Performance of upflow anaerobic sludge blanket (UASB) reactor treating wastewaters containing carbon tetrachloride

The anaerobic biodegradation of carbon tetrachloride (CT) was investigated during the granulation process by reducing the hydraulic retention time, increasing the chemical oxygen demand (COD) and CT loadings in a 2l laboratory-scale upflow anaerobic sludge blanket (UASB) reactor. Anaerobic unacclimated sludge and glucose were used as seed and primary substrate, respectively. Granules were developed 4 weeks after start-up, which grew at an accelerated rate for 8 months, and then became fully grown. The effect of operational parameters such as influent CT concentrations, COD, CT loading, food to biomass ratio and specific methanogenic activity (SMA) were also considered during granulation. The granular sludge cultivated had a maximum diameter of 2.1 mm and SMA of 1.6 g COD/g total suspended solid (TSS) day. COD and CT removal efficiencies of 92 and 88% were achieved when the reactor was firstly operating at CT and COD loading rates of 17.5 mg/l day and 12.5 g/l day, respectively. This corresponds to hydraulic retention time of 0.28 day and food to biomass ratio of 0.5 g COD/g TSS day. Kinetic coefficients of maximum specific substrate utilization rate, half velocity coefficient, growth yield coefficient and decay coefficient were determined to be 2.4 × 10^–3 mg CT/TSS day^–1, 1.37 mg CT/l, 0.69 mg TSS/mg CT and 0.046 day^–1, respectively for CT biotransformation during granulation.     

Statistical modeling and optimization of biomass granulation and COD removal in UASB reactors treating low strength wastewaters

The aim of this work was to study the influence of influent chemical oxygen demand (COD), upflow velocity of wastewater, and cationic polymer additives in inoculum, on biomass granulation and COD removal efficiency in upflow anaerobic sludge blanket (UASB) reactor for treating low strength wastewater. Statistical models were formulated based on these three variables to optimize the biomass granulation and COD removal efficiency in UASB reactors using a two-level, full factorial design. For the thick inoculum used in this study, having suspended solids (SS) >80 g/l and volatile suspended solids (VSS) to SS ratio <0.3, cationic polymer additives in the inoculum showed adverse effect on biomass granulation and COD removal efficiency. It is concluded that for such thick inoculum, granulation can be obtained while treating low strength wastewaters in UASB reactor by selecting proper combination of influent COD and liquid upflow velocity so as to represent the organic loading rate (OLR) greater than 1.0 kg COD/m(3) d. Validation of model predictions for treatment of synthetic wastewater and actual sewage reveals the efficacy of these models for enhancing granulation and COD removal efficiency.     

Anaerobic granule development for removal of pentachlorophenol in an upflow anaerobic sludge blanket (UASB) reactor

The granulation process using synthetic wastewater containing pentachlorophenol (PCP) in four 1.1 l laboratory scale upflow anaerobic sludge blanket (UASB) reactors was studied, and the anaerobic biotransformation of PCP during the granulation process investigated. After 110 days granular sludge was developed and up to 160 and 180 mg/l of PCP was added into the reactors R1 and R2, respectively, when they were inoculated with acclimated anaerobic sludge from an anaerobic digester of a citric acid plant. The inoculum was predominately composed of bacilli and filamentous bacteria. Granulation did not occur in reactors R3 and R4 which were inoculated with acclimated anaerobic sludge from aerobic sludge of the municipal sewage treatment plant which consisted mainly of cocci. Despite similar bacilli in the granule, the filamentous bacteria from reactor R1 were thicker than those of reactor R2. The granular sludge had a maximum diameter of 2.5 and 2.2 mm, and SMA of 1.44 and 1.32 gCOD/gTVS per day for reactors R1 and R2, respectively. Over 98% chemical oxygen demand (COD) removal rate and 99% of PCP removal rate were achieved when reactors R1 and R2 were operated at PCP and COD loading rates of 150 and 7.5 g/l per day, respectively. H₂-producing acetogens were the dominant anaerobes in the granular sludge.     

Effect of feed composition and upflow velocity on aggregate characteristics in anaerobic upflow reactors

Two upflow anaerobic hybrid reactors treated lactose and a mixture of ethanol, propionate and butyrate, respectively, at a volumetric loading rate of 3.7 kg chemical oxygen demand (COD) m⁻³day⁻¹, a hydraulic retention time of 5 days and a liquid upflow velocity of 0.01 m/h. Under steady-state conditions, the lactose-fed sludge had much higher (20%–100%) specific methanogenic conversion rates than the volatile-fatty acid␣(VFA)/ethanol-fed sludge for all substrates tested, including VFA. In both reactors, a flocculant sludge developed, although a much higher content of extracellular polysaccharide was measured in the lactose-fed sludge [1900 μg compared to 305 μg uronic acid/g volatile suspended solids (VSS)]. When the liquid upflow velocity of a third, VFA/ethanol-fed reactor was increased to 0.5 m/h, granulation of the sludge occurred, accompanied by a large increase (200%–500%) in the specific methanogenic conversion rates for the syntrophic and methanogenic substrates studied. Granulation reduced the susceptibility of the sludge to flotation. Glucose was degraded at a high rate (100 mg glucose gVSS⁻¹h⁻¹) by the sludge from the third reactor, despite not having been exposed to a sugar-containing influent for 563␣days. Received: 7 June 1996 / Received revision: 23 September 1996 / Accepted: 29 September 1996     

Biogas production from supernatant of hydrothermally treated municipal sludge by upflow anaerobic sludge blanket reactor

The supernatant of hydrothermally treated sludge was treated by an upflow anaerobic sludge blanket (UASB) reactor for a 550-days running test. The hydrothermal parameter was 170 °C for 60 min. An mesophilic 8.6 L UASB reactor was seeded with floc sludge. The final organic loading rate (OLR) could reach 18 kg COD/m³ d. At the initial stage running for 189 days, the feed supernatant was diluted, and the OLR reached 11 kg COD/m³ d. After 218 days, the reactor achieved a high OLR, and the supernatant was pumped into the reactor without dilution. The influent COD fluctuated from 20,000 to 30,000 mg/L and the COD removal rate remained at approximately 70%. After 150 days, granular sludge was observed. The energy balance calculation show that heating 1.0 kg sludge needs 0.34 MJ of energy, whereas biogas energy from the supernatant of the heated sludge is 0.43 MJ.     

Improved performance of upflow anaerobic sludge blanket (UASB) reactors by operating alternatives

Summary The efficient operation of UASB reactors treating complex soluble wastewater containing high protein and lipid content was attempted by mixing in different modes. Higher superficial flow rate increased COD removal efficiency, sludge retainment, and methane content in biogas not only in the start-up period but also at high volumetric loading rates. However, formation of sludge particles in larger size was hindered by increased upflow liquid velocity.     

The inhibitory effects and removal of dieldrin in continuous upflow anaerobic sludge blanket reactors

The inhibitory effects and removal efficiency of dieldrin (DLD) in anaerobic reactors were investigated. Anaerobic toxicity assay (ATA) experiments conducted in batch reactors revealed that 30 mg/l DLD had inhibitory effects on the unacclimated mixed anaerobic cultures. Continuous reactor experiments performed in a lab-scale two-stage upflow anaerobic sludge blanket (UASB) reactor system which was fed with ethanol as the sole carbon source, indicated that anaerobic granular cultures could be successfully acclimated to DLD. Chemical oxygen demand (COD) removal efficiencies were 88-92% for the two-stage system. The influent DLD concentration of 10 mg/l was removed by 44-86% and 86-94% in the second stage and overall UASB system, respectively. Biosorption of DLD on granular anaerobic biomass was found to be a significant mechanism for DLD removal in the UASB system. The maximum DLD loading rate and minimum HRT achievable for the first stage UASB reactor were 0.5 mg/lday (76 microg DLD/g VSS.day) and 10 h, respectively, which resulted in the overall COD removal efficiency of 85%.     

Effects of cationic polymer on performance of UASB reactors treating low strength wastewater

The effect of cationic polymer additives on biomass granulation and COD removal efficiency had been examined in lab-scale upflow anaerobic sludge blanket (UASB) reactors, treating low strength synthetic wastewater (COD 300-630 mg/l). Under identical conditions, two reactors were operated with and without polymer additives in inoculum under four different organic loading rates (OLRs). The optimum polymer dose was adopted based upon the results of jar test and settling test carried out with inoculum seed sludge. With the use of thick inoculum, SS greater than 110 g/l and VSS/SS ratio less than 0.3, granulation was observed in UASB reactor treating synthetic wastewater as well as actual sewage, when OLR was greater than 1.0 kg COD/m(3) d. Polymer additive with such thick inoculum was observed to deteriorate percentage granules and COD removal efficiency compared to inoculum without polymer additives. At OLR less than 1.0 kg COD/m(3) d, proper granulation could not be achieved in both the reactors inoculated with and without polymer additive. Also, under this low loading, drastic reduction in COD removal efficiency was observed with polymer additives in inoculum. Hence, it is rational to conclude that biomass granulation for treatment of low strength biodegradable wastewater depends on the applied loading rate and selection of thick inoculum sludge.     

Methanogenic granular sludge formation in an upflow anaerobic sludge blanket reactir treating synthetic methanolic waste

A laboratory upflow anaerobic sludge blanket reactor, seeded with fine, suspended, bacterial floc with 1.76 g volatile suspended solids/l, was used to treat synthetic methanolic waste. After 180 days of continuous peration, granular sludge with discrete granules of 1 to 2 mm diam. was formed, with 52 g volatile suspended solids/l. Granules were brown, relatively soft and had a settling velocity of 1.61 cm/s. Extracellular polymeric matter extracted from the granular sludge had high carbohydrate content but low nucleic acid content. The ash of the granular sludge contained Na⁺, K⁺ and Mg²⁺ up to 15.0, 11.7 and 3.75 mg/g, respectively. Scanning and transmission electron microscopy revealed that the granular sludge was dominated by methanogens resembling Methanosarcina.The authors are with the Department of Environmental Engineering, Faculty of Engineering, Osaka University, 2-1 Yamadaoka, Suita, Osaka 565, Japan     

Biodegradation of tech-hexachlorocyclohexane in a upflow anaerobic sludge blanket (UASB) reactor

Biodegradability of technical grade hexachlorocyclohexane (tech-HCH) was studied in an upflow anaerobic sludge blanket reactor (UASB) under continuous mode of operation in concentration range of 100-200 mg/l and constant HRT of 48 h. At steady state operation more than 85% removal of tech-HCH (upto 175 mg/l concentration) and complete disappearance of beta-HCH was observed. Kinetic constants in terms of maximum specific tech-HCH utilization rate (k) and half saturation velocity constant (K(L)) were found to be 11.88 mg/g/day and 8.11 mg/g/day, respectively. The tech-HCH degrading seed preparation, UASB reactor startup and degradation in continuous mode of operation of the reactor is presented in this paper.     

Methane production from acetamide in an upflow anaerobic sludge-blanket reactor based on a synergistic association between an aerobic rod and methanogens

Acetamide degradation was investigated in a bench-scale upflow anaerobic sludge-blanket (UASB) reactor, successively fed with acetamide, acetate and acetamide, over a period of 343 days, at different hydraulic retention times (t _HR). The reactor was seeded with the sludge previously described [Guyot et al. (1994) Appl Microbiol Biotechnol, 42:452-456], in which methanogenesis from acetamide was performed through a synergistic relationship between an acetamide-degrading, aerobic rod and methanogens. When the reactor was fed acetamide, the chemical oxygen demand (COD) removal efficiency was 86% at volumetric loads less than 1.18 kg COD m^–3 day ^–1. At higher volumetric loads, the efficiency decreased markedly, e.g. 50.9% at a volumetric organic load of 3.39 kg COD m^–3 day^–1 (1 day t _HR) with an accumulation of both acetamide and acetate. The same reactor, when fed with acetate at t _HR 1 day, reached a high COD removal (99%). Evidence of the inhibition of acetate degradation by acetamide is presented. After a long period (135 days) without feeding the reactor with acetamide, the sludge reactor was still capable of degrading acetamide when this substrate was supplied again. It seems that the synergistic degradation of acetamide by aerobes and methanogens present in the UASB reactor sludge is stable over a long period (343 days), in spite of limiting concentrations of dissolved oxygen in the feed.     

Granulation of digested sewage sludge in mesophilic UASB reactors treating distillery waste waters from sugar cane molasses

Five 4.02-1 UASB (Upflow Anaerobic Sludge Blanket) reactors were continuously operated at 30°C under different hydrodynamic regimes for more than 120 days. The effect of the upflow liquid velocity (ULV) over the range of 0.25 to 2.0 m/h on the biological characteristics of the granules formed by treating vinasses (waste water of alcohol distilleries) from sugar cane molasses was investigated constantly maintaining the volumetric loading rate (VLR) (8 g COD/l · d). Granular sludge was found at all the ULV tested. The size, shape, etc., of the granules indicated that the ULV had a considerable effect on the sludge cultivated in this type of system, thereby acting as a selection process for the biomass. The best results in relation to the time of appearance, size, shape, consistence, stability, composition, and the accumulation were observed in the ULV range between 0.25 and 0.5 m/h. Microscopic studies of the granules using optical and epifluorescence microscopes and the scanning electron micrograph (SEM) showed a heterogeneous biomass and revealed the cell characteristics.     

Continuous anaerobic treatment of wastewaters containing formaldehyde and urea

The toxicity of formaldehyde (FA) in batch assays, using volatile fatty acids (VFA) as co-substrate, and the continuous anaerobic treatment of wastewaters containing FA in upflow anaerobic sludge blanket (UASB) reactors was investigated. In batch studies, FA exerted a 50% methanogenic toxicity on VFA at concentrations of around 100 mg/l, 2.5 times lower than values reported with sucrose. Although at FA concentrations higher than 200 mg/l methanogenesis was completely inhibited, a partial recovery of the bacterial activity was observed after 250 h when the FA had been removed from the medium. The continuous anaerobic degradation of FA at concentrations up to 2 g/l, using 1.6 g/l of glucose as co-substrate, was studied in a UASB reactor. A stable and efficient operation was observed at organic loading rates (OLR) of 6.0 g COD/l·d and with a COD/FA ratio as low as 1.4. A synthetic substrate with the same characteristics as the effluents produced during fibreboard adhesives manufacturing (based on urea-FA), i.e. 0.95 g FA/l and 0.35 g urea/l, was treated in a UASB reactor. The applied OLR and nitrogen loading rate (NLR) were 3.45 g COD/l·d and 0.58 g N/l·d, respectively. COD removal efficiencies were maintained at 90–95%, FA and urea being completely degraded.     

Thermophilic anaerobic treatment of sulphur rich forest industry wastewater

Thermophilic anaerobic treatment of sulphur-rich paper mill wastewater (0.8-3.1 gCOD/l, 340–850 mgSO₄/l; COD:SO₄ 3.4-5.3) was studied in three laboratory-scale, upflow anaerobic sludge blanket (UASB) reactors and in bioassays. The reactors were inoculated with non-adapted thermophilic granular sludge. In the bioassays, no inhibition of the inoculum was detected and about 62% COD removal (sulphide stripped) was obtained. About 70 to 80% of the removed COD was methanised. In the reactors, up to 60–74% COD removal (effluent sulphide stripped) was obtained at loading rates up to 10–30 kgCOD/m³d and hydraulic retention times down to 6 to 2 hours. The effluent total sulphide was up to 150–250 mg/l. Sulphide inhibition could not be confirmed from the reactor performances. The results from bioassays suggested that both the inoculum and sludge from the UASB reactor used acetate mainly for methane production, while sulphide was produced from hydrogen or its precursors.     

Flocculants effect in biomass retention in a UASB reactor treating dairy manure

The performance and biomass retention of an upflow anaerobic sludge bed (UASB) reactor treating liquid fraction of dairy manure has been investigated at several organic loading rates. Two identical UASB reactors were employed. The biomass of one UASB reactor (FBR) had previously been treated with a cationic polyacrylamide, the other reactor was operated as a control reactor (CR). At 3 and 2 days of HRT both reactors functioned similarly, but at 1.5 days HRT some differences were observed between both effluents. Mean COD(T) removal percentages were 83.4% and 76.5%; COD(VFA) values in effluents were 977 and 2682 mg l(-1) for the FBR and the CR respectively. The VSS initial value in both reactors was 25.66 g VSS, whereas after the experiment the quantities were 31.83 g VSS in the FBR and 23.18 g VSS in the CR reactors. Polymer addition resulted in a higher degree of biomass retention and better performance in the FBR reactor.     

Rapid granulation and sludge retention for tetrachloroethylene removal in an upflow anaerobic sludge blanket reactor

A laboratory scale upflow anaerobic sludge blanket (UASB) reactor was operated at 35 °C for over 200 days to investigate the granulation mechanism during tetrachloroethylene (TCE) biodegradation. Anaerobic, unacclimated sludge and glucose were used as seed and primary substrate, respectively. TCE-degrading granules developed after 1.5 months of start-up. They grew at an accelerated pace for 7 months. The TCE-degrading granules had a maximum diameter of 2.5 mm and specific methanogenic activity of 1.32 g chemical oxygen demand (COD) g^–1 total suspended solid (TSS) day^–1. 94% COD and 90% TCE removal efficiencies were achieved when the reactor was operating at loading rates as high as 160 mg TCE l^–1 day^–1 and 14 g COD l^–1 day^–1, after 230 days of continuous operation.     

Application of the upflow anaerobic sludge bed (UASB) process for treatment of complex wastewaters at low temperatures

The feasibility of the upflow anaerobic sludge bed (UASB) process for the treatment of potato starch wastewater at low ambient temperatures was demonstrated by operating two 5.65-L reactors at 14 degrees C and 20 degrees C, respectively. The organic space loading rates achieved in these laboratory-scale reactors were 3 kg COD/m(3)/day at 14 degrees C and 4-5 kg COD/m(3)/day at 20 degrees C. The corresponding sludge loading rates were 0.12 kg COD/kg VSS/day at 14 degrees C and 0.16-0.18 kg COD/kg VSS/day at 20 degrees C.These findings are of considerable practical importance because application of anaerobic treatment at low ambient temperatures will lead to considerable savings in energy needed for operating the process. As compared with various other anaerobic wastewater treatment processes, a granular sludge upflow process represents one of the best options developed so far. Although the overall sludge yield under psychrophilic conditions is slightly higher than under optimal mesophilic conditions, this doesn't seriously hamper the operation of the process. The extra sludge yield, due to accumulation of slowly hydrolyzing substrate ingredients, was 4.75% of the COD input at 14 degrees C and 1.22% of the COD input at 20 degrees C.     

Effects of alkalinity and co-substrate on the performance of an upflow anaerobic sludge blanket (UASB) reactor through decolorization of Congo Red azo dye

The effect of substrate (glucose) concentrations and alkalinitiy (NaHCO3) on the decolorization of a synthetic wastewater containing Congo Red (CR) azo dye was performed in an upflow anaerobic sludge blanket (UASB). Color removal efficiencies approaching 100% were obtained at glucose-COD concentrations varying between 0 and 3000 mg/l. The methane production rate and total aromatic amine (TAA) removal efficiencies were found to be 120 ml per day and 43%, respectively, while the color was completely removed during glucose-COD free operation of the UASB reactor. The complete decolorization of CR dye under co-substrate free operation could be attributed to TAA metabolism which may provide the electrons required for the cleavage of azo bond in CR dye exist in the UASB reactor. No significant differences in pH levels (6.6-7.4), methane production rates (2000-2700 ml/day) and COD removal efficiencies (82-90%) were obtained for NAHCO3 concentrations ranging between 550 and 3000 mg/l. However, decolorization efficiency remained at 100% with decreasing NaHCO3 concentrations as low as 250 mg/l in the feed. An alkalinity/COD ratio of 0.163 in the feed was suggested for simultaneous optimum COD and color removal.     

Anaerobic treatment of a chemical synthesis-based pharmaceutical wastewater in a hybrid upflow anaerobic sludge blanket reactor

In this study, performance of a lab-scale hybrid up-flow anaerobic sludge blanket (UASB) reactor, treating a chemical synthesis-based pharmaceutical wastewater, was evaluated under different operating conditions. This study consisted of two experimental stages: first, acclimation to the pharmaceutical wastewater and second, determination of maximum loading capacity of the hybrid UASB reactor. Initially, the carbon source in the reactor feed came entirely from glucose, applied at an organic loading rate (OLR) 1 kg COD/m(3) d. The OLR was gradually step increased to 3 kg COD/m(3) d at which point the feed to the hybrid UASB reactor was progressively modified by introducing the pharmaceutical wastewater in blends with glucose, so that the wastewater contributed approximately 10%, 30%, 70%, and ultimately, 100% of the carbon (COD) to be treated. At the acclimation OLR of 3 kg COD/m(3) d the hydraulic retention time (HRT) was 2 days. During this period of feed modification, the COD removal efficiencies of the anaerobic reactor were 99%, 96%, 91% and 85%, and specific methanogenic activities (SMA) were measured as 240, 230, 205 and 231 ml CH(4)/g TVS d, respectively. Following the acclimation period, the hybrid UASB reactor was fed with 100% (w/v) pharmaceutical wastewater up to an OLR of 9 kg COD/m(3) d in order to determine the maximum loading capacity achievable before reactor failure. At this OLR, the COD removal efficiency was 28%, and the SMA was measured as 170 ml CH(4)/g TVS d. The hybrid UASB reactor was found to be far more effective at an OLR of 8 kg COD/m(3) d with a COD removal efficiency of 72%. At this point, SMA value was 200 ml CH(4)/g TVS d. It was concluded that the hybrid UASB reactor could be a suitable alternative for the treatment of chemical synthesis-based pharmaceutical wastewater.     

Application of polyethylene glycol immobilized Clostridium sp. LS2 for continuous hydrogen production from palm oil mill effluent in upflow anaerobic sludge blanket reactor

A novel polyethylene glycol (PEG) gel was fabricated and used as a carrier to immobilize Clostridium sp. LS2 for continuous hydrogen production in an upflow anaerobic sludge blanket (UASB) reactor. Palm oil mill effluent (POME) was used as the substrate carbon source. The optimal amount of PEG-immobilized cells for anaerobic hydrogen production was 12% (w/v) in the UASB reactor. The UASB reactor containing immobilized cells was operated at varying hydraulic retention times (HRT) that ranged from 24 to 6 h at 3.3 g chemical oxygen demand (COD)/L/h organic loading rate (OLR), or at OLRs that ranged from 1.6 to 6.6 at 12 h HRT. The best volumetric hydrogen production rate of 336 mL H₂/L/h (or 15.0 mmol/L/h) with a hydrogen yield of 0.35 L H₂/g COD_removed was obtained at a HRT of 12 h and an OLR of 5.0 g COD/L/h. The average hydrogen content of biogas and COD reduction were 52% and 62%, respectively. The major soluble metabolites during hydrogen fermentation were butyric acid followed by acetic acid. It is concluded that the PEG-immobilized cell system developed in this work has great potential for continuous hydrogen production from real wastewater (POME) using the UASB reactor.