Bacterial attachment to stainless steel welds: Significance of substratum microstructure

AISI Type 304 L stainless steel (SS) is a widely used material in industry due to its strength and resistance to corrosion. However, corrosion on SS is reported largely at welds or adjacent areas. Bacteria were observed to colonize preferentially near welds as a result of surface roughness. In the present study, the influence of another important metal surface condition on bacterial adhesion has been evaluated, i.e. substratum microstructure. Type 304 L SS weld samples were prepared and machined to separate weld metal, the heat affected zone (HAZ) and base metal regions. The coupons were molded in resin so that only the surfaces polished to a 3 p.m finish were exposed to the experimental medium with Pseudomonas sp. isolated from a corrosive environment in Japan. The coupons were exposed for varying durations. The area of bacterial attachment showed significant differences with time of exposure and; the type of coupons. Generally, the weld metal samples showed more attachment whilst the base metal showed the least. The area of attachment was inversely proportional to the average grain size of the three samples. As the bacteria started colonizing, attachment mainly occurred on the grain boundaries of the base metal (after 8h, 84.62% and 15.38% of the total number of bacteria attached in the field of view (FOV) at the grain boundary and matrix, respectively) and on the austenite‐ferrite interface in the weld metal (after 8h, 88.33% and 11.77% of the total number of bacteria attached in the FOV at the boundary and matrix, respectively). The weld area had more grains and hence more grain boundary/ unit area than the base metal, resulting in more bacterial attachment. SEM observations showed this increased attachment of Pseudomonas sp. resulted in the initiation of microbiologically influenced corrosion (MIC) on the weld coupons by 16 d. Therefore, the results provide data to support the fact that substratum microstructure influences bacterial attachment, which in turn leads to corrosion.     

Influence of carbon steel grade on the initial attachment of bacteria and microbiologically influenced corrosion

The influence of the composition and microstructure of different carbon steel grades on the initial attachment (≤ 60 min) of Escherichia coli and subsequent longer term (28 days) corrosion was investigated. The initial bacterial attachment increased with time on all grades of carbon steel. However, the rate and magnitude of bacterial attachment varied on the different steel grades and was significantly less on the steels with a higher pearlite phase content. The observed variations in the number of bacterial cells attached across different steel grades were significantly reduced by applying a fixed potential to the steel samples. Longer term immersion studies showed similar levels of biofilm formation on the surface of the different grades of carbon steel. The measured corrosion rates were significantly higher in biotic conditions compared to abiotic conditions and were found to be positively correlated with the pearlite phase content of the different grades of carbon steel coupons.     

Marine prosthecate bacteria involved in the ennoblement of stainless steel

Ennoblement, a phenomenon in which open-circuit potential is elevated to a noble value, triggers metal corrosion in the environment and is considered to be biologically catalysed. This study investigated the involvement of marine microorganisms in the ennoblement of stainless steel coupons in sea water pumped from Kamaishi Bay. Scanning electron microscopy (SEM) showed significant attachment of prosthecate bacteria on the surfaces of stainless steel coupons in the course of ennoblement. In denaturing gradient gel electrophoresis (DGGE) analyses of polymerase chain reaction-amplified bacterial 16S rDNA fragments, several major bands were detected from the surface of the ennobled coupons, including those affiliated with the alpha and gamma subclasses of the Proteobacteria. After these observations, bacterial strains were isolated from the surface of the ennobled coupon. The 16S rDNA analysis revealed that a bacterial isolate (designated PWB3) corresponded to a major DGGE band representing an alpha-Proteobacterial population; a database analysis showed that its closest relative was Rhodobium spp., albeit with low homology ( approximately 89%). SEM indicated that this bacterium was a prosthecate bacterium that was morphologically similar to those observed on the ennobled coupons. In pure culture of strain PWB3, stainless steel coupons were ennobled when the culture was supplemented with MnCl2. Manganese was recovered from the surface of the ennobled coupons after treatment with a reducing agent. These results suggest that the attachment of manganese-oxidizing prosthecate bacteria triggered the ennoblement of stainless steel in Kamaishi Bay sea water.     

The corrosion behaviour of galvanized steel in cooling tower water containing a biocide and a corrosion inhibitor

The corrosion behaviour of galvanized steel in cooling tower water containing a biocide and a corrosion inhibitor was investigated over a 10-month period in a hotel. Planktonic and sessile numbers of sulphate reducing bacteria (SRB) and heterotrophic bacteria were monitored. The corrosion rate was determined by the weight loss method. The corrosion products were analyzed by energy dispersive X-ray spectroscopy and X-ray diffraction. A mineralized, heterogeneous biofilm was observed on the coupons. Although a biocide and a corrosion inhibitor were regularly added to the cooling water, the results showed that microorganisms, such as SRB in the mixed species biofilm, caused corrosion of galvanized steel. It was observed that Zn layers on the test coupons were completely depleted after 3?months. The Fe concentrations in the biofilm showed significant correlations with the weight loss and carbohydrate concentration (respectively, p?<?0.01 and p?<?0.01).     

Microbial fouling community analysis of the cooling water system of a nuclear test reactor with emphasis on sulphate reducing bacteria

Culture and molecular-based techniques were used to characterize bacterial diversity in the cooling water system of a fast breeder test reactor (FBTR). Techniques were selected for special emphasis on sulphate-reducing bacteria (SRB). Water samples from different locations of the FBTR cooling water system, in addition to biofilm scrapings from carbon steel coupons and a control SRB sample were characterized. Whole genome extraction of the water samples and SRB diversity by group specific primers were analysed using nested PCR and denaturing gradient gel electrophoresis (DGGE). The results of the bacterial assay in the cooling water showed that the total culturable bacteria (TCB) ranged from 10(3) to 10(5)?cfu?ml(-1); iron-reducing bacteria, 10(3) to 10(5)?cfu?ml(-1); iron oxidizing bacteria, 10(2) to 10(3)?cfu?ml(-1) and SRB, 2-29?cfu?ml(-1). However, the counts of the various bacterial types in the biofilm sample were 2-3 orders of magnitude higher. SRB diversity by the nested PCR-DGGE approach showed the presence of groups 1, 5 and 6 in the FBTR cooling water system; however, groups 2, 3 and 4 were not detected. The study demonstrated that the PCR protocol influenced the results of the diversity analysis. The paper further discusses the microbiota of the cooling water system and its relevance in biofouling.     

Attachment of a pseudomonas sp. to Fe(III)‐(hydr)oxide surfaces

As a first step towards understanding microbial dissolution processes, our research focuses on characterizing attachment features that form between a Pseudomonas sp. bacteria and the Fe(III)‐(hydr)oxide minerals hematite and goethite. Microbial growth curves in Fe‐limited growth media indicated that the bacteria were able to obtain Fe from the Fe(III)‐(hydr)oxidesfor use in metabolic processes. A combination of scanning electron microscopy, epifluorescence, and Tapping Mode? atomic‐force microscopy showed that the bacteria colonized some fraction of mineralogical aggregates. These aggregates were covered by bacteria and were linked together by relatively open biofilms consisting of networks of fiber‐like attachment features intertwined through thin films of amorphous‐looking organic material. The biofilm material encompassed numerous individual bacteria, as well as minéralogie particles. We hypothesize that the bacteria first attached to mineral aggregates, perhaps via their flagella, forming colonies. Following initial attachment, the bacteria exuded additional attachment features in the form of fine, branching fibrils intertwined through thin films. The detailed structures of these attachment features were highlighted by Phase Imaging atomic‐force microscopy, which served as a real‐time contrast enhancement technique and showed some poorly defined sensitivity to different surface materials, most probably related to differences in stiffness or viscoelasticity. Although the mechanism of the microbially enhanced dissolution remains unknown, we hypothesize that the bacteria may have produced micro environments conducive to dissolution through the use of observed extracellular materials.     

Variation in sessile microflora as function of flow velocity on coupons exposed to seawater

The variability of several groups of microorganisms on AISI 1020 carbon steel coupons as a function of seawater velocity in a water circulation loop was investigated. The metal probes as well as electrodes were fixed onto ducts connected to a 35l capacity tank, in order to study both biofilm formation and some electrochemical parameters. The experiments were carried out at different seawater velocities. The technique of the most probable number was used to enumerate bacterial aerobes and anaerobes as well as sulphate-reducing bacteria and iron-reducing bacteria. Fungi were quantified by counting the number of colony forming units. At velocities of 3.6 cm/s, which correspond to a laminar flow, the numbers of aerobic and anaerobic bacteria attached to the metal surfaces reached a maximum. Such values were markedly reduced at velocities of 17.4–26.0 and 34.8 cm/s. The corrosion rate at the start of the process was 1.4 mm/year, decaying to levels of about 0.4–0.6 mm/year over the experimental period. Analysis of loss of carbon steel coupons mass after 35 days of the process indicated a mean corrosion rate of approximately 2 mm/year. This revised version was published online in November 2006 with corrections to the Cover Date.     

Metal corrosion by aerobic bacteria isolated from stimulated corrosion systems: Effects of additional nitrate sources

Many microorganisms are reported to influence the corrosive behaviour of mild steel and stainless steel in different habitats. In this study, 40 bacterial strains were isolated from corroded mild steel and stainless steel coupons in the nitrate supplemented environments. The corrosion abilities of the isolates against the mild steel and stainless steel coupons were tested with or without additional nitrate sources. The presence of bacterial isolates alone stimulated the corrosion of mild steel coupons. Most of the bio-corrosion processes of mild steel coupons were mitigated by adding nitrate supplement with bacterial isolates. The effects of bacterial isolates and additional nitrogen sources on corrosion of stainless steels were varied. Not all bacterial isolates stimulated the corrosion on stainless steel during the study period. Unlike the effects on mild steel coupons, additional NaNO₃ might stimulate, retard the corrosion rate by the bacterial isolates or have limited effects. Similar results were obtained when NH₄NO₃ was used. Phylogenetic analysis demonstrated that all isolates were closely related. The majority of the bacterial isolates from corroded metal coupons were identified as Bacillus species. Others were identified as Pseudomonas sp., Marinobacter sp., and Halomonas species. The results prove that the isolated aerobic microorganisms do play a role in the corrosion process of stainless and mild steel. Adding additional nitrate sources might be a tool to mitigate corrosion of mild steel which was stimulated by the presence of bacteria. However, to prevent the corrosion of stainless steels, it might need a trial and errors approach in each case.     

Nitrate treatment effects on bacterial community biofilm formed on carbon steel in produced water stirred tank bioreactor

To better understand the impact of nitrate in Brazilian oil reservoirs under souring processes and corrosion, the goal of this study was to analyse the effect of nitrate on bacterial biofilms formed on carbon steel coupons using reactors containing produced water from a Brazilian oil platform. Three independent experiments were carried out (E1, E2 and E3) using the same experimental conditions and different incubation times (5, 45 and 80 days, respectively). In every experiment, two biofilm-reactors were operated: one was treated with continuous nitrate flow (N reactor), and the other was a control reactor without nitrate (C reactor). A Polymerase Chain Reaction-Denaturing Gradient Gel Electrophoresis approach using the 16S rRNA gene was performed to compare the bacterial groups involved in biofilm formation in the N and C reactors. DGGE profiles showed remarkable changes in community structure only in experiments E2 and E3. Five bands extracted from the gel that represented the predominant bacterial groups were identified as Bacillus aquimaris, B. licheniformis, Marinobacter sp., Stenotrophomonas maltophilia and Thioclava sp. A reduction in the sulfate-reducing bacteria (SRB) most probable number counts was observed only during the longer nitrate treatment (E3). Carbon steel coupons used for biofilm formation had a slightly higher weight loss in N reactors in all experiments. When the coupon surfaces were analysed by scanning electron microscopy, an increase in corrosion was observed in the N reactors compared with the C reactors. In conclusion, nitrate reduced the viable SRB counts. Nevertheless, the nitrate dosing increased the pitting of coupons.     

Laser impact assessment in a biofilm-forming bacterium Pseudoalteromonas carrageenovora using a flow cytometric system

Impact by pulsed laser irradiations from an Nd:YAG laser on the marine biofilm-forming bacterium Pseudoalteromonas carrageenovora has been studied using a flow cytometric system. The biofilm-forming bacteria in the planktonic state have been irradiated while flowing, and the mortality and bacterial attachment have been determined by exposing TiN coupons in the system. Coupons suspended in the non-irradiated bacterial flow were treated as the control. The fluence used in the study was 0.1 J/cm(2). Three flow rates (14, 28, and 42 cm/min) and two exposure durations (15 and 30 min) were tested. The results showed the increase in bacterial mortality with the decrease in flow rate. The maximum mortality of 27.5% was observed when the flow rate was 14 cm/min. The bacterial attachment increased with the increase in flow rate and exposure duration. The area of bacterial attachment on the experimental coupons exposed to the irradiated sample was significantly lesser than that for the nonirradiated sample. The results thus show in a flowing system, low power pulsed laser irradiations could reduce the bacterial attachment even though it did not cause significant mortality.     

Establishment of callus and cell suspension cultures from Gypsophila paniculata leaf segments and study of the attachment of host cells by Erwinia herbicola pv. gypsophilae

Callus and cell suspension cultures were initiated from leaf segments of G. paniculata. Fresh and dry weights measurements of callus showed that callus growth was optimal on MS medium supplemented with 1.0 mg l^–1 2,4-dichlorophenoxyacetic acid (2,4-D) and 0.2 mg l^–1 benzyladenin (BA). Calli cultured on this medium, showed a two-fold increase in fresh weight by the fourth week of incubation. The initiated hard green callus was repeatedly subcultured on MS medium containing increasing concentrations of 2,4-D in order to increase its friability. The friable callus was then used for establishment of a cell suspension culture. Maximum growth of the suspension culture was on medium supplemented with 1.0 mg l^–1 2,4-D and 0.2 mg l^–1 BA.The suspension culture was used for studying plant host attachment in both electron and light microscopy. Upon infection with E. herbicola, plant cells showed aggregate formation within 24 h of infection. In the presence of the pathogenic Ehg,the number of aggregates formed was 342 aggregates ml^–1, in the presence of the non-pathogenic Ehg154 aggregates ml^–1 and in the control 115 aggregates ml^–1. These results show that the pathogenic strain causes formation of cell aggregates 5.8 times greater than the non-pathogenic one. Based on these results, it can be hypothesized that bacterial cells of the pathogenic strains bind to the plant cells and may form a bridge for attachment of plant cells to one another. Observations by electron microscope show that bacterial cells do attach to plant cells and that this attachment might be via formation of a bridge between the bacteria and the plant cell.     

The effects of disinfectant foam on microbial biofilms

This investigation examined the effects of common aqueous biocides and disinfectant foams derived from them on Pseudomonas aeruginosa biofilms. Biofilms were grown on stainless steel coupons under standardised conditions in a reactor supplemented with low concentrations of organic matter to simulate conditions prevalent in industrial systems. Five-day-old biofilms formed under ambient conditions with continuous agitation demonstrated a low coefficient of variation (5.809%) amongst viable biofilm bacteria from independent trials. Scanning electron microscopy revealed biofilms on coupons with viable biofilm bacteria observed by confocal microscopy. An aqueous solution of a common foaming agent amine oxide (AO) produced negligible effects on bacterial viability in biofilms (p?>?0.05). However, significant biofilm inactivation was noted with aqueous solutions of common biocides (peracetic acid, sodium hypochlorite, sodium ethylenediaminetetraacetic acid) with or without AO (p?<?0.05). Aereation of a mixture of AO with each of these common biocides resulted in significant reductions in the viability of biofilm bacteria (p?<?0.05). In contrast, limited effects were noted by foam devoid of biocides. A relationship between microbial inactivation and the concentration of biocide in foam (ranging from 0.1?–?0.5%) and exposure period were noted (p?<?0.05). Although, lower numbers of viable biofilm bacteria were recovered after treatment with the disinfectant foam than by the cognate aqueous biocide, significant differences between these treatments were not evident (p?>?0.05). In summary, the studies revealed significant biofilm inactivation by biocidal foam prepared with common biocides. Validation of foam disinfectants in controlled trials at manufacturing sites may facilitate developments for clean in place applications. Advantages of foam disinfectants include reductions in the volumes of biocides for industrial disinfection and in their disposal after use.     

Microbial Diversity at Iron-Clay Interfaces after 10 Years of Interaction Inside a Deep Argillite Geological Formation (Tournemire,France)

In the context of a geological disposal of radioactive waste in clayey formations, the consequences of microbial activity are of concern regarding the corrosion of metallic components. The purpose of the present work was to characterize the microbial diversity that may have impacted corrosion processes at the interface between re-compacted argillite and steel coupons after 10 years of interaction inside the Toarcian argillite layer in Tournemire (France) under in situ conditions. Several types of steel coupons were introduced in 1999 in two boreholes (so-called CR6 and CR8) drilled in the geological formation and filled with re-compacted argillite. CR6 borehole was drilled horizontally from a century-old railway tunnel and coupons were placed in the undisturbed argillite. CR8 borehole was drilled vertically under the tunnel, in conditions influenced by the draining of the Cernon fault water. CR6 and CR8 boreholes were overcored 10 years later and steel coupons as well as re-compacted argillite samples were analyzed separately. The characterization of their microbial diversity was carried out using culture media and molecular methods using 16S rRNA genes cloning. Data resulting from both approaches were complementary. Isolates and clone sequences were affiliated to only 3 bacterial phyla: Firmicutes, Actinobacteria and Proteobacteria. The biodiversities differed depending on the steel type and the borehole considered, indicating the influence of both iron-clay interactions and in situ environmental conditions. This analysis has highlighted the presence of sulphate-reducing bacteria, iron-reducing bacteria and isolates capable to develop at high temperatures. These microorganisms can grow at the interfaces between materials in a very short period of time compared with planned durations of disposal. Thus, these results should be considered to assess the consequences of microbial activities on the evolution of the metallic components like overpacks.     

Microbially influenced corrosion of galvanized steel pipes in aerobic water systems

Aims: To investigate the role of heterotrophic bacteria in the corrosion of galvanized steel in the presence of water. Methods and Results: Samples were taken from corroding galvanized steel pipes conveying water for specialist applications, and heterotrophic bacteria were isolated and cultured. The majority of bacteria were Gram‐negative aerobes and included Pseudomonas sp., Bacillus pumilus, Afipia spp. and Blastobacter denitrificans/Bradyrhizobium japonicum. Zinc tolerance was assessed through growth and zinc disc diffusion experiments. In general, zinc negatively influenced growth rates. An unidentified yeast also isolated from the system demonstrated a high tolerance to zinc at concentrations up to 4 g l^?1. Coupon experiments were performed to assess corrosion by the bacteria on galvanized steel and steel coupons. The majority of isolates as pure culture biofilms (69%) accelerated corrosion of galvanized coupons, assessed as zinc release, relative to sterile control coupons (P < 0·05). Pure culture biofilms did not increase the corrosion of steel, with four isolates demonstrating protective effects. Conclusions: Pure culture biofilms of heterotrophic bacteria isolated from a corroding galvanized pipe system were found to accelerate the corrosion of galvanized steel coupons. Significance and Impact of the Study: Microbially influenced corrosion is a potential contributor to sporadically occurring failures in galvanized steel systems containing water. Management strategies should consider microbial control as a means for corrosion prevention in these systems.     

Comparison of cell-specific activity between free-living and attached bacteria using isolates and natural assemblages

Marine snow aggregates are microbial hotspots that support high bacterial abundance and activities. We conducted laboratory experiments to compare cell-specific bacterial protein production (BPP) and protease activity between free-living and attached bacteria. Natural bacterial assemblages attached to model aggregates (agar spheres) had threefold higher BPP and two orders of magnitude higher protease activity than their free-living counterpart. These observations could be explained by preferential colonization of the agar spheres by bacteria with inherently higher metabolic activity and/or individual bacteria increasing their metabolism upon attachment to surfaces. In subsequent experiments, we used four strains of marine snow bacteria isolates to test the hypothesis that bacteria could up- and down-regulate their metabolism while on and off an aggregate. The protease activity of attached bacteria was 10-20 times higher than that of free-living bacteria, indicating that the individual strains could increase their protease activity within a short time (2 h) upon attachment to surfaces. Agar spheres with embedded diatom cells were colonized faster than plain agar spheres and the attached bacteria were clustered around the agar-embedded diatom cells, indicating a chemosensing response. Increased protease activity and BPP allow attached bacteria to quickly exploit aggregate resources upon attachment, which may accelerate remineralization of marine snow and reduce the downward carbon fluxes.     

Importance of biofilm formation for corrosion inhibition of SAE 1018 steel by axenic aerobic biofilms

To investigate if corrosion inhibition by aerobic biofilms is a general phenomenon, carbon steel (SAE 1018) coupons were exposed to a complex liquid medium (Luria–Bertani) and seawater-mimicking medium (VNSS) containing fifteen different pure-culture bacterial suspensions representing seven genera. Compared to sterile controls, the mass loss in the presence of these bacteria (which are capable of developing a biofilm to various degrees) decreased by 2- to 15-fold. The extent of corrosion inhibition in LB medium depended on the nature of the biofilm: an increased proportion of live cells, observed with confocal scanning laser microscopy (CSLM) and image analysis, decreased corrosion. Corrosion inhibition in LB medium was greatest with Pseudomonas putida (good biofilm formation), while metal coupons exposed to Streptomyces lividans in LB medium (poor biofilm formation) corroded in a manner similar to the sterile controls. Pseudomonas mendocina KR1 reduced corrosion the most in VNSS. It appears that only a small layer of active, respiring cells is required to inhibit corrosion, and the corrosion inhibition observed is due to the attached biofilm. Received 09 December 1996/ Accepted in revised form 19 March 1997     

Inhibition of bacterial attachment by pulsed Nd:YAG laser irradiations: an in vitro study using marine biofilm-forming bacterium Pseudoalteromonas carrageenovora

The effect of low mean power laser irradiations with short pulse duration from an Nd:YAG (neodymium-doped yttrium aluminium garnet) laser on a marine biofilm-forming bacterium, Pseudoalteromonas carrageenovora, was investigated in the laboratory. Laser-irradiated bacteria were tested for their ability to attach on nontoxic titanium nitride (TiN) coupons with nonirradiated bacteria as the reference. Two durations of irradiation were tested, 10 and 15 min. Bacterial attachment was monitored after 20 min, 40 min, and 1 h of irradiation. The average laser fluence used for this study was 0.1 J/cm(2). The area of attachment of the irradiated bacteria was significantly less than the reference for both durations of irradiation. The growth of irradiated bacteria showed a longer lag phase than the nonirradiated sample, mainly due to mortality in the former. The bacterial mortality observed was 23.4 +/- 0.71 and 48.6 +/- 6.5% for 10- and 15-min irradiations, respectively. Thus, the results show that low-power pulsed laser irradiations resulted in a significant bacterial mortality and a reduced bacterial attachment on nontoxic hard surfaces.     

Bacterial Degradation and Corrosion of Naphtha in Transporting Pipeline

Five naphtha hydrocarbon-degrading bacteria including representative strains of the two classified species (Serratia marcescensAR1, Bacillus pumilusAR2, Bacillus carboniphilus AR3, Bacillus megaterium AR4, and Bacillus cereus AR5) were identified by 16S rDNA gene sequence in a naphtha-transporting pipeline. The naphtha-degrading strains were able to be involved in the corrosion process of API 5LX steel and also utilized the naphtha as the sole carbon source. The biodegradation of naphtha by the bacterial isolates was characterized by gas chromatography-mass spectrometry. Weight-loss measurement on the corrosion of API 5LX steel in the presence/absence of consortia grown in naphtha-water aqueous media was performed. The scanning electron microscope observation showed that the consortia were able to attack the steel API 5LX surface, creating localized corrosion (pit). The biodegradation of naphtha by the strains AR1, AR2, AR3, AR4, and AR5 showed biodegradation efficiency of about 76.21, 67.20, 68.78, 68.78, and 68.15, respectively. The role of degradation on corrosion has been discussed. This basic study will be useful for the development of new approaches for the detection, monitoring, and control of microbial corrosion in a petroleum product pipeline.     

Antibiofilm effect of mono-rhamnolipids and di-rhamnolipids on carbon steel submitted to oil produced water

The objective of this study was to compare the potential of mono-rhamnolipids (mono-RML) and di-rhamnolipids (di-RML) against biofilm formation on carbon steel coupons submitted to oil produced water for 14 days. The antibiofilm effect of the RML on the coupons was analyzed by scanning electron microscopy (SEM) and by epifluorescence microscopy, and the contact angle was measured using a goniometer. SEM analysis results showed that all RML congeners had effective antibiofilm action, as well as preliminary anticorrosion evaluation confirmed that all RML congeners prevented the metal deterioration. In more detail, epifluorescence microscopy showed that mono-RML were the most efficient congeners in preventing microorganism's adherence on the carbon steel metal. Image analyses indicate the presence of 15.9%, 3.4%, and <0.1% of viable particles in di-RML, mono/di-RML and mono-RML pretreatments, respectively, in comparison to control samples. Contact angle results showed that the crude carbon steel coupon presented hydrophobic character favoring hydrophobic molecules adhesion. We calculated the theoretical polarity of the RML congeners and verified that mono-RML (log P = 3.63) presented the most hydrophobic character. This had perfect correspondence to contact angle results, since mono-RML conditioning (58.2°) more significantly changed the contact angle compared with the conditioning with one of the most common surfactants used on oil industry (29.4°). Based on the results, it was concluded that rhamnolipids are efficient molecules to be used to avoid biofilm on carbon steel metal when submitted to oil produced water and that a higher proportion of mono-rhamnolipids is more indicated for this application.     

Characterization of corrosive bacterial consortia isolated from petroleum-product-transporting pipelines

Microbiologically influenced corrosion is a problem commonly encountered in facilities in the oil and gas industries. The present study describes bacterial enumeration and identification in diesel and naphtha pipelines located in the northwest and southwest region in India, using traditional cultivation technique and 16S rDNA gene sequencing. Phylogenetic analysis of 16S rRNA sequences of the isolates was carried out, and the samples obtained from the diesel and naphtha-transporting pipelines showed the occurrence of 11 bacterial species namely Serratia marcescens ACE2, Bacillus subtilis AR12, Bacillus cereus ACE4, Pseudomonas aeruginosa AI1, Klebsiella oxytoca ACP, Pseudomonas stutzeri AP2, Bacillus litoralis AN1, Bacillus sp., Bacillus pumilus AR2, Bacillus carboniphilus AR3, and Bacillus megaterium AR4. Sulfate-reducing bacteria were not detected in samples from both pipelines. The dominant bacterial species identified in the petroleum pipeline samples were B. cereus and S. marcescens in the diesel and naphtha pipelines, respectively. Therefore, several types of bacteria may be involved in biocorrosion arising from natural biofilms that develop in industrial facilities. In addition, localized (pitting) corrosion of the pipeline steel in the presence of the consortia was observed by scanning electron microscopy analysis. The potential role of each species in biofilm formation and steel corrosion is discussed.