3D Printing Quasi‐Solid‐State Asymmetric Micro‐Supercapacitors with Ultrahigh Areal Energy Density

A 3D printing approach is first developed to fabricate quasi‐solid‐state asymmetric micro‐supercapacitors to simultaneously realize the efficient patterning and ultrahigh areal energy density. Typically, cathode, anode, and electrolyte inks with high viscosities and shear‐thinning rheological behaviors are first prepared and 3D printed individually on the substrates. The 3D printed asymmetric micro‐supercapacitor with interdigitated electrodes exhibits excellent structural integrity, a large areal mass loading of 3.1 mg cm^?2, and a wide electrochemical potential window of 1.6 V. Consequently, this 3D printed asymmetric micro‐supercapacitor displays an ultrahigh areal capacitance of 207.9 mF cm^?2. More importantly, an areal energy density of 73.9 µWh cm^?2 is obtained, superior to most reported interdigitated micro‐supercapacitors. It is believed that the efficient 3D printing strategy can be used to construct various asymmetric micro‐supercapacitors to promote the integration in on‐chip energy storage systems.     

All‐Solid‐State On‐Chip Supercapacitors Based on Free‐Standing 4H‐SiC Nanowire Arrays

All‐solid‐state on‐chip SiC supercapacitors (SCs) based on free‐standing SiC nanowire arrays (NWAs) are reported. In comparison to the widely used technique based on the interdigitated fingers, the present strategy can be much more facile for constructing on‐chip SCs devices, which is directly sandwiched with a solid electrolyte layer between two pieces of SiC NWAs film without any substrate. The mass loading of active materials of on‐chip SiC SCs can be up to ≈5.6 mg cm^?2, and the total device thickness is limited in ≈40 µm. The specific area energy and power densities of the SCs device reach 5.24 µWh cm^?2 and 11.2 mW cm^?2, and their specific volume energy and power densities run up to 1.31 mWh cm^–3 and 2.8 W cm^?3, respectively, which are two orders of magnitude higher than those of state‐of‐the‐art SiC‐based SCs, and also much higher than those of other solid‐state carbon‐based SCs ever reported. Furthermore, such on‐chip SCs exhibit superior rate capability and robust stability with over 94% capacitance retention after 10 000 cycles at a scan rate of 100 mV s^?1, representing their high performance in all merits.     

Scalable Water‐Based Production of Highly Conductive 2D Nanosheets with Ultrahigh Volumetric Capacitance and Rate Capability

Highly conductive and ultrathin 2D nanosheets are of importance for the development of portable electronics and electric vehicles. However, scalable production and rational design for highly electronic and ionic conductive 2D nanosheets still remain a challenge. Herein, an industrially adoptable fluid dynamic exfoliation process is reported to produce large quantities of ionic liquid (IL)‐functionalized metallic phase MoS₂ (m‐MoS₂) and defect‐free graphene (Gr) sheets. Hybrid 2D–2D layered films are also fabricated by incorporating Gr sheets into compact m‐MoS₂ films. The incorporated IL functionalities and Gr sheets prevent aggregation and restacking of the m‐MoS₂ sheets, thereby creating efficient and rapid ion and electron pathways in the hybrid films. The hybrid film with a high packing density of 2.02 g cm^?3 has an outstanding volumetric capacitance of 1430.5 F cm^?3 at 1 A g^?1 and an extremely high rate capability of 80% retention at 1000 A g^?1. The flexible supercapacitor assembled using a polymer‐gel electrolyte exhibits excellent resilience to harsh electrochemical and mechanical conditions while maintaining an impressive rate performance and long cycle life. Successful achievement of an ultrahigh volumetric energy density (1.14 W h cm^?3) using an organic electrolyte with a wide cell voltage of ≈3.5 V is demonstrated.     

Mulberry Paper‐Based Supercapacitor Exhibiting High Mechanical and Chemical Toughness for Large‐Scale Energy Storage Applications

In response to the demand for flexible and sustainable energy storage devices that exhibit high electrochemical performance, a supercapacitor system is fabricated using mulberry tree‐derived paper as a substrate and Poly(3,4‐ethylenedioxythiophene)‐poly(styrenesulfonate) (PEDOT:PSS) and carbon black as the active material. The mulberry paper‐based supercapacitor system demonstrates high energy density of 29.8–39.8 Wh kg^?1 and power density of 2.8–13.9 kW kg^?1 with 90.7% retention of its initial capacity over 15 000 charge–discharge cycles. In addition, the mulberry tree fibers are known to have superior mechanical strength and toughness and the mulberry paper‐based supercapacitor; as a result, exhibit high mechanical and chemical toughness; 99% of its initial capacity is retained after 100 repeated applications of bending strains, and twisting. 94% capacity retention is observed even after exposure to HCl and H₂SO₄ acid solutions. The fabrication methodology of the mulberry‐based supercapacitor is highly scalable and could be stacked to increase the energy storage capacity, where operation of light‐emitting diode lights with a drive voltage of 12 V integrated in a wearable device is demonstrated.     

High‐Performance and Breathable Polypyrrole Coated Air‐Laid Paper for Flexible All‐Solid‐State Supercapacitors

High‐performance, breathable, conductive, and flexible polypyrrole (PPy) coated paper electrodes are prepared by an interfacial polymerization method using air‐laid paper as a substrate. Owing to the synergistic effect of superior electrical conductivity, high wettability, and the porous architecture, the prepared electrode not only shows an outstanding specific capacitance and rate abilities (3100 and 2579 mF cm^?2 at 1 and 20 mA cm^?2 for a PPy coated paper electrode), but also exhibits excellent flexibility, wearability, and breathability. Based on these superior features, an all‐solid‐state supercapacitor assembled with the PPy coated paper electrodes shows an outstanding energy density of 62.4 µW h cm^?2, remarkable air permeability and excellent flexibility to sustain various deformations. Furthermore, large‐scale fabrication of conductive flexible paper electrode can be easily achieved through this method. Therefore, this work offers a new vision for flexible energy storage.     

3D‐Printed Stretchable Micro‐Supercapacitor with Remarkable Areal Performance

While stretchable micro‐supercapacitors (MSCs) have been realized, they have suffered from limited areal electrochemical performance, thus greatly restricting their practical electronic application. Herein, a facile strategy of 3D printing and unidirectional freezing of a pseudoplastic nanocomposite gel composed of Ti₃C₂T_x MXene nanosheets, manganese dioxide nanowire, silver nanowires, and fullerene to construct intrinsically stretchable MSCs with thick and honeycomb‐like porous interdigitated electrodes is introduced. The unique architecture utilizes thick electrodes and a 3D porous conductive scaffold in conjunction with interacting material properties to achieve higher loading of active materials, larger interfacial area, and faster ion transport for significantly improved areal energy and power density. Moreover, the oriented cellular scaffold with fullerene‐induced slippage cell wall structure prompts the printed electrode to withstand large deformations without breaking or exhibiting obvious performance degradation. When imbued with a polymer gel electrolyte, the 3D‐printed MSC achieves an unprecedented areal capacitance of 216.2 mF cm^?2 at a scan rate of 10 mV s^?1, and remains stable when stretched up to 50% and after 1000 stretch/release cycles. This intrinsically stretchable MSC also exhibits high rate capability and outstanding areal energy density of 19.2 µWh cm^?2 and power density of 58.3 mW cm^?2, outperforming all reported stretchable MSCs.     

Antimonene Engineered Highly Deformable Freestanding Electrode with Extraordinarily Improved Energy Storage Performance

Advanced 2D materials have spurred great interest as a new paradigm in pursuing improved energy storage performance. Herein, for the first time, antimonene is utilized as an effective active component for constructing highly deformable and editable freestanding film electrodes, as the basis of a supercapacitor with record‐breaking electrode performance. The insertion of antimonene is able to improve the environmental stability of the antimonene/MXene composite electrode and remarkably enhance the energy storage capability in both protic and neutral electrolytes. Notably, an ultrahigh specific volumetric capacitance of 4255 F cm^?3 is achieved by the electrode tested in a1 m H₂SO₄ electrolyte, which represents the state‐of‐the‐art value reported to date for supercapacitor electrodes based on MXenes. The flexible supercapacitors constructed by the composite electrode, also demonstrate highly competitive energy and power densities: 459.75 mWh cm^?3 and 3.12 W cm^?3 for the asymmetrical one with a much widened potential window of 2 V in neutral electrolyte; 112.52 mWh cm^?3 and 1 W cm^?3 for the symmetrical configuration with an outstanding capacitance of 1265 F cm^?3 in acidic media. This work sheds new light on the fabrication of high‐performance supercapacitor electrodes with functionalities in different electrolyte media and various device configurations.     

Versatile N‐Doped MXene Ink for Printed Electrochemical Energy Storage Application

Printing is regarded as a revolutionary and feasible technique to guide the fabrication of versatile functional systems with designed architectures. 2D MXenes are nowadays attractive in printed energy storage devices. However, owing to the van der Waals interaction between the MXene layers, the restacking issues within the printed electrodes can significantly impede the ion/electrolyte transport and hence handicap the electrochemical performances. Herein, a melamine formaldehyde templating method is demonstrated to develop crumpled nitrogen‐doped MXene (MXene‐N) nanosheets. The nitrogen doping boosts the electrochemical performances of MXene via enhanced conductivity and redox activity. Accordingly, two types of MXene‐N inks are prepared throughout the optimization of the ink viscosity to fit the 2D screen printing and 3D extrusion printing, respectively. As a result, the screen printed MXene‐N microsupercapacitor delivers an areal capacitance of 70.1 mF cm^?2 and outstanding mechanical robustness. Furthermore, the 3D‐printed MXene‐N based supercapacitor manifests an areal capacitance of 8.2 F cm^?2 for a three‐layered electrode and readily stores a high areal energy density of 0.42 mWh cm^?2. The approach to harnessing such versatile MXene‐N inks offers distinctive insights into the printed energy storage systems with high areal energy density and large scalability.     

Alkaline Polymer Membrane‐Based Ultrathin,Flexible, and High‐Performance Solid‐State Zn‐Air Battery

The increasing demand for portable and wearable electronics requires lightweight, thin, and highly flexible power sources, for example, flexible zinc‐air batteries (ZABs). The so‐far reported flexible ZAB devices mostly remain bulky, with a design consisting of two relatively thick substrates (e.g., carbon cloths and/or metal foams) and a gel electrolyte‐coated separator in between. Herein, an ultrathin (≈0.2 mm) solid‐state ZAB with high flexibility and performance is introduced by directly forming self‐standing active layers on each surface of an alkaline polymer membrane through an ink‐casting/hot‐pressing approach. A Fe/N‐doped 3D carbon with hierarchic pores and an interconnected network structure is used as cathode electrocatalyst, so that the backing gas‐diffusion layer (e.g., carbon cloth) can be abandoned. What is further, a microstructure‐modulating method to significantly increase the FeN₄ active sites for oxygen reduction reaction is developed, thus significantly boosting the performance of the ZAB. The assembled solid‐state ZAB manifests remarkable peak power density of 250 mW cm^?3 and high capacity of 150.4 mAh cm^?3 at 8.3 mA cm^?3, as well as excellent flexibility. The new design should provide valuable opportunity to the portable and wearable electronics.     

A High‐Performance Monolithic Solid‐State Sodium Battery with Ca2+ Doped Na3Zr2Si2PO12 Electrolyte

Solid‐state sodium batteries (SSSBs) are promising electrochemical energy storage devices due to their high energy density, high safety, and abundant resource of sodium. However, low conductivity of solid electrolyte as well as high interfacial resistance between electrolyte and electrodes are two main challenges for practical application. To address these issues, pure phase Na₃Zr₂Si₂PO₁₂ (NZSP) materials with Ca²⁺ substitution for Zr⁴⁺ are synthesized by a sol‐gel method. It shows a high ionic conductivity of more than 10^?3 S cm^?1 at 25 °C. Moreover, a robust SSSB is developed by integrating sodium metal anodes into NZSP‐type monolithic architecture, forming a 3D electronic and ionic conducting network. The interfacial resistance is remarkably reduced and the monolithic symmetric cell displays stable sodium platting/striping cycles with low polarization for over 600 h. Furthermore, by combining sodium metal anode with Na₃V₂(PO₄)₃ cathode, an SSSB is demonstrated with high rate capability and excellent cyclability. After 450 cycles, the capacity of the cell is still kept at 94.9 mAh g^?1 at 1 C. This unique design of monolithic electrolyte architecture provides a promising strategy toward realizing high‐performance SSSBs.     

Fatigue‐Free and Bending‐Endurable Flexible Mn‐Doped Na0.5Bi0.5TiO3‐BaTiO3‐BiFeO3 Film Capacitor with an Ultrahigh Energy Storage Performance

As the rapid development of intelligent systems moves toward flexible electronics, capacitors with extraordinary flexibility and an outstanding energy storage performance will open up broad prospects for powering portable/wearable electronics and pulsed power applications. This work presents a simple one‐step process to fabricate a flexible Mn‐doped 0.97(0.93Na_0.5Bi_0.5TiO₃‐0.07BaTiO₃)‐0.03BiFeO₃ (Mn:NBT‐BT‐BFO) inorganic thin film capacitor with the assistance of a 2D fluorophlogopite mica substrate. The film element, which has a high breakdown strength, great relaxor dispersion, and the coexistence of ferroelectric and antiferroelectric phases, has a high recoverable energy storage density (W_rec ≈81.9 J cm^?3), high efficiency (η ≈64.4%), superior frequency stability (500 Hz–20 kHz), excellent antifatigue property (1 × 10⁹ cycles), and a broad operating temperature window (25–200 °C). The all‐inorganic Mn:NBT‐BT‐BFO/Pt/mica capacitor has a prominent mechanical‐bending resistance without obvious deterioration in its corresponding energy storage capability when it is subjected to a bending radius of 2 mm or repeated bending for 10³ cycles. This work is the first demonstration of an all‐inorganic flexible film capacitor and sheds light on dielectric energy storage devices for portable/wearable applications.     

Ultrafast All‐Solid‐State Coaxial Asymmetric Fiber Supercapacitors with a High Volumetric Energy Density

Fiber‐supercapacitors (FSCs) are promising energy storage devices that can complement or even replace microbatteries in miniaturized portable and wearable electronics. Currently, a major challenge for FSCs is achieving ultrahigh volumetric energy and power densities simultaneously, especially when the charge/discharge rates exceed 1 V s^?1. Herein, an Au‐nanoparticle‐doped‐MnO_x@CoNi‐alloy@carbon‐nanotube (Au–MnO_x@CoNi@CNT) core/shell nanocomposite fiber electrode is designed, aiming to boost its charge/discharge rate by taking advantage of the superconductive CoNi alloy network and the greatly enhanced conductivity of the Au doped MnO_x active materials. An all‐solid‐state coaxial asymmetric FSC (CAFSC) prototype device made by wrapping this fiber with a holey graphene paper (HGP) exhibits excellent performance at rates up to 10 V s^?1, which is the highest charge rate demonstrated so far for FSCs based on pseudocapacitive materials. Furthermore, our fully packaged CAFSC delivers a volumetric energy density of ≈15.1 mW h cm^?3, while simultaneously maintaining a high power density of 7.28 W cm^?3 as well as a long cycle life (90% retention after 10 000 cycles). This value is the highest among all reported FSCs, even better than that of a typical 4 V/500 µA h thin‐film lithium battery.     

Lignin Laser Lithography: A Direct‐Write Method for Fabricating 3D Graphene Electrodes for Microsupercapacitors

In this work, a simple lignin‐based laser lithography technique is developed and used to fabricate on‐chip microsupercapacitors (MSCs) using 3D graphene electrodes. Specifically, lignin films are transformed directly into 3D laser‐scribed graphene (LSG) electrodes by a simple one‐step CO₂ laser irradiation. This step is followed by a water lift‐off process to remove unexposed lignin, resulting in 3D graphene with the designed electrode patterns. The resulting LSG electrodes are hierarchically porous, electrically conductive (conductivity is up to 66.2 S cm^?1), and have a high specific surface area (338.3 m² g^?1). These characteristics mean that such electrodes can be used directly as MSC electrodes without the need for binders and current collectors. The MSCs fabricated using lignin laser lithography exhibit good electrochemical performances, namely, high areal capacitance (25.1 mF cm^?2), high volumetric energy density (≈1 mWh cm^?3), and high volumetric power density (≈2 W cm^?3). The versatility of lignin laser lithography opens up the opportunity in applications such as on‐chip microsupercapacitors, sensors, and flexible electronics at large‐scale production.     

Graphene‐Indanthrone Donor–π–Acceptor Heterojunctions for High‐Performance Flexible Supercapacitors

To overcome the low energy density bottleneck of graphene‐based supercapacitors and to organically endow them with high‐power density, ultralong‐life cycles, etc., one rational strategy that couple graphene sheets with multielectron, redox‐reversible, and structurally‐stable organic compounds. Herein, a graphene‐indanthrone (IDT) donor–π–acceptor heterojunction is conceptualized for efficient and smooth 6H⁺/6e^? transfers from pseudocapacitive IDT molecules to electrochemical double‐layer capacitive graphene scaffolds. To construct this, water‐processable graphene oxide (GO) is employed as a graphene precursor, and to in situ exfoliate IDT industrial dyestuff, followed by a hydrothermally‐induced reduction toward GO and self‐assembly between reduced GO (rGO) donors (D) and IDT acceptors (A), affording rGO‐π‐IDT D–A heterojunctions. Electrochemical tests indicate that rGO‐π‐IDT heterojunctions deliver a gravimetric capacitance of 535.5 F g^?1 and an amplified volumetric capacitance of 685.4 F cm^?3. The assembled flexible all‐solid‐state supercapacitor yields impressive volumetric energy densities of 31.3 and 25.1 W h L^?1, respectively, at low and high power densities of 767 and 38 554 W L^?1, while exhibiting an exceptional rate capability, cycling stability, and enduring mechanically‐challenging bending and distortions. The concept and methodology may open up opportunities for other two‐dimensional materials and other energy‐related devices.     

Direct Growth of Flower‐Like δ‐MnO2 on Three‐Dimensional Graphene for High‐Performance Rechargeable Li‐O2 Batteries

A challenge still remains to develop high‐performance and cost‐effective air electrode for Li‐O₂ batteries with high capacity, enhanced rate capability and long cycle life (100 times or above) despite recent advances in this field. In this work, a new design of binder‐free air electrode composed of three‐dimensional (3D) graphene (G) and flower‐like δ‐MnO₂ (3D‐G‐MnO₂) has been proposed. In this design, graphene and δ‐MnO₂ grow directly on the skeleton of Ni foam that inherits the interconnected 3D scaffold of Ni foam. Li‐O₂ batteries with 3D‐G‐MnO₂ electrode can yield a high discharge capacity of 3660 mAh g^?1 at 0.083 mA cm^?2. The battery can sustain 132 cycles at a capacity of 492 mAh g^?1 (1000 mAh g_carbon ^?1) with low overpotentials under a high current density of 0.333 mA cm^?2. A high average energy density of 1350 Wh Kg^?1 is maintained over 110 cycles at this high current density. The excellent catalytic activity of 3D‐G‐MnO₂ makes it an attractive air electrode for high‐performance Li‐O₂ batteries.     

Integrated Conductive Hybrid Architecture of Metal–Organic Framework Nanowire Array on Polypyrrole Membrane for All‐Solid‐State Flexible Supercapacitors

Metal–organic frameworks (MOFs) with intrinsically porous structures are promising candidates for energy storage, however, their low electrical conductivity limits their electrochemical energy storage applications. Herein, the hybrid architecture of intrinsically conductive Cu‐MOF nanowire arrays on self‐supported polypyrrole (PPy) membrane is reported for integrated flexible supercapacitor (SC) electrodes without any inactive additives, binders, or substrates involved. The conductive Cu‐MOFs nanowire arrays afford high conductivity and a sufficiently active surface area for the accessibility of electrolyte, whereas the PPy membrane provides decent mechanical flexibility, efficient charge transfer skeleton, and extra capacitance. The all‐solid‐state flexible SC using integrated hybrid electrode demonstrates an exceptional areal capacitance of 252.1 mF cm^?2, an energy density of 22.4 µWh cm^?2, and a power density of 1.1 mW cm^?2, accompanied by an excellent cycle capability and mechanical flexibility over a wide range of working temperatures. This work not only presents a robust and flexible electrode for wide temperature range operating SC but also offers valuable concepts with regards to designing MOF‐based hybrid materials for energy storage and conversion systems.     

High‐Performance Fiber‐Shaped All‐Solid‐State Asymmetric Supercapacitors Based on Ultrathin MnO2 Nanosheet/Carbon Fiber Cathodes for Wearable Electronics

Flexible fiber‐shaped supercapacitors have shown great potential in portable and wearable electronics. However, small specific capacitance and low operating voltage limit the practical application of fiber‐shaped supercapacitors in high energy density devices. Herein, direct growth of ultrathin MnO₂ nanosheet arrays on conductive carbon fibers with robust adhesion is exhibited, which exhibit a high specific capacitance of 634.5 F g^?1 at a current density of 2.5 A g^?1 and possess superior cycle stability. When MnO₂ nanosheet arrays on carbon fibers and graphene on carbon fibers are used as a positive electrode and a negative electrode, respectively, in an all‐solid‐state asymmetric supercapacitor (ASC), the ASC displays a high specific capacitance of 87.1 F g^?1 and an exceptional energy density of 27.2 Wh kg^?1. In addition, its capacitance retention reaches 95.2% over 3000 cycles, representing the excellent cyclic ability. The flexibility and mechanical stability of these ASCs are highlighted by the negligible degradation of their electrochemical performance even under severely bending states. Impressively, as‐prepared fiber‐shaped ASCs could successfully power a photodetector based on CdS nanowires without applying any external bias voltage. The excellent performance of all‐solid‐state ASCs opens up new opportunity for development of wearable and self‐powered nanodevices in near future.     

All‐Printed MnHCF‐MnOx‐Based High‐Performance Flexible Supercapacitors

Here, a simple active materials synthesis method is presented that boosts electrode performance and utilizes a facile screen‐printing technique to prepare scalable patterned flexible supercapacitors based on manganese hexacyanoferrate‐manganese oxide and electrochemically reduced graphene oxide electrode materials (MnHCF‐MnO_x/ErGO). A very simple in situ self‐reaction method is developed to introduce MnO_x pseudocapacitor material into the MnHCF system by using NH₄F. This MnHCF‐MnO_x electrode materials can deliver excellent capacitance of 467 F g^?1 at a current density of 1 A g^?1, which is a 2.4 times capacitance increase compared to MnHCF. In addition a printed, patterned, flexible MnHCF‐MnO_x/ErGO supercapacitor is fabricated, showing a remarkable areal capacitance of 16.8 mF cm^?2 and considerable energy and power density of 0.5 mWh cm^?2 and 0.0023 mW cm^?2, respectively. Furthermore, the printed patterned flexible supercapacitors also exhibit exceptional flexibility, and the capacitance remains stable, even while bending to various angles (60°, 90°, and 180°) and for 100 cycles. The flexible supercapacitor arrays integrated by multiple prepared single supercapacitors can power various LEDs even in the bent states. This approach offers promising opportunities for the development of printable energy storage materials and devices with high energy density, large scalability, and excellent flexibility.     

Flexible and Stretchable Biobatteries: Monolithic Integration of Membrane‐Free Microbial Fuel Cells in a Single Textile Layer

The fabrication and performance of a flexible and stretchable microbial fuel cell (MFC) monolithically integrated into a single sheet of textile substrate are reported. The single‐layer textile MFC uses Pseudomonas aeruginosa (PAO1) as a biocatalyst to produce a maximum power of 6.4 µW cm^?2 and current density of 52 µA cm^?2, which are substantially higher than previous textile‐MFCs and are similar to other flexible paper‐based MFCs. The textile MFC demonstrates a stable performance with repeated stretching and twisting cycles. The membrane‐less single‐chamber configuration drastically simplifies the fabrication and improves the performance of the MFC. A conductive and hydrophilic anode in a 3D fabric microchamber maximizes bacterial electricity generation from a liquid environment and a silver oxide/silver solid‐state cathode reduces cathodic overpotential for fast catalytic reaction. A simple batch fabrication approach simultaneously constructs 35 individual devices, which will revolutionize the mass production of textile MFCs. This stretchable and twistable power device printed directly onto a single textile substrate can establish a standardized platform for textile‐based biobatteries and will be potentially integrated into wearable electronics in the future.     

Achieving Both Enhanced Voltage and Current through Fine‐Tuning Molecular Backbone and Morphology Control in Organic Solar Cells

It is a great challenge to simultaneously improve the two tangled parameters, open circuit voltage (V_oc) and short circuit current density (J_sc) for organic solar cells (OSCs). Herein, such a challenge is addressed by a synergistic approach using fine‐tuning molecular backbone and morphology control simultaneously by a simple yet effective side chain modulation on the backbone of an acceptor–donor–acceptor (A–D–A)‐type acceptor. With this, two terthieno[3,2‐b]thiophene (3TT) based A–D–A‐type acceptors, 3TT‐OCIC with backbone modulation and 3TT‐CIC without such modification, are designed and synthesized. Compared with the controlled molecule 3TT‐CIC, 3TT‐OCIC shows power conversion efficiency (PCE) of 13.13% with improved V_oc of 0.69 V and J_sc of 27.58 mA cm^?2, corresponding to PCE of 12.15% with V_oc of 0.65 V and J_sc of 27.04 mA cm^?2 for 3TT‐CIC–based device. Furthermore, with effective near infrared absorption, 3TT‐OCIC is used as the rear subcell acceptor in a tandem device and gave an excellent PCE of 15.72%.