Nanodiamond‐Embedded p‐Type Copper(I) Oxide Nanocrystals for Broad‐Spectrum Photocatalytic Hydrogen Evolution

Copper(I) oxide (Cu₂O) is an attractive photocatalyst because of its abundance, low toxicity, environmental compatibility, and narrow direct band gap, which allows efficient light harvesting. However, Cu₂O exhibits poor photocatalytic performance and photostability because of its short electron diffusion length and low hole mobility. Here, it is demonstrated that nanodiamond (ND) can greatly improve the photocatalytic hydrogen evolution reaction (HER) of the p‐type photocatalyst Cu₂O nanocrystals by nanocomposition. Compared with pure Cu₂O nanocrystals, this composite shows a tremendous improvement in HER performance and photostability. HER rates of 100.0 mg NDs‐Cu₂O nanocrystals are 1597 and 824 under the simulated solar light irradiation (AM 1.5, 100 mW cm^?2) and visible light irradiation (420–760 nm, 77.5 mW cm^?2), respectively. The solar‐to‐hydrogen conversion efficiency of this composite is 0.85%, which is nearly ten times higher than that of pure Cu₂O. The quantum efficiency of the composite is high, with values of 0.17% at and 0.23% at . The broad spectral response of ND provides numerous carriers for the subsequent reactions. The electron‐donating ability of ND and suitable band structures of the two components promote electron injection from ND to Cu₂O. These results suggest the broad applicability of ND to ameliorate the photoelectric properties of semiconductors.     

KVP2O7 as a Robust High‐Energy Cathode for Potassium‐Ion Batteries: Pinpointed by a Full Screening of the Inorganic Registry under Specific Search Conditions

Candidates for high‐energy cathodes in potassium‐ion batteries (KIBs) are selected by fully screening the inorganic compound structure database. The compounds that satisfy the specific conditions for plausible KIB cathodes are further subjected to theoretical and electrochemical verification, and KVP₂O₇ is finally pinpointed. KVP₂O₇ can reversibly desert/insert ≈60% of K⁺ (60 mA h g^?1) during either chemical or electrochemical oxidation/reduction. KVP₂O₇ shows an average discharge potential of ≈4.2 V versus K/K⁺, which corresponds to an energy density of 253 W h kg^?1 at 0.25 C. This high energy density characteristic of KVP₂O₇ is maintained both during fast charge/discharge (C/D) and prolonged redox cycles. The C/D of KVP₂O₇ is also accompanied by a phase transition between a monoclinic KVP₂O₇ (P2₁/c) and a triclinic K_1?xVP₂O₇. The structure interpretation of a new K_1?xVP₂O₇ phase indicates that K⁺‐extraction induces a conformational change of two tetrahedral PO₄ units in pyrophosphates. The phase of K_1?xVP₂O₇ (x ≈0.6) remains stable during the C/D process, although it returns to the inborn P2₁/c phase after thermal treatment. It is believed that the data‐mining protocol designed for this study will provide a new strategy for materials discovery and that the pinpointed KVP₂O₇ can be utilized as a reliable KIB cathode.     

Active Edge Sites Engineering in Nickel Cobalt Selenide Solid Solutions for Highly Efficient Hydrogen Evolution

An effective multifaceted strategy is demonstrated to increase active edge site concentration in Ni_0.33Co_0.67Se₂ solid solutions prepared by in situ selenization process of nickel cobalt precursor. The simultaneous control of surface, phase, and morphology result in as‐prepared ternary solid solution with extremely high electrochemically active surface area (C _dl = 197 mF cm^?2), suggesting significant exposure of active sites in this ternary compound. Coupled with metallic‐like electrical conductivity and lower free energy for atomic hydrogen adsorption in Ni_0.33Co_0.67Se₂, identified by temperature‐dependent conductivities and density functional theory calculations, the authors have achieved unprecedented fast hydrogen evolution kinetics, approaching that of Pt. Specifically, the Ni_0.33Co_0.67Se₂ solid solutions show a low overpotential of 65 mV at ?10 mV cm^?2, with onset potential of mere 18 mV, an impressive small Tafel slope of 35 mV dec^?1, and a large exchange current density of 184 µA cm^?2 in acidic electrolyte. Further, it is shown that the as‐prepared Ni_0.33Co_0.67Se₂ solid solution not only works very well in acidic electrolyte but also delivers exceptional hydrogen evolution reaction (HER) performance in alkaline media. The outstanding HER performance makes this solid solution a promising candidate for mass hydrogen production.     

A Dual‐Insertion Type Sodium‐Ion Full Cell Based on High‐Quality Ternary‐Metal Prussian Blue Analogs

Prussian blue analogs (PBAs) are especially investigated as superior cathodes for sodium‐ion batteries (SIBs) due to high theoretical capacity (≈170 mA h g^?1) with 2‐Na storage and low cost. However, PBAs suffer poor cyclability due to irreversible phase transition in deep charge/discharge states. PBAs also suffer low crystallinity, with considerable [Fe(CN)₆] vacancies, and coordinated water in crystal frameworks. Presently, a new chelating agent/surfactant coassisted crystallization method is developed to prepare high‐quality (HQ) ternary‐metal Ni_xCo_1?x[Fe(CN)₆] PBAs. By introducing inactive metal Ni to suppress capacity fading caused by excessive lattice distortion, these PBAs have tunable limits on depth of charge/discharge. HQ‐Ni_xCo_1?x[Fe(CN)₆] (x = 0.3) demonstrates the best reversible Na‐storage behavior with a specific capacity of ≈145 mA h g^?1 and a remarkably improved cycle performance, with ≈90% capacity retention over 600 cycles at 5 C. Furthermore, a dual‐insertion full cell on the cathode and NaTi₂(PO₄)₃ anode delivers reversible capacity of ≈110 mA h g^?1 at a current rate of 1.0 C without capacity fading over 300 cycles, showing promise as a high‐performance SIB for large‐scale energy‐storage systems. The ultrastable cyclability achieved in the lab and explained herein is far beyond that of any previously reported PBA‐based full cells.     

Stabilized Co3+/Co4+ Redox Pair in In Situ Produced CoSe2−x‐Derived Cobalt Oxides for Alkaline Zn Batteries with 10 000‐Cycle Lifespan and 1.9‐V Voltage Plateau

In aqueous alkaline Zn batteries (AZBs), the Co³⁺/Co⁴⁺ redox pair offers a higher voltage plateau than its Co²⁺/Co³⁺ counterpart. However, related studies are scarce, due to two challenges: the Co³⁺/Co⁴⁺ redox pair is more difficult to activate than Co²⁺/Co³⁺; once activated, the Co³⁺/Co⁴⁺ redox pair is unstable, owing to the rapid reduction of surplus Co³⁺ to Co²⁺. Herein, CoSe_2?x is employed as a cathode material in AZBs. Electrochemical analysis recognizes the principal contributions of the Co³⁺/Co⁴⁺ redox pair to the capacity and voltage plateau. Mechanistic studies reveal that CoSe_2?x initially undergoes a phase transformation to derived Co_xO_ySe_z, which has not been observed in other Zn//cobalt oxide batteries. The Se doping effect is conducive to sustaining abundant and stable Co³⁺ species in Co_xO_ySe_z. As a result, the battery achieves a 10 000‐cycle ultralong lifespan with 0.02% cycle^?1 capacity decay, a 1.9‐V voltage plateau, and an immense areal specific capacity compared to its low‐valence oxide counterparts. When used in a quasi‐solid‐state electrolyte, as‐assembled AZB delivers 4200 cycles and excellent tailorability, a promising result for wearable applications. The presented effective strategy for obtaining long‐cyclability cathodes via a phase transformation‐induced heteroatom doping effect may promote high‐valence metal species mediation toward highly stable electrodes.     

Impact of Hydroxylation and Hydration on the Reactivity of α‐Fe2O3 (0001) and (102) Surfaces under Environmental and Electrochemical Conditions

Hematite (α‐Fe₂O₃) is widely used as a catalytic electrode material in photo‐electrochemical water oxidation, where its surface compositions and stabilities can strongly impact the redox reaction process. Here, its surface configurations in environmental or electrochemical conditions are assessed via density functional theory (DFT) calculations conducted at the Perdew, Burke, and Ernzerhof (PBE)+U level. The most energetically favorable surface domains of α‐Fe₂O₃ (0001) and (102) are predicted by constructing the surface phase diagrams in the framework of first‐principle thermodynamics. The relative surface stabilities are investigated as a function of partial pressures of oxygen and water, temperature, solution pH, and electrode potential not only for perfect bulk terminations but also for defect‐containing surfaces having various degrees of hydroxylation and hydration. In order to assess the impact on the redox reactions of the surface planes as well as of the extent of surface hydration/hydroxylation, the thermodynamics of the four‐step oxygen evolution reaction (OER) mechanism are examined in detail for different models of the α‐Fe₂O₃ (0001) and (102) surfaces. Importantly, the results underline that the nature of the surface termination and the degree of near‐surface hydroxylation give rise to significant variations in the OER overpotentials.     

Self‐Assemble and In Situ Formation of Ni1−xFexPS3 Nanomosaic‐Decorated MXene Hybrids for Overall Water Splitting

Herein, the authors present the development of novel 0D–2D nanohybrids consisting of a nickel‐based bimetal phosphorus trisulfide (Ni_1?xFe_xPS₃) nanomosaic that decorates on the surface of MXene nanosheets (denoted as NFPS@MXene). The nanohybrids are obtained through a facile self‐assemble process of transition metal layered double hydroxide (TMLDH) on MXene surface; followed by a low temperature in situ solid‐state reaction step. By tuning the Ni:Fe ratio, the as‐synthesized NFPS@MXene nanohybrids exhibit excellent activities when tested as electrocatalysts for overall water splitting. Particularly, with the initial Ni:Fe ratio of 7:3, the obtained Ni_0.7Fe_0.3PS₃@MXene nanohybrid reveals low overpotential (282 mV) and Tafel slope (36.5 mV dec^?1) for oxygen evolution reaction (OER) in 1 m KOH solution. Meanwhile, the Ni_0.9Fe_0.1PS₃@MXene shows low overpotential (196 mV) for the hydrogen evolution reaction (HER) in 1 m KOH solution. When integrated for overall water splitting, the Ni_0.7Fe_0.3PS₃@MXene || Ni_0.9Fe_0.1PS₃@MXene couple shows a low onset potential of 1.42 V and needs only 1.65 V to reach a current density of 10 mA cm^?2, which is better than the all noble metal IrO₂ || Pt/C electrocatalyst (1.71 mV@10 mA cm^?2). Given the chemical versatility of Ni_1?xFe_xPS₃ and the convenient self‐assemble process, the nanohybrids demonstrated in this work are promising for energy conversion applications.     

Reduced Nonradiative Energy Loss Caused by Aggregation of Nonfullerene Acceptor in Organic Solar Cells

Reducing energy loss (E_loss) is of critical importance to improving the photovoltaic performance of organic solar cells (OSCs). Although nonradiative recombination ( $E_{\mathrm{loss}}^{\mathrm{nonrad}}$) is investigated in quite a few works, the method for modulating $E_{\mathrm{loss}}^{\mathrm{nonrad}}$ is seldom reported. Here, a new method of depressing E_loss is reported for nonfullerene OSCs. In addition to ternary‐blend bulk heterojunction (BHJ) solar cells, it is proved that a small molecular material (NRM‐1) can be selectively dispersed into the acceptor phase in the PBDB‐T:IT‐4F‐based OSC, resulting in lower $E_{\mathrm{loss}}^{\mathrm{rad}}$ and $E_{\mathrm{loss}}^{\mathrm{nonrad}}$, and hence a significant improvement in the open‐circuit voltage (V_OC); under an optimal feed ratio of NRM‐1, an enhanced power conversion efficiency can also be gained. Moreover, the role of NRM‐1 in the method is illustrated and its applicability for several other representative OSCs is validated. This work paves a new pathway to reduce the E_loss for nonfullerene OSCs.     

Integrating Band Structure Engineering with All‐Scale Hierarchical Structuring for High Thermoelectric Performance in PbTe System

PbTe_1?x Se_x ‐2%Na‐y%SrTe system is investigated and a high maximum ZT of 2.3 at 923 K for PbTe_0.85Se_0.15‐2%Na‐4%SrTe is reported. This is achieved by performing electronic band structures modifications as well as all‐scale hierarchical structuring and combining the two effects. It is found that high ZTs in PbTe_0.85Se_0.15‐2%Na‐4%SrTe are possible at all temperature from 300 to 873 K with an average ZT_ave of 1.23. The high performance in PbTe_1?x Se_x ‐2%Na‐y%SrTe can be achieved by either choosing PbTe‐2Na‐4SrTe or PbTe_0.85Se_0.15‐2Na as a matrix. At room temperature the carrier mobility shows negligible variations as SrTe fraction is increased, however the lattice thermal conductivity is significantly reduced from ≈1.1 to ≈0.82 W m^?1 K^?1 when 5.0% SrTe is added, correspondingly, the lattice thermal conductivity at 923 K decreases from ≈0.59 to ≈0.43 W m?¹ K^?1. The power factor maxima of PbTe_1?x Se_x ‐2Na‐4SrTe shift systematically to higher temperature with rising Se fractions due to bands divergence. The maximum power factors reach ≈27, ≈30, ≈31 μW cm^?1 K^?2 for the x = 0, 0.05, and 0.15 samples peak at 473, 573, and 623 K, respectively. The results indicate that ZT can be increased by synergistic integration of band structure engineering and all‐scale hierarchical architectures.     

Zwitterionic Sulfobetaine Hydrogel Electrolyte Building Separated Positive/Negative Ion Migration Channels for Aqueous Zn‐MnO2 Batteries with Superior Rate Capabilities

Hydrogel electrolytes have attracted increasing attention due to their potential uses in the fabrication of flexible solid‐state batteries. However, the development of hydrogel electrolytes is still in the initial stage and the number of available strategies is limited. Ideally, the hydrogel electrolyte should exhibit suitable ionic conductivity rate, mechanical strength, and biocompatibility for safety. In this study, a zwitterionic sulfobetaine/cellulose hydrogel electrolyte is fabricated using raw materials from natural plants, which exhibits a good biocompatibility with mammalian cells. The intrinsic zwitterionic groups on sulfobetaine chains can provide separated ion migration channels for positive and negative ions, which largely facilitates electrolyte ion transport. A solid‐state Zn‐MnO₂ battery with a fabricated zwitterionic gel electrolyte exhibits a very high rate performance. It exhibits a specific capacity of 275 mA h ${\text{g}}_{{\text{MnO}}_2}^{?1}$ at 1 C. Even up to 30 C, a high capacity of 74 mA h ${\text{g}}_{{\text{MnO}}_2}^{?1}$ is maintained during the charging–discharging for up to 10 000 cycles. For wearable applications, the flexible solid‐state batteries can be used as reliable and portable sources to power different wearable electronics such as a commercial smart watch, electroluminescent panel, and color electroluminescence line, which shows their large potentials for use in next‐generation flexible and wearable battery technologies.     

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Ni‐rich Li[Ni_xCo_yMn_1?x?y]O₂ (x ≥ 0.8) layered oxides are the most promising cathode materials for lithium‐ion batteries due to their high reversible capacity of over 200 mAh g^?1. Unfortunately, the anisotropic properties associated with the α‐NaFeO₂ structured crystal grains result in poor rate capability and insufficient cycle life. To address these issues, a micrometer‐sized Ni‐rich LiNi_0.8Co_0.1Mn_0.1O₂ secondary cathode material consisting of radially aligned single‐crystal primary particles is proposed and synthesized. Concomitant with this unique crystallographic texture, all the exposed surfaces are active {010} facets, and 3D Li⁺ ion diffusion channels penetrate straightforwardly from surface to center, remarkably improving the Li⁺ diffusion coefficient. Moreover, coordinated charge–discharge volume change upon cycling is achieved by the consistent crystal orientation, significantly alleviating the volume‐change‐induced intergrain stress. Accordingly, this material delivers superior reversible capacity (203.4 mAh g^?1 at 3.0–4.3 V) and rate capability (152.7 mAh g^?1 at a current density of 1000 mA g^?1). Further, this structure demonstrates excellent cycling stability without any degradation after 300 cycles. The anisotropic morphology modulation provides a simple, efficient, and scalable way to boost the performance and applicability of Ni‐rich layered oxide cathode materials.     

Free radical scavenging activity of novel thiazolidine‐2,4‐dione derivatives

Free radical activity towards superoxide anion radical (), hydroxyl radical (HO^?) and 2,2‐diphenyl‐1‐picrylhydrazyl (DPPH^?) of a series of novel thiazolidine‐2,4‐dione derivatives (TSs) was examined using chemiluminescence, electron paramagnetic resonance (EPR) and EPR spin trapping techniques. 5,5‐Dimethyl‐1‐pyrroline‐N‐oxide (DMPO) was applied as the spin trap. Superoxide radical was produced in the potassium superoxide/18‐crown‐6 ether dissolved in dimethyl sulfoxide. Hydroxyl radical was generated in the Fenton reaction (Fe(II) + H₂O₂. It was found that TSs showed a slight scavenging effect (15–38% reduction at 2.5 mmol/L concentration) of the DPPH radical and a high scavenging effect of (41–88%). The tested compounds showed inhibition of HO^? ‐dependent DMPO‐OH spin adduct formation (the amplitude of EPR signal decrease ranged from 20 to 76% at 2.5 mmol/L concentration. Our findings present new group compounds of relatively high reactivity towards free radicals. Copyright © 2012 John Wiley & Sons, Ltd.     

Metallic Photonic Crystal Absorber‐Emitter for Efficient Spectral Control in High‐Temperature Solar Thermophotovoltaics

A high‐temperature stable solar absorber based on a metallic 2D photonic crystal (PhC) with high and tunable spectral selectivity is demonstrated and optimized for a range of operating temperatures and irradiances. In particular, a PhC absorber with solar absorptance 0.86 and thermal emittance = 0.26 at 1000 K, using high‐temperature material properties, is achieved resulting in a thermal transfer efficiency more than 50% higher than that of a blackbody absorber. Furthermore, an integrated double‐sided 2D PhC absorber/emitter pair is demonstrated for a high‐performance solar thermophotovoltaic (STPV) system. The 2D PhC absorber/emitter is fabricated on a double‐side polished tantalum substrate, characterized, and tested in an experimental STPV setup along with a flat Ta absorber and a nearly blackbody absorber composed of an array of multiwalled carbon nanotubes (MWNTs). At an irradiance of 130 kW m^?2 the PhC absorber enables more than a two‐fold improvement in measured STPV system efficiency (3.74%) relative to the nearly blackbody absorber (1.60%) and higher efficiencies are expected with increasing operating temperature. These experimental results show unprecedented high efficiency, demonstrating the importance of the high selectivity of the 2D PhC absorber and emitter for high‐temperature energy conversion.     

In Situ Formation of Co9S8 Quantum Dots in MOF‐Derived Ternary Metal Layered Double Hydroxide Nanoarrays for High‐Performance Hybrid Supercapacitors

Layered double hydroxides (LDHs) are promising cathode materials for supercapacitors because of the enhanced flow efficiency of ions in the interlayers. However, the limited active sites and monotonous metal species further hinder the improvement of the capacity performance. Herein, cobalt sulfide quantum dots (Co₉S₈‐QDs) are effectively created and embedded within the interlayer of metal‐organic‐frameworks‐derived ternary metal LDH nanosheets based on in situ selective vulcanization of Co on carbon fibers. The hybrid CF@NiCoZn‐LDH/Co₉S₈‐QD retains the lamellar structure of the ternary metal LDH very well, inheriting low transfer impedance of interlayer ions. Significantly, the selectively generated Co₉S₈‐QDs expose more abundant active sites, effectively improving the electrochemical properties, such as capacitive performance, electronic conductivity, and cycling stability. Due to the synergistic relationship, the hybrid material delivers an ultrahigh electrochemical capacity of 350.6 mAh g^?1 (2504 F g^?1) at 1 A g^?1. Furthermore, hybrid supercapacitors fabricated with CF@NiCoZn‐LDH/Co₉S₈‐QD and carbon nanosheets modified by single‐walled carbon nanotubes display an outstanding energy density of 56.4 Wh kg^?1 at a power density of 875 W kg^?1, with an excellent capacity retention of 95.3% after 8000 charge–discharge cycles. Therefore, constructing hybrid electrode materials by in situ‐created QDs in multimetallic LDHs is promising.     

New Class of Ni‐Rich Cathode Materials Li[NixCoyB1−x−y]O2 for Next Lithium Batteries

A new class of layered cathodes, Li[Ni_xCo_yB_1?x?y]O₂ (NCB), is synthesized. The proposed NCB cathodes have a unique microstructure in which elongated primary particles are tightly packed into spherical secondary particles. The cathodes also exhibit a strong crystallographic texture in which the a–b layer planes are aligned along the radial direction, facilitating Li migration. The microstructure, which effectively suppresses the formation of microcracks, improves the cycling stability of the NCB cathodes. The NCB cathode with 1.5 mol% B delivers a discharge capacity of 234 mAh g^?1 at 0.1 C and retains 91.2% of its initial capacity after 100 cycles (compared to values of 229 mAh g^?1 at 0.1 C and 78.8% for pristine Li[Ni_0.9Co_0.1]O₂). This study shows the importance of controlling the microstructure to obtain the required cycling stability, especially for Ni‐rich layered cathodes, where the main cause of capacity fading is related to mechanical strain in their charged state.     

Controlled Atomic Solubility in Mn‐Rich Composite Material to Achieve Superior Electrochemical Performance for Li‐Ion Batteries

The quest for high energy density and high power density electrode materials for lithium‐ion batteries has been intensified to meet strongly growing demand for powering electric vehicles. Conventional layered oxides such as Co‐rich LiCoO₂ and Ni‐rich Li(Ni_xMn_yCo_z)O₂ that rely on only transition metal redox reaction have been faced with growing constraints due to soaring price on cobalt. Therefore, Mn‐rich electrode materials excluding cobalt would be desirable with respect to available resources and low cost. Here, the strategy of achieving both high energy density and high power density in Mn‐rich electrode materials by controlling the solubility of atoms between phases in a composite is reported. The resulting Mn‐rich material that is composed of defective spinel phase and partially cation‐disordered layered phase can achieve the highest energy density, ≈1100 W h kg^?1 with superior power capability up to 10C rate (3 A g^?1) among other reported Mn‐rich materials. This approach provides new opportunities to design Mn‐rich electrode materials that can achieve high energy density and high power density for Li‐ion batteries.     

NMR‐based conformation and dynamics of a tetrasaccharide‐repeating sulfated fucan substituted by different counterions

The sulfated fucan from the sea urchin Lytechinus variegatus is composed of the repetitive sequence [‐3)‐α‐l ‐Fucp‐4( )‐(1‐3)‐α‐l ‐Fucp‐2,4‐di( )‐(1‐3)‐α‐l ‐Fucp‐2( )‐(1‐3)‐α‐l ‐Fucp‐2( )‐(1‐]_n. Conformation (of rings and chains) and dynamics of this tetrasaccharide‐repeating sulfated fucan substituted by Na⁺, Ca²⁺, and Li⁺ as counterions have been examined through experiments of liquid‐state nuclear magnetic resonance spectroscopy. Scalar coupling and nuclear Overhauser effect (NOE)‐based data have confirmed that all composing units occur as ¹C₄ chair conformer regardless of the cation type, unit position within the repeating sequence, and sulfation type. Chain conformation determined by NOE signal pattern assisted by molecular modeling for a theoretical octasaccharide has shown a similar linear 3D structure for the three differently substituted forms. Data derived from spin‐relaxation measurements have indicated a contribution of counterion type to dynamics. The calcium‐based preparation has shown the highest mobility while the sodiated one showed the lowest mobility. The set of results from this work suggests that counterion type can affect the physicochemical properties of the structurally well‐defined sulfated fucan. The counterion effect seems to impact more on the structural mobility than on average conformation of the studied sulfated glycan in solution.     

Improved Cycling Stability of Li[Ni0.90Co0.05Mn0.05]O2 Through Microstructure Modification by Boron Doping for Li‐Ion Batteries

Boron‐doped Li[Ni_0.90Co_0.05Mn_0.05]O₂ cathodes are synthesized by adding B₂O₃ during the lithiation of the hydroxide precursor. Density functional theory confirms that boron doping at a level as low as 1 mol% alters the surface energies to produce a highly textured microstructure that can partially relieve the intrinsic internal strain generated during the deep charging of Li[Ni_0.90Co_0.05Mn_0.05]O₂. The 1 mol% B‐Li[Ni_0.90Co_0.05Mn_0.05]O₂ cathode thus delivers a discharge capacity of 237 mAh g^?1 at 4.3 V, with an outstanding capacity retention of 91% after 100 cycles at 55 °C, which is 15% higher than that of the undoped Li[Ni_0.90Co_0.05Mn_0.05]O₂ cathode. This proposed synthesis strategy demonstrates that an optimal microstructure exists for extending the cycle life of Ni‐rich Li[Ni_1‐x‐yCo_xMn_y]O₂ cathodes that have an inadequate cycling stability in electric vehicle applications and indicates that an optimal microstructure can be achieved through surface energy modification.     

Grafting Benzenediazonium Tetrafluoroborate onto LiNixCoyMnzO2 Materials Achieves Subzero‐Temperature High‐Capacity Lithium‐Ion Storage via a Diazonium Soft‐Chemistry Method

Subzero‐temperature Li‐ion batteries (LIBs) are highly important for specific energy storage applications. Although the nickel‐rich layered lithium transition metal oxides(LiNi_xCo_yMn_zO₂) (LNCM) (x > 0.5, x + y +z = 1) are promising cathode materials for LIBs, their very slow Li‐ion diffusion is a main hurdle on the way to achieve high‐performance subzero‐temperature LIBs. Here, a class of low‐temperature organic/inorganic hybrid cathode materials for LIBs, prepared by grafting a conducting polymer coating on the surface of 3 µm sized LiNi_0.6Co_0.2Mn_0.2O₂ (LNCM‐3) material particles via a greener diazonium soft‐chemistry method is reported. Specifically, LNCM‐3 particles are uniformly coated with a thin polyphenylene film via the spontaneous reaction between LNCM‐3 and C₆H₅N₂⁺BF₄^?. Compared with the uncoated one, the polyphenylene‐coated LNCM‐3 (polyphenylene/LNCM‐3) has shown much improved low‐temperature discharge capacity (≈148 mAh g^?1 at 0.1 C, ?20 °C), outstanding rate capability (≈105 mAh g^?1 at 1 C, ?20 °C), and superior low‐temperature long‐term cycling stability (capacity retention is up to 90% at 0.5 C over 1150 cycles). The low‐temperature performance of polyphenylene/LNCM‐3 is the best among the reported state‐of‐the art cathode materials for LIBs. The present strategy opens up a new avenue to construct advanced cathode materials for wider range applications.