Improvement of both lipid and biomass productivities of Qatar Chlorocystis isolate for biodiesel production and food security

Microalgae are considered a very promising alternative for biofuel production. Several strategies were developed to modulate and improve algae metabolites production to meet the requirements for biodiesel production. Most previous research evidenced that the increase of the lipid content is accompanied by a decrease of the biomass production, which increases the cost of the downstream processing. Hence, the challenge is to find special culture conditions that increase the lipid and the biomass productivities simultaneously. In the present work, we developed a strategy for the improvement of biomass and lipid productivities in a novel local microalga isolate, Chlorocystis sp. QUCCCM14, which was not previously known as a promising strain. Indeed, culturing QUCCCM14 using f/2 medium with 10× NaH₂PO₄ (0.15 g L^?1 NaNO₃ and 5.6 mg L^?1 NaH₂PO₄) resulted in an improvement of 3.178 folds the lipid productivity reaching 56.121 mg L^?1 day^?1 and enhanced the biomass productivity reaching 141.363 mg L^?1 day^?1, simultaneously. Comparative analyses of the FAME profiles demonstrated that fed‐batch culture with phosphate or nitrate separately leads to a high production of the omega 3 fatty acids (Linolenic acid), whereas fed‐batch culture with phosphate and nitrate simultaneously increased the production of fatty acids suitable for biodiesel production.     

Utilization of cane molasses towards cost-saving astaxanthin production by a Chlorella zofingiensis mutant

The aim of the present study was to survey the growth and astaxanthin production of E17, an astaxanthin-rich mutant of Chlorella zofingiensis, through feeding the low-cost carbon source cane molasses. In heterotrophic batch cultivation, E17 fed with pretreated molasses achieved biomass (1.79 g L^?1 day^?1) and astaxanthin (1.99 mg L^?1 day^?1) productivities comparable to those with glucose, which were about 2- and 2.8-fold of those fed with untreated molasses, respectively. Molasses-induced astaxanthin accumulation may be attributed to the elicited expression of carotenogenic genes, in particular the genes specifically responsible for the ketolation and hydroxylation of β-carotene to form astaxanthin. A two-stage fed-batch strategy was employed to grow E17 and induce astaxathin accumulation, resulting in 45.6 g L^?1 biomass and 56.1 mg L^?1 astaxanthin, the highest volumetric astaxanthin yield ever reported for this alga. In addition, the astaxanthin production by E17 was tested with a semi-continuous culture method, where the directly diluted raw molasses (giving 5 g L^?1 sugar) was used as the carbon source. Little growth inhibition of E17 was observed in the semi-continuous culture with a biomass productivity of 1.33 g L^?1 day^?1 and an astaxanthin productivity of 0.83 mg L^?1 day^?1. The mixotrophic semi-continuous cultures enhanced the biomass and astaxanthin productivities by 29.3 % and 42.2 %, respectively. This study highlights the potential of using the industrially cheap cane molasses towards large-scale cost-saving production of the high-value ketocarotenoid astaxanthin.     

Biomass and lipid enhancement in Ankistrodesmus sp. cultured with reused and minimal nutrients media

Microalgae are a promising feedstock for biofuel production. Lipid content in microalgae could be enhanced under nutrient depletion. This work investigated the effect of the nutrient on lipid accumulation in Ankistrodesmus sp. culture. Batch cultures were carried out using fresh BG11 medium, and after the harvest, the medium was reused for the next culture; this method was repeated two times. The maximum lipid productivity of 29.75 mg L^?1 day^?1 was obtained from the culture with the second reuse medium. In continuous cultures, Ankistrodesmus sp. was cultured in both fresh and modified BG11 mediums. The modified BG11 medium was adjusted to resemble the content of the first reuse medium. As a comparison between batch and continuous cultures, it was proven that the productivity in the continuous culture was better than in the batch, where the achievable maximum biomass and lipid were 188.30 and 38.32 mg L^?1 day^?1. The maximum lipid content of 34.22% was obtained from the continuous culture at a dilution rate of 0.08 day^?1, whereas the maximum saturated and unsaturated fatty acid productivities of 79.96 and 104.54 mg L^?1 day^?1 were obtained at a dilution rate of 0.16 day^?1.     

Repeated-batch production of kojic acid in a cell-retention fermenter using Aspergillus oryzae M3B9

A cell-retention fermenter was used for the pilot-scale production of kojic acid using an improved strain of Aspergillus oryzae in repeated-batch fermentations. Among the various carbon and nitrogen sources used, sucrose and yeast extract promoted pellet morphology of fungi and higher kojic acid production. Repeated-batch culture using a medium replacement ratio of 75% gave a productivity of 5.3 g L^–1 day^–1 after 11.5 days of cultivation. While batch culture in shake-flasks resulted in a productivity of 5.1 g L^–1 day^–1, a productivity of 5 g L^–1 day^–1 was obtained in a pilot-scale fermenter. By converting the batch culture into repeated batches, the non-productive downtime of cleaning, filling and sterilizing the fermenter between each batch were eliminated, thereby increasing the kojic acid productivity.     

Effect of mixed carbon substrate on exopolysaccharide production of cyanobacterium Nostoc flagelliforme in mixotrophic cultures

The effects of organic carbon sources on cell growth and exopolysaccharide (EPS) production of dissociated Nostoc flagelliforme cells under mixotrophic batch culture were investigated. After 7?days of cultivation, glycerol, acetate, sucrose, and glucose increased the final cell density and final EPS concentrations, and mixotrophic growth achieved higher biomass concentrations. The increase in cell growth was particularly high when glucose was added as the sole carbon source. On the other hand, EPS production per dry cell weight was significantly enhanced by adding acetate. For more effective EPS production, the effects of the mixture of glucose and acetate were investigated. Increasing the ratio of glucose to acetate resulted in higher growth rate with BG-11 medium and higher EPS productivity with BG-11₀ medium (without NaNO₃). When the medium was supplemented with a mixture of glucose (4.0?g?L^?1) and acetate (2.0?g?L^?1), 1.79?g?L^?1 biomass with BG-11 medium and 879.6?mg?L^?1 of EPS production with BG-11₀ medium were achieved. Adopting this optimal ratio of glucose to acetate established in flask culture, the culture was also conducted in a 20-L photobioreactor with BG-11 medium for 7?days. A maximum biomass of 2.32?g?L^?1 was achieved, and the EPS production was 634.6?mg?L^?1.     

Effects of carbon sources on growth and extracellular polysaccharide production of Nostoc flagelliforme under heterotrophic high-cell-density fed-batch cultures

Dissociated cells separated from a natural colony of Nostoc flagelliforme were cultivated heterotrophically in the darkness on glucose under fed-batch culture conditions. The effects of carbon sources (glucose, fructose, xylose, and sucrose) and concentrations on cell growth and extracellular polysaccharide (EPS) production were investigated. At harvest, the culture contained 1.325 g L^?1 of biomass and 117.2 mg L^?1 of EPS, respectively. The gravimetric EPS production rate was 16.7 mg g^?1 cell dry weight day^?1, which was 2.1 times higher than previously reported. Using sigmoid model, batch fermentation of N. flagelliforme was kinetically simulated to obtain equations including substrate consumption, biomass growth, and EPS accumulation. Results from a simulation correlated well with the experimental ones, indicating that this method could be useful in studying EPS production from batch and fed-batch cultures.     

Optimization of growth and production of toxins by three dinoflagellates in photobioreactor cultures

A bioreactor system for biotoxin production was appraised against traditional methods of growing dinoflagellate cultures. In an optimised bioreactor culture (5.4?L) operated in batch mode, growth of Karenia selliformis was more efficient than in 15-L bulk carboy culture in terms of growth rate (μ?=?0.07?day^?1 versus 0.05?day^?1) and growth maximum (G _max, 169.10⁶ versus 41.10⁶ cells L^?1). Maximal gymnodimine concentration (1200?μg L^?1) in bioreactor culture was 8-fold higher than in bulk carboy culture, and the yield per cell (pg cell^?1) was 2-fold higher. Similarly the bioreactor batch culture of Alexandrium ostenfeldii performed more efficiently than carboy cultures in terms of growth rate (1.6-fold higher), growth maximum (15-fold higher) and desmethyl C spirolide (SPX-desMe-C) yield (5-fold higher [μg L^?1], though the yield [pg cell^?1basis] was lower). When bioreactor cultures of K. selliformis were operated in continuous mode, the yield of gymnodimine was substantially higher than a carboy or the bioreactor run in batch mode to growth max (793?μg day^?1 over 58?days in continuous culture was achieved versus an average of 60?μg day^?1 [carboy over 40?days] or 249?μg day^?1 [batch mode] over 26?days). Likewise in continuous bioreactor cultures of A. ostenfeldii run over 25?days, the yield of SPX-desMe-C (29?μg day^?1) was substantially higher than in same cultures run in batch mode or carboys (10.2 day^?1 and 7.7?μg day^?1 respectively). Similarly 5.4?L bioreactor batch cultures of K. brevisulcata reached 3.8-fold higher cell densities than carboy cultures, and when operated in continuous mode, the brevisulcatic acids were more efficiently produced than in batch culture (12?μg day^?1 versus 7?μg day^?1). When the bioreactor system was upscaled to 52?L, the maximum cell densities and toxin yields of K. brevisulcata cultures were somewhat less than those achieved in the smaller reactor, which was attributed to reduced light penetration.     

Outdoor pilot-scale production of Botryococcus braunii in panel reactors

In this paper, the outdoor production of Botryococcus braunii in pilot-scale panel reactors (0.4?m³) is studied under uncontrolled conditions at a location close to the Atacama Desert (Chile). Discontinuous experiments were performed on different dates to determine the feasibility of the culture and the influence of environmental conditions on the system yield. Data showed that solar radiation is a major parameter in determining system yield, the average irradiance inside the culture determining both the growth rate and biomass productivity. A maximum specific growth rate of 0.09?day^?1 and biomass productivity of 0.02?g?L^?1?day^?1 (dry weight) were measured in discontinuous mode, at an average irradiance of 60?μE?m^?2?s^?1. With respect to lipids, a productivity of 2.5?mg?L^?1?day^?1 was obtained under favourable growth conditions; no accumulation of lipids at the stationary phase was observed. To confirm this behaviour, a semicontinuous culture was performed at 0.04?day^?1 in a larger reactor (1?m³). In this experiment, the biomass concentration and productivity was 0.3?g?L^?1 and 0.015?g?L^?1?day^?1, respectively. The lipid content and productivity was 15.6% and 2.4?mg?L^?1?day^?1, respectively, the mean average irradiance inside the reactor being 60?μmol photons?m^?2?s^?1. The light path of the reactor determines the light availability, thus determining also the biomass concentration and productivity of the reactor once the dilution rate is fixed. Experimentally, biomass productivity of 0.015?g?L^?1?day^?1 was determined for a light path of 0.15?m, but this can be increased by more than three times for a light path of 0.1?m. These data confirm that this alga can be produced outdoors in a secure form, the culture yield improving when optimal conditions are applied, the data reported here establishing the starting point for the development of the process.     

High‐pressure systems for gas‐phase free continuous incubation of enriched marine microbial communities performing anaerobic oxidation of methane

Novel high‐pressure biotechnical systems that were developed and applied for the study of anaerobic oxidation of methane (AOM) are described. The systems, referred to as high‐pressure continuous incubation system (HP‐CI system) and high‐pressure manifold‐incubation system (HP‐MI system), allow for batch, fed‐batch, and continuous gas‐phase free incubation at high concentrations of dissolved methane and were designed to meet specific demands for studying environmental regulation and kinetics as well as for enriching microbial biomass in long‐term incubation. Anoxic medium is saturated with methane in the first technical stage, and the saturated medium is supplied for biomass incubation in the second stage. Methane can be provided in continuous operation up to 20 MPa and the incubation systems can be operated during constant supply of gas‐enriched medium at a hydrostatic pressure up to 45 MPa. To validate the suitability of the high‐pressure systems, we present data from continuous and fed‐batch incubation of highly active samples prepared from microbial mats from the Black Sea collected at a water depth of 213 m. In continuous operation in the HP‐CI system initial methane‐dependent sulfide production was enhanced 10‐ to 15‐fold after increasing the methane partial pressure from near ambient pressure of 0.2 to 10.0 MPa at a hydrostatic pressure of 16.0 MPa in the incubation stage. With a hydraulic retention time of 14 h a stable effluent sulfide concentration was reached within less than 3 days and a continuing increase of the volumetric AOM rate from 1.2 to 1.7 mmol L^?1 day^?1 was observed over 14 days. In fed‐batch incubation the AOM rate increased from 1.5 to 2.7 and 3.6 mmol L^?1 day^?1 when the concentration of aqueous methane was stepwise increased from 5 to 15 mmol L^?1 and 45 mmol L^?1. A methane partial pressure of 6 MPa and a hydrostatic pressure of 12 MPa in manifold fed‐batch incubation in the HP‐MI system yielded a sixfold increase in the volumetric AOM rate. Over subsequent incubation periods AOM rates increased from 0.6 to 1.2 mmol L^?1 day^?1 within 26 days of incubation. No inhibition of biomass activity was observed in all continuous and fed‐batch incubation experiments. The organisms were able to tolerate high sulfide concentrations and extended starvation periods. Biotechnol. Bioeng. 2010; 105: 524–533. © 2009 Wiley Periodicals, Inc.     

Continuous multistep versus fed‐batch production of ethanol and xylitol in a simulated medium of sugarcane bagasse hydrolyzates

Co‐cultures for simultaneous production of ethanol and xylitol were studied under different operation bioreactor modes using Candida tropicalis IEC5‐ITV and Saccharomyces cerevisiae ITV01‐RD in a simulated medium of sugarcane bagasse hydrolyzates. Xylitol and ethanol tolerance by S. cerevisiae and C. tropicalis, respectively, was evaluated. The results showed that C. tropicalis was sensitive to ethanol concentrations up to 30 g/L, while xylitol had no effect on S. cerevisiae viability and metabolism. The best condition found for simultaneous culture was S. cerevisiae co‐culture and C. tropicalis sequential cultivation at 24 h. Under these conditions, productivity and yield for ethanol were Q_EtOH = 0.72 g L^?1 h^?1 and Y_EtOH/s = 0.37 g/g, and for xylitol, Q_XylOH = 0.10 g L^?1 h^?1 and Y_XylOH/S = 0.31 g/g, respectively; using fed‐batch culture, the results were Q_EtOH = 0.87 g L^?1 h^?1 and Y_EtOH/s = 0.44 g L^?1 h^?1, and Q_EtOH = 0.27 g L^?1 h^?1 and Y_EtOH/s = 0.57 g/g, respectively. Maximum volumetric productivity in continuous multistep cultures of ethanol and xylitol was at dilution rates of 0.131 and 0.074 h^?1, respectively. Continuous multistep production, Q_EtOH increased up to 50% more than in fed‐batch culture, even though xylitol yield remained unchanged.     

Biomass production of hairy roots of Artemisia annua and Arachis hypogaea in a scaled‐up mist bioreactor

Hairy roots have the potential to produce a variety of valuable small and large molecules. The mist reactor is a gas phase bioreactor that has shown promise for low‐cost culture of hairy roots. Using a newer, disposable culture bag, mist reactor performance was studied with two species, Artemisia annua L. and Arachis hypogaea (peanut), at scales from 1 to 20 L. Both species of hairy roots when grown at 1 L in the mist reactor showed growth rates that surpassed that in shake flasks. From the information gleaned at 1 L, Arachis was scaled further to 4 and then 20 L. Misting duty cycle, culture medium flow rate, and timing of when flow rate was increased were varied. In a mist reactor increasing the misting cycle or increasing the medium flow rate are the two alternatives for increased delivery of liquid nutrients to the root bed. Longer misting cycles beyond 2–3 min were generally deemed detrimental to growth. On the other hand, increasing the medium flow rate to the sonic nozzle especially during the exponential phase of root growth (weeks 2–3) was the most important factor for increasing growth rates and biomass yields in the 20 L reactors. A. hypogaea growth in 1 L reactors was µ = 0.173 day^?1 with biomass yield of 12.75 g DW L^?1. This exceeded that in shake flasks at µ = 0.166 day^?1 and 11.10 g DW L^?1. Best growth rate and biomass yield at 20 L was µ = 0.147 and 7.77 g DW L^?1, which was mainly achieved when medium flow rate delivery was increased. The mist deposition model was further evaluated using this newer reactor design and when the apparent thickness of roots (+hairs) was taken into account, the empirical data correlated with model predictions. Together these results establish the most important conditions to explore for future optimization of the mist bioreactor for culture of hairy roots. Biotechnol. Bioeng. 2010;107: 802–813. © 2010 Wiley Periodicals, Inc.     

Metabolic engineering of Escherichia coli for agmatine production

Agmatine is a kind of important biogenic amine. The chemical synthesis route is not a desirable choice for industrial production of agmatine. To date, there are no reports on the fermentative production of agmatine by microorganism. In this study, the base Escherichia coli strain AUX4 (JM109 ?speC ?speF ?speB ?argR) capable of excreting agmatine into the culture medium was first constructed by sequential deletions of the speC and speF genes encoding the ornithine decarboxylase isoenzymes, the speB gene encoding agmatine ureohydrolase and the regulation gene argR responsible for the negative control of the arg regulon. The speA gene encoding arginine decarboxylase harboured by the pKK223‐3 plasmid was overexpressed in AUX4, resulting in the engineered strain AUX5. The batch and fed‐batch fermentations of the AUX5 strain were conducted in a 3‐L bioreactor, and the results showed that the AUX5 strain was able to produce 1.13 g agmatine L^?1 with the yield of 0.11 g agmatine g^?1 glucose in the batch fermentation and the fed‐batch fermentation of AUX5 allowed the production of 15.32 g agmatine L^?1 with the productivity of 0.48 g agmatine L^?1 h^?1, demonstrating the potential of E. coli as an industrial producer of agmatine.     

Influence of carbon and nitrogen concentration on itaconic acid production by the smut fungus Ustilago maydis

Itaconic acid is a valuable platform compound for the production of bio‐based polymers, chemicals, and fuels. Ustilago maydis is a promising host for the production of itaconic acid from biomass‐derived substrates due to its unicellular growth pattern and its potential to utilize biomass‐derived sugar monomers and polymers. The potential of U. maydis for industrial itaconate production was assessed in pH‐controlled batch fermentations with varying medium compositions. Using 200 g/L glucose and 75 mM ammonium, 44.5 g/L of itaconate was produced at a maximum rate of 0.74 g L^?1 h^?1. By decreasing the substrate concentrations to 50 g/L glucose and 30 mM ammonium, a yield of 0.34 g/g (47 mol%) could be achieved. Itaconate production from xylose was also feasible. These results indicate that high itaconic acid titers can be achieved with U. maydis. However, further optimization of the biocatalyst itself through metabolic engineering is still needed in order to achieve an economically feasible process, which can be used to advance the development of a bio‐based economy.     

Screening and characterization of Isochrysis strains and optimization of culture conditions for docosahexaenoic acid production

Isochrysis is a genus of marine unicellular microalgae that produces docosahexaenoic acid (DHA, C22:6), a very long chain polyunsaturated fatty acid (PUFA) of significant health and nutritional value. Mass cultivation of Isochrysis for DHA production for human consumption has not been established due to disappointing low DHA productivity obtained from commonly used Isochrysis strains. In this study, 19 natural Isochrysis strains were screened for DHA yields and the results showed that the cellular DHA content ranged from 6.8 to 17.0 % of total fatty acids with the highest DHA content occurring in the exponential growth phase. Isochrysis galbana #153180 exhibited the greatest DHA production potential and was selected for further investigation. The effects of different light intensities, forms, and concentrations of nitrogen, phosphorus, and salinity on growth and DHA production of I. galbana #153180 were studied in a bubble column photobioreactor (PBR). Under favorable culture conditions, I. galbana #153180 contained DHA up to 17.5 % of total fatty acids or 1.7 % of cell dry weight. I. galbana #153180 was further tested in outdoor flat-plate PBRs varying in light path length, starting cell density (SCD), and culture mode (batch versus semicontinuous). When optimized, record high biomass and DHA productivity of I. galbana #153180 of 0.72 g L^?1?day^?1 and 13.6 mg?L^?1?day^?1, or 26.4 g?m^?2?day^?1 and 547.7 mg?m^?2?day^?1, respectively, were obtained, suggesting that I. galbana #153180 may be a desirable strain for commercial production of DHA.     

Effect of light emitting diodes on the cultivation of Spirulina platensis using NPK‐10:26:26 complex fertilizer

NPK‐10:26:26 complex fertilizer based culture medium was studied for the mass production of Spirulina platensis using different light emitting diodes (LEDs). First, cultivation was carried out under white LED to formulate the optimum fertilizer loading for which Spirulina growth was maximized. Optimum composition for newly formulated fertilizer medium was NPK fertilizer ?0.76 g L^?1 and sodium bicarbonate ?10.0 g L^?1 and corresponding biomass productivity was found to be 76.67 mg L^?1 day^?1. The effect of different LEDs (for example, blue, white, red, green and yellow) on Spirulina growth kinetics and the accumulation of chlorophyll, protein and lipid content was determined using the optimum NPK fertilizer medium. Kinetic parameters (i.e., biomass productivity, maximum specific growth rate, maximum biomass concentration, nitrogen‐to‐biomass conversion factor and phosphorus‐to‐biomass conversion factor) and chlorophyll accumulation were affected by the use of different LEDs and follow the following trend: blue > white > red > green > yellow, whereas protein and lipid accumulation was almost independent of LEDs used. Elemental C, N, P and K concentrations were measured to find the effects of nutrients for the growth of Spirulina platensis. Physicochemical parameters (pH and conductivity) were also monitored during biomass growth under different LEDs. Finally, biomass growth using NPK‐10:26:26 fertilizer under different LEDs was compared with standard Zarrouk medium and better growth results were obtained using optimally formulated NPK‐10:26:26 fertilizer medium.     

Modelling the growth and ethanol production of Brettanomyces bruxellensis at different glucose concentrations

Aim: To study the effect of glucose concentrations on the growth by Brettanomyces bruxellensis yeast strain in batch experiments and develop a mathematical model for kinetic behaviour analysis of yeast growing in batch culture. Methods and Results: A Matlab algorithm was developed for the estimation of model parameters. Glucose fermentation by B. bruxellensis was studied by varying its concentration (5, 9·3, 13·8, 16·5, 17·6 and 21·4%). The increase in substrate concentration up to a certain limit was accompanied by an increase in ethanol and biomass production; at a substrate concentration of 50–138 g l^?1, the ethanol and biomass production were 24, 59 and 6·3, 11·4 g l^?1, respectively. However, an increase in glucose concentration to 165 g l^?1 led to a drastic decrease in product formation and substrate utilization. Conclusions: The model successfully simulated the batch kinetic observed in all cases. The confidence intervals were also estimated at each phase at a 0·95 probability level in a t‐Student distribution for f degrees of freedom. The maximum ethanol and biomass yields were obtained with an initial glucose concentration of 138 g l^?1. Significance and Impact of the Study: These experiments illustrate the importance of using a mathematical model applied to kinetic behaviour on glucose concentration by B. bruxellensis.     

Heterotrophic high-cell-density fed-batch and continuous-flow cultures of <Emphasis Type="Italic">Galdieria sulphuraria</Emphasis> and production of phycocyanin

Production of biomass and phycocyanin (PC) were investigated in highly pigmented variants of the unicellular rhodophyte Galdieria sulphuraria, which maintained high specific pigment concentrations when grown heterotrophically in darkness. The parental culture, G. sulphuraria 074G was grown on solidified growth media, and intensely coloured colonies were isolated and grown in high-cell-density fed-batch and continuous-flow cultures. These cultures contained 80–110 g L⁻¹ biomass and 1.4–2.9 g L⁻¹ PC. The volumetric PC production rates were 0.5–0.9 g L⁻¹ day⁻¹. The PC production rates were 11–21 times higher than previously reported for heterotrophic G. sulphuraria 074G grown on glucose and 20–287 times higher than found in phototrophic cultures of Spirulina platensis, the organism presently used for commercial production of PC.     

Toward enhanced hyperforin production in St. John's wort root cultures

During the past decades, several trials targeted a stable, sustainable and economic production of St. John's wort (Hypericum perforatum) extract. The value of this extract stems from its use to treat depression and skin irritation due to its hyperforin content. Previously, hyperforin‐forming in vitro root cultures were established. Here, detailed growth and production kinetics have been analyzed over 40 days of cultivation. In the first 10 days, sucrose was completely hydrolyzed to glucose and fructose. The ammonium consumption supported the increase in the biomass and hyperforin production. When sucrose was replaced with glucose/fructose, the linear growth phase started 6 days earlier and resulted in a higher space‐time‐yield. The maximum hyperforin production was 0.82 mg L^?1 day^?1, which was 67 % higher than in the sucrose‐supplemented standard cultivation. Buffering the sucrose‐supplemented medium with phosphate caused a 2.7‐fold increase in the product to biomass yield coefficient. However, the combination of monosaccharides and buffering conditions did not cause an appreciable improvements in the production performance of the shake flask approaches. A potential scalability from flask to lab‐scale stirred bioreactors has been demonstrated. The results obtained offer a basis for a scalable production of hyperforin and a sustainable source for a tissue culture‐based phytomedicine.     

Photoautotrophic cultivating options of freshwater green microalgal Chlorococcum humicola for biomass and carotenoid production

Photoautotrophic cultivation of Chlorococcum humicola was performed in batch and continuous modes in different cultivating system arrangements to compare biomass and carotenoids’ concentration and their productivities. Batch result from stirred tank and airlift photobioreactors indicated the positive effect of increasing light intensity on growth and carotenoid production, whereas the finding from continuous cultivation indicated that carotenoid enhancement preferred high light intensity and nitrogen-deficient environment. The highest biomass (1.31?±?0.04?g?L^?1) and carotenoid (4.59?±?0.06?mg?L^?1) concentration as well as the highest productivities, 0.46?g?L^?1 d^?1 for biomass and 1.61?mg?L^?1 d^?1 for carotenoids, were obtained when maintaining high light intensity of 10 klx, BG-11 medium and 2% (v/v) CO₂ simultaneously, while the highest carotenoid content (4.84?mg?g^?1) was associated with high light intensity and nitrogen-deficient environment, which was induced by feed-modified BG-11 growth medium containing nitrate 20 folds lower than the original medium. Finally, the cultivating system arranged into smaller stirred tank photobioreactors in series yielded approximately 2.5 folds increase in both biomass and carotenoid productivities relative to using single airlift photobioreactor with equivalent working volume and similar operating condition.     

Chemostat production of pediocin SM‐1 by Pediococcus pentosaceus Mees 1934

Production of the bacteriocin pediocin SM‐1 by Pediococcus pentosaceus Mees 1934 was investigated in pH‐controlled batch and chemostat cultures using a complex medium containing glucose, sucrose or fructose. In chemostat cultures operated at 150 rpm, 30°C, 60% dissolved oxygen tension, pH 6.5, and D = 0.148 h^?1, the pediocin titer reached 185 AU/mL representing an increase of 32% compared with batch cultures in which glucose was used as the carbon source. Pediocin biosynthesis was markedly affected by the growth rate of the producer microorganism. For all carbon sources tested, pediocin production appeared to take place only at dilution rates lower than μ_max. However, only glucose supported production at the very low dilution rate of 0.05 h^?1 indicating a direct regulation of pediocin biosynthesis by the carbon source. Glucose supported higher biomass productivity and higher pediocin titers and yields compared with the other sugars used. © 2015 American Institute of Chemical Engineers Biotechnol. Prog., 31:1481–1486, 2015