A Lithium–Sulfur Cell Based on Reversible Lithium Deposition from a Li2S Cathode Host onto a Hostless‐Anode Substrate

The development of lithium–sulfur batteries necessitates a thorough understanding of the lithium‐deposition process. A novel full‐cell configuration comprising an Li₂S cathode and a bare copper foil on the anode side is presented here. The absence of excess lithium allows for the realization of a truly lithium‐limited Li–S battery, which operates by reversible plating and stripping of lithium on the hostless‐anode substrate (copper foil). Its performance is closely tied to the efficiency of lithium deposition, generating valuable insights on the role and dynamic behavior of lithium anode. The Li₂S full cell shows reasonable capacity retention with a Coulombic efficiency of 96% over 100 cycles, which is a tremendous improvement over that of a similar lithium‐plating‐based full cell with LiFePO₄ cathodes. The exceptional robustness of the Li₂S system is attributed to an intrinsic stabilization of the lithium‐deposition process, which is mediated by polysulfide intermediates that form protective Li₂S and Li₂S₂ regions on the deposited lithium. Combined with the large improvements in energy density and safety by the elimination of a metallic lithium anode, the stability and electrochemical performance of the lithium‐plating‐based Li₂S full cell establish it as an important trajectory for Li–S battery research, focusing on practical realization of reversible lithium anodes.     

Tailored Reaction Route by Micropore Confinement for Li–S Batteries Operating under Lean Electrolyte Conditions

Lithium‐sulfur (Li–S) batteries are one of the most promising alternative energy storage systems beyond Li‐ion batteries. However, the sluggish kinetics of the nucleation and growth of the solid discharge product of Li₂S/Li₂S₂ in the lower discharge plateau has been recently identified as a critical hurdle for attaining high specific capacity in Li–S batteries with high sulfur loadings under lean electrolyte conditions. Herein, a new strategy of breaking the charge‐transport bottleneck by successful generation of experimentally verified stable Li₂S₂ and a reservoir of quasi‐solid lithium polysulfides within the micropores of activated carbon fiber cloth as a high‐sulfur‐loading host is proposed. The developed Li–S cell is capable of delivering a highly sustainable areal capacity of 6.0 mAh cm^?2 under lower electrolyte to sulfur ratios (<3.0 mL_E g_S^?1). Micropore confinement leads to generation of solid Li₂S₂ that enables high utilization of the entire electroactive area by its inherent self‐healing capacity. This strategy opens a new avenue for rational material designs for Li–S batteries under lean electrolyte condition.     

Unraveling the Dual Functionality of High‐Donor‐Number Anion in Lean‐Electrolyte Lithium‐Sulfur Batteries

Minimizing electrolyte use is essential to achieve high practical energy density of lithium–sulfur (Li–S) batteries. However, the sulfur cathode is more readily passivated under a lean electrolyte condition, resulting in low sulfur utilization. In addition, continuous electrolyte decomposition on the Li metal anode aggravates the problem, provoking rapid capacity decay. In this work, the dual functionalities of NO₃^? as a high‐donor‐number (DN) salt anion is presented, which improves the sulfur utilization and cycling stability of lean‐electrolyte Li–S batteries. The NO₃^? anion elevates the solubility of the sulfur species based on its high electron donating ability, achieving a high sulfur utilization of above 1200 mA h g^?1. Furthermore, the anion suppresses electrolyte decomposition on the Li metal by regulating the lithium ion (Li⁺) solvation sheath, enhancing the cycle performance of the lean electrolyte cell. By understanding the anionic effects, this work demonstrates the potential of the high‐DN electrolyte, which is beneficial for both the cathode and anode of Li–S batteries.     

Metal Sulfide‐Decorated Carbon Sponge as a Highly Efficient Electrocatalyst and Absorbant for Polysulfide in High‐Loading Li2S Batteries

Owing to its high theoretical specific capacity (1166 mA h g^?1) and particularly its advantage to be paired with a lithium‐metal‐free anode, lithium sulfide (Li₂S) is regarded as a much safer cathode for next‐generation advanced lithium–sulfur (Li–S) batteries. However, the low conductivity of Li₂S and particularly the severe “polysulfide shuttle” of lithium polysulfide (LiPS) dramatically hinder their practical application in Li–S batteries. To address such issues, herein a bifuctional 3D metal sulfide‐decorated carbon sponge (3DTSC), which is constructed by 1D carbon nanowires cross‐linked with 2D graphene nanosheets with high conductivity and polar 0D metal sulfide nanodots with efficient electrocatalytic activity and strong chemical adsorption capability for LiPSs, is presented. Benefiting from the well‐designed multiscale, multidimensional 3D porous nanoarchitecture with high conductivity, and efficient electrocatalytic and absorption ability, the 3DTSC significantly mitigates LiPS shuttle, improves the utilization of Li₂S, and facilitates the transport of electrons and ions. As a result, even with a high Li₂S loading of 8 mg cm^?2, the freestanding 3DTSC‐Li₂S cathode without a polymer binder and metallic current collector delivers outstanding electrochemical performance with a high areal capacity of 8.44 mA h cm^?2.     

High‐Performance Lithium‐Sulfur Batteries with a Self‐Supported, 3D Li2S‐Doped Graphene Aerogel Cathodes

Lithium‐sulfur (Li‐S) batteries are being considered as the next‐generation high‐energy‐storage system due to their high theoretical energy density. However, the use of a lithium‐metal anode poses serious safety concerns due to lithium dendrite formation, which causes short‐circuiting, and possible explosions of the cell. One feasible way to address this issue is to pair a fully lithiated lithium sulfide (Li₂S) cathode with lithium metal‐free anodes. However, bulk Li₂S particles face the challenges of having a large activation barrier during the initial charge, low active‐material utilization, poor electrical conductivity, and fast capacity fade, preventing their practical utility. Here, the development of a self‐supported, high capacity, long‐life cathode material is presented for Li‐S batteries by coating Li₂S onto doped graphene aerogels via a simple liquid infiltration–evaporation coating method. The resultant cathodes are able to lower the initial charge voltage barrier and attain a high specific capacity, good rate capability, and excellent cycling stability. The improved performance can be attributed to the (i) cross‐linked, porous graphene network enabling fast electron/ion transfer, (ii) coated Li₂S on graphene with high utilization and a reduced energy barrier, and (iii) doped heteroatoms with a strong binding affinity toward Li₂S/lithium polysulfides with reduced polysulfide dissolution based on first‐principles calculations.     

Highly Dispersed Cobalt Clusters in Nitrogen‐Doped Porous Carbon Enable Multiple Effects for High‐Performance Li–S Battery

The lithium–sulfur (Li–S) battery is considered a promising candidate for the next generation of energy storage system due to its high specific energy density and low cost of raw materials. However, the practical application of Li–S batteries is severely limited by several weaknesses such as the shuttle effect of polysulfides and the insulation of the electrochemical products of sulfur and Li₂S/Li₂S₂. Here, by doping nitrogen and integrating highly dispersed cobalt catalysts, a porous carbon nanocage derived from glucose adsorbed metal–organic framework is developed as the host for a sulfur cathode. This host structure combines the reported positive effects, including high conductivity, high sulfur loading, effective stress release, fast lithium‐ion kinetics, fast interface charge transport, fast redox of Li₂S_n, and strong physical/chemical absorption, achieving a long cycle life (86% of capacity retention at 1C within 500 cycles) and high rate performance (600 mAh g^?1 at 5C) for a Li–S battery. By combining experiments and density functional theoretical calculations, it is demonstrated that the well‐dispersed cobalt clusters play an important role in greatly improving the diffusion dynamics of lithium, and enhance the absorption and conversion capability of polysulfides in the host structure.     

Conductive and Catalytic Triple‐Phase Interfaces Enabling Uniform Nucleation in High‐Rate Lithium–Sulfur Batteries

Rechargeable lithium–sulfur batteries have attracted tremendous scientific attention owing to their superior energy density. However, the sulfur electrochemistry involves multielectron redox reactions and complicated phase transformations, while the final morphology of solid‐phase Li₂S precipitates largely dominate the battery's performance. Herein, a triple‐phase interface among electrolyte/CoSe₂/G is proposed to afford strong chemisorption, high electrical conductivity, and superb electrocatalysis of polysulfide redox reactions in a working lithium–sulfur battery. The triple‐phase interface effectively enhances the kinetic behaviors of soluble lithium polysulfides and regulates the uniform nucleation and controllable growth of solid Li₂S precipitates at large current density. Therefore, the cell with the CoSe₂/G functional separator delivers an ultrahigh rate cycle at 6.0 C with an initial capacity of 916 mAh g^?1 and a capacity retention of 459 mAh g^?1 after 500 cycles, and a stable operation of high sulfur loading electrode (2.69–4.35 mg cm^?2). This work opens up a new insight into the energy chemistry at interfaces to rationally regulate the electrochemical redox reactions, and also inspires the exploration of related energy storage and conversion systems based on multielectron redox reactions.     

A Li2S‐TiS2‐Electrolyte Composite for Stable Li2S‐Based Lithium–Sulfur Batteries

Li₂S is a fully lithiated sulfur‐based cathode with a high theoretical capacity of 1166 mAh g^?1 that can be coupled with lithium‐free anodes to develop high‐energy‐density lithium–sulfur batteries. Although various approaches have been pursued to obtain a high‐performance Li₂S cathode, there are still formidable challenges with it (e.g., low conductivity, high overpotential, and irreversible polysulfide diffusion) and associated fabrication processes (e.g., insufficient Li₂S, excess electrolyte, and low reversible capacity), which have prevented the realization of high electrochemical utilization and stability. Here, a new cathode design composed of a homogeneous Li₂S‐TiS₂‐electrolyte composite that is prepared by a simple two‐step dry/wet‐mixing process is demonstrated, allowing the liquid electrolyte to wet the powder mixture consisting of insulating Li₂S and conductive TiS₂. The close‐contact, three‐phase boundary of this system improves the Li₂S‐activation efficiency and provides fast redox‐reaction kinetics, enabling the Li₂S‐TiS₂‐electrolyte cathode to attain stable cyclability at C/7 to C/3 rates, superior long‐term cyclability over 500 cycles, and promising high‐rate performance up to 1C rate. More importantly, this improved performance results from a cell design attaining a high Li₂S loading of 6 mg cm^?2, a high Li₂S content of 75 wt%, and a low electrolyte/Li₂S ratio of 6.     

Freestanding Flexible Li2S Paper Electrode with High Mass and Capacity Loading for High‐Energy Li–S Batteries

Lithium–sulfur (Li–S) batteries are a very appealing power source with extremely high energy density. But the use of a metallic‐Li anode causes serious safety hazards, such as short‐circuiting and explosion of the cells. Replacing a sulfur cathode with a fully‐lithiated lithium sulfide (Li₂S) to pair with metallic‐Li‐free high‐capacity anodes paves a feasible way to address this issue. However, the practical utility of Li₂S cathodes faces the challenges of poor conductivity, sluggish activation process, and high sensitivity to moisture and oxygen that make electrode production more difficult than dealing with sulfur cathodes. Here, an efficient but low‐cost strategy for easy production of freestanding flexible Li₂S‐based paper electrodes with very high mass and capacity loading in terms of in situ carbonthermal reduction of Li₂SO₄ by electrospinning carbon is reported. This chemistry enables high loading but strong affinity of ultrafine Li₂S nanoparticles in a freestanding conductive carbon‐nanofiber network, meanwhile greatly reducing the manufacturing complexity and cost of Li₂S cathodes. Benefiting from enhanced structural stability and reaction kinetics, the areal specific capacities of such cathodes can be significantly boosted with less sacrificing of high‐rate and cycling capability. This unique Li₂S‐cathode design can be directly applied for constructing metallic‐Li‐free or flexible Li–S batteries with high‐energy density.     

Polysulfide‐Shuttle Control in Lithium‐Sulfur Batteries with a Chemically/Electrochemically Compatible NaSICON‐Type Solid Electrolyte

A NaSICON‐type Li⁺‐ion conductive membrane with a formula of Li_{1+ x} Y _x Zr_{2? x} (PO₄)₃ (LYZP) (x = 0–0.15) has been explored as a solid‐electrolyte/separator to suppress polysulfide‐crossover in lithium‐sulfur (Li‐S) batteries. The LYZP membrane with a reasonable Li⁺‐ion conductivity shows both favorable chemical compatibility with the lithium polysulfide species and exhibits good electrochemical stability under the operating conditions of the Li‐S batteries. Through an integration of the LYZP solid electrolyte with the liquid electrolyte, the hybrid Li‐S batteries show greatly enhanced cyclability in contrast to the conventional Li‐S batteries with the porous polymer (e.g., Celgard) separator. At a rate of C/5, the hybrid Li ||LYZP|| Li₂S₆ batteries developed in this study (with a Li‐metal anode, a liquid/LYZP hybrid electrolyte, and a dissolved lithium polysulfide cathode) delivers an initial discharge capacity of ≈1000 mA h g^?1 (based on the active sulfur material) and retains ≈90% of the initial capacity after 150 cycles with a low capacity fade‐rate of <0.07% per cycle.     

MoN Supported on Graphene as a Bifunctional Interlayer for Advanced Li‐S Batteries

Rational design of effective polysulfide barriers is highly important for high‐performance lithium‐sulfur (Li‐S) batteries. A variety of adsorbents have been applied as interlayers to alleviate the shuttle effect. Nevertheless, the unsuccessful oxidation of Li₂S on interlayers leads to loss of active materials and blocks Li ion transport. In this work, a MoN‐based interlayer sandwiched between the C‐S cathode and the separator is developed. Such an interlayer not only strongly binds lithium polysulfides via Mo‐S bonding but also efficiently accelerates the decomposition of Li₂S. The acceleration mechanism toward Li₂S decomposition is determined to be a combination of contributions of catalytic cleavage of Li‐S bond in Li₂S based on the proposed covalence‐activation mechanism and rapid migration of the produced Li ions. As a result, the C–S cathodes with the as‐developed interlayer manifest a negligible charging potential barrier and outstanding cycling stability with a very low capacity fading rate of 0.023% per cycle during 1500 cycles at 1 C. High areal capacity of 6.02 mAh cm^?2 is achieved for high sulfur loading of 7.0 mg cm^?2 after cycling at 0.1 C. The material and strategy demonstrated in this work can open the door toward developing shuttle suppression interlayers without impairing cathode performance.     

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

Safety and the polysulfide shuttle reaction are two major challenges for liquid electrolyte lithium–sulfur (Li–S) batteries. Although use of solid‐state electrolytes can overcome these two challenges, it also brings new challenges by increasing the interface resistance and stress/strain. In this work, the interface resistance and stress/strain of sulfur cathodes are significantly reduced by conformal coating ≈2 nm sulfur (S) onto reduced graphene oxide (rGO). An Li–S full cell consisting of an rGO@S‐Li₁₀GeP₂S₁₂‐acetylene black (AB) composite cathode is evaluated. At 60 °C, the all‐solid‐state Li–S cell demonstrates a similar electrochemical performance as in liquid organic electrolyte, with high rate capacities of 1525.6, 1384.5, 1336.3, 903.2, 502.6, and 204.7 mA h g^?1 at 0.05, 0.1, 0.5, 1.0, 2.0, and 5.0 C, respectively. It can maintain a high and reversible capacity of 830 mA h g^?1 at 1.0 C for 750 cycles. The uniform distribution of the rGO@S nanocomposite in the Li₁₀GeP₂S₁₂‐AB matrix generates uniform volume changes during lithiation/delithiation, significantly reducing the stress/strain, thus extending the cycle life. Minimization of the stress/strain of solid cells is the key for a long cycle life of all‐solid‐state Li–S batteries.     

Incorporating Solvate and Solid Electrolytes for All‐Solid‐State Li2S Batteries with High Capacity and Long Cycle Life

The development of all‐solid‐state lithium–sulfur batteries is hindered by the poor interfacial properties at solid electrolyte (SE)/electrode interfaces. The interface is modified by employing the highly concentrated solvate electrolyte, (MeCN)₂?LiTFSI:TTE, as an interlayer material at the electrolyte/electrode interfaces. The incorporation of an interlayer significantly improves the cycling performance of solid‐state Li₂S batteries compared to the bare counterpart, exhibiting a specific capacity of 760 mAh g^?1 at cycle 100 (330 mAh g^?1 for the bare cell). Electrochemical impedance spectroscopy shows that the interfacial resistance of the interlayer‐modified cell gradually decreases as a function of cycle number, while the impedance of the bare cell remains almost constant. Cross‐section scanning electron microscopy (SEM)/ energy dispersive X‐ray spectroscopy (EDS) measurements on the interlayer‐modified cell confirm the permeation of solvate into the cathode and the SE with electrochemical cycling, which is related to the decrease in cell impedance. In order to mimic the full permeation of the solvate across the entire cell, the solvate is directly mixed with the SE to form a “solvSEM” electrolyte. The hybrid Li₂S cell using a solvSEM electrolyte exhibits superior cycling performance compared to the solid‐state cells, in terms of Li₂S loading, Li₂S utilization, and cycling stability. The improved performance is due to the favorable ionic contact at the battery interfaces.     

Toward a Reversible Calcium‐Sulfur Battery with a Lithium‐Ion Mediation Approach

Calcium represents a promising anode for the development of high‐energy‐density, low‐cost batteries. However, a lack of suitable electrolytes has restricted the development of rechargeable batteries with a Ca anode. Furthermore, to achieve a high energy density system, sulfur would be an ideal cathode to couple with the Ca anode. Unfortunately, a reversible calcium‐sulfur (Ca‐S) battery has not yet been reported. Herein, a basic study of a reversible nonaqueous room‐temperature Ca‐S battery is presented. The reversibility of the Ca‐S chemistry and high utilization of the sulfur cathode are enabled by employing a Li⁺‐ion‐mediated calcium‐based electrolyte. Mechanistic insights pursued by spectroscopic, electrochemical, microscopic, and theoretical simulation (density functional theory) investigations imply that the Li⁺‐ions in the Ca‐electrolyte stimulate the reactivation of polysulfide/sulfide species. The coordination of lithium to sulfur reduces the formation of sturdy Ca‐S ionic bonds, thus boosting the reversibility of the Ca‐S chemistry. In addition, the presence of Li⁺‐ions facilitates the ionic charge transfer both in the electrolyte and across the solid electrolyte interphase layer, consequently reducing the interfacial and bulk impedance of Ca‐S batteries. As a result, both the utilization of active sulfur in the cathode and the discharge voltage of Ca‐S batteries are significantly improved.     

Ultrafine Co3Se4 Nanoparticles in Nitrogen‐Doped 3D Carbon Matrix for High‐Stable and Long‐Cycle‐Life Lithium Sulfur Batteries

Lithium–sulfur batteries are a promising high energy output solution for substitution of traditional lithium ion batteries. In recent times research in this field has stepped into the exploration of practical applications. However, their applications are impeded by cycling stability and short life‐span mainly due to the notorious polysulfide shuttle effect. In this work, a multifunctional sulfur host fabricated by grafting highly conductive Co₃Se₄ nanoparticles onto the surface of an N‐doped 3D carbon matrix to inhibit the polysulfide shuttle and improve the sulfur utilization is proposed. By regulating the carbon matrix and the Co₃Se₄ distribution, N‐CN‐750@Co₃Se₄‐0.1 m with abundant polar sites is experimentally and theoretically shown to be a good LiPSs absorbent and a sulfur conversion accelerator. The S/N‐CN‐750@Co₃Se₄‐0.1 m cathode shows excellent sulfur utilization, rate performance, and cyclic durability. A prolonged cycling test of the as‐fabricated S/N‐CN‐750@Co₃Se₄‐0.1 m cathode is carried out at 0.2 C for more than 5 months which delivers a high initial capacity of 1150.3 mAh g^?1 and retains 531.0 mAh g^?1 after 800 cycles with an ultralow capacity reduction of 0.067% per cycle, maintaining Coulombic efficiency of more than 99.3%. The reaction details are characterized and analyzed by ex situ measurements. This work highly emphasizes the potential capabilities of transition‐metal selenides in lithium–sulfur batteries.     

Optimized Catalytic WS2–WO3 Heterostructure Design for Accelerated Polysulfide Conversion in Lithium–Sulfur Batteries

The lithium–sulfur (Li–S) battery is a next generation high energy density battery, but its practical application is hindered by the poor cycling stability derived from the severe shuttling of lithium polysulfides (LiPSs). Catalysis is a promising way to solve this problem, but the rational design of relevant catalysts is still hard to achieve. This paper reports the WS₂–WO₃ heterostructures prepared by in situ sulfurization of WO₃, and by controlling the sulfurization degree, the structure is controlled, which balances the trapping ability (by WO₃) and catalytic activity (by WS₂) toward LiPSs. As a result, the WS₂–WO₃ heterostructures effectively accelerate LiPS conversion and improve sulfur utilization. The Li–S battery with 5 wt% WS₂–WO₃ heterostructures as additives in the cathode shows an excellent rate performance and good cycling stability, revealing a 0.06% capacity decay each cycle over 500 cycles at 0.5 C. By building an interlayer with such heterostructure‐added graphenes, the battery with a high sulfur loading of 5 mg cm^?2 still shows a high capacity retention of 86.1% after 300 cycles at 0.5 C. This work provides a rational way to prepare the metal oxide–sulfide heterostructures with an optimized structure to enhance the performance of Li–S batteries.     

Boosting Polysulfide Redox Kinetics by Graphene‐Supported Ni Nanoparticles with Carbon Coating

Lithium–sulfur batteries have attracted extensive attention because of their high energy density. However, their application is still impeded by the inherent sluggish kinetics and solubility of intermediate products (i.e., polysulfides) of the sulfur cathode. Herein, graphene‐supported Ni nanoparticles with a carbon coating are fabricated by directly carbonizing a metal–organic framework/graphene oxide composite, which is then dispersed on a commercial glass fiber membrane to form a separator with electrocatalytic activity. In situ analysis and electrochemical investigation demonstrate that this modified separator can effectively suppress the shuttle effect and regulate the catalytic conversion of intercepted polysulfides, which is also confirmed by density functional theory calculations. It is found that Ni–C sites can chemically interact with polysulfides and stabilize the radical S₃^?? through Ni? S bonds to enable fast dynamic equilibrium with S₆^2?, while Ni nanoparticles reduce the oxidation barrier of Li₂S and accelerate ion/electron transport. As a result, the corresponding lithium–sulfur battery shows a high cycle stability (88% capacity retention over 100 cycles) even with a high sulfur mass loading of 8 mg cm^?2 and lean electrolyte (6.25 µ L mg^?1). Surprisingly, benefitting from the improved kinetics, the battery can work well at ?50 °C, which is rarely achieved by conventional Li–S batteries.     

An Efficient Separator with Low Li‐Ion Diffusion Energy Barrier Resolving Feeble Conductivity for Practical Lithium–Sulfur Batteries

Due to unprecedented features including high‐energy density, low cost, and light weight, lithium–sulfur batteries have been proposed as a promising successor of lithium‐ion batteries. However, unresolved detrimental low Li‐ion transport rates in traditional carbon materials lead to large energy barrier in high sulfur loading batteries, which prevents the lithium–sulfur batteries from commercialization. In this report, to overcome the challenge of increasing both the cycling stability and areal capacity, a metallic oxide composite (NiCo₂O₄@rGO) is designed to enable a robust separator with low energy barrier for Li‐ion diffusion and simultaneously provide abundant active sites for the catalytic conversion of the polar polysulfides. With a high sulfur‐loading of 6 mg cm^?2 and low sulfur/electrolyte ratio of 10, the assembled batteries deliver an initial capacity of 5.04 mAh cm^?2 as well as capacity retention of 92% after 400 cycles. The metallic oxide composite NiCo₂O₄@rGO/PP separator with low Li‐ion diffusion energy barrier opens up the opportunity for lithium–sulfur batteries to achieve long‐cycle, cost‐effective operation toward wide applications in electric vehicles and electronic devices.     

In Situ Generation of Artificial Solid‐Electrolyte Interphases on 3D Conducting Scaffolds for High‐Performance Lithium‐Metal Anodes

Rational structure design of the current collector along with further engineering of the solid‐electrolyte interphases (SEI) layer is one of the most promising strategies to achieve uniform Li deposition and inhibit uncontrolled growth of Li dendrites. Here, a Li₂S layer as an artificial SEI with high compositional uniformity and high lithium ion conductivity is in situ generated on the surface of the 3D porous Cu current collector to regulate homogeneous Li plating/stripping. Both simulations and experiments demonstrate that the Li₂S protective layer can passivate the porous Cu skeleton and balance the transport rate of lithium ions and electrons, thereby alleviating the agglomerated Li deposition at the top of the electrode or at the defect area of the SEI layer. As a result, the modified current collector exhibits long‐term cycling of 500 cycles at 1 mA cm^?2 and stable electrodeposition capabilities of 4 mAh cm^?2 at an ultrahigh current density of 4 mA cm^?2. Furthermore, full batteries (LiFePO₄ as cathode) paired with this designed 3D anode with only ≈200% extra lithium show superior stability and rate performance than the batteries paired with lithium foil (≈3000% extra lithium). These explorations provide new strategies for developing high‐performance Li metal anodes.     

Interfacial Charge Field in Hierarchical Yolk–Shell Nanocapsule Enables Efficient Immobilization and Catalysis of Polysulfides Conversion

Inhibiting the shuttle effect of lithium polysulfides and accelerating their conversion kinetics are crucial for the development of high‐performance lithium–sulfur (Li–S) batteries. Herein, a modified template method is proposed to synthesize the robust yolk–shell sulfur host that is constructed by enveloping dispersive Fe₂O₃ nanoparticles within Mn₃O₄ nanosheet‐grafted hollow N‐doped porous carbon capsules (Fe₂O₃@N‐PC/Mn₃O₄‐S). When applied as a cathode for Li–S batteries, the as‐prepared Fe₂O₃@N‐PC/Mn₃O₄‐S can deliver capacities as high as 1122 mAh g^?1 after 200 cycles at 0.5 C and 639 mAh g^?1 after 1500 cycles at 10 C, respectively. Remarkably, even as the areal sulfur loading is increased to 5.1 mg cm^?2, the cathode can still maintain a high areal specific capacity of 5.08 mAh cm^?2 with a fading rate of only 0.076% per cycle over 100 cycles at 0.1 C. By a further combination analysis of electron holography and electron energy loss spectroscopy, the outstanding performance is revealed to be mainly traced to the oxygen‐vacancy‐induced interfacial charge field, which immobilizes and catalyzes the conversion of lithium polysulfides, assuring low polarization, fleet redox reaction kinetics, and sufficient utilization of sulfur. These new findings may shed light on the dependence of electrochemical performance on the heterostructure of sulfur hosts.