Staining Mitochondria in Fixed Blood Smears

Wet blood smears are placed immediately in Helly's fluid for 24 hr, transferred directly to a saturated solution of potassium dichromate for 48 hr and washed in running water for 2-4 hr. The slides are then treated with iodine and sodium thiosulf ate and washed several hours or overnight. Excess water is removed by blotting the slide around the smear, Altmann's aniline fuchsin is placed on the smear and the slide is heated over a spirit lamp until white fumes appear. After the slide cools the stain is poured off and the excess removed by washing with distilled water. Methyl green (1% aqueous) is dropped on the smear and left for approximately 30 sec. It is then passed rapidly through 2 changes of absolute ethanol and into xylene, from which it is mounted in Permount. This stains mitochondria, red blood corpuscles and specific granules of eosinophilic granulocytes red on a green background.     

Concentrating and Staining Bone Marrow; An On-the-Slide Technique

A 0.5-1 ml sample of bone marrow is aspirated into a syringe containing 3 drops of 15% K₂-EDTA and an additional 1-2 drops of the EDTA solution previously placed on a slide, is then drawn into the syringe. All of the contents are ejected onto this slide, which is carefully tilted 2 or 3 times to an angle of 5-10°, and the edge brought to the center of another slide. The slide with the aspirate is then slowly tilted to 80-90°. Most of the blood and part of the marrow will drain off, leaving spicules of marrow and some blood on the original slide. A small drop of this concentrated marrow is dragged off with the edge of a third slide and deposited about 2 cm from the edge of a fourth slide on which the smear is to be made. The smear is made by bringing a clean (smearing) slide to the slide with the deposited marrow with flat surfaces parallel and the edges at a 90° angle. With gentle pressure, the smearing slide is pushed toward the empty end of the slide upon which the smear is made. This separates the marrow from the circulating blood. Before staining the smear is air dried and heated in an oven at 120-125 C for 2 min; or alternately for satisfactory but less uniform results the smear is heated over a microburner for 10 sec; then the smear is covered with 1 part of undiluted Wright's stain for 30—45 sec which is then diluted with 2 parts of a solution of 0.1-0.2 gm of Na₂S₂O₃ in 1 liter of distilled water and stained for 10-13 min with this diluted stain. Smears made in this manner have 3 concentric zones; the central zone contains the myeloid tissue; the middle, erythropoetic tissue; the outer, a mixture of blood and marrow.     

A Bacterial Cell Wall Stain1

A new method is given to stain bacterial cell walls, especially of Escherichia coli and Bacillus cereus. The cells are smeared in water on a slide and, as soon as air-dry, are stained 3-4 minutes with a 1 % aqueous solution of new fuchsin. The smear is washed with water until the stain ceases to run and is then allowed to air dry. The slide is placed on a 50°C. warm plate for 10-20 seconds, and the smear is then covered with a thin film of a 1-2% solution of Congo red at a pH of about 9.5. The smear is ready for observation as soon as dry or it may be washed with water if desired before observation.     

The Germination and Staining of Basidia in Gymnosporangium

A procedure is described for germinating and staining rust teliospores on the slide. The spores are germinated on slides in a damp chamber, about 3 hours being required for the production of sporidia. The material is killed by inverting slides over osmic acid fumes for a few minutes. Germinated spores are then allowed to dry on the slide, thus becoming fixed to the slide in a gelatin produced by the breaking down of their own stalks during germination. No other fixative is required. Material must be thoroly dehydrated in the alcohols (one or more hours in each of the higher alcohols); returned to water; mordanted for 2-3 hours in 4% iron alum; stained for 2-3 hours in 0.5% aqueous solution of Heidenhain's hematoxylin; destained in 2% iron alum. The material is passed back thru the alcohols and mixtures of xylol and absolute alcohol (1:2, 1:1, 2:1) to xylol and mounted in balsam. The method is particularly satisfactory for the Gymnosporanghim rusts, which have telia very readily gelatinized. The details of germination are preserved intact, as in nature, and many details of nuclear division are excellent.     

A Nuclear Stain for Escherichia Coli And Related Organisms

The dye base of new fuchsin was precipitated by adding potassium hydroxide to the dye solution. The precipitate was filtered out and washed with water. It was then suspended in water, brought into solution and adjusted to a pH of about 5.0 with nitric acid. The staining solution was prepared by adding 0.3 ml. of a 14% aqueous solution of pyrogallol and 0.1 ml. of a 1% aqueous solution of boric acid to 3.0 ml. of the dye solution. Smears of cells were made in water on a slide and allowed to dry before covering with the staining solution which was also permitted to air dry. The smear was then washed in water and mordanted for 5-20 seconds in a 0.1% aqueous solution of mercuric nitrate. After rinsing in water, the smear was air dried. When dry, the slide was placed on a 50° C. warm plate for a few seconds before covering with a very thin film of a 5% aqueous solution of nigrosin which had a pH of about 5.0.     

Differential Stain for acid fast Bacteria and Spores

A modified method of staining acid-fast organisms is described. After staining with carbol-fuchsin as usual in the Ziehl-Neelson method, wash with water and while the slide is still wet cover with a saturated acetone solution of malachite green for three to five minutes. Wash and examine. The acid-fast organisms and spores are red in a green background. If the smear is thick and appears too dense, dry for three minutes and hold over the mouth of a bottle of ammonia until decolorized to suit. Upon exposure to the air the green returns. This can be prevented by keeping the smear alkaline, by the addition of sodium bicarbonate.

A second method is described for use with sputum in which acid-fast organisms are scarce. It permits the examination of thick smears and therefore increases the chances of finding tubercle organisms when few in number. Stain with carbol fuchsin as in the Ziehl-Neelson method. Decolorize with 30% phenol-disulfonic acid in water for a few seconds or until decolorized. Wash and examine at once. If color returns upon washing decolorize again. The tubercle organisms appear red in a colorless background.     

Brilliant Cresyl Blue as a Stain for Plant Chromosomes

Methods are proposed for staining plant chromosomes with the dye brilliant cresyl blue, and for making these stained preparations permanent by using polyvinyl alcohol mounting medium.

The stain, which is composed of 2% brilliant cresyl blue in 45% aqueous acetic or propionic acid, is used with fixed material in making smear preparations. The technics for staining are similar to those employed in the aceto-carmine method.

The mounting medium is made by mixing 56% polyvinyl alcohol, which is diluted in water to the consistency of thick molasses, with 22% lactic acid and 22% phenol by volume. The permanent slides are made by floating off the cover slip of the temporary slide in 70% alcohol, then applying the mounting medium and replacing the cover slip.

The chief advantages of the methods described are:

1)The preparation of the stain is rapid and simple. The batch of stain will be good with the first try.

2)The staining procedure in some instances is shorter than when using aceto-carmine.

3)The stain shows a high degree of specificity for nuclear structures and gives better results than aceto-carmine when used on certain plant tissues.

4)A minimum number of cells is lost in making the slides permanent when using polyvinyl alcohol mounting medium as the slide and cover slip are run through only one solution prior to mounting.

5)The mounting medium dries rapidly and this shortens the time required before critical examination of the permanent mounts can be made.     

SpermBlue®: A new universal stain for human and animal sperm which is also amenable to automated sperm morphology analysis

Abstract

Our study was aimed at exploring a simple procedure to stain differentially the acrosome, head, midpiece, and flagellum of human and animal sperm. A further prerequisite was that sperm morphology of the stained samples could be analyzed using automated sperm morphology analysis (ASMA). We developed a new staining process using SpermBlue® fixative and SpermBlue® stain, which are iso-osmotic in relation to semen. The entire fixation and staining processes requires only 25 min. Three main steps are required. First, a routine sperm smear is made by either using semen or sperm in a diluting medium. The smear is allowed to air dry at room temperature. Second, the smear is fixed for 10 min by either placing the slide with the dried smear in a staining tray containing SpermBlue® fixative or by adding 1 ml SpermBlue® fixative to the slide. Third, the fixed smear is stained for 15 min by either immersing the slide in a staining tray containing SpermBlue® stain or adding four drops of SpermBlue® stain to the fixed smear. The stained slide is dipped gently in distilled water followed by air drying and mounting in DPX® or an equivalent medium. The method is simple and suitable for field conditions. Sperm of human, three monkey species, horse, boar, bull, ram, mouse, rat, domestic chicken, fish, and invertebrate species were stained successfully using the SpermBlue® staining process. SpermBlue® stains human and animal sperm different hues or intensities of blue. It is possible to distinguish clearly the acrosome, sperm head, midpiece, principal piece of the tail, and even the short end piece. The Sperm Class Analyzer® ASMA system was used successfully to quantify sperm head and midpiece measurements automatically at either 600 × or 1000 × magnification for most of the species studied.     

Preparation of Leaf Epidermis for Topographic Study

Epidermal strips of leaves of the Gramineae can be prepared using the following technique: The mature leaf is dipped in boiling water to kill the cells, and decolorized in boiling 70% alcohol. It is cleared and softened in 88% lactic acid. Epidermal, mesophyll and vascular tissue is removed from a selected constant area of the leaf leaving an epidermal strip 1-3 cm in length. This is inverted on a slide, stained in lactopheno-cotton blue, and destained in 88% lactic acid. Transverse and longitudinal sections of the strip are obtained at this stage. The epidermal strip is finally mounted on a slide in 88% lactic acid. The preparation is photographed with a 35 mm camera using transmitted light, and a yellow filter in the microscope lamp. Photomicrographs of known enlargement are then prepared from which accurate measurements can be recorded. The technique is applicable to both fresh and herbarium material.     

The Use of Acenaphthene in Pollen Tube Technic

A procedure is described for growing pollen tubes in such a manner that a large number of clearly analyzed figures can be obtained. The pollen grains are sown on an artificial medium of sugar, agar, gelatin, and water, the proportions of each varying with the species of pollen grain used. The medium is smeared on the slide while still hot to insure a thin covering, and the pollen grains are dusted on when the medium has sufficiently cooled and hardened. The slides are placed in a staining dish provided with slide slots and a cover, the inside of the cover and the bottom of the dish being lined with moist, but not wet, filter paper. Acenapthene crystals are lightly sprinkled on the bottom of the dish. The developing pollen tubes are thus exposed to the fumes given off by these crystals with consequent disturbance to the spindle mechanism. As a result, the chromosomes are not crowded on a metaphase plate but are widely separated in the tube facilitating any observations to be made.     

Restoration of broken cytology slides and creation of multiple slides from a single smear preparation.

A technique was developed for restoring broken cytology slides so that they are close to their original condition and for making multiple slides from a single smear preparation. The method is applicable to both cytologic preparations and histologic sections. In this study the fragmented smear preparation was treated with Pro-Texx, which penetrated, impregnated and solidified the full thickness of the pieces of the smear, enabling them to be lifted from the pieces of the broken slide. The removed pieces of the smear preparation were reassembled onto a new slide, which was then restained and coverslipped. In preparing multiple teaching slides, the treated smear preparation was divided as planned, with each portion mounted onto a separate slide, which was then restained and coverslipped. Ten other fine needle aspiration cases with broken slides have been restored, and more teaching slides were prepared from a single smear preparation using the same technique. All were equally successful. This technique provides an excellent method of smear transfer in cases of broken slides and creation of multiple slides from a single smear preparation for cytology teaching. This is particularly useful for unusual cases.     

A Method for Staining Certain Bacteria and Antherozoids

A modification of Loeffler's method for staining the flagella of bacteria was employed in staining large forms of bacteria and antherozoids. The bacteria or the antherozoids are killed and fixed in a drop of water on a slide and set aside to dry, before the next step is undertaken. The slide is treated for a period of time, varying from about ten minutes to several hours, in a practically saturated solution of tannic acid. After the slide is thoroly rinsed in water, it is stained with either a single stain or a combination of stains. The slide is then dehydrated with absolute alcohol, cleared, with clove oil, and completed in the usual manner.

The body of the bacterium and that of the antherozoid are well differentiated and the cilia are distinctly brought out by means of the method herein described.

The technic is of especial value in staining the antherozoids of mosses, liverworts, and ferns.     

A New and Rapid Method for Making Permanent Aceto-Carmin Smears

Smear the pollen mother cells of a single anther from each flower bud on a clean dry slide, using a small scalpel. Flood the slide with Belling's acetocarmin and heat for a second over an alcohol flame. Examine under the microscope to determine the stage of microsporogenesis. If the stage is satisfactory, smear the remaining anthers in the same manner, but fix and stain them by immediate immersion, face downward, in a petri dish full of hot (steaming) acetocarmin for from 1 to 10 minutes. Then rapidly transfer thru the following mixtures: two parts 99% (glacial) acetic acid plus one part absolute ethyl alcohol; one part acetic acid plus two parts absolute alcohol; and finally one part acetic acid plus nine parts absolute alcohol. The slides are then to be dehydrated completely by 1 to 2 minutes immersion in pure absolute alcohol, and cleared 2 to 3 minutes in a mixture of xylene and absolute alcohol in equal parts. The preparations are then made permanent by mounting each with balsam and a cover glass. The whole process takes from 5 to 15 minutes and is particularly recommended for chromosome counts.     

Sequential Use of Wright's and Ziehl-Neelsen's Stains for Demonstrating Phagocytosis of Bacterial Spores

Nongerminating spores, germinating spores, and vegetative cells of Clostridium botulinum type A were observed during phagocytosis in the peritoneal fluid of white mice. Since phagocytes are easily ruptured by heat, the method described avoids heating, as this has been employed in conventional spore staining methods. A thin smear of the fluid is air dried on the slide for 2 hr, and stained by Wright's method: stain, 2 min; dilution water, 2 min; and rinsed; then in 0.005% methylene blue for 30 sec, and rinsed. This is followed by Ziehl-Neelsen's stain for 3-4 min and destained with 1: acetone-95% ethanol for 10 sec. The slide is rinsed, and Wright's staining repeated: stain 1 min, dilution 2-3 min; and thereafter washed about 5 ml of Wright's buffer. Blotting and air drying completes the staining. Non-germinating spores stain light red with a red spore wall, germinating spores are deep red throughout, vegetative cells are blue, and leucocytes show a dark purple nucleus and light blue cytoplasm.     

A Quick-Freeze Method for Making Smear Slides Permanent

Many types of smear slides can be made permanent rapidly and effectively by substituting for the usual dehydration series a single-step process of freezing the slide on a block of dry ice, placing it immediately in 95% or absolute alcohol, and then mounting it. Advantages of the technic are its speed, the ease of separation of cover slip from slide with a minimum loss of cells, and the superiority of the resulting permanent slides.     

Simple Methods for Mammalian Chromosomes

The ordinary Feulgen-squash technic, after acetic-alcohol fixation, provides a simple and reliable method of preparing many mammalian tissues for chromosome counts. Tissues best suited to the technic were the seminiferous tubules. Small pieces of tissue about 3-6 mm. long and 1-2 mm. wide were immersed in a freshly made fixative (composed of 3 parts absolute ethyl alcohol and 1 part glacial acetic acid) immediately after removal by biopsy or from a freshly killed animal. After fixation for 3-12 hours the tissue was stained by the standard Feulgen procedure after hydrolysis for 12 minutes in normal HCl at 60 °C A 1-2 mm. piece was then teased apart on a slide in 45% acetic acid with a pair of mounted needles, and the teased tissue was squashed between the slide and the cover slip. During squashing the pressure was applied by hand and was regulated so as to avoid any excessive scattering of the chromosomes. The preparations were made permanent by dehydrating and mounting in Euparal.     

A substrate-film method for the histochemical demonstration of cellulase

Summary A substrate-film method has been devized for the histochemical demonstration of cellulase. The substrate film is made of sodium carboxymethyl-cellulose, which is made insoluble in water by fixation in acid ethanol. The tissue is briefly fixed in cold formalin, washed, and sectioned with a freezing microtome. The sections are mounted on slides, and covered with a piece of carboxymethyl-cellulose film, and the slide is incubated in a warm, moist atmosphere. After incubation, the film is stained with toluidine blue, and sites of cellulase activity appear as pale or clear patches in the film.In the digestive systems of certain molluscs, cellulase has been found in the lumens of the crop and stomach, and in the lumen and absorptive cells of the digestive gland tubules. The salivary glands, and the epithelia of the crop and stomach, show no reaction.Sections of control tissue, inactivated by boiling in water, do not show any reaction.I thank the Nobel Division of Imperial Chemical Industries Ltd. for information on their product Cellofas B 10, and for permission to publish that information.     

Techniques in the preparation of a monolayer of gynecologic cells for automated cytology. An overview

The computer-assisted microscope demands rigid specifications for specimen preparation. This paper addresses the variety of techniques developed by researchers attempting to automatically screen uterine cervical specimens. These same techniques could also be utilized for specimens from other body sites. In contrast to the easily prepared routine Papanicolaou smear, these techniques can be broken down into various steps as follows: transport media, cellular disaggregation, cell number estimation, cell separation and specimen enrichment, cellular adhesion to glass slide and cell transfer onto the slide. Variations on the theme are contrasted among specimen preparation methods utilized by prominent research groups. The plea for a simpler preparation method or, hopefully, utilization of the routine Papanicolaou smear for computer-assisted microscopy is made.     

A Modified Wright's Method for Staining Blood Smears

After the blood smear is treated for the proper length of time with Wright's stain, neutral distilled water is used for diluting the stain. After the slide has been treated with neutral distilled water until the smear becomes pinkish it is then treated with pure absolute methyl alcohol which destains the plasma. Neutral distilled water is again kept on the mount until the corpuscles are well stained. Then the slide is dehydrated with absolute ethyl alcohol, cleared with clove oil and completed in the usual way.

Blood smears of different groups of vertebrates were uniformly brilliantly stained with the above technic.

Several lots of Wright's dry stain have been tested with the modified technic and no difficulties have been encountered in its application.     

Some new methods for affixing sections to glass slides. II. Organic-solvent based adhesives

Adhesion of various organic-solvent based adhesives to glass slides could be greatly improved by first priming the slide with a copolymer of allyl methacrylate and methacryloxypropyltrimethoxysilane. The use of different solvents and types of adhesives with these slides is discussed. Cellulose nitrate in different esters of acetic acid proved to be an effective adhesive for varied sections at room temperature and in the cryostat. Carbowax sections as a special case preferably were affixed with polyisobutylene in petroleum ether. Most of the attachments formed resisted even boiling water.