Zinc deprivation of methanol fed anaerobic granular sludge bioreactors

The effect of omitting zinc from the influent of mesophilic (30 degrees C) methanol fed upflow anaerobic sludge bed (UASB) reactors, and latter zinc supplementation to the influent to counteract the deprivation, was investigated by coupling the UASB reactor performance to the microbial ecology of the bioreactor sludge. Limitation of the specific methanogenic activity (SMA) on methanol due to the absence of zinc from the influent developed after 137 days of operation. At that day, the SMA in medium with a complete trace metal solution except Zn was 3.4 g CH4-COD g VSS(-1) day(-1), compared to 4.2 g CH4-COD g VSS(-1) day(-1) in a medium with a complete (including zinc) trace metal solution. The methanol removal capacity during these 137 days was 99% and no volatile fatty acids accumulated. Two UASB reactors, inoculated with the zinc-deprived sludge, were operated to study restoration of the zinc limitation by zinc supplementation to the bioreactor influent. In a first reactor, no changes to the operational conditions were made. This resulted in methanol accumulation in the reactor effluent after 12 days of operation, which subsequently induced acetogenic activity 5 days after the methanol accumulation started. Methanogenesis could not be recovered by the continuous addition of 0.5 microM ZnCl2 to the reactor for 13 days. In the second reactor, 0.5 microM ZnCl2 was added from its start-up. Although the reactor stayed 10 days longer methanogenically than the reactor operated without zinc, methanol accumulation was observed in this reactor (up to 1.1 g COD-MeOH L(-1)) as well. This study shows that zinc limitation can induce failure of methanol fed UASB reactors due to acidification, which cannot be restored by resuming the continuous supply of the deprived metal.     

Acidification of methanol-fed anaerobic granular sludge bioreactors by cobalt deprivation: Induction and microbial community dynamics

The acidification of mesophilic (30 degrees C) methanol-fed upflow anaerobic sludge bed (UASB) reactors induced by cobalt deprivation from the influent was investigated by coupling the reactor performance (pH 7.0; organic loading rate 4.5 g COD . L(-1) . d(-1)) to the microbial ecology of the bioreactor sludge. The latter was investigated by specific methanogenic activity (SMA) measurements and fluorescence in situ hybridization (FISH) to quantify the abundance of key organisms over time. This study hypothesized that under cobalt limiting conditions, the SMA on methanol of the sludge gradually decreases, which ultimately results in methanol accumulation in the reactor effluent. Once the methanol accumulation surpasses a threshold value (about 8.5 mM for the sludge investigated), reactor acidification occurs because acetogens outcompete methylothrophic methanogens at these elevated methanol concentrations. Methanogens present in granular sludge at the time of the acidification do not use methanol as the direct substrate and are unable to degrade acetate. Methylotrophic/acetoclastic methanogenic activity was found to be lost within 10 days of reactor operation, coinciding with the disappearance of the Methanosarcina population. The loss of SMA on methanol can thus be used as an accurate parameter to predict reactor acidification of methanol-fed UASB reactors operating under cobalt limiting conditions.     

Effect of nickel deprivation on methanol degradation in a methanogenic granular sludge bioreactor

The effect of omitting nickel from the influent on methanol conversion in an Upflow Anaerobic Sludge Bed (UASB) reactor was investigated. The UASB reactor (30°C, pH 7) was operated for 261 days at a 12-h hydraulic retention time (HRT) and at organic loading rates (OLRs) ranging from 2.6 to 7.8 g COD l reactor⁻¹ day⁻¹. The nickel content of the sludge decreased by 66% during the 261-day reactor run because of washout and doubling of the sludge bed volume. Nickel deprivation initially had a strong impact on the methanogenic activity of the sludge with methanol; e.g., after 89 days of operation, this activity was doubled by adding 2 μM nickel. Upon prolonged UASB reactor operation, methanol and VFA effluent concentrations decreased whereas the sludge lost its response to nickel addition in activity tests. This suggests that a less nickel-dependent methanol-converting sludge had developed in the UASB reactor. Received 09 April 2002/ Accepted in revised form 13 July 2002     

Effect of long-term cobalt deprivation on methanol degradation in a methanogenic granular sludge bioreactor

The effect of the trace metal cobalt on the conversion of methanol in an upflow anaerobic sludge bed (UASB) reactor was investigated by studying the effect of cobalt deprivation from the influent on the reactor efficiency and the sludge characteristics. A UASB reactor (30 degrees C; pH 7) was operated for 261 days at a 12-h hydraulic retention time (HRT). The loading rate was increased stepwise from 2.6 g chemical oxygen demand (COD) x L reactor(-1) x d(-1) to 7.8 g COD x L reactor(-1) x d(-1). Cobalt deprivation had a strong impact on the methanogenic activity of the sludge. In batch tests, the methanogenic activity of the sludge with methanol as the substrate increased 5.3 (day 28) and 2.1 (day 257) times by addition of 840 nM of cobalt. The sludge had an apparent K(m) for cobalt of 948 nM after 28 days of operation and 442 nM at the end of the run. Cobalt deprivation during 54 days of operation led to a methanol conversion efficiency of only 55%. Continuous addition of cobalt (330 nM) for 33 days improved the methanol removal efficiency to 100%. In this period of cobalt dosing, the cobalt concentration in the sludge increased 2.7 times up to 32 microg x g TSS(-1). Upon omission of the cobalt addition, cobalt washed-out at a stable rate of 0.1 microg x g VSS(-1) x d(-1). At the end of the run, the cobalt concentration of the sludge was similar to that of the seed sludge.     

Flocculants effect in biomass retention in a UASB reactor treating dairy manure

The performance and biomass retention of an upflow anaerobic sludge bed (UASB) reactor treating liquid fraction of dairy manure has been investigated at several organic loading rates. Two identical UASB reactors were employed. The biomass of one UASB reactor (FBR) had previously been treated with a cationic polyacrylamide, the other reactor was operated as a control reactor (CR). At 3 and 2 days of HRT both reactors functioned similarly, but at 1.5 days HRT some differences were observed between both effluents. Mean COD(T) removal percentages were 83.4% and 76.5%; COD(VFA) values in effluents were 977 and 2682 mg l(-1) for the FBR and the CR respectively. The VSS initial value in both reactors was 25.66 g VSS, whereas after the experiment the quantities were 31.83 g VSS in the FBR and 23.18 g VSS in the CR reactors. Polymer addition resulted in a higher degree of biomass retention and better performance in the FBR reactor.     

Stimulation of methanol degradation in UASB reactors: in situ versus pre-loading cobalt on anaerobic granular sludge

The effect of pre-loading and in situ loading of cobalt onto a cobalt-limited granular sludge on the performance of methanol fed bioreactors was investigated. One upflow anaerobic sludge bed (UASB) reactor was inoculated with cobalt pre-loaded sludge (24h; 30 degrees C; 1 mM CoCl2) and a second UASB with unloaded sludge. The UASB reactors (30 degrees C; pH 7) were operated for 77 days at 8 h hydraulic retention time and organic loading rates ranging from 5 to 20 g COD.L reactor(-1).d(-1). Cobalt pre-loading clearly stimulated the methanogenic activity of the sludge with methanol as the substrate, e.g., after 30 days of reactor operation this activity was 5.8 times higher than that of the cobalt unloaded sludge. During the experiment, part of the cobalt leached from the pre-loaded sludge, i.e., 54% of the cobalt content was lost during the 77 days of reactor operation. Sequential metal extraction showed that losses mainly occurred from the exchangeable and carbonate fraction and in the sludge remaining cobalt was mainly present in the organic/sulfide fraction of the sludge. In situ loading of cobalt in the unloaded UASB reactor on day 57 by adding 31 microM cobalt to the influent for a 24-h period (16% of the cobalt present in the loaded sludge at day 11) resulted in a 4 time increase of the methanogenic activity of the sludge with methanol as the substrate at the end of the reactor experiment, while the accumulated amount of cobalt in the sludge only amounted to 6% of the cobalt accumulated in the loaded sludge (on day 11). This study showed that both pre-loading sludge and in situ loading are adequate for achieving an increased reactor performance of methanol fed UASB reactors operating under cobalt limitation. However, the in situ dosing procedure needs substantially lower amounts of cobalt, while it also gives significantly smaller losses of cobalt with the effluent.     

Effect of sulfur source on the performance and metal retention of methanol-fed UASB reactors

The effect of a sulfur source on the performance and metal retention of methanol-fed upflow anaerobic sludge bed (UASB) reactors was investigated. For this purpose, two UASB reactors were operated with cobalt preloaded granular sludge (1 mM CoCl2; 30 degrees C; 24 h) at an organic loading rate (OLR) of 5 g COD.L reactor(-1).d(-1). One UASB reactor (R1) was operated without a sulfur source in the influent during the first 37 days. In this period the methanol conversion to methane remained very poor, apparently due to the absence of a sulfur source, because once cysteine, a sulfur-containing amino acid, was added to the influent of R1 (day 37) a full conversion of methanol to methane occurred within 6 days. The second reactor (R2) was operated with sulfate (0.41 mM) in the influent during the first 86 days of operation, during which no limitation in the methanol conversion to methane manifested. Cobalt washed out from the sludge at similar rates in both reactors. The leaching of cobalt occurred at two distinct rates, first at a high rate of 22 microg.g TSS(-1).d(-1), which proceeded mainly from the exchangeable and carbonate fraction and later at a relatively slow rate of 9 mug.g TSS(-1).d(-1) from the organic/sulfide fraction. This study showed that the supply of the sulfur source L-cysteine has a pronounced positive effect on the methanogenic activity and the retention of metals such as iron, zinc and molybdenum.     

Influence of pH shocks on trace metal dynamics and performance of methanol fed granular sludge bioreactors

The influence of pH shocks on the trace metal dynamics and performance of methanol fed upflow anaerobic granular sludge bed (UASB) reactors was investigated. For this purpose, two UASB reactors were operated with metal pre-loaded granular sludge (1mM Co, Ni and Fe; 30°C; 96h) at an organic loading rate (OLR) of 5gCOD l reactor^–1d^–1. One UASB reactor (R1) was inoculated with sludge that originated from a full scale reactor treating alcohol distillery wastewater, while the other reactor (R2) was inoculated with sludge from a full scale reactor treating paper mill wastewater. A 30h pH shock (pH 5) strongly affected the metal retention dynamics within the granular sludge bed in both reactors. Iron losses in soluble form with the effluent were considerable: 2.3 and 2.9% for R1 and R2, respectively, based on initial iron content in the reactors, while losses of cobalt and nickel in soluble form were limited. Sequential extraction of the metals from the sludge showed that cobalt, nickel, iron and sulfur were translocated from the residual to the organic/sulfide fraction during the pH shock in R2, increasing 34, 47, 109 and 41% in the organic/sulfide fraction, respectively. This is likely due to the modification of the iron sulfide precipitate stability, which influences the extractability of iron and trace metals. Such a translocation was not observed for the R1 sludge during the first 30h pH shock, but a second 4day pH shock induced significant losses of cobalt (18%), iron (29%) and sulfur (29%) from the organic/sulfide fraction, likely due to iron sulfide dissolution and concomitant release of cobalt. After the 30h pH shock, VFA accumulated in the R2 effluent, whereas both VFA and methanol accumulated in R1 after the 4day pH shock. The formed VFA, mainly acetate, were not converted to methane due to the loss of methanogenic activity of the sludge on acetate. The VFA accumulation gradually disappeared, which is likely to be related to out-competition of acetogens by methanogens. Zinc, copper and manganese supply did not have a clear effect on the acetate removal and methanol conversion, but zinc may have induced the onset of methanol degradation after day 152 in R1.     

The inhibitory effects and removal of dieldrin in continuous upflow anaerobic sludge blanket reactors

The inhibitory effects and removal efficiency of dieldrin (DLD) in anaerobic reactors were investigated. Anaerobic toxicity assay (ATA) experiments conducted in batch reactors revealed that 30 mg/l DLD had inhibitory effects on the unacclimated mixed anaerobic cultures. Continuous reactor experiments performed in a lab-scale two-stage upflow anaerobic sludge blanket (UASB) reactor system which was fed with ethanol as the sole carbon source, indicated that anaerobic granular cultures could be successfully acclimated to DLD. Chemical oxygen demand (COD) removal efficiencies were 88-92% for the two-stage system. The influent DLD concentration of 10 mg/l was removed by 44-86% and 86-94% in the second stage and overall UASB system, respectively. Biosorption of DLD on granular anaerobic biomass was found to be a significant mechanism for DLD removal in the UASB system. The maximum DLD loading rate and minimum HRT achievable for the first stage UASB reactor were 0.5 mg/lday (76 microg DLD/g VSS.day) and 10 h, respectively, which resulted in the overall COD removal efficiency of 85%.     

Degradation of 4-chlorophenol in UASB reactor under methanogenic conditions

Treatment of simulated wastewater containing 40 mg/l of 4-chlorophenol (4-CP) was carried out in an upflow anaerobic sludge blanket (UASB) reactor under methanogenic condition. The performance of this test UASB reactor was evaluated in terms of 4-CP removal. Hydraulic retention time (HRT) and substrate:co-substrate ratio for the 4-CP removal was optimized by varying the influent flow rate (13-34.7 ml/min) and sodium acetate concentration (2-5 g/l), respectively. A control UASB reactor, which was not exposed to 4-CP was also operated under similar conditions. Organic loading rate (OLR) was varied in the range of 2-5.3 kg/m(3)/d and 1.7-4.2 kg/m(3)/d, respectively, for HRT and substrate:co-substrate ratio studies, respectively. The optimum HRT and substrate:co-substrate ratio for the removal of 4-CP was 12h and 1:75, respectively. Removal of 4-CP achieved at optimum HRT and substrate:co-substrate ratio was 88.3+/-0.7%. Removal of 4-CP occurred through dehalogenation and caused increase in chloride ion concentration in the effluent by 0.23-0.27 mg/mg 4-CP removed. The ring cleavage test showed the ortho mode of ring cleavage of 4-CP. Change in the elemental composition of the anaerobic biomass of UASB reactors was observed during the study period. Concentration of Ca(2+) increased in the biomass and this could be attributed to the biosoftening. Specific methanogenic activity of the sludge of control and test UASB reactor was 0.832 g CH(4) COD/g VSS d and 0.694 g CH(4) COD/g VSS d, respectively.     

Thermophilic (55 degrees C) conversion of methanol in methanogenic-UASB reactors: influence of sulphate on methanol degradation and competition

Two upflow sludge bed reactors (UASB) were operated for 80 days at 55 degrees C with methanol as the substrate with an organic loading rate (OLR) of about 20 g CODl(-1) per day and a hydraulic retention time (HRT) of 10 h. One UASB was operated without sulphate addition (control reactor-R1) whereas the second was fed with sulphate at a COD:SO4(2-) ratio of 10 (sulphate-fed reactor-R2), providing an influent sulphate concentration of 0.6 g l(-1). For both reactors, methanogenesis was the dominant process with no considerable accumulation of acetate. The methanol removal averaged 93% and 83% for R1 and R2, respectively, and total sulphate removal was achieved in the latter. The pathway of methanol conversion for both sludges was investigated by measuring the fate of carbon in the presence and absence of bicarbonate or specific inhibitors for a sludge sample collected at day 72. In both sludges, about 70% of the methanol was syntrophically converted to methane and/or sulphide, via the intermediate H2/CO2. A strong competition between methanogens and sulphidogens took place in the R2 sludge with half of the methanol-COD being used by methane-producing bacteria and the other half by sulphate-reducing bacteria. Acetate was not an important intermediate for both sludges, and played a slightly more important role for the sulphate-adapted sludge (R2), sustained by the higher amount of bicarbonate produced during sulphate-reduction. The pathway study indicates that, although acetate does not represent an important intermediate, the system is susceptible to its accumulation.     

Evaluation of UASB reactor performance during start-up operation using synthetic mixed-acid waste

A start-up experiment was performed in a laboratory-scale, upflow anaerobic sludge blanket (UASB) reactor using seed sludge from a domestic waste treatment plant at 3.8-33.3gCODl(-1)day(-1) loading rates. Analysis over the height of the reactor with time showed that the VSS in the reactor was initially differentiated into active and non-active biomass at increasing gas production and upflow velocities, and specific update rates of the volatile fatty acids (VFA) components were pronounced at the bottom 10% of the reactor. During start-up, specific methanogenic activity and chemical oxygen demand (COD) uptake rate increased from 0.075 to 0.75gCOD-CH(4)(gVSS)(-1)day(-1) and from 0.08 to 0.875gCOD removed (gVSS)(-1)day(-1), respectively. When seed sludge from a distillery waste treatment plant was used, improved performance due to a predominance of active biomass was evident when the loading rate was increased from 9.4 to 28.7gCODl(-1)day(-1). The proposed start-up evaluation is an effective tool to successfully monitor performance of UASB reactors.     

Continuous detoxification, transformation, and degradation of nitrophenols in upflow anaerobic sludge blanket (UASB) reactors

The anaerobic transformation and degradation of nitrophenols by granular sludge was investigated in upflow anaerobic sludge blanket (UASB) reactors continuously fed with a volatile fatty acid (VFA) mixture as the primary substrate. During the start-up, subtoxic concentrations of 2-nitrophenol (2-NP), 4-nitrophenol (4-NP), and 2, 4-dinitrophenol (2, 4-DNP) were utilized. 4-NP and 2, 4-DNP were readily converted to the corresponding aromatic amine; whereas 2-NP was converted to nonaromatic products via intermediate formation of 2-aminophenol (2-AP). These conversions led to a dramatic detoxification of the mononitrophenols because the reactors treated the nitrophenolics at the concentrations which were over 25 times higher than those that caused severe inhibition. VFA removal efficiencies greater than 99% were achieved in both reactors at loading rates greater than 11.4 g COD per liter of reactor volume per day even at volumetric loading of mononitrophenols up to 910 mg/L . d.The sludges obtained from each of the reactors at the end of the continuous experiments were assayed for their specific nitrophenol reducing activity in the presence of different primary substrates. Reduction rates of 45 and 26 mg/g volatile suspended solids per day were observed for 2-NP and 4-NP, respectively, when utilizing the VFA mixture as primary substrate. Hydrogen, an interspecies-reduced compound, and substrates that provide interspecies-reducing equivalents-such as butyrate, propionate, and ethanol stimulated nitrophenol reduction, whereas acetate and methanol did not. Anaerobic batch biodegradability tests with the 2-NP-adapted sludge revealed that its corresponding aromatic amine, 2-AP, was degraded to methane at a specific rate of 14.5 mg/g VSS . d. Acetate was observed to be the major intermediate during 2-AP degradation in the presence of a specific methanogenic inhibitor 2-bromoethanesulfonate. The results of this study indicate that UASB reactors can be applied to rapidly detoxify and, under certain circumstances, degrade nitroaromatic compounds. (c) 1996 John Wiley & Sons, Inc.     

Enhanced biodegradation of hexachlorocyclohexane in upflow anaerobic sludge blanket reactor using methanol as an electron donor

Anaerobic dechlorination of technical grade hexachlorocyclohexane (THCH) was studied in a continuous upflow anaerobic sludge blanket (UASB) reactor with methanol as a supplementary substrate and electron donor. A reactor without methanol served as the experimental control. The inlet feed concentration of THCH in both the experimental and the control UASB reactor was 100 mg l(-1). After 60 days of continuous operation, the removal of THCH was >99% in the methanol-supplemented reactor as compared to 20-35% in the control reactor. THCH was completely dechlorinated in the methanol fed reactor at 48 h HRT after 2 months of continuous operation. This period was also accompanied by increase in biomass in the reactor, which was not observed in the experimental control. Batch studies using other supplementary substrates as well as electron donors namely acetate, butyrate, formate and ethanol showed lower % dechlorination (<85%) and dechlorination rates (<3 mg g(-1)d(-1)) as compared to methanol (98%, 5 mg g(-1)d(-1)). The optimum concentration of methanol required, for stable dechlorination of THCH (100 mg l(-1)) in the UASB reactor, was found to be 500 mg l(-1). Results indicate that addition of methanol as electron donor enhances dechlorination of THCH at high inlet concentration, and is also required for stable UASB reactor performance.     

Statistical modeling and optimization of biomass granulation and COD removal in UASB reactors treating low strength wastewaters

The aim of this work was to study the influence of influent chemical oxygen demand (COD), upflow velocity of wastewater, and cationic polymer additives in inoculum, on biomass granulation and COD removal efficiency in upflow anaerobic sludge blanket (UASB) reactor for treating low strength wastewater. Statistical models were formulated based on these three variables to optimize the biomass granulation and COD removal efficiency in UASB reactors using a two-level, full factorial design. For the thick inoculum used in this study, having suspended solids (SS) >80 g/l and volatile suspended solids (VSS) to SS ratio <0.3, cationic polymer additives in the inoculum showed adverse effect on biomass granulation and COD removal efficiency. It is concluded that for such thick inoculum, granulation can be obtained while treating low strength wastewaters in UASB reactor by selecting proper combination of influent COD and liquid upflow velocity so as to represent the organic loading rate (OLR) greater than 1.0 kg COD/m(3) d. Validation of model predictions for treatment of synthetic wastewater and actual sewage reveals the efficacy of these models for enhancing granulation and COD removal efficiency.     

Long-term adaptation of methanol-fed thermophilic (55 °C) sulfate-reducing reactors to NaCl

A laboratory-scale upflow anaerobic sludge bed (UASB) reactor was operated during 273 days at increasing NaCl concentrations (0.5–12.5 g NaCl l^–1) to assess whether the stepwise addition of the salt NaCl results in the acclimation of that sludge. The 6.5-l thermophilic (55 °C), sulfidogenic [a chemical oxygen demand (COD) to SO₄^2– ratio of 0.5] UASB reactor operated at an organic loading rate of 5 g COD l^–1 day^–1, a hydraulic retention time of 10 h and was fed with methanol as the sole electron donor. The results show that the adaptation of the thermophilic, sulfidogenic methanol-degrading biomass to a high osmolarity environment is unlikely to occur. Sulfide was the main mineralization product from methanol degradation, regardless of the NaCl concentration added to the influent. However, sulfide production in the reactor steadily decreased after the addition of 7.5 g NaCl l^–1, whereas acetate production was stimulated at that influent NaCl concentration. Batch tests performed with sludge harvested from the UASB reactor when operating at different influent salinities confirmed that acetate is the main metabolic product at NaCl concentrations higher than 12.5 g l^–1. The apparent order of NaCl toxicity towards the different trophic groups was found to be: sulfate-reducing bacteria > methane-producing archaea > acetogenic bacteria.     

The influence of anaerobic pretreatment on the nitrogen removal from biosynthetic pharmaceutical wastewaters

The C:N ratio of the pharmaceutical wastewaters is usually suitable for a combination of the anaerobic pretreatment with the high COD removal and aerobic posttreatment with the efficient biological N removal. This kind of anaerobic-aerobic process was tested in semipilot scale by using a UASB reactor and an activated sludge system with a predenitrification (total volume 100 1). It was found that at a total HRT of 2.3 days an average of 97.5% of COD and 73.5% of total N was removed. The UASB reactor was operated at 30°C with a volumetric loading rate of 8.7 kg.m^-3.d^-1, the efficiency of COD removal was 92.2%. The processes, which take part in the biological removal of nitrogen, especially the nitrification, were running with lower rates than usually observed in aerobic treatment systems.Abbreviations AAO anaerobic anoxic oxic configuration - AOO anaerobic oxic oxic configuration - B _V volumetric organic loading rate (kg COD.m^-3. d^-1) - dB _x specific COD removal rate (mg COD. g^-1 VSS. d^-1) - DNR denitrification rate (mg N–NO₃. g^-1 VSS. h^-1) - E_COD efficiency of COD removal (%) - HRT hydraulic retention time (d) - NR nitrification rate (mg N–NO₃. g^-1 VSS. h^-1) - R recirculation ratio (%) - SBP specific biogas production (m³.kg^-1 removed COD) - SRT solids retention time; sludge age (d) - SS suspended solids (g.1^-1) - UASB upflow anaerobic sludge blanket reactor - VSS volatile suspended solids (g.1^-1)     

Start-up alternatives and performance of an UASB pilot plant treating diluted municipal wastewater at low temperature

Different start-up procedures of an upflow anaerobic sludge bed (UASB) digester were carried out. Start-up without inoculum (experiment A) was delayed for about 120 day. The digester reached 75-85% total suspended solids (TSS) removal, 54-58% total chemical oxygen demand (TCOD) removal and 63-73% biological oxygen demand (BOD5) removal at influent concentrations of 240-340 mg TCODil-1, temperatures of 13.5-15 degrees C and hydraulic retention times (HRT) of 10-11 h. Digested sludge was used as inoculum in experiment B. After the start-up period of 75 days, digester efficiencies were 58%, 41% and 54% for TSS, TCOD and BOD5 removal, respectively, working at 169 mg TCODil-1, temperature of 14 degrees C and HRT of 11 h. The sludge bed developed and stabilised quickly when using a hydraulically adapted inoculum (experiment C), but TCOD and BOD5 removals remained low and volatile fatty acids (VFA) accumulated in the effluent.     

Performance of upflow anaerobic sludge blanket (UASB) reactor treating wastewaters containing carbon tetrachloride

The anaerobic biodegradation of carbon tetrachloride (CT) was investigated during the granulation process by reducing the hydraulic retention time, increasing the chemical oxygen demand (COD) and CT loadings in a 2l laboratory-scale upflow anaerobic sludge blanket (UASB) reactor. Anaerobic unacclimated sludge and glucose were used as seed and primary substrate, respectively. Granules were developed 4 weeks after start-up, which grew at an accelerated rate for 8 months, and then became fully grown. The effect of operational parameters such as influent CT concentrations, COD, CT loading, food to biomass ratio and specific methanogenic activity (SMA) were also considered during granulation. The granular sludge cultivated had a maximum diameter of 2.1 mm and SMA of 1.6 g COD/g total suspended solid (TSS) day. COD and CT removal efficiencies of 92 and 88% were achieved when the reactor was firstly operating at CT and COD loading rates of 17.5 mg/l day and 12.5 g/l day, respectively. This corresponds to hydraulic retention time of 0.28 day and food to biomass ratio of 0.5 g COD/g TSS day. Kinetic coefficients of maximum specific substrate utilization rate, half velocity coefficient, growth yield coefficient and decay coefficient were determined to be 2.4 × 10^–3 mg CT/TSS day^–1, 1.37 mg CT/l, 0.69 mg TSS/mg CT and 0.046 day^–1, respectively for CT biotransformation during granulation.     

PVA-gel beads enhance granule formation in a UASB reactor

PVA-gel beads were used as a biocarrier in a lab-scale UASB reactor treating synthetic wastewater composed of corn steep liquor (CSL) with the aim of evaluating its use as a growth nucleus to enhance granule formation. Over 117 days of operation, the organic loading rate was increased to 22.5kgCOD/m(3)/day with an influent COD of about 10.8g/L at an HRT of 12h with COD removal efficiencies greater than 87%. By the end of the study period, the PVA-gel turned black and granule formation was achieved as compared with the formation of much fewer natural granules without the PVA-gel nucleus. No filamentous bacteria were found on the surface or interior of the PVA-gel beads. The PVA-gel granules had an average settling velocity 200m/h (5cm/s), and a biomass attachment of 0.93g VSS/g PVA-gel. The required time for formation of PVA-gel granules was thus demonstrated to be shorter than that of ordinary sludge granules under the experimental conditions used in this study.