protein. The properties of immobilized lipase were studied. The effects of protein concentration, pH and buffer concentration on the immobilization and lipase activity were investigated. Biodiesel production using the immobilized lipase was realized by a three-step addition of methanol to avoid strong substrate inhibition. Under the optimized conditions, the maximum biodiesel yield was 93% at 25 °C in 24 h reaction. The immobilized enzyme retained its activity during the 10 repeated batch reactions.     

Specific immobilization of laccase onp-benzoquinone-activated supports

Summary A specific immobilization of laccase (EC 1.10.3.2) onto a ready-to-usep-benzoquinone-activated agarose support is described. The single-step procedure leads to a laccase protein coupling of I8% and an enzyme activity immobilization yield of 27%, while the retained specific activity of the immobilized enzyme was 150% of the specific activity of the free laccase. This peculiar result is thought to be related to the fact that during the process of support activation byp-benzoquinone, a significant amount of the hydroquinone by-product of the activation process is coupled to the support. These coupled derivatives constitute substrate (hydroquinone) analogues for which laccase exhibits a high affinity. Therefore, simultaneous affinity retention on the hydroquinone groups and covalent coupling on the p-benzoquinone groups allow the binding of the enzyme in an advantageous conformation which can generate this increase specific activity by immobilization. The entire process can be considered as an affinity immobilization. The immobilized enzyme is much more stable to the inhibitory action of chloride and azide ions, with a recovery of 100% of the activity, than the free laccase, with a recovery of 67% and 32%, respectively, after removal of the inhibitors by dialysis. The stability was 95% after storage for 14 months at 4° C.Abbreviations HQ hydroquinone - p-BQ p-benzoquinone - U enzyme units Part of the work was presented at the Satellite FEBS 1989 Symposium onBiochemical and biophysical approaches to the study of copper proteins, Camerino, Italy.     

Immobilization of an amino acid racemase for application in crystallization‐based chiral resolutions of asparagine monohydrate

Integration of racemization and a resolution process is an attractive way to overcome yield limitations in the production of pure chiral molecules. Preferential crystallization and other crystallization‐based techniques usually produce low enantiomeric excess in solution, which is a constraint for coupling with racemization. We developed an enzymatic fixed bed reactor that can potentially overcome these unfavorable conditions and improve the overall yield of preferential crystallization. Enzyme immobilization strategies were investigated on covalent‐binding supports. The amino acid racemase immobilized in Purolite ECR 8309F with a load of 35 mg‐enzyme/g‐support showed highest specific activity (approx. 500 U/g‐support) and no loss in activity in reusability tests. Effects of substrate inhibition observed for the free enzyme were overcome after immobilization. A packed bed reactor with the immobilized racemase showed good performance in steady state operation processing low enantiomeric excess inlet. Kinetic parameters from batch reactor experiments can be successfully used for prediction of packed bed reactor performance. Full conversions could be achieved for residence times above 1.1 min. The results suggest the potential of the prepared racemase reactor to be combined with preferential crystallization to improve resolution of asparagine enantiomers.     

Immobilization of Laccase by Alginate–Chitosan Microcapsules and its Use in Dye Decolorization

Laccase is a ligninolytic enzyme that is widespread in white-rot fungi. Alginate–chitosan microcapsules prepared by an emulsification–internal gelation technique were used to immobilize laccase. Parameters of the immobilization process were optimized. Under the optimal immobilization conditions (2% sodium alginate, 2% CaCl₂, 0.3% chitosan and 1:8 ratio by volume of enzyme to alginate), the loading efficiency and immobilized yield of immobilized laccase were 88.12% and 46.93%, respectively. Laccase stability was increased after immobilization. Both the free and immobilized laccase alone showed a very low decolorization efficiency when Alizarin Red was selected for dye decolorization test. When 0.1 mM 2,2′-azino-bis-(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) was added into the decolorization system, the decolorization efficiency increased significantly. Immobilized laccase retained 35.73% activity after three reaction cycles. The result demonstrated that immobilized laccase has potential application in dyestuff treatment.     

Immobilization of laccase onto spacer-arm attached non-porous poly(GMA/EGDMA) beads: application for textile dye degradation

Non-porous poly(glycidyl methacrylate/ethyleneglycol dimetacrylate) (poly(GMA/EGDMA)) beads were prepared by suspension polymerization. The enzyme (i.e. laccase) was covalently immobilized onto plain and spacer-arm attached poly(GMA/EGDMA) beads. The amount of immobilized enzyme on the plain and spacer-arm attached beads was determined as 5.6 and 4.9 mg/g, respectively. The maximum activity (V(max)) and Michaelis constant (K(m)) of laccase immobilized on the spacer-arm attached beads, were found to be 77.6 U/min and 0.47 mM, respectively. Finally, the immobilized laccase was operated in a batch system, and textile dye Reactive Red 120 was successfully decolorized in the enzyme reactor.     

Enzyme immobilization by radiation-induced polymerization of 2-hydroxyethyl methacrylate at low temperatures.

Enzyme immobilization by radiation-induced polymerization of hydrophilic glass-forming monomers, such as 2-hydroxyethyl methacrylate, was studied. Enzyme radiation damage could be sufficiently retarded at low temperatures. The immobilized enzyme activity yield was markedly higher at low temperature than at higher temperature polymerization. At low temperatures the polymerized composite had a porous structure owing to ice crystallization which depends on the monomer concentration. It was deduced that the enzyme was partially trapped on the polymer surface, partially isolated in the pore, and partially occluded inside the polymer matrix. A decrease in activity caused by enzyme leakage was observed with repeated use in enzyme reactions where the composites had a large porosity. The activity yield showed a maximum at certain optimum porosities, i.e., at optimum monomer concentrations. Continuous enzyme reaction was preferably carried out using immobilized enzyme columns.