Cultivation of plant cells in a stirred vessel: effect of impeller design

Suspension cultures of Nicotiana tabacum were grown in a batch fermentor using different agitation systems. The effects of the impeller type, size, and agitation speed on the productivity of cell mass and secondary metabolites (phenolics) have been investigated. The use of a large, flat-bladed impeller (diameter 7.6 cm; width 14.0 cm) improved culture growth significantly over systems using a regular, flat-bladed impeller (diameter 5.6 cm; width 1.5 cm). An impeller of the same dimensions as the 14.0-cm-wide, large, flat-bladed impeller with sail cloth blades yielded a higher maximum growth rate in the exponential phase but resulted in a longer lag phase. Overall (intracellular and extracellular) phenolics concentration showed a direct relationship to culture growth rate whereas extracellular concentrations were a function of agitation conditions. Power consumption and flow pattern studies were also completed to further characterize the different impellers tested.     

CFD simulation of mixing for high-solids anaerobic digestion

A computational fluid dynamics (CFD) model that simulates mechanical mixing for high-solids anaerobic digestion was developed. Numerical simulations of mixing manure slurry which exhibits non-Newtonian pseudo-plastic fluid behavior were performed for six designs: (i) one helical ribbon impeller; (ii) one anchor impeller; (iii) one curtain-type impeller; (iv) three counterflow (CF-2) impellers; (v) two modified high solidity (MHS 3/39°) impellers; and (vi) two pitched blade turbine impellers. The CFD model was validated against measurements for mixing a Herschel-Bulkley fluid by ribbon and anchor impellers. Based on mixing time with respect to mixing energy level, three impeller types (ribbon, CF-2, and MHS 3/39°) stand out when agitating highly viscous fluids, of these mixing with two MHS 3/39° impellers requires the lowest power input to homogenize the manure slurry. A comparison of digestion material demonstrates that the mixing energy varies with manure type and total solids concentration to obtain a given mixing time. Moreover, an in-depth discussion about the CFD strategy, the influences of flow regime and impeller type on mixing characteristics, and the intrinsic relation between mixing and flow field is included.     

Optimization of agitation and aeration conditions for maximum virginiamycin production

To maximize the productivity of virginiamycin, which is a commercially important antibiotic as an animal feed additive, an empirical approach was employed in the batch culture of Streptomyces virginiae. Here, the effects of dissolved oxygen (DO) concentration and agitation speed on the maximum cell concentration at the production phase, as well as on the productivity of virginiamycin, were investigated. To maintain the DO concentration in the fermentor at a certain level, either the agitation speed or the inlet oxygen concentration of the supply gas was manipulated. It was found that increasing the agitation speed had a positive effect on the antibiotic productivity independent of the DO concentration. The optimum DO concentration, agitation speed and addition of an autoregulator, virginiae butanolide C (VB-C), were determined to maximize virginiamycin productivity. The optimal strategy was to start the cultivation at 450 rpm and to continue until the DO concentration reached 80%. After reaching 80%, the DO concentration was maintained at this level by changing the agitation speed, up to a maximum of 800 rpm. The addition of an optimal amount of the autoregulator VB-C in an experiment resulted in the maximal production of virginiamycin M (399 mg/l), which was about 1.8-fold those obtained previously. Received: 13 July 1998 / Received revision: 19 August 1998 / Accepted: 13 September 1998     

A comprehensive comparison of mixing, mass transfer, Chinese hamster ovary cell growth, and antibody production using Rushton turbine and marine impellers

Large scale production of monoclonal antibodies has been accomplished using bioreactors with different length to diameter ratios, and diverse impeller and sparger designs. The differences in these physical attributes often result in dissimilar mass transfer, mechanical stresses due to turbulence and mixing inside the bioreactor that may lead to disparities in cell growth and antibody production. A rational analysis of impeller design parameters on cell growth, protein expression levels and subsequent antibody production is needed to understand such differences. The purpose of this study was to examine the impact of Rushton turbine and marine impeller designs on Chinese hamster ovary (CHO) cell growth and metabolism, and antibody production and quality. Experiments to evaluate mass transfer and mixing characteristics were conducted to determine if the nutrient requirements of the culture would be met. The analysis of mixing times indicated significant differences between marine and Rushton turbine impellers at the same power input per unit volume of liquid (P/V). However, no significant differences were observed between the two impellers at constant P/V with respect to oxygen and carbon dioxide mass transfer properties. Experiments were conducted with CHO cells to determine the impact of different flow patterns arising from the use of different impellers on cell growth, metabolism and antibody production. The analysis of cell culture data did not indicate any significant differences in any of the measured or calculated variables between marine and Rushton turbine impellers. More importantly, this study was able to demonstrate that the quality of the antibody was not altered with a change in the impeller geometry.     

Comparison of neomycin production from Streptomyces fradiae cultivation using soybean oil as the sole carbon source in an air-lift bioreactor and a stirred-tank reactor

Streptomyces fradiae was cultivated in both an air-lift bioreactor and a jar-fermentor with various agitation rates from 200 to 800 rpm to investigate differences in neomycin production between the two reactors. Final neomycin concentrations in the jar-fermentor operated at 600 rpm and the air-lift bioreactor were 3.19 and 1.39 g/l, respectively. On the other hand, levels of soybean oil consumption in the two reactors were 25.9 and 9.4 g/l, respectively. Shear stress due to mechanical agitation caused changes in the morphology of mycelia and influenced neomycin production. The morphological changes of the mycelia in the jar-fermentor caused the viscosity of the culture broth to decrease by half, and soybean oil consumption and fatty acid uptake rate to increase 3- and 1.8-fold, respectively, in comparison with those of the air-lift bioreactor. The product yield coefficient determined from the level of soybean oil consumption in the air-lift bioreactor was similar to that of the jar-fermentor at 600 rpm, but the neomycin yield was less than one-half. In the case of the jar-fermentor, the yield increased with increasing agitation rate and was maximum at 600 rpm. To maximize neomycin production in S. fradiae cultures using soybean oil as sole carbon source, it was necessary to provide a degree of shear stress to the mycelia and to optimize liquid mixing. In an air-lift bioreactor, the soybean oil consumption may be suppressed due to a low degree of liquid mixing.     

A novel centrifugal impeller bioreactor. II. Oxygen transfer and power consumption

The effects of the impeller configuration, aeration rate, and agitation speed on oxygen transfer coefficient K(L)a were studied in a newly designed centrifugal impeller bioreactor (5-L). The oxygen transfer rates in the novel bioreactor were also compared with those in a cell-lift bioreactor with comparable dimensions. The cell-lift impeller produced much higher surface oxygen transfer rates than the centrifugal one at an agitation speed over 200 rpm. This result was in good agreement with our observation that the cell-lift impeller produced much higher unfavorable turbulence. In addition, the experiments using granulated agar particles as pseudo plant cells indicated that the K(L)a value decreased steadily with an increase in agar particle concentration, and the centrifugal impeller still demonstrated a larger K(L)a than the cell lift up to a high pseudo cell concentration of 19.5 g dry weight (DW)/L (under 150 rpm and 0.20 vvm) or 22.3 g DW/L (under 200 rpm and 0.20 vvm). Furthermore, the correlation between power number and impeller Reynolds number for both the centrifugal and the cell-lift impellers was successfully obtained, which could be used for predicting the power input required by each impeller. From the results obtained, the centrifugal impeller bioreactor is expected to have great potential in its application to shear-sensitive biological systems.     

溶氧对Candida glycerinogenes产甘油发酵过程的影响

研究了溶氧浓度对产甘油假丝酵母分批发酵生产甘油过程的影响。实验结果表明：当溶氧浓度控制在30%时,C. glycerinogenes的甘油产量、得率和产率达到最高,分别为120.7 g/L、0.575 g/g和1.69 g/(L•h),而糖酵解代谢副产物形成最少。当溶氧浓度为10%时,发酵过程呈现出“巴斯德效应”的特征,生成的酵解代谢副产物维持在较高水平。在快速生长阶段,随着溶氧从10%增加到60%,细胞呼吸类型表现为从厌氧呼吸向好氧呼吸转变,酵解代谢副产物依次减少。在生长稳定期,控制的溶氧浓度越高,酵解代谢副产物乙醇、乙酸等的生成减少。分别选用Logistic方程、Luedeking-Piret方程和Luedeking-Piret-like方程,能较好地模拟细胞生长、甘油合成和葡萄糖消耗的动力学过程。     

操作条件对5′-单磷酸胞苷晶体粒度分布的影响

为了研究操作条件对5。单磷酸胞苷（5′-CMP）晶体粒度分布的影响,分别采用不同形式的搅拌桨、搅拌速率以及反应液流加速率,并且运用激光粒度仪和扫描电镜对晶体粒度分布及形貌进行分析观测。结果显示：采用不同形式的搅拌桨形成的剪切力、颗粒聚集以及二次成核现象的差异导致了晶体粒度分布峰值数量不同;分别选取50、100和150r／min的搅拌速率以及1、3和6mL／h的流加速率时,晶体平均粒径在铆式搅拌桨作用下,在120．3—212．1μm范围内递减,而在45°斜角四折叶式搅拌桨作用下递减范围为3．17～150．2μm,且粒度分布更为均匀,为工业生产中的优化控制提供了一定的理论依据。     

Triarylmethane Dye Decolorization by Pellets of Pycnoporus sanguineus: Statistical Optimization and Effects of Novel Impeller Geometry

A study was carried out to optimize selected parameters for decolorization of a triarylmethane dye, such as crystal violet by white rot fungus, Pycnoporus sanguineus, pellets. The parameters studied were initial dye concentration (ppm), agitation speed (rpm), and process time (days) and were optimized using response surface methodology (RSM). It is shown that process time, agitation speed, and their interactions have significant effects on the decolorization process. Following the optimization, the decolorization study was extended to a stirred tank reactor (STR) process. Effects of different geometry of impellers on the decolorization process and power consumption were studied. Novel impeller geometries, such as 180° curved blade and 60° angled blade impellers, were used in the STR. The application of 180° curved blade impeller resulted in higher percentage of decolorization at a relatively less power consumption as compared with 60° angled blade impeller.     

Scale-up synthesis of lipase-catalyzed palm esters in stirred-tank reactor

Lipase-catalyzed production of palm esters by alcoholysis of palm oil with oleyl alcohol in n-hexane was performed in 2L stirred-tank reactor (STR). Investigation on the performance of reactor operation was carried out in batch mode STR with single impeller mounted on the centrally located shaft. Rushton turbine (RT) impellers provide the highest reaction yield (95.8%) at lower agitation speed as compared to AL-hydrofoil (AL-H) and 2-bladed elephant ear (EE) impellers. Homogenous enzyme particles suspension was obtained at 250 rpm by using RT impeller. At higher impeller speed, the shear effect on the enzyme particles caused by agitation has decreased the reaction performance. Palm esters reaction mixture in STR follows Newtons' law due to the linear relation between the shear stress (tau) and shear rate (dupsilon/dy). High stability of Lipozyme RM IM was observed as shown by its ability to be repeatedly used to give high percentage yield (79%) of palm esters even after 15 cycles of reaction. The process was successfully scale-up to 75 L STR (50 L working volume) based on a constant impeller tip speed approach, which gave the yield of 97.2% after 5h reaction time.     

High density cultivation of Anchusa officinalis in a stirred-tank bioreactor with in situ filtration

Previously, Su et al. [Biotechnol Bioeng 42: 884–890 (1993)] reported improved production of rosmarinic acid by Anchusa officinalis in shake-flask cultures using a cultivation strategy that involved intermittent medium exchange. Implementation of this cultivation strategy in 2.5-1 stirred-tank bioreactor cultures is investigated in the present study. Intermittent cell/medium separation in the bioreactor was accomplished by means of automated in situ culture filtration. In the bioreactor culture, rosmarinic acid production was found very sensitive to agitation and aeration conditions as well as dissolved oxygen concentration. A maximum cell density of 35 g dry weight/l and a rosmarinic acid concentration of 3.7 g/l were obtained by maintaining the dissolved oxygen concentration above 30% air saturation, gradually raising the impeller tip speed from 34 cm/s to 72 cm/s, and keeping the aeration rate at 0.44 vvm while increasing the O₂: air ratio in the gas feed stream to 4:1. This result is comparable with the data obtained from shake-flask cultures using the same culture strategy.     

Performance of mammalian cell culture bioreactor with a new impeller design

To improve the oxygen transfer in a mammalian cell bioreactor, a new type of impeller consisting of a double-screen concentric cylindrical cage impeller (annular cage impeller in short) was designed and its mass transfer rate evaluated. This new impeller design increases the specific screen area, and the convective mass transfer rate through the annular cage was significantly increased. The oxygen transfer rates with the new impeller and the commercially available cell-lift impeller (CelliGen by New Brunswick Scientific Co.) were evaluated and their performance compared at various rates of aeration and agitation. The results showed that with the new impeller, the oxygen transfer rate was increased by 19% in water and 21% in cell-free culture medium supplemented with 10% horse serum, the total hybridoma cell concentration was increased to 3.4 x 10(7) cells/mL, and the IgG(1) subtype monoclonal antibody (MAb) product concentration was also increased to 512 mg/L in perfusion culture of murine hybridoma cell line 62'D3. These improvements in oxygen transfer rate, cell concentration, and MAb product concentration are all very significant. The mass transfer resistance in the cell-lift impeller system was found to be mainly due to the surface area of the single-screen cage impeller. The new annular cage impeller not only provided the increased surface area for convective oxygen transfer but also protected cells from hydrodynamic shear damage, thereby achieving a significant bioprocess improvement in terms of higher viable cell concentration, higher product concentration, and higher oxygen transfer rate in the mammalian cell bioreactor system.     

Influence of impeller speed on citric acid production and selected enzyme activities of the TCA cycle

Summary The effect of impeller speed on citric acid production and selected enzyme activities of the TCA cycle was studied. The highest yield of citric acid (28 g/l) was obtained in culture agitated at lower speed (300 rpm). The activity of citrate synthase decreased with the increase of speed of agitation, while the activity of aconitase and isocitrate dehydrogenase increased with the increase in agitation speed.     

Azadirachtin production in stirred tank reactors by Azadirachta indica suspension culture

Successful scale-up of Azadirachta indica suspension culture for azadirachtin production was done in stirred tank bioreactor with two different impellers. The kinetics of biomass accumulation, nutrient consumption and azadirachtin production of A. indica cell suspension culture were studied in a stirred tank bioreactor equipped with centrifugal impeller and compared with similar bioreactor with a setric impeller to investigate the role of O₂ transfer efficiency of centrifugal impeller bioreactor on overall culture metabolism. The maximum cell mass for centrifugal impeller bioreactor and stirred tank bioreactor (with setric impeller) were 18.7 and 15.5 g/L (by dry cell weight) and corresponding azadirachtin concentrations were 0.071 and 0.05 g/L, respectively. Glucose and phosphate were identified as the major growth-limiting nutrients during the bioreactor cultivation. The centrifugal impeller bioreactor demonstrated less shearing and improved O₂ transfer than the stirred tank bioreactor equipped with setric impeller with respect to biomass and azadirachtin production.     

Dependence of penicillium chrysogenum growth, morphology, vacuolation, and productivity in fed-batch fermentations on impeller type and agitation intensity

The influence of the agitation conditions on the growth, morphology, vacuolation, and productivity of Penicillium chrysogenum has been examined in 6 L fed-batch fermentations. A standard Rushton turbine, a four-bladed paddle, and a six-bladed pitched blade impeller were compared. Power inputs per unit volume of liquid, P/VL, ranged from 0.35 to 7.4 kW/m3. The same fermentation protocol was used in each fermentation, including holding the dissolved oxygen concentration above 40% air saturation by gas blending. The mean projected area (for all dispersed types, including clumps) and the clump roughness were used to characterize the morphology. Consideration of clumps was vital as these were the predominant morphological form. For a given impeller, the batch-phase specific growth rates and the overall biomass concentrations increased with agitation intensity. Higher fragmentation at higher speeds was assumed to have promoted growth through increased formation of new growing tips. The mean projected area increased during the rapid growth phase followed by a sharp decrease to a relatively constant value dependent on the agitation conditions. The higher the speed, the lower the projected area for a given impeller type. The proportion by volume of hyphal vacuoles and empty regions decreased with speed, possibly due to fragmentation in the vacuolated regions. The specific penicillin production rate was generally higher with lower impeller speed for a given impeller type. The highest value of penicillin production as well as its rate was obtained using the Rushton turbine impeller at the lowest speed. At given P/VL, changes in morphology, specific growth rate, and specific penicillin production rate depended on impeller geometry. The morphological data could be correlated with either tip speed or the "energy dissipation/circulation function," but a reasonable correlation of the specific growth rate and specific production rate was only possible with the latter. Copyright 1998 John Wiley & Sons, Inc.     

Effect of oxygen transfer on lipase production by Acinetobacter radioresistens

The influence of oxygen on alkaline lipase production by Acinetobacter radioresistens was studied under two operating modes: controlled dissolved oxygen (DO) concentration and controlled aeration rate. Compared with cell growth, the lipase production depended more extensively on oxygen. The intrinsic factor determining cell growth and lipase production was oxygen transfer rate (OTR) rather than DO concentration. Improvements in OTR, either by aeration or agitation, resulted in an increase in lipase yield and/or a reduction in fermentation time. The formation of A. radioresistens lipase could be described by a mixed-growth-associated model, and the enzyme was mainly a growth-associated product. The overall productivity for the lipase, which depended more strongly on agitation than aeration, could be related with kLa. DO concentration could not be employed in this correlation, though it has been useful as a criterion for ensuring no oxygen limitation in an aerobic fermentation.     

Improved bacterial nanocellulose production from glucose without the loss of quality by evaluating thirteen agitator configurations at low speed

Thirteen agitator configurations were investigated at low speed in stirred-tank reactors (STRs) to determine if improved crude bacterial nanocellulose (BNC) productivity can be achieved from glucose-based media while maintaining high BNC quality using Komagataeibacter xylinus ATCC 23770 as a model organism. A comparison of five single impellers showed the pitched blade (large) was the optimal impeller at 300 rpm. The BNC production was further increased by maintaining the pH at 5.0. Among the single helical ribbon and frame impellers and the combined impellers, the twin pitched blade provided the best results. The combined impellers at 150 rpm performed better than the single impellers, and after optimizing the agitation conditions, the twin pitched blade (large) and helical ribbon impellers performed the best at 100 rpm. The performances of different agitators at low speed during BNC production were related to how efficiently the agitators improved the oxygen mass transfer coefficient. The twin pitched blade (large) was verified as providing the optimum performance by an observed crude BNC production of 1.97 g (L×d)⁻¹ and a BNC crude yield of consumed glucose of 0.41 g g⁻¹, which were 2.25 and 2.37 times higher than the initial values observed using the single impeller respectively. Further characterization indicated that the BNC obtained at 100 rpm from the STR equipped with the optimal agitator maintained high degree of polymerization and crystallinity.     

Influence of bioreactor design on the rate and amount of curdlan-type exopolysaccharide production byAlcaligenes faecalis

Summary The amount of polymer recovered during lab-scale batch production of curdlan-type polysaccharide byAlcaligenes faecalis (ATCC 31749) was increased by 46% through the manipulation of the vessel configuration. When standard turbine impellers were used to provide mixing and agitation the specific rate of production, Qp, decreased significantly after 40–50 hours elapsed fermentation time, EFT. The Qp remained at a high level throughout the entire time course of production (90 hours) when (i) a propeller was substituted for a flat-blade turbine impeller in a conventional baffled stirred tank reactor, or (ii) agitation and mixing were accomplished in a non-rotary vibro-fermenter.     

An oxygen supply strategy for the large-scale production of tissue plasminogen activator by microcarrier cell culture

An oxygen supply strategy involving agitation speed and aeration method for the large-scale production of tissue plasminogen activator (TPA) by a microcarrier cell culture was investigated by small-scale model experiments. A preliminary calculation indicated that diffusion limitation of dissolved oxygen (DO) could be caused in a microcarrier sedimentation layer more than 0.5 mm in thickness. Within an agitation speed range above 70 rpm, which was the critical speed for all of the microcarrier beads to remain suspended and thus for avoiding a deficiency of DO, the TPA productivity was higher at a lower agitation speed, while the cell concentration was not affected by the agitation speed. The addition of soluble starch to the culture medium prevented sedimentation of the microcarrier beads, even at the low agitation speed of 20 rpm, resulting in a TPA productivity higher than that at 70 rpm, which was the optimum speed without soluble starch. Use of an air spray system with an optimized air flow rate resulted in a k_La 2.35 times higher than that with simple surface aeration. Increasing the internal pressure of the culture from 0.2 kg/cm² (1209 hPa) to 1.5 kg/cm² (2483 hPa) had no effect on the cell growth but slightly increased the TPA production rates. However, based on the glucose consumption, both the cell and TPA yields were much improved by pressurization. As an optimum mixing and oxygen supply strategy for the production of TPA on a large scale, it is recommended that soluble starch be added to the culture medium to allow the microcarrier suspension to be maintained at a low agitation speed, while keeping a high oxygen transfer rate by means of an air spray system and pressurization.