土壤中选育产壳聚糖酶菌株的研究

采用酶法降解壳聚糖具有反应条件易于控制、产物安全性高和环境污染少等独特的优越性。因此,筛选出高活力产壳聚糖酶菌株有着重要意义。该研究以不同地区采集土样分离出的1株细菌为出发菌株S,采用紫外线诱变（30W,20cm,5min）,经初筛和复筛及控温培养处理,获得了一株产壳聚糖酶较好的突变菌株,结果表明：所产酶活力达到3．47U/ml,酶活力提高近2倍,并具有较好的遗传稳定性,明显优于出发菌株,为发酵产壳聚糖酶的进一步研究提供了高产菌株。     

产壳聚糖酶菌株的初步筛选

通过大量的筛选,获得了产壳聚糖酶较好的菌株Y2、Y4、Y8。其发酵液所产壳聚糖酶的酶活力分别为2．0U／ml,2．1U／ml,2．2U／ml。     

产壳聚糖酶菌株的发酵条件优化

方法:通过单因子实验,对保存的1株产壳聚糖酶的菌株C001进行发酵产酶条件优化,确定了最适产酶培养基组分.结果:温度30℃,发酵时间18h,pH5.5,接种量5%优化发酵条件后,产壳聚糖酶活力增长了37.4%.     

产壳聚糖酶菌株的分离筛选及其诱变育种

利用以壳聚糖为唯一碳源的选择性培养基,从自然界中筛选得到一株壳聚糖酶活较高的菌株 ,其壳聚糖酶活为0.59U/mL.经初步鉴定,该菌株为芽孢杆菌属,以A表示.以该芽孢杆菌为出发菌株,经硫酸二乙酯(DES)诱变处理50 min后,筛选得到壳聚糖酶活明显提高的突变株DES-4,其壳聚糖酶活为1.60U/mL,是出发菌株的2.7倍.该突变株经连续传代5次后仍稳定产酶.研究表明,突变株DES-4的壳聚糖酶产生与芽孢形成之间关系密切,当芽孢充分形成后发酵液的壳聚糖酶活力不再增大.     

壳聚糖酶产生菌的筛选及固定化细胞产酶

旨在筛选得到一株壳聚糖酶产生菌,并研究固定化细胞产酶的条件。在培养基中以壳聚糖为唯一碳源,对土壤样品进行筛选,获得一株无花果沙雷氏菌(Serratia ficaria CH-0203),该菌可被壳聚糖诱导产生壳聚糖酶。固定化细胞产酶的研究结果表明,多孔玻璃可以有效吸附CH—0203菌细胞。在最适发酵条件下(pH6．5,培养基与载体的总体积48ml,载体与培养基的比例为1．5g/4．0ml,吸附时间是20h-26h),发酵液酶活达到4．5U／ml,比游离细胞发酵提高了16％。采用半连续发酵的方式,固定化的细胞可以稳定发酵产酶120h左右。固定化细胞产酶的效率大大高于游离细胞。     

壳聚糖酶生产菌的筛选、鉴定及其产酶培养条件的研究

从土样中分离到60株分泌胞外壳聚糖酶的菌株,经过筛选,其中有1株细菌产酶能力较高.生理生化试验鉴定该细菌为假单胞菌(Pseudomonas sp.).对假单胞菌产酶的培养条件研究结果表明:最适培养基组分为(g/L):壳聚糖5,氨基葡萄糖2,硝酸氨2,MgSO4·7H2O 0.5,KH2PO4 0.4,KCL 0.5,FeSO4·7H2O 0.01,起始pH 6.5;适宜培养条件是:接种量2.0×107个/50ml培养液,28℃,120 r/min振荡培养3d.     

产壳聚糖酶菌株的筛选、鉴定及酶学特性分析

【目的】利用筛选培养基,从福建沿海潮间带泥样中分离筛选产壳聚糖酶的菌株,并研究菌株的产酶特性。【方法】通过形态学观察,结合26S rDNA序列进行分类鉴定,采用DNS法测定酶活力。【结果】筛选得到产壳聚糖酶的菌株KQ-1002与草酸青霉(Penicillium oxalicum)的同源性为99%,并初步鉴定为青霉属的一种。发酵培养的最适温度为30°C,最适碳源为1.0%水溶性壳聚糖,最适氮源为1.87%(NH4)2SO4,最适pH为6.0。该菌株液体发酵培养72 h产壳聚糖酶活性最高,经优化后最高产酶量为18 U/mL。纯化后的壳聚糖酶经SDS-PAGE分析其分子量约40 kD。酶促反应最适pH为5.0,最适反应温度为55°C,Km值为1.293 g/L。在离子浓度为1.0×10 3mol/L时,金属离子Cu2+、Hg2+、Ag+对酶的活性均有强烈的抑制作用。壳聚糖酶对不同底物及脱乙酰度的壳聚糖具有不同的降解作用。【结论】筛选获得产壳聚糖酶的真菌菌株KQ-1002的壳聚糖酶活力经优化后提高了约7倍,是一株具有研究和应用潜力的产壳聚糖酶菌株。     

高产壳聚糖酶菌株的筛选及分类鉴定

目的：筛选一株高产壳聚糖酶的菌株。方法：通过形态学、生理生化及16S rDNA序列测定,对菌株进行分类鉴定。在培养基中以壳聚糖为唯一碳源,对长白山天池边的土样进行筛选。结果：获得一株产壳聚糖酶活力较高的菌株,最大酶活力达0．325U／ml。结论：经16S rDNA序列比对,该菌株与Beta proteobacterium的同源性高达99％。结合《伯杰细菌鉴定手册》（第九版）,将该菌株鉴定为Beta proteobacterium属的一个种,定名为Beta proteobacterium sp．T1。     

产壳聚糖酶菌株的分离、鉴定及发酵条件优化

从废弃食用菌培养基周围土壤中分离得到一株产壳聚糖酶的菌株,结合形态学特征与26SrDNA序列进行了分类学鉴定,结果表明,该菌株与高山被孢霉(Mortierella alpina)的同源性较高,达99%,初步鉴定为被孢霉属的一种,命名为KB-1001。并对该菌株的产酶特性进行了研究,结果表明,该菌株液体发酵培养产酶高峰出现在第84h,最适碳源为1%的水溶性壳聚糖,最适氮源为1.87%的(NH4)2SO4,摇瓶培养的最适初始pH值为6.0,最适温度为28℃～30℃,接种量为4%,最佳装瓶量为70 mL/250 mL,150 r/min摇瓶培养,经优化培养后,该菌株发酵液中壳聚糖酶活力最高达到8.130 U/mL。比原始的未经发酵条件优化的产酶活性提高了12.78%。     

高产壳聚糖酶菌株的筛选及分类鉴定

目的在于筛选一株高产壳聚糖酶的菌株,通过形态学、生理生化及16SrDNA序列测定,对菌株进行分类鉴定。对长白山天池边的土样进行筛选,获得一株产壳聚糖酶活力较高的菌株,最大酶活力达0．325U／mL。经16SrDNA序列比对,该菌株与Beta proteobacterium的同源性高达99％。结合《伯杰细菌鉴定手册》（第9版）,将该菌株鉴定为Beta proteobacterium属的一个种,定名为Betaproteobac-tenure sp．T1。     

Molecular Characterization of a Novel Family-46 Chitosanase from Pseudomonas sp. A-01

Pseudomonas sp. A-01, isolated as a strain with chitosan-degrading activity, produced a 28 kDa chitosanase. Following purification of the chitosanase (Cto1) and determination of its N-terminal amino acid sequence, the corresponding gene (cto1) was cloned by a reverse-genetic technique. The gene encoded a protein, composed of 266 amino acids, including a putative signal sequence (1-28), that showed an amino acid sequence similar to known family-46 chitosanases. Cto1 was successfully overproduced and was secreted by a Brevibacillus choshinensis transformant carrying the cto1 gene on expression plasmid vector pNCMO2. The purified recombinant Cto1 protein was stable at pH 5–8 and showed the best chitosan-hydrolyzing activity at pH 5. Replacement of two acidic amino acid residues, Glu23 and Asp41, which correspond to previously identified active centers in Streptomyces sp. N174 chitosanase, with Gln and Asn respectively caused a defect in the hydrolyzing activity of the enzyme.     

无花果沙雷氏菌CH0203壳聚糖酶的纯化及生化性质研究

目的：得到纯化的无花果沙雷氏菌CH02503的壳聚糖酶,并研究其生化性质。方法：将发酵粗酶液先后通过硫酸铵分级沉淀,superdex75凝胶柱和羧甲基纤维素离子交换柱层析,壳聚糖酶得到纯化。结果：经测定,该酶为内切酶,其相对分子质量为29kDa,等电点9．4,在45℃和pH4．0—7．5之间稳定,最适温度是45％,最适pH3．6,Mn^2＋、Co^2＋能够激活,Pb^2＋、Cu^2＋、Ni^2＋、Cr^3＋能够抑制该酶的活性,该酶最适底物是脱乙酰度85％的壳聚糖,对脱乙酰度低于45％的壳聚糖不能作用,对羧甲基甲壳素和羧甲基纤维素不能作用,以完全脱乙酰的壳聚糖为底物时,最终水解产物是单糖、二糖、三糖,反应的米氏常数为0．44mg／ml。     

芽孢杆菌Bacillus sp. S-1壳聚糖酶基因的克隆与序列分析

从连云港海滩晒虾蟹壳的泥土里筛选出一株产壳聚糖酶能力较高的菌株S-1,根据其形态特征、生理生化以及16S rDNA鉴定,初步认定该菌为芽孢杆菌属（Bacillus）。利用NCBI数据库中已经报道的Bacillus壳聚糖酶序列设计兼并引物,以菌株Bacillus sp. S-1的基因组DNA为模板进行聚合酶链式反应（PCR）,克隆到壳聚糖酶基因的部分序列;利用Clontech公司Universal GenomeWalker试剂盒构建该菌株的基因组步移文库,根据已测定的序列信息设计特异性引物,结合两步法PCR技术分别克隆两端未知序列,拼接获得壳聚糖酶基因的全长序列（该基因全长1362 bp编码453个氨基酸,注册号：EU924147）,并对该序列进行了生物信息学方面的分析。     

高活性壳聚糖酶制剂的制备及其对壳聚糖降解作用的研究

对系列壳聚糖酶高产菌株的产酶性能及产酶发酵液的壳聚糖酶活性进行了比较,从中筛选出一株优良芽孢杆菌菌株,其产酶发酵液的壳聚糖酶活力高达5000U/mL(以单位时间内底物壳聚糖的减少量确定酶活力)。利用此粗制壳聚糖酶制剂对壳聚糖进行酶解产糖的研究表明:壳聚糖的转化率及壳寡糖的产率在适合的酶解条件下,短时间内即可接近100%。     

Isolation and Characterization of Chitosanase from the Strain Bacillus sp. 739

The specific nature of the chitosanase activity of the strain Bacillus sp. 739 was determined. Maximum enzyme activity was observed in a medium containing biomass of the fruiting bodies of the fungus Macrolepiota procera. The chitosanase was purified to homogeneity by chromatography on DEAE-Sephadex A-50 and Toyopearl HW-50. The molecular weight of the enzyme assessed by electrophoresis (the Laemmli procedure) approximated 46 kDa. The temperature and pH optima of the purified chitosanase were in the ranges 45–55°C and 6.0–6.5, respectively. Time to half-maximum inactivation of the enzyme at 50°C was equal to 1 h. With colloidal chitosan as the substrate, the value of K of the purified chitosanase was equal to 25 mg/ml. The enzyme also exhibited a weak ability to hydrolyze colloidal chitin.     

一株产丙烯腈水合酶菌株的研究

从山东省泰山地区土壤中分离到一株能产生丙烯腈水合酶的微生物菌株８６－１６３,经分类学特征鉴定可归属于诺卡氏菌属,其培养特征、生理生化特征及产酶活性等方面与已报导的诺卡氏菌有差别,暂定名为Ｎｏｃａｒｄｉａｓｐ．８６－１６３。     

Isolation and Characterization of A Metal-resistant Pseudomonas Aeruginosa Strain

Summary The use of microorganisms to remove heavy metals from industrial effluent is an area of extensive research and development. Attempts have been made to isolate and characterize metal-resistant microorganisms from treated oil mill industry effluent wastewater samples. The metal-resistant organisms that showed values of minimum inhibitory concentration towards metals (Cd, Cr, Ni and Pb) ranging from 100 to 800 ppm level were screened. A potent metal-resistant organism, isolate BC15 from the wastewater samples was tentatively identified as Pseudomonas sp. Detailed analysis of morphological, biochemical and 16S rDNA sequence of the isolate revealed that it is closely related to Pseudomonas aeruginosa (94%). Pseudomonas BC15 was capable of absorbing 93% Ni, 65% Pb, 50% Cd and 30% Cr within 48 h from the medium containing 100 mg of each heavy metal per liter. The multiple metal tolerance of this strain was also associated with resistance to antibiotics such as ampicillin, tetracycline, chloramphenicol, erythromycin, kanamycin and streptomycin.     

Beta proteobacterium sp.T1菌株产壳聚糖酶的分离纯化

目的:分离纯化Beta proteobacterium sp.T1菌株所产的壳聚糖酶.方法:采用(NH4)2SO4(20%～70%)分级盐析、阴离子交换树脂DEAE Cellulose 52柱层析、SephadexG-100柱层析技术进行分离纯化,采用SDS-PAGE鉴定酶的纯度、分子量.结果:经DEAE Cellulose 52柱层析,壳聚糖酶纯化了13.19倍;经Sephadex G-100柱层析,壳聚糖酶纯化了26.32倍.结论:纯化后的酶经SDS-PAGE鉴定已达到电泳纯,分子量29.5kDa.     

壳聚糖酶的克隆表达与壳寡糖的制备分析

目的:克隆壳聚糖酶基因于大肠杆菌中实现高表达,制备壳寡糖。方法:以枯草芽孢杆菌总DNA为模板扩增壳聚糖酶基因(CSN),克隆至载体pET23a(+)上,转化菌株BL21(DE3)。重组子经0.5 mmol/L IPTG诱导后,SDS-PAGE和质谱检测与鉴定重组酶。酶纯化后水解壳聚糖,薄层色谱分析其水解产物。结果:质谱证明壳聚糖酶(31.5kDa)成功表达,表达量占菌体总蛋白的45%左右。纯化后重组酶浓度为900 mg/L,纯度95%、回收率85%,酶活力为10 000 U/mg。壳聚糖降解产物为壳二糖至壳四糖。结论:原核表达载体pET23a(+)-CSN构建正确,壳聚糖酶表达量与活性高,适用于水解壳聚糖制备壳寡糖。