Biomass‐Derived 3D Carbon Aerogel with Carbon Shell‐Confined Binary Metallic Nanoparticles in CNTs as an Efficient Electrocatalyst for Microfluidic Direct Ethylene Glycol Fuel Cells

Flexible and 3D carbon aerogels (CAs) composed of carbon nanotubes (CNTs) with carbon shell‐confined binary palladium–nickel (Pd_x–Ni_y) nanocatalysts on carbon fibers (Pd_x–Ni_y/NSCNT/CA) have been developed through a facile chemical vapor deposition method. The 3D porous carbon network and the synergistic effect of carbon shell‐confined bimetal nanoparticles of rationally constructed aerogels facilitate enhanced electrocatalytic and antipoisoning activities toward ethylene glycol (EG) oxidation reaction compared to the commercial Pt/C catalyst. With the 3D morphological features and direct growth of Pd–Ni bimetallic nanoparticles encapsulated CNTs on carbon fibers, the Pd₅₂–Ni₄₈/NSCNT/CA delivers a maximum microfluidic direct ethylene glycol fuel cell (µDEGFC) power density and durability of, respectively, 62.8 mW cm^?2 and 60 h. The superior performance observed, with Pd₅₂–Ni₄₈/NSCNT/CA amongst the catalysts reported in the literature, opens an exciting research avenue towards powering next‐generation, portable electronics.     

Pt‐Ir‐Pd Trimetallic Nanocages as a Dual Catalyst for Efficient Oxygen Reduction and Evolution Reactions in Acidic Media

The development of dual catalysts with high efficiency toward oxygen reduction and evolution reactions (ORR and OER) in acidic media is a significant challenge. Here an active and durable dual catalyst based upon cubic Pt₃₉Ir₁₀Pd₁₁ nanocages with an average edge length of 12.3 nm, porous walls as thin as 1.0 nm, and well‐defined {100} facets is reported. The trimetallic nanocages perform better than all the reported dual catalysts in acidic media, with a low ORR‐OER overpotential gap of only 704 mV at a Pt‐Ir‐Pd loading of 16.8 µg_Pt+Ir+Pd cm^?2_geo. For ORR at 0.9 V, when benchmarked against the commercial Pt/C and Pt‐Pd nanocages, the trimetallic nanocages exhibit an enhanced mass activity of 0.52 A mg^?1_Pt+Ir+Pd (about four and two times as high as those of the Pt/C and Pt‐Pd nanocages) and much improved durability. For OER, the trimetallic nanocages show a remarkable mass activity of 0.20 A mg^?1_Pt+Ir at 1.53 V, which is 16.7 and 4.3 fold relative to those of the Pt/C and Pt‐Pd nanocages, respectively. These improvements can be ascribed to the highly open structure of the nanocages, and the possible electronic coupling between Ir and Pt atoms in the lattice.     

Sequential Synthesis and Active‐Site Coordination Principle of Precious Metal Single‐Atom Catalysts for Oxygen Reduction Reaction and PEM Fuel Cells

Carbon‐supported precious metal single‐atom catalysts (PM SACs) have shown promising application in proton exchange membrane fuel cells (PEMFCs). However, the coordination principle of the active site, consisting of one PM atom and several coordinating anions, is still unclear for PM SACs. Here, a sequential coordination method is developed to dope a large amount of PM atoms (Ir, Rh, Pt and Pd) into a zeolite imidazolate framework (ZIF), which are further pyrolyzed into nitrogen‐coordinated PM SACs. The PM loadings are as high as 1.2–4.5 wt%, achieving the highest PM loadings in ZIF‐derived SACs to date. In the acidic half‐cell, Ir₁‐N/C and Rh₁‐N/C exhibit much higher oxygen reduction reaction (ORR) activities than nanoparticle catalysts Ir/C and Rh/C. In the contrast, the activities of Pd₁‐N/C and Pt₁‐N/C are considerably lower than Pd/C and Pt/C. Density function theory (DFT) calculations reveal that the ORR activity of PM SAC depends on the match between the OH* adsorption on PM and the electronegativity of coordinating anions, and the stronger OH* adsorption is, the higher electronegativity is needed for the coordinating anions. PEMFC tests confirm the active‐site coordination principle and show the extremely high atomic efficiency of Ir₁‐N/C. The revealed principle provides guidance for designing future PM SACs for PEMFCs.     

Biaxial Strains Mediated Oxygen Reduction Electrocatalysis on Fenton Reaction Resistant L10‐PtZn Fuel Cell Cathode

PtM alloy catalysts (e.g., PtFe, PtCo), especially in an intermetallic L1₀ structure, have attracted considerable interest due to their respectable activity and stability for the oxygen reduction reaction (ORR) in proton exchange membrane fuel cells (PEMFCs). However, metal‐catalyzed formation of ·OH from H₂O₂ (i.e., Fenton reaction) by Fe‐ or Co‐containing catalysts causes severe degradation of PEM/catalyst layers, hindering the prospects of commercial applications. Zinc is known as an antioxidant in Fenton reaction, but is rarely alloyed with Pt owing to its relatively negative redox potential. Here, sub‐4 nm intermetallic L1₀‐PtZn nanoparticles (NPs) are synthesized as high‐performance PEMFC cathode catalysts. In PEMFC tests, the L1₀‐PtZn cathode achieves outstanding activity (0.52 A mg_Pt^?1 at 0.9 V_iR‐free, and peak power density of 2.00 W cm^?2) and stability (only 16.6% loss in mass activity after 30 000 voltage cycles), exceeding the U.S. DOE 2020 targets and most of the reported ORR catalysts. Density function theory calculations reveal that biaxial strains developed upon the disorder‐order (A1? L1₀) transition of PtZn NPs would modulate the surface Pt? Pt distances and optimize Pt? O binding for ORR activity enhancement, while the increased vacancy formation energy of Zn atoms in an ordered structure accounts for the improved stability.     

Highly Efficient Oxygen Reduction Reaction Activity of Graphitic Tube Encapsulating Nitrided CoxFey Alloy

Nonprecious metals are promising catalysts to avoid the sluggish oxygen reduction reaction (ORR) in next‐generation regenerative fuel cells or metal–air batteries. Therefore, development of nonprecious metal catalysts for ORR is highly desirable. Herein, precise tuning of the atomic ratio of Fe and Co encapsulated in melamine‐derived nitrogen‐rich graphitic tube (NGT) is reported. The Co_1.08Fe_3.34 hybrid with metal? nitrogen bonds ( 1 : Co_1.08Fe_3.34@NGT) shows remarkable ORR catalytic activities (80 mV higher in onset potential and 50 mV higher in half‐wave potential than those of state‐of‐the‐art commercial Pt/C catalysts), high current density, and stability. In acidic solution, 1 also shows compatible performance to commercial Pt/C in terms of ORR activity, current density, stability, and methanol tolerance. The high ORR activity is ascribed to the co‐existence of Fe? N, Co? N, and sufficient metallic FeCo alloys which favor faster electron movement and better adsorption of oxygen molecules on the catalyst surface. In the alkaline anion exchange membrane fuel cell setup, this cell delivers the power density of 117 mW cm^?2, demonstrating its potential use for energy conversion and storage applications.     

Single‐Atom to Single‐Atom Grafting of Pt1 onto FeN4 Center: Pt1@FeNC Multifunctional Electrocatalyst with Significantly Enhanced Properties

Nonprecious metal catalysts (NPMCs) Fe?N?C are promising alternatives to noble metal Pt as the oxygen reduction reaction (ORR) catalysts for proton‐exchange‐membrane fuel cells. Herein, a new modulation strategy is reported to the active moiety Fe?N₄ via a precise “single‐atom to single‐atom” grafting of a Pt atom onto the Fe center through a bridging oxygen molecule, creating a new active moiety of Pt₁?O₂?Fe₁?N₄. The modulated Fe?N?C exhibits remarkably improved ORR stabilities in acidic media. Moreover, it shows unexpectedly high catalytic activities toward oxygen evolution reaction (OER) and hydrogen evolution reaction (HER), with overpotentials of 310 mV for OER in alkaline solution and 60 mV for HER in acidic media at a current density of 10 mA cm^?2, outperforming the benchmark RuO₂ and comparable with Pt/C(20%), respectively. The enhanced multifunctional electrocatalytic properties are associated with the newly constructed active moiety Pt₁?O₂?Fe₁?N₄, which protects Fe sites from harmful species. Density functional theory calculations reveal the synergy in the new active moiety, which promotes the proton adsorption and reduction kinetics. In addition, the grafted Pt₁?O₂? dangling bonds may boost the OER activity. This study paves a new way to improve and extend NPMCs electrocatalytic properties through a precisely single‐atom to single‐atom grafting strategy.     

Single‐Atom to Single‐Atom Grafting of Pt1 onto Fe?N4 Center: Pt1@Fe?N?C Multifunctional Electrocatalyst with Significantly Enhanced Properties

Nonprecious metal catalysts (NPMCs) Fe? N? C are promising alternatives to noble metal Pt as the oxygen reduction reaction (ORR) catalysts for proton‐exchange‐membrane fuel cells. Herein, a new modulation strategy is reported to the active moiety Fe? N₄ via a precise “single‐atom to single‐atom” grafting of a Pt atom onto the Fe center through a bridging oxygen molecule, creating a new active moiety of Pt₁? O₂? Fe₁? N₄. The modulated Fe? N? C exhibits remarkably improved ORR stabilities in acidic media. Moreover, it shows unexpectedly high catalytic activities toward oxygen evolution reaction (OER) and hydrogen evolution reaction (HER), with overpotentials of 310 mV for OER in alkaline solution and 60 mV for HER in acidic media at a current density of 10 mA cm^?2, outperforming the benchmark RuO₂ and comparable with Pt/C(20%), respectively. The enhanced multifunctional electrocatalytic properties are associated with the newly constructed active moiety Pt₁? O₂? Fe₁? N₄, which protects Fe sites from harmful species. Density functional theory calculations reveal the synergy in the new active moiety, which promotes the proton adsorption and reduction kinetics. In addition, the grafted Pt₁? O₂? dangling bonds may boost the OER activity. This study paves a new way to improve and extend NPMCs electrocatalytic properties through a precisely single‐atom to single‐atom grafting strategy.     

Bimetallic Zeolitic Imidazolite Framework Derived Carbon Nanotubes Embedded with Co Nanoparticles for Efficient Bifunctional Oxygen Electrocatalyst

Bifunctional oxygen catalysts for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) with high activities and low‐cost are of prime importance and challenging in the development of fuel cells and rechargeable metal–air batteries. This study reports a porous carbon nanomaterial loaded with cobalt nanoparticles (Co@NC‐x/y) derived from pyrolysis of a Co/Zn bimetallic zeolitic imidazolite framework, which exhibits incredibly high activity as bifunctional oxygen catalysts. For instance, the optimal catalyst of Co@NC‐3/1 has the interconnected framework structure between porous carbon and embedded carbon nanotubes, which shows the superb ORR activity with onset potential of ≈1.15 V and half‐wave potential of ≈0.93 V. Moreover, it presents high OER activity that can be further enhanced to over commercial RuO₂ by P‐doped with overpotentials of 1.57 V versus reversible hydrogen electrode at 10 mA cm^?2 and long‐term stability for 2000 circles and a Tafel slope of 85 mV dec^?1. Significantly, the nanomaterial demonstrates better catalytic performance and durability than Pt/C for ORR and commercial RuO₂ and IrO₂ for OER. These findings suggest the importance of a synergistic effect of graphitic carbon, nanotubes, exposed Co–N_x active sites, and interconnected framework structure of various carbons for bifunctional oxygen electrocatalysts.     

Carbon Nanodot Surface Modifications Initiate Highly Efficient,Stable Catalysts for Both Oxygen Evolution and Reduction Reactions

Efficient, stable, and low‐cost electrocatalysts for the oxygen evolution and reduction reactions (OER and ORR) are essential components of energy conversion. Although much progress has been achieved in the development of platinum‐based electrocatalysts for ORR and iridium‐based electrocatalysts for OER, they are still not yet viable for large‐scale commercialization because of the high cost and scanty supply of the noble metals. Here, it is demonstrated that carbon nanodots surface‐modified with either phosphorus or amidogen can respectively achieve electrocatalytic activity approaching that of the benchmark Pt/C and IrO₂ /C catalysts for ORR and OER. Furthermore, phosphorus (amidogen)‐modified carbon nanodots with attached Au nanoparticles exhibit superior ORR (OER) activity better than commercial Pt/C (IrO₂/C) catalysts as well as excellent electrochemical stability under visible light.     

Highly Active and Durable Pt72Ru28 Porous Nanoalloy Assembled with Sub‐4.0 nm Particles for Methanol Oxidation

The main challenges to the direct methanol fuel cells are the activity and durability of electrocatalysts. To alleviate such issues, a recently proposed strategy introduces an exotic element to form Pt‐based alloy nanostructures. This study reports a green route to prepare porous flowerlike Pt₇₂Ru₂₈ nanoalloys assembled with sub‐4.0 nm particles. The peak current density and mass activity on these as‐synthesized porous flowerlike Pt₇₂Ru₂₈ nanoalloys can be increased to 10.98 mA cm^?2 and 1.70 A mg^?1 Pt for methanol oxidation in acidic medium. They are respectively 4.19/3.54, 4.27/5.0, and 5.74/1.73 times those on the commercial Pt black, Pt₅₀Ru₅₀ black, and Ru₅₀Pt₅₀/C. These porous flowerlike Pt₇₂Ru₂₈ nanoalloys have a much higher long‐term durability than commercial Pt black, Pt₅₀Ru₅₀ black, and Ru₅₀Pt₅₀/C. More significantly, the porous Pt₇₂Ru₂₈ bimetallic nanoalloys have long‐term solvent durability after immersion in water for 16 months. The peak current density and mass activity on porous Pt₇₂Ru₂₈ nanoalloys are still 7.76 mA cm^?2 and 1.2 A mg^?1 Pt. These experimental results show an effective approach to the development of PtRu nanoalloys as electrocatalysts with substantially enhanced activity and durability for direct methanol fuel cells.     

Engineering of a Low‐Cost,Highly Active,and Durable Tantalate–Graphene Hybrid Electrocatalyst for Oxygen Reduction

The oxygen reduction reaction (ORR) is one of the most important reactions in renewable energy conversion and storage devices. The full deployment of these devices depends on the development of highly active, stable, and low‐cost catalysts. Herein, a new hybrid material consisting of Na₂Ta₈O_21?x/Ta₂O₅/Ta₃N₅ nanocrystals grown on N‐doped reduced graphene oxide is reported. This catalyst shows a significantly enhanced ORR activity by ≈4 orders of magnitude in acidic media and by ≈2 orders of magnitude in alkaline media compared to individual Na₂Ta₈O_21?x on graphene. Moreover, it has excellent stability in both acid and alkaline media. It also has much better methanol tolerance than the commercial Pt/C, which is relevant to methanol fuel cells. The high ORR activity arises not only from the synergistic effect among the three Ta phases, but also from the concomitant nitrogen doping of the reduced graphene oxide nanosheets. A correlation between ORR activity and nitrogen content is demonstrated. Deep insights into the mechanism of the synergistic effect among these three Ta‐based phases, which boosts the ORR's kinetics, are acquired by combining specific experiments and density functional theory calculations.     

Ultrathin High Surface Area Nickel Boride (NixB) Nanosheets as Highly Efficient Electrocatalyst for Oxygen Evolution

The overriding obstacle to mass production of hydrogen from water as the premium fuel for powering our planet is the frustratingly slow kinetics of the oxygen evolution reaction (OER). Additionally, inadequate understanding of the key barriers of the OER is a hindrance to insightful design of advanced OER catalysts. This study presents ultrathin amorphous high‐surface area nickel boride (Ni_x B) nanosheets as a low‐cost, very efficient and stable catalyst for the OER for electrochemical water splitting. The catalyst affords 10 mA cm^?2 at 0.38 V overpotential during OER in 1.0 m KOH, reducing to only 0.28 V at 20 mA cm^?2 when supported on nickel foam, which ranks it among the best reported nonprecious catalysts for oxygen evolution. Operando X‐ray absorption fine‐structure spectroscopy measurements reveal prevalence of NiOOH, as well as Ni‐B under OER conditions, owing to a Ni‐B core@nickel oxyhydroxide shell (Ni‐B@NiO_x H) structure, and increase in disorder of the NiO_x H layer, thus revealing important insight into the transient states of the catalyst during oxygen evolution.     

Tailored Electron Transfer Pathways in Aucore/Ptshell–Graphene Nanocatalysts for Fuel Cells

Au_core/Pt_shell–graphene catalysts (G‐Cys‐Au@Pt) are prepared through chemical and surface chemical reactions. Au–Pt core–shell nanoparticles (Au@Pt NPs) covalently immobilized on graphene (G) are efficient electrocatalysts in low‐temperature polymer electrolyte membrane fuel cells. The 9.5 ± 2 nm Au@Pt NPs with atomically thin Pt shells are attached on graphene via l ‐cysteine (Cys), which serves as linkers controlling NP loading and dispersion, enhancing the Au@Pt NP stability, and facilitating interfacial electron transfer. The increased activity of G‐Cys‐Au@Pt, compared to non‐chemically immobilized G‐Au@Pt and commercial platinum NPs catalyst (C‐Pt), is a result of (1) the tailored electron transfer pathways of covalent bonds integrating Au@Pt NPs into the graphene framework, and (2) synergetic electronic effects of atomically thin Pt shells on Au cores. Enhanced electrocatalytic oxidation of formic acid, methanol, and ethanol is observed as higher specific currents and increased stability of G‐Cys‐Au@Pt compared to G‐Au@Pt and C–Pt. Oxygen reduction on G‐Cys‐Au@Pt occurs at 25 mV lower potential and 43 A g_Pt^?1 higher current (at 0.9 V vs reversible hydrogen electrode) than for C–Pt. Functional tests in direct fomic acid, methanol and ethanol fuel cells exhibit 95%, 53%, and 107% increased power densities for G‐Cys‐Au@Pt over C–Pt, respectively.     

Atomically Dispersed Fe‐Nx/C Electrocatalyst Boosts Oxygen Catalysis via a New Metal‐Organic Polymer Supramolecule Strategy

The development of high‐performance oxygen reduction reaction (ORR) catalysts derived from non‐Pt group metals (non‐PGMs) is urgent for the wide applications of proton exchange membrane fuel cells (PEMFCs). In this work, a facile and cost‐efficient supramolecular route is developed for making non‐PGM ORR catalyst with atomically dispersed Fe‐N_x/C sites through pyrolyzing the metal‐organic polymer coordinative hydrogel formed between Fe³⁺ and α‐L‐guluronate blocks of sodium alginate (SA). High‐angle annular dark field scanning transmission electron microscopy (HAADF‐STEM) and X‐ray absorption spectroscopy (XAS) verify that Fe atoms achieve atomic‐level dispersion on the obtained SA‐Fe‐N nanosheets and a possible fourfold coordination with N atoms. The best‐performing SA‐Fe‐N catalyst exhibits excellent ORR activity with half‐wave potential (E_1/2) of 0.812 and 0.910 V versus the reversible hydrogen electrode (RHE) in 0.5 m H₂SO₄ and 0.1 m KOH, respectively, along with respectable durability. Such performance surpasses that of most reported non‐PGM ORR catalysts. Density functional theory calculations suggest that the relieved passivation effect of OH* on Fe‐N₄/C structure leads to its superior ORR activity to Pt/C in alkaline solution. The work demonstrates a novel strategy for developing high‐performance non‐PGM ORR electrocatalysts with atomically dispersed and stable M‐N_x coordination sites in both acidic and alkaline media.     

Engineering Multimetallic Aerogels for pH‐Universal HER and ORR Electrocatalysis

The advent of noble metal aerogels (NMAs), that feature the high catalytic activity of noble metals and unique structural attributes of aerogels, has stimulated research on a new class of outstanding electrocatalysts. However, limited by the available compositions, the explored electrocatalytic reactions on NMAs are highly restricted and certain important electrochemical processes have not been investigated. Here, an effective gelation approach is demonstrated by using a strong salting‐out agent (i.e., NH₄F), thereby expanding the composition of NMAs to various multimetallic systems and providing a platform to investigate composition‐dependent electrocatalytic performance of NMAs. Combining structural features of aerogels and optimized chemical compositions, the Au–Pt and Au–Rh aerogel catalysts manifest remarkable pH‐universal (pH = 0–14) performance surpassing commercial Pt/C and many other nanoparticle (NP)‐based catalysts in the electrocatalytic oxygen reduction reaction, hydrogen evolution reaction, and water splitting, displaying enormous potential for the electrochemical hydrogen production, fuel cells, etc.     

The composition effect for the thermal properties of PdnAg(42-n)Pt13 ternary nanoalloys: a molecular dynamics study

In this study, the classical molecular dynamics simulations in canonical ensemble conditions (NVT) were used to investigate the dynamical properties of trimetallic Pd–Pt–Ag nanoalloy clusters with the interatomic interactions modelled by the Gupta many-body potential. The optimisations for best homotops were performed using the basin-hopping algorithm for 55 atom icosahedral Pd_nAg_(42-n)Pt₁₃ trimetallic clusters. We performed optimisations to search the best chemical ordering of icosahedron structure not allowing any geometric changes. The icosahedron structures which are the best homotops have a core-shell segregation. The obtained icosahedral structures with best homotops were taken as the initial configurations for MD simulations. The temperature ranges were explored which the surface sites of the clusters stay thermally stable. We estimated the melting temperatures of Pd_nAg_(42-n)Pt₁₃ trimetallic clusters using caloric curves and Lindemann parameters. No simple correlation between alloy composition and melting temperatures was determined. The Pd₃₅Ag₇Pt₁₃ composition has the highest melting temperature, however, the Pd₂₁Ag₂₁Pt₁₃ is the most stable composition according to the relative stability investigation. The simulation results showed that the melting of all Pd_nAg_(42-n)Pt₁₃ clusters takes place as a whole without any surface premelting.     

Highly Efficient and Durable Pd Hydride Nanocubes Embedded in 2D Amorphous NiB Nanosheets for Oxygen Reduction Reaction

A highly efficient and durable electrocatalyst of Pd hydride nanocubes encapsulated within 2D amorphous Ni‐B nanosheets is reported. The PdH_0.43 nanocubes are first synthesized via a simple N ,N ‐dimethylformamide thermal treatment. The as‐synthesized PdH_0.43 nanocubes are then encapsulated in 2D amorphous NiB nanosheets by NaBH₄ reduction in the presence of nickel species. During the NaBH₄ treatment, the PdH_0.43 can be further transformed into PdH_0.706 due to the presence of endogenous H₂. Electrochemical studies demonstrate that the degree of hydride of Pd nanocubes (PdH_x ) plays an important role in the enhancement of their oxygen reduction reaction (ORR) activity. With increasing x value, both the activity and stability increase significantly. At 0.90 V versus reversible hydrogen electrode, the ORR activity of PdH_0.706 @Ni‐B reaches 1.05 A mg_Pd^?1, which is nearly five times higher than that of the state‐of‐the‐art Pt catalysts. Accelerated durability tests show that even after 10 000 potential cycles, there is negligible shift in their half‐wave potential and no shape and structure change occurs, indicating the incorporation of amorphous 2D Ni‐B nanosheets can greatly improve their stability without compromising their activity. The present study illustrates the importance of high degree of hydride and presence of amorphous Ni‐B nanosheets on the enhancement of ORR activity for Pd‐based electrocatalyst.     

Triptan partition in model membranes

The development of fuel cells as clean-energy technologies is largely limited by the prohibitive cost of the noble-metal catalysts needed for catalyzing the oxygen reduction reaction (ORR) in fuel cells. A fundamental understanding of catalyst design principle that links material structures to the catalytic activity can accelerate the search for highly active and abundant bimetallic catalysts to replace platinum. Here, we present a first-principles study of ORR on Ag₁₂Cu cluster in alkaline environment. The adsorptions of O₂, OOH, and OH on Cu-doped Ag₁₃ are stronger than on Ag₁₃. The d-band centers of adsorption sites show the Cu-doping makes d-electrons transferred to higher energy state, and improves O₂ dissociation. ORR processes on Ag₁₂Cu and Ag₁₃ indicate Cu-doping can strongly promote ORR, and ORR process can be better preformed on Ag₁₂Cu than on Ag₁₃. For four-electron transfer, the effective reversible potential is 0.401 V/RHE on Ag₁₂Cu in alkaline medium.     

Electronic and Defective Engineering of Electrospun CaMnO3 Nanotubes for Enhanced Oxygen Electrocatalysis in Rechargeable Zinc–Air Batteries

Rational design and massive production of bifunctional catalysts with superior oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) activities are essential for developing metal–air batteries and fuel cells. Herein, controllable large‐scale synthesis of sulfur‐doped CaMnO₃ nanotubes is demonstrated via an electrospinning technique followed by calcination and sulfurization treatment. The sulfur doping can not only replace oxygen atoms to increase intrinsic electrical conductivity but also introduce abundant oxygen vacancies to provide enough catalytically active sites, which is further demonstrated by density functional theory calculation. The resulting sulfur‐modified CaMnO₃ (CMO/S) exhibits better electrocatalytic activity for ORR and OER in alkaline solution with higher stability performance than the pristine CMO. These results highlight the importance of sulfur treatment as a facile yet effective strategy to improve the ORR and OER catalytic activity of the pristine CaMnO₃. As a proof‐of‐concept, a rechargeable Zn–air battery using the bifunctional catalyst exhibits a small charge–discharge voltage polarization, and long cycling life. Furthermore, a solid‐state flexible and rechargeable Zn–air battery gives superior discharge–charge performance and remarkable stability. Therefore, the CMO/S nanotubes might be a promising replacement to the Pt‐based electrocatalysts for metal–air batteries and fuel cells.     

Efficiently Enhancing Oxygen Reduction Electrocatalytic Activity of MnO2 Using Facile Hydrogenation

Improving the electrocatalytic oxygen reduction reaction (ORR) activity of transition metal oxides is important for the development of non‐noble metal catalysts that are used in metal‐air batteries and fuel cells. Here, a novel facile strategy of hydrogenation to significantly enhance the ORR performance of MnO₂. The hydrogenated MnO₂ (H‐MnO₂), which is prepared through a simple heat treatment in hydrogen gas, shows characteristics of modified lattice/surface structures and increased electrical conductivity. In 0.1 M KOH aqueous solution, the prepared H‐MnO₂ exhibits high activity toward the oxygen electrocatalysis with more positive onset potential (≈60 mV), ≈14% larger of limiting current, lower yield of peroxide species, and better durability than the pristine oxide. Further conductivity testing and density functional theory (DFT) studies reveal the faster kinetics of ORR after hydrogenation is due to the formation of hydrogen bonds and altered microstructure and improved electronic properties. These results highlight the importance of hydrogenation as a facile yet effective strategy to improve the catalytic activity of transition metal oxides for ORR‐based applications.