Enabling High‐Energy Solid‐State Batteries with Stable Anode Interphase by the Use of Columnar Silicon Anodes

All‐solid‐state batteries (ASSBs) with silicon anodes are promising candidates to overcome energy limitations of conventional lithium‐ion batteries. However, silicon undergoes severe volume changes during cycling leading to rapid degradation. In this study, a columnar silicon anode (col‐Si) fabricated by a scalable physical vapor deposition process (PVD) is integrated in all‐solid‐state batteries based on argyrodite‐type electrolyte (Li₆PS₅Cl, 3 mS cm^?1) and Ni‐rich layered oxide cathodes (LiNi_0.9Co_0.05Mn_0.05O₂, NCM) with a high specific capacity (210 mAh g^?1). The column structure exhibits a 1D breathing mechanism similar to lithium, which preserves the interface toward the electrolyte. Stable cycling is demonstrated for more than 100 cycles with a high coulombic efficiency (CE) of 99.7–99.9% in full cells with industrially relevant areal loadings of 3.5 mAh cm^?2, which is the highest value reported so far for ASSB full cells with silicon anodes. Impedance spectroscopy revealed that anode resistance is drastically reduced after first lithiation, which allows high charging currents of 0.9 mA cm^?2 at room temperature without the occurrence of dendrites and short circuits. Finally, in‐operando monitoring of pouch cells gave valuable insights into the breathing behavior of the solid‐state cell.     

Slurry‐Fabricable Li+‐Conductive Polymeric Binders for Practical All‐Solid‐State Lithium‐Ion Batteries Enabled by Solvate Ionic Liquids

For mass production of all‐solid‐state lithium‐ion batteries (ASLBs) employing highly Li⁺ conductive and mechanically sinterable sulfide solid electrolytes (SEs), the wet‐slurry process is imperative. Unfortunately, the poor chemical stability of sulfide SEs severely restrict available candidates for solvents and in turn polymeric binders. Moreover, the binders interrupt Li⁺‐ionic contacts at interfaces, resulting in the below par electrochemical performance. In this work, a new scalable slurry fabrication protocol for sheet‐type ASLB electrodes made of Li⁺‐conductive polymeric binders is reported. The use of intermediate‐polarity solvent (e.g., dibromomethane) for the slurry allows for accommodating Li₆PS₅Cl and solvate‐ionic‐liquid‐based polymeric binders (NBR‐Li(G3)TFSI, NBR: nitrile?butadiene rubber, G3: triethylene glycol dimethyl ether, LiTFSI: lithium bis(trifluoromethanesulfonyl)imide) together without suffering from undesirable side reactions or phase separation. The LiNi_0.6Co_0.2Mn_0.2O₂ and Li₄Ti₅O₁₂ electrodes employing NBR‐Li(G3)TFSI show high capacities of 174 and 160 mA h g^?1 at 30 °C, respectively, which are far superior to those using conventional NBR (144 and 76 mA h g^?1). Moreover, high areal capacity of 7.4 mA h cm^?2 is highlighted for the LiNi_0.7Co_0.15Mn_0.15O₂ electrodes with ultrahigh mass loading of 45 mg cm^?2. The facilitated Li⁺‐ionic contacts at interfaces paved by NBR‐Li(G3)TFSI are evidenced by the complementary analysis from electrochemical and ⁷Li nuclear magnetic resonance measurements.     

Boosting Superior Lithium Storage Performance of Alloy‐Based Anode Materials via Ultraconformal Sb Coating–Derived Favorable Solid‐Electrolyte Interphase

Alloy materials such as Si and Ge are attractive as high‐capacity anodes for rechargeable batteries, but such anodes undergo severe capacity degradation during discharge–charge processes. Compared to the over‐emphasized efforts on the electrode structure design to mitigate the volume changes, understanding and engineering of the solid‐electrolyte interphase (SEI) are significantly lacking. This work demonstrates that modifying the surface of alloy‐based anode materials by building an ultraconformal layer of Sb can significantly enhance their structural and interfacial stability during cycling. Combined experimental and theoretical studies consistently reveal that the ultraconformal Sb layer is dynamically converted to Li₃Sb during cycling, which can selectively adsorb and catalytically decompose electrolyte additives to form a robust, thin, and dense LiF‐dominated SEI, and simultaneously restrain the decomposition of electrolyte solvents. Hence, the Sb‐coated porous Ge electrode delivers much higher initial Coulombic efficiency of 85% and higher reversible capacity of 1046 mAh g^?1 after 200 cycles at 500 mA g^?1, compared to only 72% and 170 mAh g^?1 for bare porous Ge. The present finding has indicated that tailoring surface structures of electrode materials is an appealing approach to construct a robust SEI and achieve long‐term cycling stability for alloy‐based anode materials.     

Solid‐State Prelithiation Enables High‐Performance Li‐Al‐H Anode for Solid‐State Batteries

Lithium alanates exhibit high theoretical specific capacities and appropriate lithiation/delithiation potentials, but suffer from poor reversibility, cycling stability, and rate capability due to their sluggish kinetics and extensive side reactions. Herein, a novel and facile solid‐state prelithiation approach is proposed to in situ prepare a Li₃AlH₆‐Al nanocomposite from a short‐circuited electrochemical reaction between LiAlH₄ and Li with the help of fast electron and Li‐ion conductors (C and P6₃mc LiBH₄). This nanocomposite consists of dispersive Al nanograins and an amorphous Li₃AlH₆ matrix, which enables superior electrochemical performance in solid‐state cells, as much higher specific capacity (2266 mAh g^?1), Coulombic efficiency (88%), cycling stability (71% retention in the 100th cycle), and rate capability (1429 mAh g^?1 at 1 A g^?1) are achieved. In addition, this nanocomposite works well in the solid‐state full cell with LiCoO₂ cathode, demonstrating its promising application prospects. Mechanism analysis reveals that the dispersive Al nanograins and amorphous Li₃AlH₆ matrix can dramatically enhance the lithiation and delithiation kinetics without side reactions, which is mainly responsible for the excellent overall performance. Moreover, this solid‐state prelithiation approach is general and can also be applied to other Li‐poor electrode materials for further modification of their electrochemical behavior.     

Interface‐Engineered All‐Solid‐State Li‐Ion Batteries Based on Garnet‐Type Fast Li+ Conductors

All‐solid‐state Li‐ion batteries based on Li₇La₃Zr₂O₁₂ (LLZO) garnet structures require novel electrode assembly strategies to guarantee a proper Li⁺ transfer at the electrode–electrolyte interfaces. Here, first stable cell performances are reported for Li‐garnet, c‐Li_6.25Al_0.25La₃Zr₂O₁₂, all‐solid‐state batteries running safely with a full ceramics setup, exemplified with the anode material Li₄Ti₅O₁₂. Novel strategies to design an enhanced Li⁺ transfer at the electrode–electrolyte interface using an interface‐engineered all‐solid‐state battery cell based on a porous garnet electrolyte interface structure, in which the electrode material is intimately embedded, are presented. The results presented here show for the first time that all‐solid‐state Li‐ion batteries with LLZO electrolytes can be reversibly charge–discharge cycled also in the low potential ranges (≈1.5 V) for combinations with a ceramic anode material. Through a model experiment, the interface between the electrode and electrolyte constituents is systematically modified revealing that the interface engineering helps to improve delivered capacities and cycling properties of the all‐solid‐state Li‐ion batteries based on garnet‐type cubic LLZO structures.     

Rational Design of Hierarchical “Ceramic‐in‐Polymer” and “Polymer‐in‐Ceramic” Electrolytes for Dendrite‐Free Solid‐State Batteries

Solid polymer electrolytes as one of the promising solid‐state electrolytes have received extensive attention due to their excellent flexibility. However, the issues of lithium (Li) dendrite growth still hinder their practical applications in solid‐state batteries (SSBs). Herein, composite electrolytes from “ceramic‐in‐polymer” (CIP) to “polymer‐in‐ceramic” (PIC) with different sizes of garnet particles are investigated for their effectiveness in dendrite suppression. While the CIP electrolyte with 20 vol% 200 nm Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) particles (CIP‐200 nm) exhibits the highest ionic conductivity of 1.6 × 10^?4 S cm^?1 at 30 °C and excellent flexibility, the PIC electrolyte with 80 vol% 5 µm LLZTO (PIC‐5 µm) shows the highest tensile strength of 12.7 MPa. A sandwich‐type composite electrolyte (SCE) with hierarchical garnet particles (a PIC‐5 µm interlayer sandwiched between two CIP‐200 nm thin layers) is constructed to simultaneously achieve dendrite suppression and excellent interfacial contact with Li metal. The SCE enables highly stable Li plating/stripping cycling for over 400 h at 0.2 mA cm^?2 at 30 °C. The LiFePO₄/SCE/Li cells also demonstrate excellent cycle performance at room temperature. Fabricating sandwich‐type composite electrolytes with hierarchical filler designs can be an effective strategy to achieve dendrite‐free SSBs with high performance and high safety at room temperature.     

Low‐Cost Hollow Mesoporous Polymer Spheres and All‐Solid‐State Lithium,Sodium Batteries

A practical, low‐cost synthesis of hollow mesoporous organic polymer (HMOP) spheres is reported. The electrochemical properties of Li⁺/Na⁺‐electrolyte membranes with these spheres substituting for oxide filler particles in poly(ethylene oxide) (PEO)‐filler composite are explored. The electrolyte membranes are mechanically robust, thermally stable to over 250 °C, and block dendrites from a metallic‐lithium/sodium anode. The Li⁺/Na⁺ transfer impedance across the lithium/sodium–electrolyte interface is initially acceptable at 65 °C and scavenging of impurities by the porous‐spheres filler lowers this impedance relative to that with Al₂O₃. All‐solid‐state Li/LiFePO₄ and Na/NaTi₂(PO4)₃ cells give stable discharge capacity of ≈130 and 80 mAh g^?1, respectively, at 0.5 C and 65 °C for 100 cycles.     

A Lithium Amide‐Borohydride Solid‐State Electrolyte with Lithium‐Ion Conductivities Comparable to Liquid Electrolytes

High ionic conductivity of up to 6.4 × 10^?3 S cm^?1 near room temperature (40 °C) in lithium amide‐borohydrides is reported, comparable to values of liquid organic electrolytes commonly employed in lithium‐ion batteries. Density functional theory is applied coupled with X‐ray diffraction, calorimetry, and nuclear magnetic resonance experiments to shed light on the conduction mechanism. A Li₄Ti₅O₁₂ half‐cell battery incorporating the lithium amide‐borohydride electrolyte exhibits good rate performance up to 3.5 mA cm^?2 (5 C) and stable cycling over 400 cycles at 1 C at 40 °C, indicating high bulk and interfacial stability. The results demonstrate the potential of lithium amide‐borohydrides as solid‐state electrolytes for high‐power lithium‐ion batteries.     

Perovskite Membranes with Vertically Aligned Microchannels for All‐Solid‐State Lithium Batteries

Perovskite‐type solid‐state electrolytes exhibit great potential for the development of all‐solid‐state lithium batteries due to their high Li‐ion conductivity (approaching 10^?3 S cm^?1), wide potential window, and excellent thermal/chemical stability. However, the large solid–solid interfacial resistance between perovskite electrolytes and electrode materials is still a great challenge that hinders the development of high‐performance all‐solid‐state lithium batteries. In this work, a perovskite‐type Li_0.34La_0.51TiO₃ (LLTO) membrane with vertically aligned microchannels is constructed by a phase‐inversion method. The 3D vertically aligned microchannel framework membrane enables more effective Li‐ion transport between the cathode and solid‐state electrolyte than a planar LLTO membrane. A significant decrease in the perovskite/cathode interfacial resistance, from 853 to 133 Ω cm², is observed. It is also demonstrated that full cells utilizing LLTO with vertically aligned microchannels as the electrolyte exhibit a high specific capacity and improved rate performance.     

Solvent‐Free Synthesis of Thin,Flexible, Nonflammable Garnet‐Based Composite Solid Electrolyte for All‐Solid‐State Lithium Batteries

Thin solid‐state electrolytes with nonflammability, high ionic conductivity, low interfacial resistance, and good processability are urgently required for next‐generation safe, high energy density lithium metal batteries. Here, a 3D Li_6.75La₃Zr_1.75Ta_0.25O₁₂ (LLZTO) self‐supporting framework interconnected by polytetrafluoroethylene (PTFE) binder is prepared through a simple grinding method without any solvent. Subsequently, a garnet‐based composite electrolyte is achieved through filling the flexible 3D LLZTO framework with a succinonitrile solid electrolyte. Due to the high content of garnet ceramic (80.4 wt%) and high heat‐resistance of the PTFE binder, such a composite electrolyte film with nonflammability and high processability exhibits a wide electrochemical window of 4.8 V versus Li/Li⁺ and high ionic transference number of 0.53. The continuous Li⁺ transfer channels between interconnected LLZTO particles and succinonitrile, and the soft electrolyte/electrode interface jointly contribute to a high ambient‐temperature ionic conductivity of 1.2 × 10^?4 S cm^?1 and excellent long‐term stability of the Li symmetric battery (stable at a current density of 0.1 mA cm^?2 for over 500 h). Furthermore, as‐prepared LiFePO₄|Li and LiNi_0.5Mn_0.3Co_0.2O₂|Li batteries based on the thin composite electrolyte exhibit high discharge specific capacities of 153 and 158 mAh g^?1 respectively, and desirable cyclic stabilities at room temperature.     

High‐Capacity All‐Solid‐State Sodium Metal Battery with Hybrid Polymer Electrolytes

All‐solid‐state sodium metal batteries (SSMBs) are of great interest for their high theoretical capacity, nonflammability, and relatively low cost owing partially to the abundance of sodium recourses. However, it is challenging to fabricate SSMBs because compared with their counterparts, which contain lithium metal, sodium metal is mechanically softer and more reactive toward the electrolyte. Herein, the synthesis and electrochemical properties of newly designed sodium‐containing hybrid network solid polymer electrolytes (SPEs) and their application in SSMBs are reported. The hybrid network is synthesized by controlled crosslinking of octakis(3‐glycidyloxypropyldimethylsiloxy)octasilsesquioxane and amine‐terminated polyethylene glycol in existence with sodium perchlorate (NaClO₄). Plating and stripping experiments using symmetric cells show prolonged cycle life of the SPEs, >5150 and 3550 h at current density of 0.1 and 0.5 mA cm^?2, respectively. The results for the first time show that the SPE|sodium metal interface migrates into the SPE phase upon cycling. SSMBs fabricated with the hybrid SPE sandwiched between sodium metal anode and bilayered δ‐Na_xV₂O₅ cathode exhibit record‐high specific capacity for solid sodium‐ion batteries of 305 mAh g^?1 and excellent Coulombic efficiency. This work demonstrates that the hybrid network SPEs are promising for SSMB applications.     

The Role of Interlayer Chemistry in Li‐Metal Growth through a Garnet‐Type Solid Electrolyte

Securing the chemical and physical stabilities of electrode/solid‐electrolyte interfaces is crucial for the use of solid electrolytes in all‐solid‐state batteries. Directly probing these interfaces during electrochemical reactions would significantly enrich the mechanistic understanding and inspire potential solutions for their regulation. Herein, the electrochemistry of the lithium/Li₇La₃Zr₂O₁₂‐electrolyte interface is elucidated by probing lithium deposition through the electrolyte in an anode‐free solid‐state battery in real time. Lithium plating is strongly affected by the geometry of the garnet‐type Li₇La₃Zr₂O₁₂ (LLZO) surface, where nonuniform/filamentary growth is triggered particularly at morphological defects. More importantly, lithium‐growth behavior significantly changes when the LLZO surface is modified with an artificial interlayer to produce regulated lithium depositions. It is shown that lithium‐growth kinetics critically depend on the nature of the interlayer species, leading to distinct lithium‐deposition morphologies. Subsequently, the dynamic role of the interlayer in battery operation is discussed as a buffer and seed layer for lithium redistribution and precipitation, respectively, in tailoring lithium deposition. These findings broaden the understanding of the electrochemical lithium‐plating process at the solid‐electrolyte/lithium interface, highlight the importance of exploring various interlayers as a new avenue for regulating the lithium‐metal anode, and also offer insight into the nature of lithium growth in anode‐free solid‐state batteries.     

Facilitating Interfacial Stability Via Bilayer Heterostructure Solid Electrolyte Toward High‐energy,Safe and Adaptable Lithium Batteries

Solid‐state electrolytes are widely anticipated to enable the revival of high energy density and safe metallic Li batteries, however, their lower ionic conductivity at room temperature, stiff interfacial contact, and severe polarization during cycling continue to pose challenges in practical applications. Herein, a dual‐composite concept is applied to the design of a bilayer heterostructure solid electrolyte composed of Li⁺ conductive garnet nanowires (Li_6.75La₃Zr_1.75Nb_0.25O₁₂)/polyvinylidene fluoride‐co‐hexafluoropropylene (PVDF‐HFP) as a tough matrix and modified metal organic framework particles/polyethylene oxide/PVDF‐HFP as an interfacial gel. The integral ionic conductivity of the solid electrolyte reaches 2.0 × 10^?4 S cm^?1 at room temperature. In addition, a chemically/electrochemically stable interface is rapidly formed, and Li dendrites are well restrained by a robust inorganic shield and matrix. As a result, steady Li plating/stripping for more than 1700 h at 0.25 mA cm^?2 is achieved. Solid‐state batteries using this bilayer heterostructure solid electrolyte deliver promising battery performance (efficient capacity output and cycling stability) at ambient temperature (25 °C). Moreover, the pouch cells exhibit considerable flexibility in service and unexpected endurance under a series of extreme abuse tests including hitting with a nail, burning, immersion under water, and freezing in liquid nitrogen.     

Correlating Macro and Atomic Structure with Elastic Properties and Ionic Transport of Glassy Li2S‐P2S5 (LPS) Solid Electrolyte for Solid‐State Li Metal Batteries

A combination of high ionic conductivity and facile processing suggest that sulfide‐based materials are promising solid electrolytes that have the potential to enable Li metal batteries. Although the Li₂S‐P₂S₅ (LPS) family of compounds exhibit desirable characteristics, it is known that Li metal preferentially propagates through microstructural defects, such as particle boundaries and/or pores. Herein, it is demonstrated that a near theoretical density (98% relative density) LPS 75‐25 glassy electrolyte exhibiting high ionic conductivity can be achieved by optimizing the molding pressure and temperature. The optimal molding pressure reduces porosity and particle boundaries while preserving the preferred amorphous structure. Moreover, molecular rearrangements and favorable Li coordination environments for conduction are attained. Consequently, the Young's Modulus approximately doubles (30 GPa) and the ionic conductivity increases by a factor of five (1.1 mS cm^?1) compared to conventional room temperature molding conditions. It is believed that this study can provide mechanistic insight into processing‐structure‐property relationships that can be used as a guide to tune microstructural defects/properties that have been identified to have an effect on the maximum charging current that a solid electrolyte can withstand during cycling without short‐circuiting.     

The Fast Charge Transfer Kinetics of the Lithium Metal Anode on the Garnet‐Type Solid Electrolyte Li6.25Al0.25La3Zr2O12

The charge transfer kinetics between a lithium metal electrode and an inorganic solid electrolyte is of key interest to assess the rate capability of future lithium metal solid state batteries. In an in situ microelectrode study run in a scanning electron microscope, it is demonstrated that—contrary to the prevailing opinion—the intrinsic charge transfer resistance of the Li|Li_6.25Al_0.25La₃Zr₂O₁₂ (LLZO) interface is in the order of 10^?1 Ω cm² and thus negligibly small. The corresponding high exchange current density in combination with the single ion transport mechanism (t⁺ ≈ 1) of the inorganic solid electrolyte enables extremely fast plating kinetics without the occurrence of transport limitations. Local plating rates in the range of several A cm^?2 are demonstrated at defect free and chemically clean Li|LLZO interfaces. Practically achievable current densities are limited by lateral growth of lithium along the surface as well as electro‐chemo‐mechanical‐induced fracture of the solid electrolyte. In combination with the lithium vacancy diffusion limitation during electrodissolution, these morphological instabilities are identified as the key fundamental limitations of the lithium metal electrode for solid‐state batteries with inorganic solid electrolytes.     

Conductive and Catalytic Triple‐Phase Interfaces Enabling Uniform Nucleation in High‐Rate Lithium–Sulfur Batteries

Rechargeable lithium–sulfur batteries have attracted tremendous scientific attention owing to their superior energy density. However, the sulfur electrochemistry involves multielectron redox reactions and complicated phase transformations, while the final morphology of solid‐phase Li₂S precipitates largely dominate the battery's performance. Herein, a triple‐phase interface among electrolyte/CoSe₂/G is proposed to afford strong chemisorption, high electrical conductivity, and superb electrocatalysis of polysulfide redox reactions in a working lithium–sulfur battery. The triple‐phase interface effectively enhances the kinetic behaviors of soluble lithium polysulfides and regulates the uniform nucleation and controllable growth of solid Li₂S precipitates at large current density. Therefore, the cell with the CoSe₂/G functional separator delivers an ultrahigh rate cycle at 6.0 C with an initial capacity of 916 mAh g^?1 and a capacity retention of 459 mAh g^?1 after 500 cycles, and a stable operation of high sulfur loading electrode (2.69–4.35 mg cm^?2). This work opens up a new insight into the energy chemistry at interfaces to rationally regulate the electrochemical redox reactions, and also inspires the exploration of related energy storage and conversion systems based on multielectron redox reactions.     

Polysulfide‐Shuttle Control in Lithium‐Sulfur Batteries with a Chemically/Electrochemically Compatible NaSICON‐Type Solid Electrolyte

A NaSICON‐type Li⁺‐ion conductive membrane with a formula of Li_{1+ x} Y _x Zr_{2? x} (PO₄)₃ (LYZP) (x = 0–0.15) has been explored as a solid‐electrolyte/separator to suppress polysulfide‐crossover in lithium‐sulfur (Li‐S) batteries. The LYZP membrane with a reasonable Li⁺‐ion conductivity shows both favorable chemical compatibility with the lithium polysulfide species and exhibits good electrochemical stability under the operating conditions of the Li‐S batteries. Through an integration of the LYZP solid electrolyte with the liquid electrolyte, the hybrid Li‐S batteries show greatly enhanced cyclability in contrast to the conventional Li‐S batteries with the porous polymer (e.g., Celgard) separator. At a rate of C/5, the hybrid Li ||LYZP|| Li₂S₆ batteries developed in this study (with a Li‐metal anode, a liquid/LYZP hybrid electrolyte, and a dissolved lithium polysulfide cathode) delivers an initial discharge capacity of ≈1000 mA h g^?1 (based on the active sulfur material) and retains ≈90% of the initial capacity after 150 cycles with a low capacity fade‐rate of <0.07% per cycle.     

High Capacity All‐Solid‐State Lithium Batteries Enabled by Pyrite‐Sulfur Composites

As the theoretical limit of intercalation material‐based lithium‐ion batteries is approached, alternative chemistries based on conversion reactions are presently considered. The conversion of sulfur is particularly appealing as it is associated with a theoretical gravimetric energy density up to 2510 Wh kg^?1. In this paper, three different carbon‐iron disulfide‐sulfur (C‐FeS₂‐S) composites are proposed as alternative positive electrode materials for all‐solid‐state lithium‐sulfur batteries. These are synthesized through a facile, low‐cost, single‐step ball‐milling procedure. It is found that the crystalline structure (evaluated by X‐ray diffraction) and the morphology of the composites (evaluated by scanning electron microscopy) are greatly influenced by the FeS₂:S ratio. Li/LiI‐Li₃PS₄/C‐FeS₂‐S solid‐state cells are tested under galvanostatic conditions, while differential capacity plots are used to discuss the peculiar electrochemical features of these novel materials. These cells deliver capacities as high as 1200 mAh g_(FeS2+S)^?1 at the intermediate loading of 1 mg cm^?2 (1.2 mAh cm^?2), and up to 3.55 mAh cm^?2 for active material loadings as high as 5 mg cm^?2 at 20 °C. Such an excellent performance, rarely reported for (sulfur/metal sulfide)‐based, all solid‐state cells, makes these composites highly promising for real application where high positive electrode loadings are required.     

Unraveling the Dual Functionality of High‐Donor‐Number Anion in Lean‐Electrolyte Lithium‐Sulfur Batteries

Minimizing electrolyte use is essential to achieve high practical energy density of lithium–sulfur (Li–S) batteries. However, the sulfur cathode is more readily passivated under a lean electrolyte condition, resulting in low sulfur utilization. In addition, continuous electrolyte decomposition on the Li metal anode aggravates the problem, provoking rapid capacity decay. In this work, the dual functionalities of NO₃^? as a high‐donor‐number (DN) salt anion is presented, which improves the sulfur utilization and cycling stability of lean‐electrolyte Li–S batteries. The NO₃^? anion elevates the solubility of the sulfur species based on its high electron donating ability, achieving a high sulfur utilization of above 1200 mA h g^?1. Furthermore, the anion suppresses electrolyte decomposition on the Li metal by regulating the lithium ion (Li⁺) solvation sheath, enhancing the cycle performance of the lean electrolyte cell. By understanding the anionic effects, this work demonstrates the potential of the high‐DN electrolyte, which is beneficial for both the cathode and anode of Li–S batteries.     

MoN Supported on Graphene as a Bifunctional Interlayer for Advanced Li‐S Batteries

Rational design of effective polysulfide barriers is highly important for high‐performance lithium‐sulfur (Li‐S) batteries. A variety of adsorbents have been applied as interlayers to alleviate the shuttle effect. Nevertheless, the unsuccessful oxidation of Li₂S on interlayers leads to loss of active materials and blocks Li ion transport. In this work, a MoN‐based interlayer sandwiched between the C‐S cathode and the separator is developed. Such an interlayer not only strongly binds lithium polysulfides via Mo‐S bonding but also efficiently accelerates the decomposition of Li₂S. The acceleration mechanism toward Li₂S decomposition is determined to be a combination of contributions of catalytic cleavage of Li‐S bond in Li₂S based on the proposed covalence‐activation mechanism and rapid migration of the produced Li ions. As a result, the C–S cathodes with the as‐developed interlayer manifest a negligible charging potential barrier and outstanding cycling stability with a very low capacity fading rate of 0.023% per cycle during 1500 cycles at 1 C. High areal capacity of 6.02 mAh cm^?2 is achieved for high sulfur loading of 7.0 mg cm^?2 after cycling at 0.1 C. The material and strategy demonstrated in this work can open the door toward developing shuttle suppression interlayers without impairing cathode performance.