Continuous bio-catalytic conversion of sugar mixture to acetone–butanol–ethanol by immobilized <Emphasis Type="Italic">Clostridium acetobutylicum</Emphasis> DSM 792

Continuous production of acetone, n-butanol, and ethanol (ABE) was carried out using immobilized cells of Clostridium acetobutylicum DSM 792 using glucose and sugar mixture as a substrate. Among various lignocellulosic materials screened as a support matrix, coconut fibers and wood pulp fibers were found to be promising in batch experiments. With a motive of promoting wood-based bio-refinery concept, wood pulp was used as a cell holding material. Glucose and sugar mixture (glucose, mannose, galactose, arabinose, and xylose) comparable to lignocellulose hydrolysate was used as a substrate for continuous production of ABE. We report the best solvent productivity among wild-type strains using column reactor. The maximum total solvent concentration of 14.32 g L⁻¹ was obtained at a dilution rate of 0.22 h⁻¹ with glucose as a substrate compared to 12.64 g L⁻¹ at 0.5 h⁻¹ dilution rate with sugar mixture. The maximum solvent productivity (13.66 g L⁻¹ h⁻¹) was obtained at a dilution rate of 1.9 h⁻¹ with glucose as a substrate whereas solvent productivity (12.14 g L⁻¹ h⁻¹) was obtained at a dilution rate of 1.5 h⁻¹ with sugar mixture. The immobilized column reactor with wood pulp can become an efficient technology to be integrated with existing pulp mills to convert them into wood-based bio-refineries.     

Butanol production by Clostridium acetobutylicum in a continuous packed bed reactor

In this study, we report on a butanol production process by immobilized Clostridium acetobutylicum in a continuous packed bed reactor (PBR) using Tygon^® rings as a carrier. The medium was a solution of lactose (15–30 g/L) and yeast extract (3 g/L) to emulate the cheese whey, an abundant lactose-rich wastewater. The reactor was operated under controlled conditions with respect to the pH and to the dilution rate. The pH and the dilution rate ranged between 4 and 5, the dilution rate between 0.54 and 2.4 h^?1 (2.5 times the maximum specific growth rate assessed for suspended cells). The optimal performance of the reactor was recorded at a dilution rate of 0.97 h^?1: the butanol productivity was 4.4 g/Lh and the selectivity of solvent in butanol was 88%_w.     

Continuous acetone-butanol-ethanol fermentation using SO2-ethanol-water spent liquor from spruce

SO₂–ethanol–water (SEW) spent liquor from spruce chips was successfully used for batch and continuous production of acetone, butanol and ethanol (ABE). Initially, batch experiments were performed using spent liquor to check the suitability for production of ABE. Maximum concentration of total ABE was found to be 8.79 g/l using 4-fold diluted SEW liquor supplemented with 35 g/l of glucose. The effect of dilution rate on solvent production, productivity and yield was studied in column reactor consisting of immobilized Clostridium acetobutylicum DSM 792 on wood pulp. Total solvent concentration of 12 g/l was obtained at a dilution rate of 0.21 h⁻¹. The maximum solvent productivity (4.86 g/l h) with yield of 0.27 g/g was obtained at dilution rate of 0.64 h⁻¹. Further, to increase the solvent yield, the unutilized sugars were subjected to batch fermentation.     

Acetone–butanol–ethanol production with high productivity using Clostridium acetobutylicum BKM19

Conventional acetone–butanol–ethanol (ABE) fermentation is severely limited by low solvent titer and productivities. Thus, this study aims at developing an improved Clostridium acetobutylicum strain possessing enhanced ABE production capability followed by process optimization for high ABE productivity. Random mutagenesis of C. acetobutylicum PJC4BK was performed by screening cells on fluoroacetate plates to isolate a mutant strain, BKM19, which exhibited the total solvent production capability 30.5% higher than the parent strain. The BKM19 produced 32.5 g L^?1 of ABE (17.6 g L^?1 butanol, 10.5 g L^?1 ethanol, and 4.4 g L^?1 acetone) from 85.2 g L^?1 glucose in batch fermentation. A high cell density continuous ABE fermentation of the BKM19 in membrane cell‐recycle bioreactor was studied and optimized for improved solvent volumetric productivity. Different dilution rates were examined to find the optimal condition giving highest butanol and ABE productivities. The maximum butanol and ABE productivities of 9.6 and 20.0 g L^?1 h^?1, respectively, could be achieved at the dilution rate of 0.85 h^?1. Further cell recycling experiments were carried out with controlled cell‐bleeding at two different bleeding rates. The maximum solvent productivities were obtained when the fermenter was operated at a dilution rate of 0.86 h^?1 with the bleeding rate of 0.04 h^?1. Under the optimal operational condition, butanol and ABE could be produced with the volumetric productivities of 10.7 and 21.1 g L^?1 h^?1, and the yields of 0.17 and 0.34 g g^?1, respectively. The obtained butanol and ABE volumetric productivities are the highest reported productivities obtained from all known‐processes. Biotechnol. Bioeng. 2013; 110: 1646–1653. © 2013 Wiley Periodicals, Inc.     

Production of butanol and isopropanol with an immobilized <Emphasis Type="Italic">Clostridium</Emphasis>

Clostridium beijerinckii optinoii is a Clostridium species that produces butanol, isopropanol and small amounts of ethanol. This study compared the performances of batch and continuous immobilized cell fermentations, investigating how media flow rates and nutritional modification affected solvent yields and productivity. In 96-h batch cultures, with 80 % of the 30 g L^?1 glucose consumed in synthetic media, solvent concentration was 9.45 g L^?1 with 66.0 % as butanol. In a continuous fermentation using immobilized C. beijerinckii optinoii cells, also with 80 % of 30 g L^?1 glucose utilization, solvent productivity increased to 1.03 g L^?1 h^?1. Solvent concentration reached 12.14 g L^?1 with 63.0 % as butanol. Adjusting the dilution rate from 0.085 to 0.050 h^?1 to allow extended residence time in column was required when glucose concentration in fresh media was increased from 30 to 50 g L^?1. When acetate was used to improve the buffer capacity in media, the solvent concentration reached 12.70 on 50 g L^?1 glucose. This continuous fermentation using immobilized cells showed technical feasibility for solvent production.     

Metabolic,physiological and kinetic aspects of the alcoholic fermentation of whey permeate by Kluyveromyces fragilis NRRL 665 and Kluyveromyces lactis NCYC 571

Optimum growth conditions for the fermentation of non-concentrated whey permeate by Kluyveromyces fragilis NRRL 665 have been defined. Use of 3.75 g yeast extract l^?1, a growth temperature of 38°C and a pH of 4.0 allowed a maximum productivity of 5.23 g ethanol l^?1 h^?1 in continuous culture with a yield 91% of theoretical. Complete batch fermentation of permeate with 100 g lactose l^?1 was possible with a maximum specific growth rate of 0.276 h^?1 without any change in ethanol yield. Fermentation of concentrated permeate resulted, however, in a general decrease of specific substrate consumption rate, demonstrated by the inability to completely convert an initial 90 or 150 g lactose l^?1 in continuous culture, even at dilution rates as low as 0.05 and 0.08 h^?1, respectively. The decrease could be related to substrate inhibition, to an increase in osmotic pressure caused by lactose and salts, and to ethanol inhibition of both alcohol and biomass yield. The decrease in specific productivity could be counterbalanced by use of high cell density cultures, obtained by cell recycle of K. fragilis. Fermentation of a non-concentrated permeáte at a dilution rate of 1 h^?1 resulted in a productivity of 22 g l^?1 h^?1 at 22 g ethanol l^?1. Cell recycle using flocculating Kluyveromyces lactis NCYC 571 was also tested. With this strain a productivity of 9.3 g l^?1 h^?1 at 45 g product l^?1 was attained at a dilution rate of 0.2 h^?1, with an initial lactose concentration of 95 g l^?1.     

Continuous cultivation of Lactobacillus brevis NCL912 for production of gamma-aminobutyric acid

A continuous cultivation method for Lactobacillus brevis NCL912 to synthesize gamma-aminobutyric acid was developed in this work. Different dilution rates were evaluated for obtaining steady state in continuous cultivation. The results showed that steady state could be achieved at dilution rates from 0.08 to 0.12 h^?1. The highest gamma-aminobutyric acid productivity (5.11 g L^?1?h^?1) was obtained at dilution rate of 0.09 h^?1. The kinetic models were established for continuous gamma-aminobutyric acid production by using the Monod equation for microbial growth, and the Luedeking–Piret equation for product formation. The microbial growth and product formation can be described by equations $ \mu = {{{0.1234{C_S}}} \left/ {{\left( {0.9338+{C_S}} \right)}} \right.} $ and $ {Q_P}=6.86\,\mathrm{g}\,{{\mathrm{g}}^{-1 }}\mathrm{cell}\,{{\mathrm{h}}^{-1 }} $ , respectively. The production of gamma-aminobutyric acid by L. brevis NCL912 was non-growth-associated.     

Nisin production in a chitin-including continuous fermentation system with Lactococcus lactis displaying a cell wall chitin-binding domain

The limiting factors in the continuous production of nisin are high amount of biomass loss and low dilution rate application. In this study, a chitin-including continuous nisin fermentation system (CICON-FER) was constructed for high volumetric nisin production using nisin producer L. lactis displaying cell wall chitin-binding domain (ChBD) together with chitin in the reactor. In this respect, the highest binding conditions of relevant L. lactis cells to chitin were determined. Then the chitin flakes carrying nisin-producing L. lactis cells were used within the CICON-FER system at different dilution rates (0.1–0.9 h^?1) and initial glucose concentrations (20–60 g l^?1). The results revealed that the pH 7 conditions and the use of 100 mM sodium phosphate buffer with 0.1 % Tween 20 and Triton X-100 significantly increased the binding capacity of ChBD displaying L. lactis cells to chitin. The constructed CICON-FER system maintained the presence of the ChBD surface displaying L. lactis cells in the reactor system until 0.9 h^?1 dilution rate that resulted in a considerably high level of volumetric nisin production and productivity (10,500 IU ml^?1 and 9,450 IU ml^?1 h^?1, respectively) with the combination of a 0.9-h^?1 dilution rate and a 40-g l^?1 initial glucose concentration. In conclusion, an innovative nisin fermentation system that yielded the highest nisin production thus far and that was feasible for industrial application was created.     

Mathematical modelling and process optimization of a continuous 5-stage bioreactor cascade for production of poly[-(R)-3-hydroxybutyrate] by Cupriavidus necator

A multistage system for poly(hydroxyalkanoate) (PHA) production consisting of five continuous stirred tank reactors in series (5-CSTR) with Cupriavidus necator DSM 545 as production strain was modelled using formal kinetic relations. Partially growth-associated production of PHA under nitrogen limited growth was chosen as modelling strategy, thus the Luedeking-Piret’s model of partial growth-associated product synthesis was applied as working hypothesis. Specific growth rate relations adjusted for double substrate (C and N source) limited growth according to Megee et al. and Mankad-Bungay relation were tested. The first stage of the reactor cascade was modelled according to the principle of nutrient balanced continuous biomass production system, the second one as two substrate controlled process, while the three subsequent reactors were adjusted to produce PHB under continuous C source fed and nitrogen deficiency. Simulated results of production obtained by the applied mathematical models and computational optimization indicate that PHB productivity of the whole system could be significantly increased (from experimentally achieved 2.14 g L^?1 h^?1 to simulated 9.95 g L^?1 h^?1) if certain experimental conditions would have been applied (overall dilution rate, C and N source feed concentration). Additionally, supplemental feeding strategy for switching from batch to continuous mode of cultivation was proposed to avoid substrate inhibition.     

The activity of beta-galactosidase and lactose metabolism in Kluyveromyces lactis cultured in cheese whey as a function of growth rate

Aims: Kluyveromyces lactis was cultured in cheese whey permeate on both batch and continuous mode to investigate the effect of time course and growth rate on β‐galactosidase activity, lactose consumption, ethanol production and protein profiles of the cells. Methods and Results: Cheese whey was the substrate to grow K. lactis as a batch or continuous culture. In order to precise the specific growth rate for maximum β‐galactosidase activity a continuous culture was performed at five dilution (growth) rates ranging from 0·06, 0·09, 0·12, 0·18 to 0·24 h^?1. The kinetics of lactose consumption and ethanol production were also evaluated. On both batch and continuous culture a respirofermentative metabolism was detected. The growth stage for maximum β‐gal activity was found to be at the transition between late exponential and entrance of stationary growth phase of batch cultures. Fractionating that transition stage in several growth rates at continuous culture a maximum β‐galactosidase activity at 0·24 h^?1 was observed. Following that stage β‐gal activity undergoes a decline which does not correlate to the density of its corresponding protein band on the gel prepared from the same samples. Conclusion: The maximum β‐galactosidase activity per unit of cell mass was found to be 341·18 mmol ONP min^?1 g^?1 at a dilution rate of 0·24 h^?1. Significance and Impact of the Study: The physiology of K. lactis growing in cheese whey permeate can proven useful to optimize the conversion of that substrate in biomass rich in β‐gal or in ethanol fuel. In addition to increasing the native enzyme the conditions established here can be set to increase yields of recombinant protein production based on the LAC4 promoter in K. lactis host.     

Continuous solvent production by Clostridium beijerinckii BA101 immobilized by adsorption onto brick

The performance of a continuous bioreactor containing Clostridium beijerinckii BA101 adsorbed onto clay brick was examined for the fermentation of acetone, butanol, and ethanol (ABE). Dilution rates from 0.3 to 2.5 h^–1 were investigated with the highest solvent productivity of 15.8 g l^–1 h^–1 being obtained at 2.0 h^–1. The solvent yield at this dilution rate was found to be 0.38 g g^–1 and total solvent concentration was 7.9 g l^–1. The solvent yield was maximum at 0.45 at a dilution rate of 0.3 h^–1. The maximum solvent productivity obtained was found to be 2.5 times greater than most other immobilized continuous and cell recycle systems previously reported for ABE fermentation. A higher dilution rate (above 2.0 h^–1) resulted in acid production rather than solvent production. This reactor was found to be stable for over 550 h. Scanning electron micrographs (SEM) demonstrated that a large amount of C. beijerinckii cells were adsorbed onto the brick support.     

Immobilization of Kluyveromyces marxianus cells containing inulinase activity in open pore gelatin matrix: 2. Application for high fructose syrup production

Batch and continuous production of high fructose syrup from Jerusalem artichoke tubers has been studied using yeast cells immobilized in open pore gelatin matrix. In a batch reactor, the hydrolysis was 93% ($\text{d}\text{-fructose/}\text{d}\text{-glucose}\text{= 90/10}$) and 42 mg d-fructose per ml was produced from the artichoke tuber extract by immobilized cells in 3 h. The same immobilized cells were recycled and used repeatedly for 10 batch cycles starting with fresh juice at the beginning of each cycle. It was found that immobilized cells were extremely stable and the percent hydrolysis was almost constant for all 10 batch cycles. In a continuous reactor using an immobilized cell concentration of 65.7 g (dry wt) l^?1 of total working bioreactor volume, the percent hydrolysis was found to remain constant at ～100% at dilution rates <1.26 h^?1, but beyond that it decreased. Volumetric productivity attained its maximum value at D = 2.08 h^?1 and was found to be 100 g l^?1 h^?1. This was achieved at a feed sugar conversion of 80%. At 90% conversion and D = 1.66 h^?1, the productivity was found to be 90 g l^?1 h^?1. Continuous operation of the immobilized cell bioreactor at a constant dilution rate of 1.65 h^?1 for 240 h resulted in only 2% loss of original activity.     

Hydrogen production by immobilized cells in the nozzle loop bioreactor

Summary The continuous production of hydrogen in a Nozzle Loop Bioreactor was investigated using immobilized Rhodospirillum rubum KS-301 with glucose as the growth-limiting substrate. The maximum hydrogen production rate in the experimental range was 91mL/h at dilution rate 0.4h^-1, initial glucose concentration 5.4g/L, and circulation rate 70h^-1 .     

Alcoholic fermentation by agar-immobilized yeast cells

Immobilized yeast cells in agar gel beads were used in a packed bed reactor for the production of ethanol from cane molasses at 30°C, pH 4.5. The maximum productivity, 79.5g ethanol/l.h was obtained with 195g/l reducing sugar as feed. Substrate (64.2%) was utilized at a dilution of 1.33h^-1. The immobilized cell reactor was operated continuously at a constant dilution rate of 0.67h^-1 for 100 days. The maximum specific ethanol productivity and specific sugar uptake rate were 0.610g ethanol/g cell.h and 1.275g sugar/g cell.h, respectively.     

Kinetics of growth and caffeine demethylase production of Pseudomonas sp. in bioreactor

The effect of various initial caffeine concentrations on growth and caffeine demethylase production by Pseudomonas sp. was studied in bioreactor. At initial concentration of 6.5 g l^?1 caffeine, Pseudomonas sp. showed a maximum specific growth rate of 0.2 h^?1, maximum degradation rate of 1.1 g h^?1, and caffeine demethylase activity of 18,762 U g CDW^?1 (CDW: cell dry weight). Caffeine degradation rate was 25 times higher in bioreactor than in shake flask. For the first time, we show highest degradation of 75 g caffeine (initial concentration 20 g l^?1) in 120 h, suggesting that the tested strain has potential for successful bioprocess for caffeine degradation. Growth kinetics showed substrate inhibition phenomenon. Various substrate inhibition models were fitted to the kinetic data, amongst which the double-exponential (R ² = 0.94), Luong (R ² = 0.92), and Yano and Koga 2 (R ² = 0.94) models were found to be the best. The Luedeking–Piret model showed that caffeine demethylase production kinetics was growth related. This is the first report on production of high levels of caffeine demethylase in batch bioreactor with faster degradation rate and high tolerance to caffeine, hence clearly suggesting that Pseudomonas sp. used in this study is a potential biocatalyst for industrial decaffeination.     

Enhanced ethanol production by continuous fermentation in a two-tank system with cell recycling

An experimental method for producing ethanol continuously was designed and tested with a cell-recycling two-tank system, which was composed of two fermentors, each of which was individually equipped with a settler for recycling flocculent yeast. This system was effective for the continuous fermentation of ethanol from sucrose at high cell-recycling (r = 0.8–0.9) and dilution (up to 0.48 h^?1) rates. The system has several advantages; the high cell concentration in the fermentors and relief of substrate and product inhibition. Thus, the enhanced productivity using this continuous fermentation with the two-tank cell-recycling system was significantly higher compared with that of the batch fermentation. The results indicate that increased recycling ratios caused an increase in biomass concentration and subsequently, product concentration in the tank. The ethanol productivity increased with the dilution rate, but higher dilution rates could render increasing amounts of sugar unconverted. Continuous fermentation with the sugar feed concentration of 160 g/l at r = 0.9 and dilution rate of 0.2 h^?1 achieved the highest productivity with less than 2% of the unconverted sugar in the product steam. Under the same cell recycling ratios a productivity range of 6.9–7.5 g/l h^?1 could be achieved with feeding concentrations of 80–200 g/l, while batch fermentation at these sugar concentrations led to productivities of 3.85–4.48 g/l h^?1.     

Evaluation of ethanol production by a new isolate of yeast during fermentation in synthetic medium and sugarcane bagasse hemicellulosic hydrolysate

A new xylose fermenting yeast was isolated from over-ripe banana by enrichment in xylose-containing medium. The phylogenetic analysis of ITS1-5.8S-ITS2 region sequences of ribosomal RNA of isolate BY2 revealed that it shows affiliation to genus Pichia and clades with Pichia caribbica. In batch fermentation, Pichia strain BY2 fermented xylose, producing 15 g l^?1 ethanol from 30 g l^?1 xylose under shaking conditions at 28°C, with ethanol yield of 0.5 g g^?1 and volumetric productivity of 0.31 g l^?1 h^?1. The optimum pH range for ethanol production from xylose by Pichia strain BY2 was 5–7. Pichia strain BY2 also produced 6.08 g l^?1 ethanol from 30 g l^?1 arabinose. Pichia strain BY2 can utilize sugarcane bagasse hemicellulose acid hydrolysate for alcohol production, efficiency of fermentation was improved by neutralization, and sequential use of activated charcoal adsorption method. Percent total sugar utilized and ethanol yield for the untreated hydrolysate was 17.14% w/v and 0.33 g g^?1, respectively, compared with 66.79% w/v and 0.45 g g^?1, respectively, for treated hemicellulose acid hydrolysate. This new yeast isolate showed ethanol yield of 0.45 g g^?1 and volumetric productivity of 0.33 g l^?1 h^?1 from sugarcane bagasse hemicellulose hydrolysate detoxified by neutralization and activated charcoal treatment, and has potential application in practical process of ethanol production from lignocellulosic hydrolysate.     

Continuous production of high-purity fructooligosaccharides and ethanol by immobilized Aspergillus japonicus and Pichia heimii

High-purity fructooligosaccharides (FOS) were produced from sucrose by an innovative process incorporating immobilized Aspergillus japonicus and Pichia heimii cells. Intracellular FTase of A. japonicus converted sucrose into FOS and glucose, and P. heimii fermented glucose mainly into ethanol. The continuous production of FOS was carried out using a tanks-in-series bioreactor consisting of three stirred tanks. When a solution composed of 1 g L^?1 yeast extract and 300 g L^?1 sucrose was fed continuously to the bioreactor at a dilution rate of 0.1 h^?1, FOS at a purity of up to 98.2 % could be achieved and the value-added byproduct ethanol at 79.6 g L^?1 was also obtained. One gram of sucrose yielded 0.62 g FOS and 0.27 g ethanol. This immobilized dual-cell system was effective for continuous production of high-purity FOS and ethanol for as long as 10 days.     

Carotenoid production from hydrolyzed molasses by Dietzia natronolimnaea HS-1 using batch,fed-batch and continuous culture

The different cultivation strategies of batch, fed-batch and continuous culture for the synthesis of biomass and carotenoids by Dietzia natronolimnaea HS-1 from waste molasses and its hydrolysate were compared. The efficiency of three various pretreatments (enzymatic, acidic and acidic at high temperature) for the determination of the best hydrolysate was also studied by evaluating the conversion rate of sucrose. The analytical procedures initially showed that canthaxanthin (CTX) and enzymatic hydrolysis were the most abundant pigment biosynthesized and the most suitable process for the substrate production, respectively. An increase in reducing sugar concentration of the enzymatic hydrolysate molasses (EHM) from 25 to 50 g/l led to a drastic decrease in biomass formation and substrate utilization. EHM (25 g/l) was a better substrate for the cell growth and product formation than the waste molasses (25 g/l). The application of EHM instead of molasses enhanced the biomass production in fed-batch culture more than batch and continuous cultures. However, the continuous cultivation had the highest biomass (12.98 g/l), carotenoid (27.33 mg/l) and CTX (25.04 mg/l) yields with 25 g/l of EHM. The CTX isolated from D. natronolimnaea HS-1 may be used as a natural antioxidant for possible production of healthy-functional foods in the future.     

Continuous acetone–butanol–ethanol production by corn stalk immobilized cells

Corn stalk was used as a support to immobilize Clostridia beijerinckii ATCC 55025 in the fermentation process of acetone, butanol, and ethanol production. The effect of the dilution rate on solvent production was examined in a steady-state 20-day continuous flow operation. The maximum total solvent concentration of 8.99 g l⁻¹ was obtained at a dilution rate of 0.2 h⁻¹. Increasing the dilution rate between 0.2 and 1.0 h⁻¹ resulted in an increased solvent productivity, and the highest solvent productivity was obtained at 5.06 g l⁻¹ h⁻¹ with a dilution rate of 1 h⁻¹. The maximum solvent yield from glucose of 0.32 g g⁻¹ was observed at 0.25 h⁻¹. The cell adsorption and morphology change during the growth on corn stalk support were examined by the SEM.