Improving the activity and stability of Yarrowia lipolytica lipase Lip2 by immobilization on polyethyleneimine-coated polyurethane foam

In this study, polyurethane foam (PUF) was used for immobilization of Yarrowia lipolytica lipase Lip2 via polyethyleneimine (PEI) coating and glutaraldehyde (GA) coupling. The activity of immobilized lipases was found to depend upon the size of the PEI polymers and the way of GA treatment, with best results obtained for covalent-bind enzyme on glutaraldehyde activated PEI-PUF (MW 70,000 Da), which was 1.7 time greater activity compared to the same enzyme immobilized without PEI and GA. Kinetic analysis shows the hydrolytic activity of both free and immobilized lipases on triolein substrate can be described by Michaelis–Menten model. The K_m for the immobilized and free lipases on PEI-coated PUF was 58.9 and 9.73 mM, respectively. The V_max values of free and immobilized enzymes on PEI-coated PUF were calculated as 102 and 48.6 U/mg enzyme, respectively. Thermal stability for the immobilization preparations was enhanced compared with that for free preparations. At 50 °C, the free enzyme lost most of its initial activity after a 30 min of heat treatment, while the immobilized enzymes showed significant resistance to thermal inactivation (retaining about 70% of its initial activity). Finally, the immobilized lipase was used for the production of lauryl laurate in hexane medium. Lipase immobilization on the PEI support exhibited a significantly improved operational stability in esterification system. After re-use in 30 successive batches, a high ester yield (88%) was maintained. These results indicate that PEI, a polymeric bed, could not only bridge support and immobilized enzymes but also create a favorable micro-environment for lipase. This study provides a simple, efficient protocol for the immobilization of Y. lipolytica lipase Lip2 using PUF as a cheap and effective material.     

Immobilization of acidic lipase derived from Pseudomonas gessardii onto mesoporous activated carbon for the hydrolysis of olive oil

Mesoporous activated carbon (MAC) derived from rice husk is used for the immobilization of acidic lipase (ALIP) produced from Pseudomonas gessardii. The purified acidic lipase had the specific activity and molecular weight of 1473 U/mg and 94 kDa respectively. To determine the optimum conditions for the immobilization of lipase onto MAC, the experiments were carried out by varying the time (10–180 min), pH (2–8), temperature (10–50 °C) and the initial lipase activity (49 × 10³, 98 × 10³, 147 × 10³ and 196 × 10³ U/l in acetate buffer). The optimum conditions for immobilization of acidic lipase were found to be: time—120 min; pH 3.5; temperature—30 °C, which resulted in achieving a maximum immobilization of 1834 U/g. The thermal stability of the immobilized lipase was comparatively higher than that in its free form. The free and immobilized enzyme kinetic parameters (K_m and V_max) were found using Michaelis–Menten enzyme kinetics. The K_m values for free enzyme and immobilized one were 0.655 and 0.243 mM respectively. The immobilization of acidic lipase onto MAC was confirmed using Fourier Transform-Infrared Spectroscopy, X-ray diffraction analysis and scanning electron microscopy.     

Hen egg white as a feeder protein for lipase immobilization

Enzyme stabilization via immobilization is one of the preferred processes as it provides the advantages of recovery and reusability. In this study, Thermomyces lanuginosus lipase has been immobilized through crosslinking using 2% glutaraldehyde and hen egg white, as an approach towards CLEA preparation. The immobilization efficiency and the properties of the immobilized enzyme in terms of stability to pH, temperature, and denaturants was studied and compared with the free enzyme. Immobilization efficiency of 56% was achieved with hen egg white. The immobilized enzyme displayed a shift in optimum pH towards the acidic side with an optimum at pH 4.0 whereas the pH optimum for free enzyme was at pH 6.0. The immobilized enzyme was stable at higher temperature retaining about 83% of its maximum activity as compared to the free enzyme retaining only 41% activity at 70 °C. The denaturation of lipase in free form was rapid with a half-life of 2 h at 60 °C and 58 min at 70 °C as compared to 12 h at 60 °C and 2 h at 70 °C for the immobilized enzyme. The effect of denaturants, urea and guanidine hydrochloride on the free and immobilized enzyme was studied and the immobilized enzyme was found to be more stable towards denaturants retaining 74% activity in 8 M urea and 98% in 6 M GndHCl as compared to 42% and 33% respectively in the case of free enzyme. The apparent K_m (2.08 mM) and apparent V_max (0.95 μmol/min) of immobilized enzyme was lower as compared to free enzyme; K_m (8.0 mM) and V_max (2.857 μmol/min). The immobilized enzyme was reused several times for the hydrolysis of olive oil.     

Ethyl isovalerate synthesis using Candida rugosa lipase immobilized on silica nanoparticles prepared in nonionic reverse micelles

Uniform and monodispersed silica nanoparticles were synthesized with a mean diameter of 100 ± 20 nm as analyzed by Transmission Electron Microscopy (TEM). Glutaraldehyde was used as a coupling agent for efficient binding of the lipase onto the silica nanoparticles. For the hydrolysis of pNPP at pH 7.2, the activation energy within 25–40 °C for free and immobilized lipase was 7.8 and 1.25 KJ/mol, respectively. The V_max and K_m of immobilized lipase at 25 °C for pNPP hydrolysis were found to be 212 μmol/min/mg and 0.3 mM, whereas those for free lipase were 26.17 μmol/min and 1.427 mM, respectively. The lower activation energy of immobilized lipase in comparison to free lipase suggests a change in conformation of the enzyme leading to a requirement for lower energy on the surface of the nanoparticles. A better yield (7 fold higher) of ethyl isovalerate was observed using lipase immobilized onto silica nanoparticles in comparison to free lipase.     

A comparative performance evaluation of jute and eggshell matrices to immobilize pancreatic lipase

A pancreatic lipase was immobilized on readily available and inexpensive jute and eggshell matrices. The purity of extracted enzyme was confirmed by SDS-PAGE. The maximum protein load for eggshell was 10.23 mg/g, and for jute, it was 5.7 mg/g. The free enzyme activity retention was greater than 80% for eggshell and 43% for jute. The immobilized lipase was stable over a pH range from 7 to 8 for eggshell and 7.5 to 8.5 for jute with over a temperature range from 25 to 45 °C for eggshell and 37 to 40 °C for the jute. FTIR data indicated new bonds on the jute upon immobilization. Although no new bond was observed, immobilization data on eggshell fit well with the Langmuir adsorption isotherm model. The model constants, Γ_max and K_l, were 13.92 mg/g and 0.382 mL/mg, respectively. Mixed adsorption with both ionic and hydrophobic interactions was observed. Lipase adsorption was reduced significantly in presence of Tween 80, whereas the effect was less in case of ionic strength, pH and temperature. For both matrices, scanning electron microscopy (SEM) was used to demonstrate the changes in surface morphology after immobilization. The performance of eggshell was better than that of jute as a matrix for immobilizing pancreatic lipase.     

Characterization of the lipase immobilized on Mg–Al hydrotalcite for biodiesel

Immobilization of Saccharomyces cerevisiae lipase by physical adsorption on Mg–Al hydrotalcite with a Mg/Al molar ratio of 4.0 led to a markedly improved performance of the enzyme. The immobilized lipase retained activity over wider ranges of temperature and pH than those of the free lipase. The immobilized lipase retained more than 95% relative activity at 50 °C, while the free lipase retained about 88%. The kinetic constants of the immobilized and free lipases were also determined. The apparent activation energies (E_a) of the free and immobilized lipases were estimated to be 6.96 and 2.42 kJ mol^?1, while the apparent inactivation energies (E_d) of free and immobilized lipases were 6.51 and 6.27 kJ mol^?1, respectively. So the stability of the immobilized lipase was higher than that of free lipase. The water content of the oil must be kept below 2.0 wt% and free fatty acid content of the oil must be kept below 3.5 mg KOH g [oil]^?1 in order to get the best conversion. This immobilization method was found to be satisfactory to produce a stable and functioning biocatalyst which could maintain high reactivity for repeating 10 batches with ester conversion above 81.3%.     

A novel method for the immobilization of glucoamylase onto polyglutaraldehyde-activated gelatin

A novel method was developed for the immobilization of glucoamylase from Aspergillus niger. The enzyme was immobilized onto polyglutaraldehyde-activated gelatin particles in the presence of polyethylene glycol and soluble gelatin, resulting in 85% immobilization yield. The immobilized enzyme has been fully active for 30 days. In addition, the immobilized enzyme retained 90 and 75% of its activity in 60 and 90 days, respectively. The enzyme optimum conditions were not affected by immobilization and the optimum pH and temperature for free and immobilized enzyme were 4 and 65 °C, respectively. The kinetic parameters for the hydrolysis of maltodextrin by free and immobilized glucoamylase were also determined. The K_m values for free and immobilized enzyme were 7.5 and 10.1 g maltodextrin/l, respectively. The V_max values for free and immobilized enzyme were estimated as 20 and 16 μmol glucose/(min μl enzyme), respectively. The newly developed method is simple yet effective and could be used for the immobilization of some other enzymes.     

Immobilization of fungal (Trametes versicolor) laccase onto Amberlite IR-120 H beads: Optimization and characterization

Laccase from Trametes versicolor was immobilized on Amberlite IR-120 H beads. Maximum immobilization obtained was 78.7% at pH = 4.5 and temperature T = 45 °C. Kinetic parameters, K_m and V_max values, were determined respectively as 0.051 mM and 2.77 × 10^?2 mM/s for free and 4.70 mM and 5.27 × 10^?3 mM/s for immobilized laccase. The Amberlite–laccase system showed a 30% residual activity after 7 cycles. On the other hand, the loss of activity for free laccase after 7 days of storage at 4 °C was 18.5% in comparison to Amberlite–laccase system with a loss of 1.4%, during the same period. Improved operational, thermal and storage stabilities of the immobilized laccase were obtained compared to the free counterpart. Therefore, the use of low-cost matrices, like Amberlite for enzyme immobilization represents a promising product for enzymatic industrial applications.     

Immobilization of Candida rugosa lipase on electrospun cellulose nanofiber membrane

A biocatalyst with high activity retention of lipase was fabricated by the covalent immobilization of Candida rugosa lipase on a cellulose nanofiber membrane. This nanofiber membrane was composed of nonwoven fibers with 200 nm nominal fiber diameter. It was prepared by electrospinning of cellulose acetate (CA) and then modified with alkaline hydrolysis to convert the nanofiber surface into regenerated cellulose (RC). The nanofiber membrane was further oxidized by NaIO₄. Aldehyde groups were simultaneously generated on the nanofiber surface for coupling with lipase. Response surface methodology (RSM) was applied to model and optimize the modification conditions, namely NaIO₄ content (2–10 mg/mL), reaction time (2–10 h), reaction temperature (25–35 °C) and reaction pH (5.5–6.5). Well-correlating models were established for the residual activity of the immobilized enzyme (R² = 0.9228 and 0.8950). We found an enzymatic activity of 29.6 U/g of the biocatalyst was obtained with optimum operational conditions. The immobilized lipase exhibited significantly higher thermal stability and durability than equivalent free enzyme.     

Immobilization of lipase on epoxy-activated Purolite® A109 and its post-immobilization stabilization

In this study, Purolite^® A109, polystyrenic macroporous resin, was used as immobilization support due to its good mechanical properties and high particle diameter (400 μm), which enables efficient application in enzyme reactors due to lower pressure drops. The surface of support had been modified with epichlorhydrine and was tested in lipase immobilization. Optimized procedure for support modification proved to be more efficient than conventional procedure for hydroxy groups (at 22 °C for 18 h), since duration of procedure was shortened to 40 min by performing modification at 52 °C resulting with almost doubled concentration of epoxy groups (563 μmol g⁻¹). Lipase immobilized on epoxy-modified support showed significantly improved thermal stability comparing to both, free form and commercial immobilized preparation (Novozym^® 435). The highest activity (47.5 IU g⁻¹) and thermal stability (2.5 times higher half-life than at low ionic strength) were obtained with lipase immobilized in high ionic strength. Thermal stability of immobilized lipase was further improved by blocking unreacted epoxy groups on supports surface with amino acids. The most efficient was treatment with phenylalanine, since in such a way blocked immobilized enzyme retained 65% of initial activity after 8 h incubation at 65 °C, while non-blocked derivative retained 12%.     

Development of a monolith based immobilized lipase micro-reactor for biocatalytic reactions in a biphasic mobile system

This paper reports a simple method for producing macroporous silica-monoliths with controllable porosity that can be used for the immobilization of lipases to generate an active and stable micro-reactor for biocatalysis. A range of commercially available lipases has been examined using the hydrolysis reactions of 4-nitrophenyl butyrate in water–decane media. The kinetic studies performed have identified that a similar value for k_cat is obtained for the immobilized Candida antarctica lipase A (0.13 min⁻¹) and the free lipase in solution (0.12 min⁻¹) whilst the immobilized apparent Michaelis constant K_m (3.1 mM) is 12 times lower than the free lipase in solution (38 mM). A 96% conversion was obtained for the immobilized C. antarctica lipase A compared to only 23% conversion for the free lipase. The significant higher conversions obtained with the immobilized lipases were mainly attributed to the formation of a favourable biphasic system in the continuous flowing micro-reactor system, where a significant increase in the interfacial activation occurred. The immobilized C. antarctica lipase A on the monolith also exhibited improved stability, showing 64% conversion at 80 °C and 70% conversion after continuous running for 480 h, compared to 40 and 20% conversions under the same temperature and reaction time for the free lipase.     

Immobilization of glucose oxidase onto cobalt based on silica core/shell nanoparticles as carrier

Co–B/SiO₂/NH₂ magnetic nanoparticles (NPs) were prepared from a silica shell-coated Co–B core using the Stöber method and amine-modification on the surface. Glucose oxidase (GOD) was covalently immobilized on the surface of Co–B/SiO₂/NH₂ NPs using N-(3-dimethylaminopropyl)-N′-ethylcarbodiimide (EDC) as an activating agent. The magnetic NPs characteristics, such as the synthesis of Co–B/SiO₂/NH₂ NPs, effect of pH, temperature, and concentration of buffer for enzyme immobilization, were investigated. The optimal reaction conditions for immobilization were determined to be 0.1 M of phosphate buffer solution, pH 7.0, and 5 °C. In the case of immobilized GOD without d-glucose and with 0.1 M of d-glucose for blocking, 22.98 U/g and 24.83 U/g of their original activity were retained after 7 reuses, respectively.     

Immobilization and characterization of human carbonic anhydrase I on amine functionalized magnetic nanoparticles

In this study, we synthesized magnetic nanoparticles (MNPs) by co-precipitation method. After that, silica coating with tetraethyl orthosilicate (TEOS) (SMNPs), amine functionalization of silica coated MNPs (ASMNPs) by using 3-aminopropyltriethoxysilane (APTES) were performed, respectively. After activation with glutaraldehyde (GA) of ASMNPs, human carbonic anhydrase (hCA I) was immobilized on ASMNPs. The characterization of nanoparticles was performed by transmission electron microscopy (TEM), fourier transform infrared spectroscopy (FT-IR), X-ray powder diffraction (XRD) and vibrating sample magnetometer (VSM). The immobilization conditions such as GA concentration, activation time of support with GA, enzyme amount, enzyme immobilization time were optimized. In addition of that, optimum conditions for activity, kinetic parameters (K_m, V_max, k_cat, kcat/K_m), thermal stability, storage stability and reusability of immobilized enzyme were determined.The immobilized enzyme activity was optimum at pH 8.0 and 25 °C. The K_m value of the immobilized enzyme (1.02 mM) was higher than the free hCA I (0.48 mM). After 40 days incubation at 4 °C and 25 °C, the immobilized hCA I sustained 89% and 85% of its activity, respectively. Also, it sustained 61% of its initial activity after 13 cycles. Such results revealed good potential of immobilized enzyme for various applications.     

Enhanced activity of immobilized pepsin nanoparticles coated on solid substrates compared to free pepsin

In the present work nanoparticles (NPs) of pepsin were generated in an aqueous solution using high-intensity ultrasound, and were subsequently immobilized on low-density polyethylene (PE) films, or on polycarbonate (PC) plates, or on microscope glass slides. The pepsin NPs coated on the solid surfaces have been characterized by HRSEM, TEM, FTIR, XPS and DLS. The amount of enzyme introduced on the substrates, the leaching properties, and the catalytic activity of the immobilized enzyme on the three surfaces are compared. Catalytic activities of pepsin deposited onto the three solid surfaces as well as free pepsin, without sonication, and free pepsin NPs were compared at various pH levels and temperatures using a hemoglobin assay. Compared to native pepsin, pepsin coated onto PE showed the best catalytic activity in all the examined parameters. Pepsin immobilized on glass exhibited better activity than the native enzyme, especially at high temperatures. Enzyme activity of pepsin immobilized on PC was no better than native enzyme activity at all temperatures at pH 2, and only over a narrow pH range at 37 °C was the activity improved over the native enzyme. A remarkable observation is that immobilized pepsin on all the surfaces was still active to some extent even at pH 7, while free pepsin was completely inactive. The kinetic parameters, K_m and V_max were also calculated and compared for all the samples. Relative to the free enzyme, pepsin coated PE showed the greatest improvement in kinetic parameters (K_m = 15 g/L, V_max = 719 U/mg versus K_m = 12.6 g/L and V_max = 787 U/mg, respectively), whereas pepsin coated on PC exhibited the most unfavorable kinetic parameters (K_m = 18 g/L, V_max = 685 U/mg). The values for the anchored enzyme-glass were K_m = 19 g/L, V_max = 763 U/mg.     

The study on effective immobilization of lipase on functionalized bentonites and their properties

Three different functionalized bentonites including acid activated bentonite (B_a), organically modified bentonite with cetyltrimethyl ammonium bromide (B_CTMAB) and the composite by acid activation and organo-modification (B_a-CTMAB) were prepared, and used for immobilization of lipase from bovine pancreatic lipase by adsorption. The amount of lipase adsorbed on the functionalized bentonites was in the following sequence: B_a > B_CTMAB > B_a-CTMAB, showing the strongest affinity of B_a for lipase among the three supports. However, the immobilized lipase on B_a-CTMAB showed the highest activity in the hydrolysis of olive oil by 1.67 times of activity of free lipase due to the hydrophobically interfacial activation and enlarged catalytic interface. While, the activity of immobilized lipase on B_a was lower than 20% of free lipase’s activity due to the absence of hydrophobic activation and negative impact of excessive hydrogen ions on the surface. The K_m values for the immobilized lipase on B_a-CTMAB (0.054 g/mL) and B_CTMAB (0.074 g/mL) were both lower than that of free lipase (0.115 g/mL), and the V_max values were higher for the immobilized lipases, exhibiting a higher affinity of the immobilized lipase toward olive oil than free lipase. In comparison to free lipase, the better resistance to heating inactivation, storage stability and reusability of the immobilized lipases on B_a-CTMAB and B_CTMAB were also obtained. The results show that the efficient and stable biocatalysts for industrial application can be prepared by using the low-cost bentonite mineral as the supports.     

Forming nanoparticles of α-amylase and embedding them into solid surfaces

In the current work nanoparticles (NPs) of α-amylase were generated in an aqueous solution using high-intensity ultrasound, and were subsequently immobilized on polyethylene (PE) films, or polycarbonate (PC) plates, or on microscope glass slides. The α-amylase NPs coated on the solid surfaces have been characterized by ESEM, TEM, FTIR, XPS and AFM. The substrates immobilized with α-amylase were used for hydrolyzing soluble potato starch to maltose. The amount of enzyme introduced in the substrates, leaching properties, and the catalytic activity of the immobilized enzyme were compared. The catalytic activity of the amylase deposited on the three solid surfaces was compared to that of the same amount of free enzyme at different pHs and temperatures. α-Amylase coated on PE showed the best catalytic activity in all the examined parameters when compared to native amylase, especially at high temperatures. When immobilized on glass, α-amylase showed better activity than the native enzyme over all pH and temperature values studied. However, the immobilization on PC did not improve the enzyme activity at any pH and any temperature compared to the free amylase. The kinetic parameters, K_m and V_max were also calculated. The amylase coated PE showed the most favorable kinetic parameters (K_m = 5 g L⁻¹ and V_max = 5E−07 mol mL⁻¹ min⁻¹). In contrast, the anchored enzyme-PC exhibited unfavorable kinetic parameters (K_m = 16 g L⁻¹, V_max = 4.2E−07 mol mL⁻¹ min⁻¹). The corresponding values for amylase-glass were K_m = 7 g L⁻¹, V_max = 1.8E−07 mol mL⁻¹ min⁻¹, relative to those obtained for the free enzyme (K_m = 6.6 g L⁻¹, V_max = 3.3E−07 mol mL⁻¹ min⁻¹).     

Lipase-catalyzed enantioselective acylation of 3-benzyloxypropane-1,2-diol in supercritical carbon dioxide

Lipase-catalyzed acylation of 3-benzyloxypropane-1,2-diol with vinyl acetate as acyl donor using different lipases [porcine pancreas lipase (PPL), Lipase AK “Amano”, Lipase PS “Amano”, and crude enzymes from Trichoderma reesei RUT-C30, Thermoascus thermophilus (NRRL5208), Talaromyces emersonii (NRLL3221)] was studied in supercritical carbon dioxide (scCO₂). In the reactions catalyzed by different lipases different amounts of monoacetate and diacetate products along with minor amounts of cyclic acetals forming from the diol and acetaldehyde were obtained.Application of Lipase AK led to the highest conversion (84.7%) and the highest enantiomeric excess values (ee_monoacetates = 38%, ee_diacetate = 85%). Effect of water content of scCO₂ on the productivity and the enantiomer selectivity of the reactions with Lipase AK was also investigated.     

Silanized palygorskite for lipase immobilization

Lipase from Candida lipolytica has been immobilized on 3-aminopropyltriethoxysilane-modified palygorskite support. Scanning electron micrographs proved the covalently immobilization of C. lipolytica lipase on the palygorskite support through glutaraldehyde. Using an optimized immobilization protocol, a high activity of 3300 U/g immobilized lipase was obtained. Immobilized lipase retained activity over wider ranges of temperature and pH than those of the free enzyme. The optimum pH of the immobilized lipase was at pH 7.0–8.0, while the optimum pH of free lipase was at 7.0. The retained activity of the immobilized enzyme was improved both at lower and higher pH in comparison to the free enzyme. The immobilized enzyme retained more than 70% activity at 40 °C, while the free enzyme retained only 30% activity. The immobilization stabilized the enzyme with 81% retention of activity after 10 weeks at 30 °C whereas most of the free enzyme was inactive after a week. The immobilized enzyme retains high activity after eight cycles. The kinetic constants of the immobilized and free lipase were also determined. The K_m and V_max values of immobilized lipase were 0.0117 mg/ml and 4.51 μmol/(mg min), respectively.     

Geranyl acetate synthesis catalyzed by Thermomyces lanuginosus lipase immobilized on electrospun polyacrylonitrile nanofiber membrane

Isolated Thermomyces lanuginosus lipase (TLL) was immobilized by different protocols on the polyacrylonitrile nanofibers membrane. The conditions for immobilization of TLL were optimized by investigating effect of protein concentration, time and temperature on the extent of immobilization. The effect of immobilization on the catalytic activity and stability of lipase was studied thoroughly. The immobilized TLL was used as biocatalyst for geranyl acetate synthesis with geraniol and vinyl acetate as substrates and their performance was compared with free enzyme. The TLL immobilized by physical adsorption shows higher transesterification and hydrolytic activities than that of covalently linked or native TLL. There was 32 and 9 fold increase in transesterification activity of TLL immobilized by adsorption and covalent bonding, while hydrolytic activity increases only by 3.6 and 1.8 fold respectively. The optimum conditions for immobilization in both the cases were immobilization time 90–150 min, temperature 45 °C and protein concentration of 2 mg/ml. The percentage conversion of ester was more than 90% and 66% in case of physically adsorbed and covalently bonded enzyme respectively as compared to native one. However, covalently immobilized TLL shows higher operational stability than native and physically adsorbed TLL.     

Optimization of immobilization conditions of Thermomyces lanuginosus lipase on styrene–divinylbenzene copolymer using response surface methodology

Microbial lipase from Thermomyces lanuginosus (formerly Humicola lanuginosa) was immobilized by covalent binding on a novel microporous styrene–divinylbenzene polyglutaraldehyde copolymer (STY–DVB–PGA). The response surface methodology (RSM) was used to optimize the conditions for the maximum activity and to understand the significance and interaction of the factors affecting the specific activity of immobilized lipase. The central composite design was employed to evaluate the effects of enzyme concentration (4–16%, v/v), pH (6.0–8.0), buffer concentration (20–100 mM) and immobilization time (8–40 h) on the specific activity. The results indicated that enzyme concentration, pH and buffer concentration were the significant factors on the specific activity of immobilized lipase and quadratic polynomial equation was obtained for specific activity. The predicted specific activity was 8.78 μmol p-NP/mg enzyme min under the optimal conditions and the subsequent verification experiment with the specific activity of 8.41 μmol p-NP/mg enzyme min confirmed the validity of the predicted model. The lipase loading capacity was obtained as 5.71 mg/g support at the optimum conditions. Operational stability was determined with immobilized lipase and it indicated that a small enzyme deactivation (12%) occurred after being used repeatedly for 10 consecutive batches with each of 24 h. The effect of methanol and tert-butanol on the specific activity of immobilized lipase was investigated. The immobilized lipase was almost stable in tert-butanol (92%) whereas it lost most of its activity in methanol (80%) after 15 min incubation.