Fed-batch Cultivation of Mucor indicus in Dilute-acid Lignocellulosic Hydrolyzate for Ethanol Production

Mucor indicus fermented dilute-acid lignocellulosic hydrolyzates to ethanol in fed-batch cultivation with complete hexose utilization and partial uptake of xylose. The fungus was tolerant to the inhibitors present in the hydrolyzates. It grew in media containing furfural (1 g/l), hydroxymethylfurfural (1 g/l), vanillin (1 g/l), or acetic acid (7 g/l), but did not germinate directly in the hydrolyzate. However, with fed-batch methodology, after initial growth of M. indicus in 500 ml enzymatic wheat hydrolyzate, lignocellulosic hydrolyzate was fermented with feeding rates 55 and 100 ml/h. The fungus consumed more than 46% of the initial xylose, while less than half of this xylose was excreted in the form of xylitol. The ethanol yield was 0.43 g/g total consumed sugar, and reached the maximum concentration of 19.6 g ethanol/l at the end of feeding phase. Filamentous growth, which is regarded as the main obstacle to large-scale cultivation of M. indicus, was avoided in the fed-batch experiments.     

Osmotic pressure effects and intracellular accumulation of ethanol in yeast during fermentation

Summary The intracellular accumulation of ethanol in yeast and its potential effects on growth and fermentation have been topics of controversy for the past several years. The determination of intracellular ethanol based on the exclusion of [¹⁴C]sorbitol to estimate aqueous cell volume was used to examine the question of intracellular ethanol accumulation. An intracellular accumulation of ethanol inSaccharomyces cerevisiae was observed during the early stages of fermentation. However, as fermentation continued, the intracellular and extracellular concentrations of ethanol became similar. Increasing the osmotic pressure of the medium with glucose or sorbitol was observed to cause an increase in the intracellular ethanol concentration. Associated with this was a decrease in yeast growth and fermentation rates. In addition, increasing the osmotic pressure of the medium was observed to cause an increase in glycerol production. Supplementation of the media with excess peptone, yeast extract, magnesium sulfate and potassium phosphate was found to relieve the detrimental effects of high osmotic pressure. Under these conditions, though, no effect on the intracellular and extracellular ethanol distribution was observed. These results indicate that nutrient limitation, and not necessarily intracellular ethanol accumulation, plays a key role during yeast fermentations in media of high osmolarity.     

Alcoholic fermentation of xylose and mixed sugars using recombinant <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis> engineered for xylose utilization

Previously, a Saccharomyces cerevisiae strain was engineered for xylose assimilation by the constitutive overexpression of the Orpinomyces xylose isomerase, the S. cerevisiae xylulokinase, and the Pichia stipitis SUT1 sugar transporter genes. The recombinant strain exhibited growth on xylose, under aerobic conditions, with a specific growth rate of 0.025 h⁻¹, while ethanol production from xylose was achieved anaerobically. In the present study, the developed recombinant yeast was adapted for enhanced growth on xylose by serial transfer in xylose-containing minimal medium under aerobic conditions. After repeated batch cultivations, a strain was isolated which grew with a specific growth rate of 0.133 h⁻¹. The adapted strain could ferment 20 g l⁻¹ of xylose to ethanol with a yield of 0.37 g g⁻¹ and production rate of 0.026 g l⁻¹ h⁻¹. Raising the fermentation temperature from 30°C to 35°C resulted in a substantial increase in the ethanol yield (0.43 g g⁻¹) and production rate (0.07 g l⁻¹ h⁻¹) as well as a significant reduction in the xylitol yield. By the addition of a sugar complexing agent, such as sodium tetraborate, significant improvement in ethanol production and reduction in xylitol accumulation was achieved. Furthermore, ethanol production from xylose and a mixture of glucose and xylose was also demonstrated in complex medium containing yeast extract, peptone, and borate with a considerably high yield of 0.48 g g⁻¹.     

Fermentation of sugar cane bagasse hemicellulosic hydrolysate and sugar mixtures to ethanol by recombinant Escherichia coli KO11

Escherichia coli KO11, carrying the ethanol pathway genes pdc (pyruvate decarboxylase) and adh (alcohol dehydrogenase) from Zymomonas mobilis integrated into its chromosome, has the ability to metabolize pentoses and hexoses to ethanol, both in synthetic medium and in hemicellulosic hydrolysates. In the fermentation of sugar mixtures simulating hemicellulose hydrolysate sugar composition (10.0 g of glucose/l and 40.0 g of xylose/l) and supplemented with tryptone and yeast extract, recombinant bacteria produced 24.58 g of ethanol/l, equivalent to 96.4% of the maximum theoretical yield. Corn steep powder (CSP), a byproduct of the corn starch-processing industry, was used to replace tryptone and yeast extract. At a concentration of 12.5 g/l, it was able to support the fermentation of glucose (80.0 g/l) to ethanol, with both ethanol yield and volumetric productivity comparable to those obtained with fermentation media containing tryptone and yeast extract. Hemicellulose hydrolysate of sugar cane bagasse supplemented with tryptone and yeast extract was also readily fermented to ethanol within 48 h, and ethanol yield achieved 91.5% of the theoretical maximum conversion efficiency. However, fermentation of bagasse hydrolysate supplemented with 12.5 g of CSP/l took twice as long to complete. This revised version was published online in November 2006 with corrections to the Cover Date.     

Cassava as a Cheap Source of Carbon for Rhizobial Inoculant Production using an Amylase-producing Fungus and a Glycerol-producing Yeast

Summary The aim of this research was to develop methods to use low-cost carbon compounds for rhizobial inoculant production. Five raw starch materials; steamed cassava, sticky rice, fresh corn, dry corn and sorghum were tested for sugar production by an amylase-producing fungus. Streamed cassava produced the highest amount of reducing sugar after fermentation. Bradyrhizobium japonicum USDA110, Azorhizobium caulinodans IRBG23, Rhizobium phaseoli TAL1383, Sinorhizobium fredii HH103, and Mesorhizobium ciceri USDA2429 were tested on minimal medium supplemented with reducing sugar obtained from cassava fermentation. All strains, except B. japonicum USDA110, could grow in medium containing cassava sugar derived from 100 g steamed cassava per litre, and the growth rates for these strains were similar to those in medium containing 0.5 (w/v) mannitol. The sugar derived from steamed cassava was further used for production of glycerol using yeast. After 1 day of yeast fermentation, the culture containing glycerol and heat-killed yeast cells, was used to formulate media for culturing bradyrhizobia. A formulation medium, FM4, with a glycerol concentration of 0.6 g/l and yeast cells (OD₆₀₀ = 0.1) supported growth of B. japonicum USDA110 up to 3.61 × 10⁹ c.f.u./ml in 7 days. These results demonstrate that steamed cassava could be used to provide cheap and effective carbon sources for rhizobial inoculant production.     

Multiple growth inhibition of <Emphasis Type="Italic">Klebsiella pneumoniae</Emphasis> in 1,3-propanediol fermentation

The inhibition of substrate and product on the growth of Klebsiella pneumoniae in anaerobic and aerobic batch fermentation for the production of 1,3-propanediol was studied. The cells under anaerobic conditions had a higher maximum specific growth rate of 0.19 h^–1 and lower tolerance to 110 g glycerol l^–1, compared to the maximum specific growth rate of 0.17 h^–1 and tolerance to 133 g glycerol l^–1 under aerobic conditions. Acetate was the main inhibitory metabolite during the fermentation under anaerobic conditions, with lactate and ethanol the next most inhibitory. The critical concentrations of acetate, lactate and ethanol were assessed to be 15, 19, 26 g l^–1, respectively. However, cells grown under aerobic conditions were more resistant to acetate and lactate but less resistant to ethanol. The critical concentrations of acetate, lactate and ethanol were assessed to be 24, 26, and 17 g l^–1, respectivelyRevisions requested 8 september; Revisions received 2 November 2004     

Ethanol production from hexoses, pentoses, and dilute-acid hydrolyzate by Mucor indicus

Consumption of hexoses and pentoses and production of ethanol by Mucor indicus were investigated in both synthetic media and dilute-acid hydrolyzates. The fungus was able to grow in a poor medium containing only carbon, nitrogen, phosphate, potassium, and magnesium sources. However, the cultivation took more than a week and the ethanol yield was only 0.2 gg(-1). Enrichment of the medium by addition of trace metals, particularly zinc and yeast extract, improved the growth rate and yield, such that the cultivation was completed in less than 24 h and the ethanol and biomass yields were increased to 0.40 and 0.20 gg(-1), respectively. The fungus was able to assimilate glucose, galactose, mannose, and xylose, and produced ethanol with yields of 0.40, 0.34, 0.39, and 0.18 gg(-1), respectively. However, arabinose was poorly consumed and no formation of ethanol was detected. Glycerol was the major by-product in the cultivation on the hexoses, while formation of glycerol and xylitol were detected in the cultivation of the fungus on xylose. The fungus was able to take up the sugars present in dilute-acid hydrolyzate as well as the inhibitors, acetic acid, furfural, and hydroxymethyl furfural. M. indicus was able to grow under anaerobic conditions when glucose was the sole carbon source, but not on xylose or the hydrolyzate. The yield of ethanol in anaerobic cultivation on glucose was 0.46 g g(-1).     

Aeration alleviates ethanol inhibition and glycerol production during fed-batch ethanol fermentation

In this study, we investigated the effects of aeration on ethanol inhibition and glycerol production during fed-batch ethanol fermentation. When aeration was conducted at 0.13, 0.33, and 0.8 vvm, the ethanol productivity, specific ethanol production rate, and ethanol yield in the presence of greater than 100 g/L of ethanol were higher than when aeration was not conducted. In addition, estimation of the parameters (α and β) in a model equation of ethanol inhibition kinetics indicated that aeration alleviated ethanol inhibition against the specific growth rate and the specific ethanol production rate. Specifically, when aeration was conducted, the glycerol yield and specific glycerol production rate decreased approximately 50 and 70%, respectively. Finally, the results of this study indicated that aeration during fed-batch ethanol fermentation may improve the ethanol concentration in the final culture broth, as well as the ethanol productivity.     

Production of 1,3-propanediol by <Emphasis Type="Italic">Clostridium butyricum</Emphasis> VPI 3266 using a synthetic medium and raw glycerol

Growth inhibition of Clostridium butyricum VPI 3266 by raw glycerol, obtained from the biodiesel production process, was evaluated. C. butyricum presents the same tolerance to raw and to commercial glycerol, when both are of similar grade, i.e. above 87% (w/v). A 39% increase of growth inhibition was observed in the presence of 100 g l^–1 of a lower grade raw glycerol (65% w/v). Furthermore, 1,3-propanediol production from two raw glycerol types (65% w/v and 92% w/v), without any prior purification, was observed in batch and continuous cultures, on a synthetic medium. No significant differences were found in C. butyricum fermentation patterns on raw and commercial glycerol as the sole carbon source. In every case, 1,3-propanediol yield was around 0.60 mol/mol glycerol consumed.     

Determination of Growth and Glycerol Production Kinetics of a Wine Yeast Strain Saccharomyces cerevisiae Kalecik 1 in Different Substrate Media

Summary Glycerol has been known as an important by-product of wine fermentations improving the sensory quality of wine. This study was carried out with an endogenic wine yeast strain Saccharomyces cerevisiae Kalecik 1. The kinetics of growth and glycerol biosynthesis were analysed at various initial concentrations of glucose, fructose, and sucrose in a batch system. Depending on the determined values of Monod constants, glucose (K_s = 28.09 g/l) was found as the most suitable substrate for the yeast growth. Initial glucose, fructose and sucrose concentrations necessary for maximum specific yeast growth rate were determined as 175 g, 100 l, and 200 g/l, respectively. The yeast produced glycerol at very high concentrations in fructose medium. Fructose was determined as the most suitable substrate for glycerol production while the strain showed low tendency to use it for growth. S. cerevisiae Kalecik 1 could not produce glycerol below 200 g/l initial sucrose concentration. When natural white grape juice was used as fermentation medium, maximum glycerol concentration and dry weight of the yeast were determined as 9.3 g/l and 11.8 g/l, respectively.     

Ethanol production from xylose by Thermoanaerobacter ethanolicus in batch and continuous culture

The fermentation of xylose by Thermoanaerobacter ethanolicus ATCC 31938 was studied in pH-controlled batch and continuous cultures. In batch culture, a dependency of growth rate, product yield, and product distribution upon xylose concentration was observed. With 27 mM xylose media, an ethanol yield of 1.3 mol ethanol/mol xylose (78% of maximum theoretical yield) was typically obtained. With the same media, xylose-limited growth in continuous culture could be achieved with a volumetric productivity of 0.50 g ethanol/liter h and a yield of 0.42 g ethanol/g xylose (1.37 mol ethanol/mol xylose). With extended operation of the chemostat, variation in xylose uptake and a decline in ethanol yield was seen. Instability with respect to fermentation performance was attributed to a selection for mutant populations with different metabolic characteristics. Ethanol production in these T. ethanolicus systems was compared with xylose-to-ethanol conversions of other organisms. Relative to the other systems, T. ethanolicus offers the advantages of a high ethanol yield at low xylose concentrations in batch culture and of a rapid growth rate. Its disadvantages include a lower ethanol yield at higher xylose concentrations in batch culture and an instability of fermentation characteristics in continuous culture.     

Impact of balanced substrate flux on the metabolic process employing fuzzy logic during the cultivation of <Emphasis Type="Italic">Bacillus thuringiensis</Emphasis> var.<Emphasis Type="Italic"> Galleriae</Emphasis>

Summary The insecticidal crystal protein (ICP) synthesized at the onset of sporulation by Bacillus thuringiensis var. galleriae (Btg) is lethal against specific pests. Attempts were made to enhance the synthesis of biomass and ICP by Btg employing process optimization strategies. The process optimization was carried out with residual glucose concentration control in a bench scale bioreactor. A fuzzy logic-based feedback control system for maintaining the residual glucose concentration at a constant level during cultivation was developed in LabVIEW. This control system indicated the possibilities in providing a balanced substrate flux during cultivation. The identified optimum level of 2.72 g/l in residual glucose concentration was maintained by fed-batch cultivation with glucose and yeast extract fed at equal concentration with the above control system. High cell density of 16.0 g/l with specific growth rate of 0.69 h^-1 was obtained during the cultivation. The balanced flux of substrate during cultivation has resulted in the enhanced synthesis of biomass and ICP. This optimized process could be commercially exploited by comparing the fluxes of basal compounds in different media sources used in fermentation.     

Fermentation of <Emphasis Type="SmallCaps">d</Emphasis>-glucose and <Emphasis Type="SmallCaps">d</Emphasis>-xylose mixtures by <Emphasis Type="Italic">Candida tropicalis</Emphasis> NBRC 0618 for xylitol production

The fermentation of d-glucose and d-xylose mixtures by the yeast Candida tropicalis NBRC 0618 has been studied under the most favourable operation conditions for the culture, determining the most adequate initial proportion in these sugars for xylitol production. In all the experiments a synthetic culture medium was used, with an initial total substrate concentration of 25 g L⁻¹, a constant pH of 5.0 and a temperature of 30 °C. From the experimental results, it was deduced that the highest values of specific rates of production and of overall yield in xylitol were achieved for the mixtures with the highest percentage of d-xylose, specifically in the culture with the initial d-glucose and d-xylose concentrations of 1 and 24 g L⁻¹, respectively, with an overall xylitol yield of 0.28 g g⁻¹. In addition, the specific rates of xylitol production declined over the time course of the culture and the formation of this bioproduct was favoured by the presence of small quantities of d-glucose. The sum of the overall yield values in xylitol and ethanol for all the experiments ranged from 0.26 to 0.56 g bioproduct/g total substrate.     

Kinetic modeling of Candida shehatae ATCC 22984 on xylose and glucose for ethanol production

Candida shehatae ATCC 22984, a xylose-fermenting yeast, showed an ability to produce ethanol in both glucose and xylose medium. Maximum ethanol produced by the yeast was 48.8?g/L in xylose and 52.6?g/L in glucose medium with ethanol yields that varied between 0.3 and 0.4?g/g depended on initial sugar concentrations. Xylitol was a coproduct of ethanol production using xylose as substrate, and glycerol was detected in both glucose and xylose media. Kinetic model equations indicated that growth, substrate consumption, and product formation of C. shehatae were governed by substrate limitation and inhibition by ethanol. The model suggested that cell growth was totally inhibited at 40?g/L of ethanol and ethanol production capacity of the yeast was 52?g/L, which were in good agreement with experimental results. The developed model could be used to explain C. shehatae fermentation in glucose and xylose media from 20 to 170?g/L sugar concentrations.     

Production of Fructose and Ethanol from Cane Molasses Using Saccharomyces cerevisiae ATCC 36858

The purpose of this research was to study the possibility of the production of ethanol and enriched fructose syrups from sugar cane molasses using the yeast Saccharomyces cerevisiae ATCC 36858. In batch experiments with a total sugar concentration of between 96.7 g/l and 323.5 g/l, the fructose yield was above 90% of the theoretical value. The ethanol yield and volumetric productivity were in the range of 66% and 77% of the theoretical value, and between 0.53 g ethanol/l × h and 3.15 g ethanol/l × h, respectively. The fructose fraction in the carbohydrates content of the produced syrups was more than 95% when the total initial sugar concentration in the medium was below 273.8 g/l. Some oligosaccharides and glycerol were also produced in all tested media. The maximum amount of produced oligosaccharides including raffinose accounted for 13.4 g/l in the cane molasses medium with 323.5 g/l sugars in the initial phase of the fermentation process. The oligosaccharides produced and raffinose were completely consumed by the end of the fermentation process when the total initial sugar concentration was less than 191.3 g/l. The glycerol concentration was below 9.9 g/l. These findings are useful in the production of ethanol and high fructose syrups using sugar cane molasses.     

补料分批发酵过程中两阶段发酵生产1,3-丙二醇

在补料分批发酵过程中提高比生长速率不仅减少乙醇、甲酸的生成,而且提高1,3-丙二醇的得率和比生产速率.发酵后期甘油的浓度在15～26 g/L时有利于提高1,3-丙二醇的生产.采取在发酵前期控制菌体较高比生长速率和发酵后期控制适宜甘油浓度相结合的策略,有效地提高了1,3-丙二醇的生产,降低副产物乳酸和乙醇的生成.     

Sugar fermentation by <Emphasis Type="Italic">Fusarium oxysporum</Emphasis> to produce ethanol

As a first step in the research on ethanol production from lignocellulose residues, sugar fermentation by Fusarium oxysporum in oxygen-limited conditions is studied in this work. As a substrate, solutions of arabinose, glucose, xylose and glucose/xylose mixtures are employed. The main kinetic and yield parameters of the process are determined according to a time-dependent model. The microorganism growth is characterized by the maximum specific growth rate and biomass productivity, the substrate consumption is studied through the specific consumption rate and biomass yield, and the product formation via the specific production rate and product yields. In conclusion, F. oxysporum can convert glucose and xylose into ethanol with product yields of 0.38 and 0.25, respectively; when using a glucose/xylose mixture as carbon source, the sugars are utilized sequentially and a maximum value of 0.28 g/g ethanol yield is determined from a 50% glucose/50% xylose mixture. Although fermentation performance by F.␣oxysporum is somewhat lower than that of other fermenting microorganisms, its ability for simultaneous lignocellulose-residue saccharification and fermentation is considered as a potential advantage.     

In situ detoxification and continuous cultivation of dilute-acid hydrolyzate to ethanol by encapsulated S. cerevisiae

Dilute-acid lignocellulosic hydrolyzate was successfully fermented to ethanol by encapsulated Saccharomyces cerevisiae at dilution rates up to 0.5h(-1). The hydrolyzate was so toxic that freely suspended yeast cells could ferment it continuously just up to dilution rate 0.1h(-1), where the cells lost 75% of their viability measured by colony forming unit (CFU). However, encapsulation increased their capacity for in situ detoxification of the hydrolyzate and protected the cells against the inhibitors present in the hydrolyzate. While the cells were encapsulated, they could successfully ferment the hydrolyzate at tested dilution rates 0.1-0.5h(-1), and keep more than 75% cell viability in the worst conditions. They produced ethanol with yield 0.44+/-0.01 g/g and specific productivity 0.14-0.17 g/(gh) at all dilution rates. Glycerol was the main by-product of the cultivations, which yielded 0.039-0.052 g/g. HMF present in the hydrolyzate was converted 48-71% by the encapsulated yeast, while furfural was totally converted at dilution rates 0.1 and 0.2h(-1) and partly at the higher rates. Continuous cultivation of encapsulated yeast was also investigated on glucose in synthetic medium up to dilution rate 1.0 h(-1). At this highest rate, ethanol and glycerol were also the major products with yields 0.43 and 0.076 g/g, respectively. The experiments lasted for 18-21 days, and no damage in the capsules was detected.     

The role of nisin in fuel ethanol production with Saccharomyces cerevisiae

Aims: To investigate the effects of nisin on lactobacilli contamination of yeast during ethanol fermentation and to determine the appropriate concentration required to control the growth of selected lactobacilli in a YP/glucose media fermentation model. Methods and Results: The lowest concentration of nisin tested (5 IU ml^?1) effectively controlled the contamination of YP/glucose media with 10⁶ CFU ml^?1 lactobacilli. Lactic acid yield decreased from 5·0 to 2·0 g l^?1 and potential ethanol yield losses owing to the growth and metabolism of Lactobacillus plantarum and Lactobacillus brevis were reduced by 11 and 7·8%, respectively. Approximately, equal concentrations of lactic acid were produced by Lact. plantarum and Lact. brevis in the presence of 5 and 2 IU ml^?1 nisin, respectively, thus demonstrating the relatively higher nisin sensitivity of Lact. brevis for the strains in this study. No differences were observed in the final ethanol concentrations produced by yeast in the absence of bacteria at any of the nisin concentrations tested. Conclusions: Metabolism of contaminating bacteria was reduced in the presence of 5 IU ml^?1 nisin, resulting in reduced lactic acid production and increased ethanol production by the yeast. Significance and Impact of the Study: Bacteriocins represent an alternative to the use of antibiotics for the control of bacterial contamination in fuel ethanol plants and may be important in preventing the emergence of antibiotic‐resistant contaminating strains.     

Growth and cyclosporin a production by an indigenously isolated strain ofTolypocladium inflatum

A fungal culture isolated from a local soil sample which showed antifungal activity and produced cyclosporin A, was identified asTolypocladium inflatum. The culture grew best in a medium containing 1% maltose (pH 5–6) when inoculated with a one-day-old inoculum at 2% (V/V) concentration. Under batch fermentation conditions, growth and cyclosporin A production were better in complex media (24.6 g biomass and 205 mg cyclosporin A per liter) in comparison with synthetic media (6.84 g biomass and 35 mg cyclosporin A per liter). While addition of peptone increased culture growth (high biomass yield), supplementation with casein acid hydrolyzate favored cyclosporin A production.