Halogen Engineering for Operationally Stable Perovskite Solar Cells via Sequential Deposition

The performance of perovskite solar cells (PSCs) relies on the synthesis method and chemical composition of the perovskite materials. So far, PSCs that have adopted two‐step sequential deposited perovskite with the state‐of‐art composition (FAPbI₃)_1?x(MAPbBr₃)_x (x < 0.05) have achieved record power conversion efficiency (PCE), while their one‐step antisolvent dripping counterparts with typical composition Cs_0.05FA_0.81MA_0.14Pb(I_0.85Br_0.15)₃ with more bromine have exhibited much better long‐term operational stability. Thus, halogen engineering that aims to elevate bromine content in sequential deposited perovskite film would push operational stability of PSCs toward that of antisolvent dripping deposited perovskite materials. Here, a Br‐rich seeding growth method is devised and perovskite seed solution with high bromine content is introduced into a PbI₂ precursor, leading to bromine incorporation in the resulting perovskite film. Photovoltaic devices fabricated by Br‐rich seeding growth method exhibit a PCE of 21.5%, similar to 21.6% for PSCs having lower bromine content. Whereas, the operational stability of PSCs with higher bromine content is significantly enhanced, with over 80% of initial PCE retained after 500 h tracking at maximum power point under 1‐sun illumination. This work highlights the vital importance of halogen composition for the operational stability of PSCs, and introduces an effective way to incorporate bromine into mixed‐cation‐halide perovskite film via sequential deposition method.     

Carrier Interfacial Engineering by Bismuth Modification for Efficient and Thermoresistant Perovskite Solar Cells

Organic–inorganic halide perovskite solar cells (PSCs) have emerged as attractive alternatives to conventional solar cells. It is still a challenge to obtain PSCs with good thermal stability and high permanence, especially at extreme outdoor temperatures. This work systematically studies the effects of Bi³⁺ modification on structural, electrical, and optical properties of perovskite films (FA_0.83MA_0.17Pb(I_0.83Br_0.17)₃) and the performance of corresponding PSCs. The results indicate that Bi³⁺ modified PSCs can achieve better thermal stability, photovoltaic response, and reproducibility compared with control cells due to the decreased grain boundaries, enhanced crystallization, and improved electron extraction from perovskite film. As a result, the modified PSC exhibits an optimized power conversion efficiency (PCE) of 19.4% compared with 18.3% for the optimized control device, accompanied by better thermoresistant ability under 100–180 °C and enhanced long‐term stability. The degradation rate of the modified device is reduced by an order of magnitude due to effective structural defect modification in perovskite photoactive layer. It could maintain more than two months at 60 °C. These results shed light on the origin of crystallization and thermal stability of perovskite films, and provide an approach to solve thermal stability issue of PSCs.     

Diammonium and Monoammonium Mixed‐Organic‐Cation Perovskites for High Performance Solar Cells with Improved Stability

Remarkable power conversion efficiencies (PCE) of metal–halide perovskite solar cells (PSCs) are overshadowed by concerns about their ultimate stability, which is arguably the prime obstacle to commercialization of this promising technology. Herein, the problem is addressed by introducing ethane‐1,2‐diammonium (⁺NH₃(CH₂)₂NH₃⁺, EDA²⁺) cations into the methyl ammonium (CH₃NH₃⁺, MA⁺) lead iodide perovskite, which enables, inter alia, systematic tuning of the morphology, electronic structure, light absorption, and photoluminescence properties of the perovskite films. Incorporation of <5 mol% EDA²⁺ induces strain in the perovskite crystal structure with no new phase formed. With 0.8 mol% EDA²⁺, PCE of the MAPbI₃‐based PSCs (aperture of 0.16 cm²) improves from 16.7% ± 0.6% to 17.9% ± 0.4% under 1 sun irradiation, and fabrication of larger area devices (aperture 1.04 cm²) with a certified PCE of 15.2% ± 0.5% is demonstrated. Most importantly, EDA²⁺/MA⁺‐based solar cells retain 75% of the initial performance after 72 h of continuous operation at 50% relative humidity and 50 °C under 1 sun illumination, whereas the MAPbI₃ devices degrade by approximately 90% within only 15 h. This substantial improvement in stability is attributed to the steric and coulombic interactions of embedded EDA²⁺ in the perovskite structure.     

Highly stable and Efficient Perovskite Solar Cells Based on FAMA‐Perovskite‐Cu:NiO Composites with 20.7% Efficiency and 80.5% Fill Factor

To solve critical issues related to device stability and performance of perovskite solar cells (PSCs), FA_0.026MA_0.974PbI_3?yCl_y‐Cu:NiO (formamidinium methylammonium (FAMA)‐perovskite‐Cu:NiO) and Al₂O₃/Cu:NiO composites are developed and utilized for fabrication of highly stable and efficient PSCs through fully‐ambient‐air processes. The FAMA‐perovskite‐Cu:NiO composite crystals prepared without using any antisolvents not only improve the perovskite film quality with large‐size crystals and less grain boundaries but also tailor optical and electronic properties and suppress charge recombination with reduction of trap density. A champion device based on the composites as light absorber and Al₂O₃/Cu:NiO interfacial layer between electron transport layer and active layer yields power conversion efficiency (PCE) of 20.67% with V_OC of 1.047 V, J_SC of 24.51 mA cm^?2, and fill factor of 80.54%. More importantly, such composite‐based PSCs without encapsulation show significant enhancement in long‐term air‐stability, thermal‐ and photostability with retaining 97% of PCE over 240 d under ambient conditions (25–30 °C, 45–55% humidity).     

Fusing Nanowires into Thin Films: Fabrication of Graded‐Heterojunction Perovskite Solar Cells with Enhanced Performance

Perovskite solar cells (PSCs) have recently experienced a rapid rise in power conversion efficiency (PCE), but the prevailing PSCs with conventional mesoscopic or planar device architectures still contain nonideal perovskite/hole‐transporting‐layer (HTL) interfaces, limiting further enhancement in PCE and device stability. In this work, CsPbBr₃ perovskite nanowires are employed for modifying the surface electronic states of bulk perovskite thin films, forming compositionally‐graded heterojunction at the perovskite/HTL interface of PSCs. The nanowire morphology is found to be key to achieving lateral homogeneity in the perovskite film surface states resulting in a near‐ideal graded heterojunction. The hidden role of such lateral homogeneity on the performance of graded‐heterojunction PSCs is revealed for the first time. The resulting PSCs show high PCE up to 21.4%, as well as high operational stability, which is superior to control PSCs fabricated without CsPbBr₃‐nanocrystals modification and with CsPbBr₃‐nanocubes modification. This study demonstrates the promise of controlled hybridization of perovskite nanowires and bulk thin films for more efficient and stable PSCs.     

Simultaneous Improved Performance and Thermal Stability of Planar Metal Ion Incorporated CsPbI2Br All‐Inorganic Perovskite Solar Cells Based on MgZnO Nanocrystalline Electron Transporting Layer

The high thermal stability and facile synthesis of CsPbI₂Br all‐inorganic perovskite solar cells (AI‐PSCs) have attracted tremendous attention. As far as electron‐transporting layers (ETLs) are concerned, low temperature processing and reduced interfacial recombination centers through tunable energy levels determine the feasibility of the perovskite devices. Although the TiO₂ is the most popular ETL used in PSCs, its processing temperature and moderate electron mobility hamper the performance and feasibility. Herein, the highly stable, low‐temperature processed MgZnO nanocrystal‐based ETLs for dynamic hot‐air processed Mn²⁺ incorporated CsPbI2Br AI‐PSCs are reported. By holding its regular planar “n–i–p” type device architecture, the MgZnO ETL and poly(3‐hexylthiophene‐2,5‐diyl) hole transporting layer, 15.52% power conversion efficiency (PCE) is demonstrated. The thermal‐stability analysis reveals that the conventional ZnO ETL‐based AI‐PSCs show a serious instability and poor efficiency than the Mg²⁺ modified MgZnO ETLs. The photovoltaic and stability analysis of this improved photovoltaic performance is attributed to the suitable wide‐bandgap, low ETL/perovskite interface recombination, and interface stability by Mg²⁺ doping. Interestingly, the thermal stability analysis of the unencapsulated AI‐PSCs maintains >95% of initial PCE more than 400 h at 85 °C for MgZnO ETL, revealing the suitability against thermal degradation than conventional ZnO ETL.     

Solvent Engineering Boosts the Efficiency of Paintable Carbon‐Based Perovskite Solar Cells to Beyond 14%

Carbon‐based hole transport material (HTM)‐free perovskite solar cells (PSCs) have shown much promise for practical applications because of their high stability and low cost. However, the efficiencies of this kind of PSCs are still relatively low, especially for the simplest paintable carbon‐based PSCs, in comparison with the organic HTM‐based PSCs. This can be imputed to the perovskite deposition methods that are not very suitable for this kind of devices. A solvent engineering strategy based on two‐step sequential method is exploited to prepare a high‐quality perovskite layer for the paintable carbon‐based PSCs in which the solvent for CH₃NH₃I (MAI) solution at the second step is changed from isopropanol (IPA) to a mixed solvent of IPA/Cyclohexane (CYHEX). This mixed solvent not only accelerates the conversion of PbI₂ to CH₃NH₃PbI₃ but also suppresses the Ostwald ripening process resulting in a high‐quality perovskite layer, e.g., pure phase, even surface, and compact capping layer. The paintable carbon‐based PSCs fabricated from IPA/CYHEX solvent exhibits a considerable enhancement in photovoltaic performance and performance reproducibility in comparison with that from pure IPA, especially on fill factor (FF), owing mainly to the better contact of perovskite/carbon interface, lower trap density in perovskite, higher light absorption ability, and faster charge transport of perovskite layer. As a result, the highest power conversion efficiency (PCE) of 14.38% is obtained, which is a record value for carbon‐based HTM‐free PSCs. Furthermore, a PCE of as high as 10% is achieved for the large area device (1 cm²), also the highest of its kind.     

Surface Electronic Modification of Perovskite Thin Film with Water‐Resistant Electron Delocalized Molecules for Stable and Efficient Photovoltaics

Although the efficiency of perovskite solar cells (PSCs) is close to crystalline silicon solar cells, the instability of perovskite, especially in humid condition, still hinders its commercialization. As an effective method to improve their stability, surface functionalization, by using hydrophobic molecules, has been extensively investigated, but usually accompanied with the loss of device efficiencies owing to their intrinsic electrical insulation. In this work, for the first time, it is demonstrated that 3‐alkylthiophene‐based hydrophobic molecules can be used as both water‐resistant and interface‐modified layers, which could simultaneously enhance both stability and performance significantly. Benefitting from their unique structures of thiophene rings, the π‐electrons are highly delocalized and thus enhance the charge transfer and collection at the interface. The device based on 3‐hexylthiophene treatment exhibits a champion energy conversion efficiency of 19.89% with a dramatic 10% enhancement compared with the pristine one (18.08%) of Cs_0.05 FA_0.81 MA_0.14 PbBr_0.45 I_2.55‐based PSCs. More importantly, the degradation of the long‐term efficiency of unsealed device is less than 20% in Cs_0.05 FA_0.81 MA_0.14 PbBr_0.45I_2.55‐based PSCs after more than 700 h storage in air. This finding provides an avenue for further improvement of both the efficiency and stability of PSCs.     

Extending the Continuous Operating Lifetime of Perovskite Solar Cells with a Molybdenum Disulfide Hole Extraction Interlayer

Solution‐processed organic–inorganic lead halide perovskite solar cells (PSCs) are considered as one of the most promising photovoltaic technologies thanks to both high performance and low manufacturing cost. However, a key challenge of this technology is the lack of ambient stability over prolonged solar irradiation under continuous operating conditions. In fact, only a few studies (carried out in inert atmosphere) already approach the industrial standards. Here, it is shown how the introduction of MoS₂ flakes as a hole transport interlayer in inverted planar PSCs results in a power conversion efficiency (PCE) of ≈17%, overcoming the one of the standard reference devices. Furthermore, this approach allows the realization of ultrastable PSCs, stressed in ambient conditions and working at continuous maximum power point. In particular, the photovoltaic performances of the proposed PSCs represent the current state‐of‐the‐art in terms of lifetime, retaining 80% of their initial performance after 568 h of continuous stress test, thus approaching the industrial stability standards. Moreover, it is further demonstrated the feasibility of this approach by fabricating large‐area PSCs (0.5 cm² active area) with MoS₂ as the interlayer. These large‐area PSCs show improved performance (i.e., PCE = 13.17%) when compared with the standard devices (PCE = 10.64%).     

Mixed Cation FAxPEA1–xPbI3 with Enhanced Phase and Ambient Stability toward High‐Performance Perovskite Solar Cells

In this work, different from the commonly explored strategy of incorporating a smaller cation, MA⁺ and Cs⁺ into FAPbI₃ lattice to improve efficiency and stability, it is revealed that the introduction of phenylethylammonium iodide (PEAI) into FAPbI₃ perovksite to form mixed cation FA_xPEA_1–xPbI₃ can effectively enhance both phase and ambient stability of FAPbI₃ as well as the resulting performance of the derived devices. From our experimental and theoretical calculation results, it is proposed that the larger PEA cation is capable of assembling on both the lattice surface and grain boundaries to form quais‐3D perovskite structures. The surrounding of PEA⁺ ions at the crystal grain boundaries not only can serve as molecular locks to tighten FAPbI₃ domains but also passivate the surface defects to improve both phase and moisture stablity. Consequently, a high‐performance (PCE:17.7%) and ambient stable FAPbI₃ solar cell could be developed.     

Structurally Reconstructed CsPbI2Br Perovskite for Highly Stable and Square‐Centimeter All‐Inorganic Perovskite Solar Cells

Although all‐inorganic perovskite solar cells (PSCs) demonstrate high thermal stability, cesium‐lead halide perovskites with high iodine content suffer from poor stability of the black phase (α‐phase). In this study, it is demonstrated that incorporating InCl₃ into the host perovskite lattice helps to inhibit the formation of yellow phase (δ‐phase) perovskite and thereby enhances the long‐term ambient stability. The enhanced stability is achieved by a strategy for the structural reconstruction of CsPbI₂Br perovskite by means of In³⁺ and Cl^? codoping, which gives rise to a significant improvement in the overall spatial symmetry with a closely packed atom arrangement due to the crystal structure transformation from orthorhombic (Pnma) to cubic (Pm‐3m). In addition, a novel thermal radiation heating method that further improves the uniformity of the perovskite thin films is presented. This approach enables the construction of all‐inorganic InCl₃:CsPbI₂Br PSCs with a champion power conversion efficiency of 13.74% for a small‐area device (0.09 cm²) and 11.4% for a large‐area device (1.00 cm²).     

Incorporating CsF into the PbI2 Film for Stable Mixed Cation‐Halide Perovskite Solar Cells

Adding a small amount of CsI into mixed cation‐halide perovskite film via a one‐step method has been demonstrated as an excellent strategy for high‐performance perovskite solar cells (PSCs). However, the one‐step method generally relies on an antisolvent washing process, which is hard to control and not suitable for fabricating large‐area devices. Here, CsF is employed and Cs is incorporated into perovskite film via a two‐step method. It is revealed that CsF can effectively diffuse into the PbI₂ seed film, and drastically enhances perovskite crystallization, leading to high‐quality Cs‐doped perovskite film with a very long photoluminescence carrier lifetime (1413 ns), remarkable light stability, thermal stability, and humidity stability. The fabricated PSCs show power conversion efficiency (PCE) of over 21%, and they are highly thermally stable: in the aging test at 60 °C for 300 h, 96% of the original PCE remains. The CsF incorporation process provides a new avenue for stable high‐performance PSCs.     

UV‐Inert ZnTiO3 Electron Selective Layer for Photostable Perovskite Solar Cells

Although planar‐structured perovskite solar cells (PSCs) have power conversion efficiencies exceeding 24%, the poor photostability, especially with ultraviolet irradiance (UV) severely limits commercial application. The most commonly‐used TiO₂ electron selective layer has a strong photocatalytic effect on perovskite/TiO₂ interface when TiO₂ is excited by UV light. Here a UV‐inert ZnTiO₃ is reported as the electron selective layer in planar PSCs. ZnTiO₃ is a perovskite‐structured semiconductor with excellent chemical stability and poor photocatalysis. Solar cells are fabricated with a structure of indium doped tin oxide (ITO)/ZnTiO₃/Cs_0.05FA_0.81MA_0.14PbI_2.55Br_0.45/Sprio‐MeOTAD/Au. The champion device exhibits a stabilized power conversion efficiency of 19.8% with improved photostability. The device holds 90% of its initial efficiency after 100 h of UV soaking (365 nm, 8 mW cm^?2), compared with 55% for TiO₂‐based devices. This work provides a new class of electron selective materials with excellent UV stability in perovskite solar cell applications.     

Long‐Lasting Nanophosphors Applied to UV‐Resistant and Energy Storage Perovskite Solar Cells

Recently, considerable progress is achieved in lab prototype perovskite solar cells (PSCs); however, the stability of outdoor applications of PSCs remains a challenge due to the high sensitivity of perovskite material under moist and ultraviolet (UV) light conditions. In this work, the UV photostability of PSC devices is improved by incorporating a photon downshifting layer—SrAl₂O₄: Eu²⁺, Dy³⁺ (SAED)—prepared using the pulsed laser deposition approach. Light‐induced deep trap states in the photoactive layer are depressed, and UV light‐induced device degradation is inhibited after the SAED modification. Optimized power conversion efficiency (PCE) of 17.8% is obtained through the enhanced light harvesting and reduced carrier recombination provided by SAED. More importantly, a solar energy storage effect due to the long‐persistent luminescence of SAED is obtained after light illumination is turned off. The introduction of downconverting material with long‐persistent luminescence in PSCs not only represents a new strategy to improve PCE and light stability by photoconversion from UV to visible light but also provides a new paradigm for solar energy storage.     

High‐Efficiency CsPbI2Br Perovskite Solar Cells with Dopant‐Free Poly(3‐hexylthiophene) Hole Transporting Layers

CsPbI₂Br is emerging as a promising all‐inorganic material for perovskite solar cells (PSCs) due to its more stable lattice structure and moisture resistance compared to CsPbI₃, although its device performance is still much behind this counterpart. Herein, a preannealing process is developed and systematically investigated to achieve high‐quality CsPbI₂Br films by regulating the nucleation and crystallization of perovskite. The preannealing temperature and time are specifically optimized for a dopant‐free poly(3‐hexylthiophene) (P3HT)‐based device to target dopant‐induced drastic performance degradation for spiro‐OMeTAD‐based devices. The resulting P3HT‐based device exhibits comparable power conversion efficiency (PCE) to spiro‐OMeTAD‐based devices but much enhanced ambient stability with over 95% PCE after 1300 h. A diphenylamine derivative is introduced as a buffer layer to improve the energy‐level mismatch between CsPbI₂Br and P3HT. A record‐high PCE of 15.50% for dopant‐free P3HT‐based CsPbI₂Br PSCs is achieved by alleviating the open‐circuit voltage loss with the buffer layer. These results demonstrate that the preannealing processing together with a suitable buffer layer are applicable strategies for developing dopant‐free P3HT PSCs with high efficiency and stability.     

SrTiO3/Al2O3‐Graphene Electron Transport Layer for Highly Stable and Efficient Composites‐Based Perovskite Solar Cells with 20.6% Efficiency

For practical use of perovskite solar cells (PSCs) the instability issues of devices, attributed to degradation of perovskite molecules by moisture, ions migration, and thermal‐ and light‐instability, have to be solved. Herein, highly efficient and stable PSCs based on perovskite/Ag‐reduced graphene oxide (Ag‐rGO) and mesoporous Al₂O₃/graphene (mp‐AG) composites are reported. The mp‐AG composite is conductive with one‐order of magnitude higher mobility than mp‐TiO₂ and used for electron transport layer (ETL). Compared to the mp‐TiO₂ ETL based cells, the champion device based on perovskite/Ag‐rGO and SrTiO₃/mp‐AG composites shows overall a best performance (i.e., V_OC = 1.057 V, J_SC = 25.75 mA cm^?2, fill factor (FF) = 75.63%, and power conversion efficiency (PCE) = 20.58%). More importantly, the champion device without encapsulation exhibits not only remarkable thermal‐ and photostability but also long‐term stability, retaining 97–99% of the initial values of photovoltaic parameters and sustaining ≈93% of initial PCE over 300 d under ambient conditions.     

2‐Thiopheneformamidinium‐Based 2D Ruddlesden–Popper Perovskite Solar Cells with Efficiency of 16.72% and Negligible Hysteresis

Formamidinium (FA)‐based 3D perovskite solar cells (PSCs) have been widely studied and they show reduced bandgap, enhanced stability, and improved efficiency compared to MAPbI₃‐based devices. Nevertheless, the FA‐based spacers have rarely been studied for 2D Ruddlesden–Popper (RP) perovskites, which have drawn wide attention due to their enormous potential for fabricating efficient and stable photovoltaic devices. Here, for the first time, FA‐based derivative, 2‐thiopheneformamidinium (ThFA), is successfully synthesized and employed as an organic spacer for 2D RP PSCs. A precursor organic salts‐assisted crystal growth technique is further developed to prepare high quality 2D (ThFA)₂(MA)_n?1Pb_nI_3n+1 (nominal n = 3) perovskite films, which shows preferential vertical growth orientations, high charge carrier mobilities, and reduced trap density. As a result, the 2D RP PSCs with an inverted planar p‐i‐n structure exhibit a dramatically improved power conversion efficiency (PCE) from 7.23% to 16.72% with negligible hysteresis, which is among the highest PCE in 2D RP PSCs with low nominal n‐value of 3. Importantly, the optimized 2D PSCs exhibit a dramatically improved stability with less than 1% degradation after storage in N₂ for 3000 h without encapsulation. These findings provide an effective strategy for developing FA‐based organic spacers toward highly efficient and stable 2D PSCs.     

Morphology Controlling of All‐Inorganic Perovskite at Low Temperature for Efficient Rigid and Flexible Solar Cells

All‐inorganic cesium lead halide (CsPbX₃) perovskites have emerged as promising photovoltaic materials owing to their superior thermal stability compared to traditional organic–inorganic hybrid counterparts. However, the CsPbX₃ perovskites generally need to be prepared at high‐temperature, which restricts their application in multilayer or flexible solar cells. Herein, the formation of CsPbX₃ perovskites at room‐temperature (RT) induced by dimethylsulphoxide (DMSO) coordination is reported. It is further found that a RT solvent (DMSO) annealing (RTSA) treatment is valid to control the perovskite crystallization dynamics, leading to uniform and void‐free films, and consequently a maximum power conversion efficiency (PCE) of 6.4% in the device indium tin oxide (ITO)/NiO _x /RT‐CsPbI₂Br/C₆₀/Bathocuproine (BCP)/Ag, which is, as far as it is known, the first report of RT solution‐processed CsPbX₃‐based perovskite solar cells (PSCs). Moreover, the efficiency can be boosted up to 10.4% by postannealing the RTSA‐treated perovskite film at an optimal temperature of 120 °C. Profiting from the moderate temperature, flexible PSCs are also demonstrated with a maximum PCE of 7.3% for the first time. These results may stimulate further development of all‐inorganic CsPbX₃ perovskites and their application in flexible electronics.     

Research Direction toward Scalable,Stable, and High Efficiency Perovskite Solar Cells

Discovery of the 9.7% efficiency, 500 h stable solid‐state perovskite solar cell (PSC) in 2012 triggered off a wave of perovskite photovoltaics. As a result, a certified power conversion efficiency (PCE) of 25.2% was recorded in 2019. Publications on PSCs have increased exponentially since 2012 and the total number of publications reached over 13 200 as of August 2019. PCE has improved by developing device structures from mesoscopic sensitization to planar p‐i‐n (or n‐i‐p) junction and by changing composition from MAPbI₃ to FAPbI₃‐based mixed cations and/or mixed anion perovskites. Long‐term stability has been significantly improved by interfacial engineering with hydrophobic materials or the 2D/3D concept. Although small area cells exhibit superb efficiency, scale‐up technology is required toward commercialization. In this review, research direction toward large‐area, stable, high efficiency PSCs is emphasized. For large‐area perovskite coating, a precursor solution is equally important as coating methods. Precursor engineering and formulation of the precursor solution are described. For hysteresis‐less, stable, and higher efficiency PSCs, interfacial engineering is one of the best ways as defects can be effectively passivated and thereby nonradiative recombination is efficiently reduced. Methodologies are introduced to minimize interfacial and grain boundary recombination.     

Lewis‐Adduct Mediated Grain‐Boundary Functionalization for Efficient Ideal‐Bandgap Perovskite Solar Cells with Superior Stability

State‐of‐the‐art perovskite solar cells (PSCs) have bandgaps that are invariably larger than 1.45 eV, which limits their theoretically attainable power conversion efficiency. The emergent mixed‐(Pb, Sn) perovskites with bandgaps of 1.2–1.3 eV are ideal for single‐junction solar cells according to the Shockley–Queisser limit, and they have the potential to deliver higher efficiency. Nevertheless, the high chemical activity of Sn(II) in these perovskites makes it extremely challenging to control their physical properties and chemical stability, thereby leading to PSCs with relatively low PCE and stability. In this work, the authors employ the Lewis‐adduct SnF₂·3FACl additive in the solution‐processing of ideal‐bandgap halide perovskites (IBHPs), and prepare uniform large‐grain perovskite thin films containing continuously functionalized grain boundaries with the stable SnF₂ phase. Such Sn(II)‐rich grain‐boundary networks significantly enhance the physical properties and chemical stability of the IBHP thin films. Based on this approach, PSCs with an ideal bandgap of 1.3 eV are fabricated with a promising efficiency of 15.8%, as well as enhanced stability. The concept of Lewis‐adduct‐mediated grain‐boundary functionalization in IBHPs presented here points to a new chemical route for approaching the Shockley–Queisser limit in future stable PSCs.