Medium optimization for the high yield production of single (+)-terrein by Aspergillus terreus strain PF26 derived from marine sponge Phakellia fusca

Terrein has potential application in the fields of medicine, cosmetology and agriculture, however, the chemical synthesis of terrein with single configuration is a difficult task, and the biosynthesis of terrein always results in low production (ca. 0.33–400 mg/L). In this study, we reported an Aspergillus terreus strain PF26 which could produce (+)-terrein on a high level. After the selection of a suitable basic medium, the component concentrations were optimized using Plackett–Burman design and response surface methodology. Consequently, an optimal medium containing 28.41 g glucose, 23.18 g maltose, 20.00 g mannitol, 8.52 g malt extract, 10.00 g monosodium glutamate 10.00 g NH₄Cl in 1 L ASW was obtained, and a high (+)-terrein production of 3.71 g/L fermentation broth was achieved, which represents the highest fermentation production of (+)-terrein to date. The result highlighted the industry's potential of A. terreus strain PF26 in the production of bioactive (+)-terrein on a large-scale.     

Purification of l-(+)-lactic acid from pre-treated fermentation broth using vapor permeation-assisted esterification

The vapor permeation-assisted esterification of l-(+)-lactic acid and ethanol was investigated using a zeolite membrane. Pervaporation and vapor permeation were initially investigated for dehydration performances, and the latter showed much better results. The molecular sieve property of the membrane resulted in a high separation factor of over 1000 for all conditions. The maximum flux was 10.24 kg/(m² h) at a feed temperature of 145 °C, a water feed concentration of 10 wt%, and a feed pressure of 4.0 bars, respectively. For vapor permeation-assisted esterification using synthetic solutions, the productivity and ethyl lactate yield strongly depended on the dehydration rate. Realistic purifications were performed with fermentation broths of Pediococcus pentosaceus as the lactic acid producer. Experimental results revealed that most of the lactic acid was converted into ethyl lactate at the final stage of the reaction. After distillation and hydrolysis, high purity l-(+)-lactic acid was obtained with more than 95% recovery yields.     

Evaluation of biocomposite-based supports for immobilized-cell xylitol production compared with a free-cell system

This study was conducted to evaluate the importance of aeration in free and immobilized cell systems in an aerated bioreactor for xylitol production from an oat hull hemicellulosic hydrolysate using an integrated process. The aeration rate (AR) or oxygen mass transfer coefficient (k_La) demonstrated a significant role in controlling cell (Candida guilliermondii FTI 20037) regeneration and bioconversion performance in free and immobilized cell systems. In the free cell system, an aeration rate of 1.25 vvm corresponding to k_La of 15.8 1/h resulted in maximum values of product yield (Y_p/s: 0.87 g/g), productivity (Q_p: 0.57 g/l/h), and final xylitol concentration (P_f: 55 g/l) from the hydrolysate with a 74.5 g/l xylose concentration. However, in the aerated immobilized cell system, maximum and almost similar results (almost P_f: 54 g/l, Q_p: 0.57 g/l/h and Y_p/s: 0.84 g/g) were obtained with aeration rates from 1.25 to 1.5 vvm using composites based on polypropylene (PP) and partially delignified fiber (PDF). Composites based on acid treated fiber (ATF) containing a high amount of lignin showed some inhibitory impact on xylose uptake and xylitol formation (P_f: 47 g/l and Q_p < 0.49 g/l/h) with the optimal aeration rate of 1.5 vvm in the initial cycle of the bioconversion; this inhibition impact could be resolved in the next consecutive cycles. The surface modifier polyethyleneimine (PEI) slightly enhanced cell retention in the immobilized form on the ATF-based cell support. This investigation helps fill in the knowledge gaps existing on the integrated processing of the lignocellulosic biomass for xylitol bioproduction and biorefinery industry; however, more scale-up studies are recommended for commercialization.     

Hyaluronic acid production and molecular weight improvement by redirection of carbon flux towards its biosynthesis pathway

Hyaluronic acid (HA) production in Streptococcus zooepidemicus competes for the carbon source along with biomass formation, lactate formation (via glycolysis) and pentose phosphate pathway (PPP). In our studies, increase in HA molecular weight was observed by redirecting the carbon flux towards HA biosynthesis pathway by partially inhibiting the glycolytic pathway. Batch bioreactor (1.2 L) studies showed that with the addition of 25 μM sodium iodoacetate, 5 g/L tryptophan and 10 g/L pyruvate, which are glycolytic inhibitors, HA molecular weight increased to 3.2, 3.2 and 3.1 MDa respectively compared to control run (2.4 MDa). Yield coefficients Y_HA/S and Y_LA/S showed inverse relationship, indicating competition for glucose between HA and lactic acid formation. Addition of 5 g/L glutamine along with 25 μM sodium iodoacetate also increased the HA concentration to 5.0 g/L from 2.0 g/L in control run. Metabolic flux analysis studies show that concentration and molecular weight of HA is increased by decreasing carbon flux towards glycolysis and PPP and increasing carbon flux towards HA precursor formation. It was observed that specific growth rate of the cells correlated positively to the specific HA production rate and negatively to the molecular weight of HA produced. Addition of antioxidant tannic acid also increased molecular weight to 3.0 MDa.     

Enhancement of pilot scale production of l(+)-lactic acid by fermentation coupled with separation using membrane bioreactor

Traditional batch fermentation leads to a higher energy consumption and lower production capability because of longer culture time. In this work, a pilot scale bioreactor composed of a 3000 L fermentor and external ceramic microfiltration equipment was used to perform cell-recycle fermentation. Repeat feeding medium was also used to relieve the substrate inhibition. In such pilot system, the maximum yield and productivity of l(+)-lactic acid production reached 157.22 ± 3.42 g/L and 8.77 ± 0.15 g/L/h which were 4.23% and 315.64% higher than those of batch fermentation, respectively, when equal amount of sugar was consumed. The cost of l(+)-lactic acid production was successfully reduced about two-thirds by the increase of yield and productivity. 12 rounds of cell-recycle fermentations were successfully achieved in the pilot system. The membrane filtration productivity reached to 61.27 ± 2.74 L/m²/h which increased 172.80%, while the cell damaging rate dropped to 3.88 ± 0.18% which decreased 85.77%, compared with those of the ultrafiltration. Furthermore, the ceramic microfiltration membrane showed advantages in tolerance for the temperature, pressure and acid, compared with the organic ultrafiltration membrane. The experimental results indicated that the method could give a reference for low cost production of l(+)-lactic acid in an industrial scale.     

A laboratory study of producing docosahexaenoic acid from biodiesel-waste glycerol by microalgal fermentation

Crude glycerol is the primary by-product in the biodiesel industry, which is too costly to be purified into to higher quality products used in the health and cosmetics industries. This work investigated the potential of using the crude glycerol to produce docosahexaenoic acid (DHA, 22:6 n-3) through fermentation of the microalga Schizochytrium limacinum. The results showed that crude glycerol supported alga growth and DHA production, with 75–100 g/L concentration being the optimal range. Among other medium and environmental factors influencing DHA production, temperature, trace metal (PI) solution concentration, ammonium acetate, and NH₄Cl had significant effects (P < 0.1). Their optimal values were determined 30 mL/L of PI, 0.04 g/L of NH₄Cl, 1.0 g/L of ammonium acetate, and 19.2 °C. A highest DHA yield of 4.91 g/L with 22.1 g/L cell dry weight was obtained. The results suggested that biodiesel-derived crude glycerol is a promising feedstock for production of DHA from heterotrophic algal culture.     

Kinetic modeling and implementation of superior process strategies for β-galactosidase production during submerged fermentation in a stirred tank bioreactor

This paper reports development and implementation of superior fermentation strategies for β-galactosidase production by Lactobacillus acidophilus in a stirred-tank bioreactor. Process parameters (aeration and agitation) were optimized for the process by application of Central Composite Design. Aeration rate of 0.5 vvm and agitation speed of 250 rpm were most suitable for β-galactosidase production (2001.2 U/L). Further improvement of the operation in pH controlled environment resulted in 2135 U/L of β-galactosidase with productivity of 142.39 U/L h. Kinetic modeling for biomass and enzyme production and substrate utilization were carried out at the aforementioned pH controlled conditions. The logistic regression model (X₀ = 0.01 g/L; X_max = 2.948 g/L; μ_max = 0.59/h; R² = 0.97) was used for mathematical interpretation of biomass production. Mercier's model proved to be better than Luedeking–Piret model in describing β-galactosidase production (P₀ = 0.7942 U/L; P_max = 2169.3 U/L; P_r = 0.696/h; R² = 0.99) whereas the latter was more efficient in mathematical illustration of lactose utilization (m = 0.187 g/g h; Y_x/s = 0.301 g/L; R² = 0.98) among the two used in this study. Strategies like fed-batch fermentation (3694.6 U/L) and semi-continuous fermentation (5551.9 U/L) further enhanced β-galactosidase production by 1.8 and 2.8 fold respectively.     

l-Lactic acid production from liquefied cassava starch by thermotolerant Rhizopus microsporus: Characterization and optimization

The thermotolerant Rhizopus microsporus DMKU 33 capable of producing l-lactic acid from liquefied cassava starch was isolated and characterized for its phylogenetic relationship and growth temperature and pH ranges. The concentrations of (NH₄)₂SO_4, KH₂PO₄, MgSO₄ and ZnSO₄·7H₂O in the fermentation medium was optimized for lactic acid production from liquefied cassava starch by Rhizopus microsporus DMKU 33 in shake-flasks at 40 °C. The fermentation was then studied in a stirred-tank bioreactor with aeration at 0.75 vvm and agitation at 200 rpm, achieving the highest lactic acid production of 84 g/L with a yield of 0.84 g/g at pH 5.5 in 3 days. Lactic acid production was further increased to 105–118 g/L with a yield of 0.93 g/g and productivity of 1.25 g/L/h in fed-batch fermentation. R. microsporus DMKU 33 is thus advantageous to use in simultaneous saccharification and fermentation for l-lactic acid production from low-cost starchy substrates.     

Dimeric argininamide-type neuropeptide Y receptor antagonists: Chiral discrimination between Y1 and Y4 receptors

The structurally related peptides neuropeptide Y (NPY), peptide YY (PYY) and pancreatic polypeptide (PP) are endogenous agonists of the NPY receptor (YR) family, which in humans comprises four functionally expressed subtypes, designated Y₁R, Y₂R, Y₄R and Y₅R. Nonpeptide antagonists with high affinity and selectivity have been described for the Y₁R, Y₂R and Y₅R, but such compounds are still lacking for the Y₄R. In this work, the structures of the high affinity selective (R)-argininamide-type Y₁R antagonists BIBP3226 and BIBO3304 were linked via the guanidine or urea moieties to give homo-dimeric argininamides with linker lengths ranging from 31 to 41 atoms. Interestingly, the twin compounds proved to be by far less selective for the Y₁R than the R-configured monovalent parent compounds. The decrease in selectivity ratio was most pronounced for Y₁R versus Y₄R subtype, resulting in comparable affinities of bivalent ligands for Y₁R and Y₄R (e.g. UR-MK177 ((R,R)-49): K_i = 230 nM (Y₁R) and 290 nM (Y₄R)). With a K_i value of 130 nM and a K_b value of 20 nM, UR-MK188 ((R,R)-51) was superior to all Y₄R antagonists known to date. The S,S-configured optical antipodes of UR-MK177 and UR-MK188 (UR-MEK381 ((S,S)-49) and UR-MEK388 ((S,S)-51)) were synthesized to investigate the stereochemical discrimination by the different receptor subtypes. Whereas preference for R,R-configured argininamides was characteristic of the Y₁R, stereochemical discrimination by the Y₄R was not observed. This may pave the way to selective Y₄R antagonists.     

Optimization of the medium for glutathione production in Saccharomyces cerevisiae

As a powerful statistical experimental design, uniform design (UD) method has been successfully applied in various fields such as fermentation industry, pharmaceuticals, and others. In this paper, UD was applied to optimize the medium composition for glutathione production in shake-flask culture of Saccharomyces cerevisiae T65. The experiments of nine factors (glucose, yeast extract, peptone, malt extract, molasses, MgSO₄, ZnSO₄, (NH₄)₂HPO₄ and thiamine) and nine levels were carried out according to the uniform design table U₂₇(9⁹). The experimental data was analyzed to obtain the regression model and the optimal medium composition was achieved by optimization with UD 3.0 software. The optimal medium consisted of 70 g/L glucose, 3 g/L yeast extract, 5 g/L peptone, 70 g/L malt extract, 20 g/L molasses, 5.6 g/L MgSO₄, 16 mg/L ZnSO₄, 7 g/L (NH₄)₂HPO₄ and 0.2 mg/L thiamine. The GSH yield at the optimal point achieved 74.6 mg/L, which was 1.81 times higher than that of the control. The application of UD method resulted in enhancement in GSH production.     

Mycophenolic acid production in solid-state fermentation using a packed-bed bioreactor

Mycophenolic acid (MPA) was produced from Penicillium brevicompactum by solid-state fermentation (SSF) using pearl barley, and submerged fermentation (SmF) using mannitol. It was found that SSF was superior to SmF in terms of MPA concentration (1219 mg/L vs. 60 mg/L after 144 h fermentation), and the product yields were 6.1 mg/g pearl barley for SSF and 1.2 mg/g mannitol for SmF. The volumetric productivities were 8.5 and 0.42 mg/L h for SSF and SmF, respectively.The optimum solid substrate of SSF for MPA production was pearl barley, producing 5470 mg/kg compared with wheat bran (1601 mg/kg), oat (3717 mg/kg) and rice (2597 mg/kg). The optimum moisture content, incubation time and inoculum concentrations were 70%, 144 h and 6%, respectively. Neither the addition of mannitol or (NH4)₂HPO₄ nor adjustment of media pH within the range of 3–7 significantly enhanced MPA production.MPA production by SSF using a packed-bed bioreactor was performed and an increased maximum production of MPA 6.9 mg/g was achieved at 168 h incubation time. The higher volumetric productivity and concentrations makes SSF an attractive alternative to SmF for MPA production.     

Application of liquid chromatography-tandem mass spectrometry (LC–MS/MS) for the analysis of stable isotope enrichments of phenylalanine and tyrosine

Whole-body protein synthesis and breakdown are measured by a combined tracer infusion protocol with the stable isotope amino acids l-[ring-²H₅]-phenylalanine, l-[ring-²H₂]-tyrosine and l-[ring-²H₄]-tyrosine that enable the measurement of the phenylalanine to tyrosine conversion rate. We describe a liquid chromatography–tandem mass spectrometry (LC–MS/MS) method for the measurement of very low tracer–tracee ratios (TTR) of the amino acids l-phenylalanine and l-tyrosine in human plasma. TTR calibration curves of the tracers l-[ring-²H₅]-phenylalanine, l-[ring-²H₂]-tyrosine and l-[ring-²H₄]-tyrosine were linear (r² > 0.99) in the range between 0.01% and 5.0% TTR and lowest measurable TTR for the tracers was 0.01% at a physiological concentration of 60 μM. The method was applied successfully to plasma samples from a clinical study reaching a steady state enrichment plateau (mean ± SD) of 3.33 ± 0.19% for l-[ring-²H₅]-phenylalanine, 2.40 ± 0.43% for l-[ring-²H₂]-tyrosine and 0.29 ± 0.07% for l-[ring-²H₄]-tyrosine, respectively. The LC–MS/MS method can be applied for measurement of very low plasma enrichments of phenylalanine and tyrosine for the determination of whole-body protein synthesis and breakdown rates in humans.     

Effect of the aeration rate and agitation speed on β-carotene production and morphology of Blakeslea trispora in a stirred tank reactor: mathematical modeling

The effect of aeration rate and agitation speed on β-carotene production and morphology of Blakeslea trispora in a stirred tank reactor was investigated. B. trispora formed hyphae, zygophores and zygospores during the fermentation. The zygospores were the morphological form responsible for β-carotene production. Both aeration and agitation significantly affected β-carotene concentration, productivity, biomass and the volumetric mass transfer coefficient (K_La). The highest β-carotene concentration (1.5 kg m⁻³) and the highest productivity (0.08 kg m⁻³ per day) were obtained at low impeller speed (150 rpm) and high aeration rate (1.5 vvm). Also, maximum productivity (0.08 kg m⁻³ per day) and biomass dry weight (26.4 kg m⁻³) were achieved at high agitation speed (500 rpm) and moderate aeration rate (1.0 vvm). Conversely, the highest value of K_La (0.33 s⁻¹) was observed at high agitation speed (500 rpm) and high aeration rate (1.5 vvm). The experiments were arranged according to a central composite statistical design. Response surface methodology was used to describe the effect of impeller speed and aeration rate on the most important fermentation parameters. In all cases, the fit of the model was found to be good. All fermentation parameters (except biomass concentration) were strongly affected by the interactions among the operation variables. β-Carotene concentration and productivity were significantly influenced by the aeration, agitation, and by the positive or negative quadratic effect of the aeration rate. Biomass concentration was principally related to the aeration rate, agitation speed, and the positive or negative quadratic effect of the impeller speed and aeration rate, respectively. Finally, the volumetric mass transfer coefficient was characterized by the significant effect of the agitation speed, while the aeration rate had a small effect on K_La.     

Effects of nutrients on arsenic accumulation by arsenic hyperaccumulator Pteris vittata L.

This research investigated the effects of various nutrients on arsenic (As) removal by arsenic hyperaccumulator Pteris vittata L. in a Hoagland nutrient solution (HNS). The treatments included different concentrations of Ca and K in 20% strength of HNS, different strengths of HNS (10, 20 and 30%), different strengths of HNS (10 and 20%) with and without CaCO₃, and different concentrations of Ca, K, NO₃, NH₄, and P in 20% strength of HNS. The plants were grown in nutrient solution containing 1 mg As L^?1 for 4 weeks except the Ca/K experiment where the plants were grown in nutrient solution containing 10 or 50 mg As L^?1 for 1 week. Adding up to 4 mM Ca or 3 mM K to 20% strength HNS significantly (P < 0.05) increased plant arsenic accumulation when the solution contained 10 mg As L^?1. Plant arsenic removal was reduced with increasing Ca and K concentrations at 50 mg As L^?1. Lower strength of HNS (10%) resulted in the greatest plant arsenic removal (79%) due to lower competition of P with As for plant uptake. Addition of CaCO₃ to 20% strength of HNS significantly increased arsenic removal by P. vittata. Among the nutrients tested, NO₃ and CaCO₃ were beneficial to plant arsenic removal while NH₄, P and Cl had adverse effects. This experiment demonstrated that it is possible to optimize plant arsenic removal by adjusting nutrients in the growth medium.     

Unmarked insertional inactivation in the gfo gene improves growth and ethanol production by Zymomonas mobilis ZM4 in sucrose without formation of sorbitol as a by-product,but yields opposite effects in high glucose

Sorbitol, one of the main by-products of growth on high sucrose concentrations, is catalyzed by glucose-fructose oxidoreductase (GFOR, EC 1.1.99.28) in Zymomonas mobilis, which decreases the ethanol yield. In this study, an unmarked gfo mutant from Z. mobilis ZM4 was constructed using a site-specific FLP recombinase, and growth and ethanol production were evaluated with or without the addition of sorbitol to the media. The inactivation of gfo had contrasting effects in different substrates, especially at high concentrations. The maximum specific growth rate (μ_m) and theoretical ethanol yield value (Y_m) increased from 0.065 h⁻¹ and 60.56% to 0.094 h⁻¹ and 83.87% in 342 g/L sucrose, respectively. Conversely, in 200 g/L glucose, gfo inactivation decreased μ_m and Y_m from 0.15 h⁻¹ and 89.85% to 0.10 h⁻¹ and 67.59%, respectively, and prolonged the lag period from 16 h to 40 h. The addition of sorbitol slightly accelerated growth and sucrose hydrolysis by the gfo mutant in 342 g/L sucrose; however, addition of sorbitol restored the μ_m and Y_m of the gfo mutant in 200 g/L glucose to 0.14 h⁻¹ and 82.50%, respectively. Inactivation of gfo had a small effect on fructose utilization, and a positive one on mixture of glucose and fructose similar to that on sucrose. These results provide further understanding of the osmoregulation mechanisms in Z. mobilis and may help to exploit the biotechnological applications of this industrially important bacterium.     

Development of sequential-co-culture system (Pichia stipitis and Zymomonas mobilis) for bioethanol production from Kans grass biomass

Sequential-co-culture technique was investigated in this study for the production of bioethanol from relatively cheaper lignocellulosic biomass of Kans grass (Saccharum spontaneum). The consortium of Pichia stipitis and Zymomonas mobilis was used to develop a suitable sequential-co-culture system. The Kans grass biomass was hydrolyzed in such a manner that the two sugar fractions, xylose rich and glucose rich were generated (a separate study). The P. stipitis cells and respective fermentation media (xylose rich) were fed to the fermentation vessel, after the set fermentation time Z. mobilis cells and respective media were fed to the same vessel. Different strategies have been followed and experiments were conducted initially at flask level. The selected strategy was then applied at bioreactor level using both synthetic fermentation media and Kans grass hydrolysate media to compare the kinetic parameters. The sequential addition of cultures with their respective media and imposed process conditions, showed better utilization of total sugars added (>95%). Microaerobic condition for P. stipitis and strictly anaerobic condition for Z. mobilis fermentation were found significant. The average ethanol yield (Y_p/s) and overall volumetric productivity (r_po) were found as 0.453 g_p/g_s and 1.580 g/l/h respectively for Kans grass hydrolysate media and 0.474 g_p/g_s and 2.901 g/l/h respectively for synthetic fermentation media.     

Isolation and identification of a novel Rhodococcus sp. ML-0004 producing epoxide hydrolase and optimization of enzyme production

Rhodococcus sp. ML-0004, a novel strain for producing epoxide hydrolase, was isolated from soil in this study. The epoxide hydrolase can catalyze the stereo-specific hydrolysis of cis-epoxysuccinic acid to generate l(+)-tartaric acid. By examining physiological, biochemical characteristics and comparing its 16S rDNA gene sequence, it was identified as Rhodococcus opacus, and named R. opacus ML-0004. The optimal conditions for epoxide hydrolase production from R. opacus ML-0004 were also investigated. Propanediol and (NH₄)₂SO₄ were selected as carbon source and nitrogen source, respectively, for the production of R. opacus ML-0004 epoxide hydrolase. The optimal conditions for epoxide hydrolase production were fermentation temperature = 28 °C, pH 7.0, and cultivation time = 26 h. Under these conditions, the maximum epoxide hydrolase activity reached 10.5 U mL⁻¹.     

Fast conversion of glycerol to 1,3-propanediol by a new strain of Klebsiella pneumoniae

Five bacterial strains screened from a batch of 39 samples could convert glycerol anaerobically to 1,3-propanediol (1,3-PD). One of the strains, XJ-Li, which could synthesize 1,3-PD with a higher concentration, was identified and characterized. Phylogenetic analysis of the strain XJ-Li included the study of morphology, physiological and biochemical characteristics. In addition, 16SrDNA sequences were created. The results indicated that this strain is a member of Klebsiella pneumoniae. The optimal cultivation parameters for pH and temperature were determined as 8.0 and 40 °C, respectively. The optimized nitrogen source and carbon source were 6.0 g/L of (NH₄)₂SO₄ and 20 g/L of glycerol, respectively. After 8 h in batch fermentation, both the 1,3-PD concentration and glycerol consumption reached the maximum, with 12.2 g/L of 1,3-PD and 1.53 g/L h of productivity, and a molar yield of 1,3-PD to glycerol of 0.75. Fed-batch fermentation also indicated a higher molar yield of 0.70, and the concentration of 1,3-PD reached 38.1 g/L after 66.4 g/L of glycerol consumption. The results of batch and fed-batch fermentations demonstrated that K. pneumoniae XJ-Li would be an excellent 1,3-PD producer.     

Enhanced production of insect raw-starch-digesting alpha-amylase accompanied by high erythritol synthesis in recombinant Yarrowia lipolytica fed-batch cultures at high-cell-densities

Recently we reported on raw-starch-digesting ability of alpha-amylase from an insect Sitophilus oryzae (SoAMY) expressed in recombinant Yarrowia lipolytica cells, and demonstrated its usefulness in simultaneous saccharification and fermentation processes with industrial yeasts. In this study we applied fed-batch cultures of Y. lipolytica 4.29 strain reaching high-cell-densities (up to 70 [g_DCW/L]), to enhance SoAMY production. SoAMY activity in the medium reached the peak value of 22,979.23 ± 184 [AU/L], at volumetric productivity of 121.58 ± 1.75 [AU/L/h], and yield of 71.83 ± 3.08 [AU/g_glycerol], constituting roughly 160-fold improvement, compared to the best previous result. The cultivations were accompanied by high production of erythritol (83.58 [g/L]), at the marginal production of mannitol (5.46 [g/L]). Elementary analyses of media constituents, the enzyme and the yeast biomass gave better insight into carbon and nitrogen fluxes distribution. Due to application of genetic engineering and bioprocess engineering strategies, the insect-derived enzyme can be produced at the quantities competitive to microbial catalysts.