Selection and characterization of a nickel-tolerant cell line from tobacco (Nicotiana tabacum cv. bright yellow-2) suspension culture

To investigate the cellular/molecular mechanisms of nickel (Ni) tolerance in high-biomass-producing plants, we selected a Ni-tolerant (NIT) cell line from tobacco ( Nicotiana tabacum L. cv. bright yellow-2) suspension culture. Examination of response to various abiotic stresses showed that the NIT cells acquired remarkable tolerance to excess Ni, Cu, and Al but not to the other stresses. That the NIT cells accumulated approximately 2 m M Ni under the 700 µ M Ni condition suggests that the NIT cells can hyperaccumulate Ni and possess internal detoxification mechanisms for Ni. Two different sizes of putative β- d -xylosidase were constitutively secreted by the NIT cells, and the NIT cells showed greater elongation than the wild-type (WT) cells. Oxalate, citrate, 2-oxoglutarate, and glutamate contents were constitutively two- or three-fold higher in the NIT cells than in the WT cells, and histidine content was increased by up to three-fold in the NIT cells exposed to 700 µ M Ni compared to those in the WT cells. Newport green DCF diacetate (NPG), a Ni-specific fluorescence indicator, enabled the visualization of the subcellular localization of Ni in both WT and NIT cells. The NPG fluorescence was localized mainly in the vacuoles regardless of the WT or NIT cells under excess Ni conditions. The transport of Ni-organic acids and/or Ni-histidine complex into the vacuoles might be an important mechanism contributing to the high Ni tolerance of and the hyperaccumulation of Ni by the NIT cells.     

Optimization of Carbon‐ and Binder‐Free Au Nanoparticle‐Coated Ni Nanowire Electrodes for Lithium‐Oxygen Batteries

A Au nanoparticle‐coated Ni nanowire substrate without binder or carbon is used as the electrode (denoted as the Au/Ni electrode) for Li‐oxygen (Li‐O₂) batteries. A minimal amount of Au nanoparticles with sizes of <30 nm on a Ni nanowire substrate are coated using a simple electrodeposition method to the extent that maximum capacity can be utilized. This optimized, one body, Au/Ni electrode shows high capacities of 921 mAh g^?1_Au, 591 mAh g^?1_Au, and 359 mAh g^?1_Au, which are obtained at currents of 300 mAg^?1_Au, 500 mAg^?1_Au, and 1000 mAg^?1_Au respectively. More importantly, the Au/Ni electrode exhibits excellent cycle stability over 200 cycles.     

Direct Growth of Flower‐Like δ‐MnO2 on Three‐Dimensional Graphene for High‐Performance Rechargeable Li‐O2 Batteries

A challenge still remains to develop high‐performance and cost‐effective air electrode for Li‐O₂ batteries with high capacity, enhanced rate capability and long cycle life (100 times or above) despite recent advances in this field. In this work, a new design of binder‐free air electrode composed of three‐dimensional (3D) graphene (G) and flower‐like δ‐MnO₂ (3D‐G‐MnO₂) has been proposed. In this design, graphene and δ‐MnO₂ grow directly on the skeleton of Ni foam that inherits the interconnected 3D scaffold of Ni foam. Li‐O₂ batteries with 3D‐G‐MnO₂ electrode can yield a high discharge capacity of 3660 mAh g^?1 at 0.083 mA cm^?2. The battery can sustain 132 cycles at a capacity of 492 mAh g^?1 (1000 mAh g_carbon ^?1) with low overpotentials under a high current density of 0.333 mA cm^?2. A high average energy density of 1350 Wh Kg^?1 is maintained over 110 cycles at this high current density. The excellent catalytic activity of 3D‐G‐MnO₂ makes it an attractive air electrode for high‐performance Li‐O₂ batteries.     

Phase Transformation Induced Capacitance Activation for 3D Graphene‐CoO Nanorod Pseudocapacitor

Development of a pseudocapacitor over the integration of metal oxide on carbonaceous materials is a promising step towards energy storage devices with high energy and power densities. Here, a self‐assembled cobalt oxide (CoO) nanorod cluster on three‐dimensional graphene (CoO‐3DG) is synthesized through a facile hydrothermal method followed by heat treatment. As an additive‐free electrode, CoO‐3DG exhibits good electrochemical performance. Compared with CoO nanorod clusters grown on Ni foam (i.e., CoO‐Ni, ≈680 F g^?1 at 1 A g^?1 and ≈400 F g^?1 at 20 A g^?1), CoO‐3DG achieves much higher capacitance (i.e., ≈980 F g^?1 at 1 A g^?1 and ≈600 F g^?1 at 20 A g^?1) with excellent cycling stability of 103% retention of specific capacitance after 10 000 cycles. Furthermore, it shows an interesting activation process and instability with a redox reaction for CoO. In addition, the phase transformation from CoO nanorods to Co₃O₄ nanostructures was observed and investigated after charge and discharge process, which suggests the activation kinetics and the phase transformable nature of CoO based nanostructure. These observations demonstrate phase transformation with morphological change induced capacitance increasement in the emergent class of metal oxide materials for electrochemical energy storage device.     

Microtubule‐dependent changes in morphology and localization of chloride transport proteins in gill mitochondria‐rich cells of the tilapia,Oreochromis mossambicus

The tilapia (Oreochromis mossambicus) is a euryhaline fish exhibiting adaptive changes in cell size, phenotype, and ionoregulatory functions upon salinity challenge. Na⁺/Cl^? cotransporter (NCC) and Na⁺/K⁺/2Cl^? cotransporter (NKCC) are localized in the apical and basolateral membranes of mitochondria‐rich (MR) cells of the gills. These cells are responsible for chloride absorption (NCC) and secretion (NKCC), respectively, thus, the switch of gill NCC and NKCC expression is a crucial regulatory mechanism for salinity adaptation in tilapia. However, little is known about the interaction of cytoskeleton and these adaptive changes. In this study, we examined the time‐course of changes in the localization of NKCC/NCC in the gills of tilapia transferred from fresh water (FW) to brackish water (20‰) and from seawater (SW; 35‰) to FW. The results showed that basolateral NKCC disappeared and NCC was expressed in the apical membrane of MR cells. To further clarify the process of these adaptive changes, colchicine, a specific inhibitor of microtubule‐dependent cellular regulating processes was used. SW‐acclimated tilapia were transferred to SW, FW, and FW with colchicine (colchicine‐FW) for 96 h. Compared with the FW‐treatment group, in the MR cells of colchicine‐FW‐treatment group, (1) the average size was significantly larger, (2) only wavy‐convex‐subtype apical surfaces were found, and (3) the basolateral (cytoplasmic) NKCC signals were still exhibited. Taken together, our results suggest that changes in size, phenotype, as well as the expression of NCC and NKCC cotransporters of MR cells in the tilapia are microtubule‐dependent. J. Morphol. 277:1113–1122, 2016. © 2016 Wiley Periodicals, Inc.     

Light‐Dependent and Aeration‐Independent Gram‐Scale Hydroxylation of Cyclohexane to Cyclohexanol by CYP450 Harboring Synechocystis sp. PCC 6803

Oxygenase‐containing cyanobacteria constitute promising whole‐cell biocatalysts for oxyfunctionalization reactions. Photosynthetic water oxidation thereby delivers the required cosubstrates, that is activated reduction equivalents and O₂, sustainably. A recombinant Synechocystis sp. PCC 6803 strain showing unprecedentedly high photosynthesis‐driven oxyfunctionalization activities is developed, and its technical applicability is evaluated. The cells functionally synthesize a heterologous cytochrome P450 monooxygenase enabling cyclohexane hydroxylation. The biocatalyst‐specific reaction rate is found to be light‐dependent, reaching 26.3 ± 0.6 U g_CDW^?1 (U = μmol min^?1 and cell dry weight [CDW]) at a light intensity of 150 µmol_photons m^?2 s^?1. In situ substrate supply via a two‐liquid phase system increases the initial specific activity to 39.2 ± 0.7 U g_CDW^?1 and stabilizes the biotransformation by preventing cell toxification. This results in a tenfold increased specific product yield of 4.5 g_cyclohexanol g_CDW^?1 as compared to the single aqueous phase system. Subsequently, the biotransformation is scaled from a shake flask to a 3 L stirred‐tank photobioreactor setup. In situ O₂ generation via photosynthetic water oxidation allows a nonaerated process operation, thus circumventing substrate evaporation as the most critical factor limiting the process performance and stability. This study for the first time exemplifies the technical applicability of cyanobacteria for aeration‐independent light‐driven oxyfunctionalization reactions involving highly toxic and volatile substrates.     

Non‐symbiotic nitrogen fixation during leaf litter decomposition in an old‐growth temperate rain forest of Chiloé Island,southern Chile: Effects of single versus mixed species litter

Heterotrophic nitrogen fixation is a key ecosystem process in unpolluted, temperate old‐growth forests of southern South America as a source of new nitrogen to ecosystems. Decomposing leaf litter is an energy‐rich substrate that favours the occurrence of this energy demanding process. Following the niche ‘complementarity hypothesis’, we expected that decomposing leaf litter of a single tree species would support lower rates of non‐symbiotic N fixation than mixed species litter taken from the forest floor. To test this hypothesis we measured acetylene reduction activity in the decomposing monospecific litter of three evergreen tree species (litter C/N ratios, 50–79) in an old‐growth rain forest of Chiloé Island, southern Chile. Results showed a significant effect of species and month (anova , Tukey's test, P < 0.05) on decomposition and acetylene reduction rates (ARR), and a species effect on C/N ratios and initial % N of decomposing leaf litter. The lowest litter quality was that of Nothofagus nitida (C/N ratio = 78.7, lignin % = 59.27 ± 4.09), which resulted in higher rates of acetylene reduction activity (mean = 34.09 ± SE = 10.34 nmol h^?1 g^?1) and a higher decomposition rate (k = 0.47) than Podocarpus nubigena (C/N = 54.4, lignin % = 40.31 ± 6.86, Mean ARR = 4.11 ± 0.71 nmol h^?1 g^?1, k = 0.29), and Drimys winteri (C/N = 50.6, lignin % = 45.49 ± 6.28, ARR = 10.2 ± 4.01 nmol h^?1 g^?1, k = 0.29), and mixed species litter (C/N = 60.7, ARR = 8.89 ± 2.13 nmol h^?1g^?1). We interpret these results as follows: in N‐poor litter and high lignin content of leaves (e.g. N. nitida) free‐living N fixers would be at competitive advantage over non‐fixers, thereby becoming more active. Lower ARR in mixed litter can be a consequence of a lower litter C/N ratio compared with single species litter. We also found a strong coupling between in situ acetylene reduction and net N mineralization in surface soils, suggesting that as soon N is fixed by diazotroph bacteria it may be immediately incorporated into mineral soil by N mineralizers, thus reducing N immobilization.     

All‐Organic Battery Composed of Thianthrene‐ and TCAQ‐Based Polymers

An all‐organic battery consisting of two redox‐polymers, namely poly(2‐vinylthianthrene) and poly(2‐methacrylamide‐TCAQ) is assembled. This all‐organic battery shows excellent performance characteristics, namely flat discharge plateaus, an output voltage exceeding 1.3 V, and theoretical capacities of both electrodes higher than 100 mA h g^?1. Both organic electrode materials are synthesized in two respective three synthetic steps using the free‐radical polymerization technique. Li‐organic batteries manufactured from these polymers prove their suitability as organic electrode materials. The cathode material poly(2‐vinylthianthrene) (3) displays a discharging plateau at 3.95 V versus Li⁺/Li and a discharge capacity of 105 mA h g^?1, corresponding to a specific energy of about 415 mW h g^?1. The anode material poly(2‐methacrylamide‐TCAQ) (7) exhibits an initial discharge capacity of 130 mA h g^?1, corresponding to 94% material activity. The combination of both materials results in an all‐organic battery with a discharge voltage of 1.35 V and an initial discharge capacity of 105 mA h g^?1 (95% material activity).     

Hierarchically Porous N‐Doped Carbon Fibers as a Free‐Standing Anode for High‐Capacity Potassium‐Based Dual‐Ion Battery

Potassium‐based dual‐ion batteries (KDIBs) have emerged as a new generation of rechargeable batteries, due to their high cell voltage, low cost, and the natural abundance of potassium resources. However, the low capacity and poor cycling stability largely hinder the further development of KDIBs. Herein, the fabrication of hierarchically porous N‐doped carbon fibers (HPNCFs) as a free‐standing anode for high‐performance KDIBs is reported. With a free‐standing hierarchical structure (micro/meso/macropores and nanochannels) and high‐content of nitrogen doping, the HPNCFs not only provide intrinsic electron pathways and efficient ion transport channels, but also afford sufficient free space to tolerate the volume change during cycling. Consequently, the KDIBs made from a graphite cathode and an optimized HPNCFs anode deliver a high reversible capacity of 197 mAh g^?1 at a specific current of 50 mA g^?1, and excellent cycling stability (65 mAh g^?1 after 346 cycles at a specific current of 100 mA g^?1, the capacity calculation of the KDIBs is based on the mass of the anode). These results indicate that the properly designed HPNCFs can effectively improve the capacity and cycling stability of the KDIBs, indicating a great potential for applications in the field of high‐performance energy‐storage devices.     

In Situ Subangstrom‐Thick Organic Engineering Enables Mono‐scale,Ultrasmall ZnO Nanocrystals for a High Initial Coulombic Efficiency,Fully Reversible Conversion,and Cycle‐Stable Li‐Ion Storage

A solid electrolyte interphase (SEI)‐free surface and fully reversible conversion are simultaneously realized in the Li‐ion storage of a specially designed ZnO porous nanocomposite with in situ surfaces/interfaces organic encapsulation for the first time. The built‐in oxygen‐ and/or moisture‐isolating organic layer of subangstrom thickness not only avoids the SEI formation, but also guarantees monodisperse and ultrasmall dimensions of ZnO nanocrystals, which are crucial for the high initial Coulombic efficiency (ICE) and fully reversible conversion. Benefiting from the high ICE up to 91.4%, stable long‐term cyclibility (95% capacity retention at 1 A g^?1 after 1400 cycles), and no sacrificing Li‐ion storage capability (868 mAh g^?1 at 0.1 A g^?1), the ZnO nanocomposite demonstrates the highest initial Li‐ion utilization efficiency (ILUE, ≈85.4%) among previous transition metal oxide–based full cells.     

Mn‐Rich P′2‐Na0.67[Ni0.1Fe0.1Mn0.8]O2 as High‐Energy‐Density and Long‐Life Cathode Material for Sodium‐Ion Batteries

Herein, P′2‐type Na_0.67[Ni_0.1Fe_0.1Mn_0.8]O₂ is introduced as a promising new cathode material for sodium‐ion batteries (SIBs) that exhibits remarkable structural stability during repetitive Na⁺ de/intercalation. The O? Ni? O? Mn? O? Fe? O bond in the octahedra of transition‐metal layers is used to suppress the elongation of the Mn? O bond and to improve the electrochemical activity, leading to the highly reversible Na storage mechanism. A high discharge capacity of ≈220 mAh g^?1 (≈605 Wh kg^?1) is delivered at 0.05 C (13 mAg^?1) with a high reversible capacity of ≈140 mAh g^?1 at 3 C and excellent capacity retention of 80% over 200 cycles. This performance is associated with the reversible P′2–OP4 phase transition and small volume change upon charge and discharge (≈3%). The nature of the sodium storage mechanism in a full cell paired with a hard carbon anode reveals an unexpectedly high energy density of ≈542 Wh kg^?1 at 0.2 C and good capacity retention of ≈81% for 500 cycles at 1 C (260 mAg^?1).     

Template‐Free Construction of Self‐Supported Sb Prisms with Stable Sodium Storage

Antimony (Sb) is a promising anode material for sodium‐ion batteries owing to its large capacity of 660 mAh g^?1. However, its practical application is restricted by the rapid capacity decay resulted from a large volume expansion up to 390% upon Na alloying. Herein, construction of a self‐supported Sb array that has enough space allowing for effective accommodation of the volume change is reported. The array of Sb prisms is directly grown on a Cu substrate via a template‐free electrodeposition, followed by mild heating to consolidate the structural integrity between Sb and Cu. The resulting 3D architecture endows the Sb array with excellent sodium storage performance, exhibiting a reversible capacity of 578 mAh g^?1 and retaining 531 mAh g^?1 over 100 cycles at 0.5 C. The potential of Sb array in sodium‐ion full cells by pairing it with a Na_0.67(Ni_0.23Mg_0.1Mn_0.67)O₂ cathode is further demonstrated. This full cell affords a specific energy of 197 Wh kg^?1 at 0.2 C and a specific power of 1280 W kg^?1 at 5 C. Considering its low cost and scale‐up capability, the template‐free route may find extensive applications in designing electrode architectures.     

Root colonisation of Pseudomonas aeruginosa strain UPMP3 and induction of defence‐related genes in oil palm (Elaeis guineensis)

Pseudomonas aeruginosa strain UPMP3 labelled with β‐glucuronidase (gusA) and green fluorescent protein (gfp) by electrotransformation yielded ca 1 × 10⁷ transformants µg^?1 DNA. The data obtained from the dilution plate count showed that over 28 days both epiphytic and endophytic populations of P. aeruginosa strain UPMP3 increased from 5.76 log₁₀ [colony forming unit (CFU) + 1] g^?1 fresh weight (FW) to 8.19 log₁₀ (CFU + 1) g^?1 FW and 4.10 log₁₀ (CFU + 1) g^?1 FW to 6.23 (CFU + 1) g^?1 FW, respectively. Confocal laser scanning microscopic analysis of oil palm roots treated with gusA:gfp‐tagged P. aeruginosa strain UPMP3 showed intense root colonisation over the sampling period. The root surface colonisation by P. aeruginosa strain UPMP3 was followed by a second stage, characterised by cortical infection, and a third stage, which involves xylem ingression. The colonisation of oil palm roots by the gusA:gfp‐tagged strain was concentrated on root areas potentially rich in nutrients such as the elongation zones, ridges between epidermal cells and points of secondary adventitious root emergence. Different expression levels of defence‐related genes, namely, chitinase and β‐1,3‐glucanase in the strain UPMP3–host interaction recorded over 28 days, suggested the potential role of P. aeruginosa strain UPMP3 in triggering the defence mechanism in oil palm. This is the first report on root colonisation and upregulation of defence‐related genes on oil palm roots by P. aeruginosa strain UPMP3 and shows the potential of this strain to be used as a biocontrol agent in oil palm.     

Paper‐Based Energy‐Storage Devices Comprising Carbon Fiber‐Reinforced Polypyrrole‐Cladophora Nanocellulose Composite Electrodes

Composites of polypyrrole (PPy) and Cladophora nanocellulose, reinforced with 8 μm‐thick chopped carbon filaments, can be used as electrode materials to obtain paper‐based energy‐storage devices with unprecedented performance at high charge and discharge rates. Charge capacities of more than 200 C g^?1 (PPy) are obtained for paper‐based electrodes at potential scan rates as high as 500 mV s^?1, whereas cell capacitances of ～60–70 F g^?1 (PPy) are reached for symmetric supercapacitor cells with capacitances up to 3.0 F (i.e.,0.48 F cm^?2) when charged to 0.6 V using current densities as high as 31 A g^?1 based on the PPy weight (i.e., 99 mA cm^?2). Energy and power densities of 1.75 Wh kg^?1 and 2.7 kW kg^?1, respectively, are obtained when normalized with respect to twice the PPy weight of the smaller electrode. No loss in cell capacitance is seen during charging/discharging at 7.7 A g^?1 (PPy) over 1500 cycles. It is proposed that the nonelectroactive carbon filaments decrease the contact resistances and the resistance of the reduced PPy composite. The present straightforward approach represents significant progress in the development of low‐cost and environmentally friendly paper‐based energy‐storage devices for high‐power applications.     

Lithium‐Pretreated Hard Carbon as High‐Performance Sodium‐Ion Battery Anodes

Hard carbon (HC) is the state‐of‐the‐art anode material for sodium‐ion batteries (SIBs). However, its performance has been plagued by the limited initial Coulombic efficiency (ICE) and mediocre rate performance. Here, experimental and theoretical studies are combined to demonstrate the application of lithium‐pretreated HC (LPHC) as high‐performance anode materials for SIBs by manipulating the solid electrolyte interphase in tetraglyme (TEGDME)‐based electrolyte. The LPHC in TEGDME can 1) deliver > 92% ICE and ≈220 mAh g^?1 specific capacity, twice of the capacity (≈100 mAh g^?1) in carbonate electrolyte; 2) achieve > 85% capacity retention over 1000 cycles at 1000 mA g^?1 current density (4 C rate, 1 C = 250 mA g^?1) with a specific capacity of ≈150 mAh g^?1, ≈15 times of the capacity (10 mAh g^?1) in carbonate. The full cell of Na₃V₂(PO₄)₃‐LPHC in TEGDME demonstrated close to theoretical specific capacity of ≈98 mAh g^?1 based on Na₃V₂(PO₄)₃ cathode, ≈2.5 times of the value (≈40 mAh g^?1) with nontreated HC. This work provides new perception on the anode development for SIBs.     

A High‐Volumetric‐Capacity Cathode Based on Interconnected Close‐Packed N‐Doped Porous Carbon Nanospheres for Long‐Life Lithium–Sulfur Batteries

This study reports a Li–S battery cathode of high volumetric capacity enabled by novel micro‐ and mesostructuring. The cathode is based on monodisperse highly porous carbon nanospheres derived from a facile template‐ and surfactant‐free method. At the mesoscale, the nanospheres structure into interconnected close‐packed clusters of a few microns in extent, thus facilitating the fabrication of dense crack‐free high areal sulfur loading (5 mg cm^?2) cathodes with high electrical conductivity and low cathode impedance. A combination of the nitrogen doping (5 wt%), high porosity (2.3 cm³ g^?1), and surface area (2900 m² g^?1) at the microscale enables high sulfur immobilization and utilization. The cathode delivers among the best reported volumetric capacity to date, above typical Li‐ion areal capacity at 0.2 C over 200 cycles and low capacity fading of 0.1% per cycle at 0.5 C over 500 cycles. The compact cathode structure also ensures a low electrolyte requirement (6 µL mg^?1), which aids a low overall cell weight, and further, among the best gravimetric capacities published to date as well.     

A Dual‐Insertion Type Sodium‐Ion Full Cell Based on High‐Quality Ternary‐Metal Prussian Blue Analogs

Prussian blue analogs (PBAs) are especially investigated as superior cathodes for sodium‐ion batteries (SIBs) due to high theoretical capacity (≈170 mA h g^?1) with 2‐Na storage and low cost. However, PBAs suffer poor cyclability due to irreversible phase transition in deep charge/discharge states. PBAs also suffer low crystallinity, with considerable [Fe(CN)₆] vacancies, and coordinated water in crystal frameworks. Presently, a new chelating agent/surfactant coassisted crystallization method is developed to prepare high‐quality (HQ) ternary‐metal Ni_xCo_1?x[Fe(CN)₆] PBAs. By introducing inactive metal Ni to suppress capacity fading caused by excessive lattice distortion, these PBAs have tunable limits on depth of charge/discharge. HQ‐Ni_xCo_1?x[Fe(CN)₆] (x = 0.3) demonstrates the best reversible Na‐storage behavior with a specific capacity of ≈145 mA h g^?1 and a remarkably improved cycle performance, with ≈90% capacity retention over 600 cycles at 5 C. Furthermore, a dual‐insertion full cell on the cathode and NaTi₂(PO₄)₃ anode delivers reversible capacity of ≈110 mA h g^?1 at a current rate of 1.0 C without capacity fading over 300 cycles, showing promise as a high‐performance SIB for large‐scale energy‐storage systems. The ultrastable cyclability achieved in the lab and explained herein is far beyond that of any previously reported PBA‐based full cells.     

Phycoremediation potential,physiological, and biochemical response of <Emphasis Type="Italic">Amphora subtropica</Emphasis> and <Emphasis Type="Italic">Dunaliella</Emphasis> sp. to nickel pollution

Metal pollution can produce many biological effects on aquatic environments. The marine diatom Amphora subtropica and the green alga Dunaliella sp. possess a high metal absorption capacity. Nickel (Ni) removal by living cells of A. subtropica and Dunaliella sp. was tested in cultures exposed to different Ni concentrations (100, 200, 300, and 500 mg L^?1). The amount of Ni removed by the microalgae increased with the time of exposure and the initial Ni concentration in the medium. The metal, which was mainly removed by bioadsorption to Dunaliella sp. cell surfaces (93.63% of total Ni (for 500 mg Ni L^?1) and by bioaccumulation (80.82% of total Ni (for 300 mg Ni L^?1) into Amphora subtropica cells, also inhibited growth. Exposure to Ni drastically reduced the carbohydrate and protein concentrations and increased total lipids from 6.3 to 43.1 pg cell^?1, phenolics 0.092 to 0.257 mg GAE g^?1 (Fw), and carotenoid content, from 0.08 to 0.59 mg g^?1 (Fw), in A. subtropica. In Dunaliella sp., total lipids increased from 26.1 to 65.3 pg cell^?1, phenolics from 0.084 to 0.289 mg GAE g^?1 (Fw), and carotenoid content from 0.41 to 0.97 mg g^?1 (Fw). These compounds had an important role in protecting the algae against ROS generated by Ni. In order to cope with Ni stress shown by the increase of TBARS level, enzymatic (SOD, CAT, and GPx) ROS scavenging mechanisms were induced.     

Cobalt‐Free High‐Capacity Ni‐Rich Layered Li[Ni0.9Mn0.1]O2 Cathode

Li[Ni_0.9Co_0.1]O₂ (NC90), Li[Ni_0.9Co_0.05Mn_0.05]O₂ (NCM90), and Li[Ni_0.9Mn_0.1]O₂ (NM90) cathodes are synthesized for the development of a Co‐free high‐energy‐density cathode. NM90 maintains better cycling stability than the two Co‐containing cathodes, particularly under harsh cycling conditions (a discharge capacity of 236 mAh g^?1 with a capacity retention of 88% when cycled at 4.4 V under 30 °C and 93% retention when cycled at 4.3 V under 60 °C after 100 cycles). The reason for the enhanced stability is mainly the ability of NM90 to absorb the strain associated with the abrupt anisotropic lattice contraction/extraction and to suppress the formation of microcracks, in addition to enhanced chemical stability from the increased presence of stable Mn⁴⁺. Although the absence of Co deteriorates the rate capability, this can be overcome as the rate capability of the NM90 approaches that of the NCM90 when cycled at 60 °C. The long‐term cycling stability of NM90 is confirmed in a full cell, demonstrating that it is one of the most promising Co‐free cathodes for high‐energy‐density applications. This study not only provides insight into redefining the role of Mn in a Ni‐rich cathode, it also represents a clear breakthrough in achieving a commercially viable Co‐free Ni‐rich layered cathode.     

High and Reversible Lithium Ion Storage in Self‐Exfoliated Triazole‐Triformyl Phloroglucinol‐Based Covalent Organic Nanosheets

Covalent organic framework (COF) can grow into self‐exfoliated nanosheets. Their graphene/graphite resembling microtexture and nanostructure suits electrochemical applications. Here, covalent organic nanosheets (CON) with nanopores lined with triazole and phloroglucinol units, neither of which binds lithium strongly, and its potential as an anode in Li‐ion battery are presented. Their fibrous texture enables facile amalgamation as a coin‐cell anode, which exhibits exceptionally high specific capacity of ≈720 mA h g^?1 (@100 mA g^?1). Its capacity is retained even after 1000 cycles. Increasing the current density from 100 mA g^?1 to 1 A g^?1 causes the specific capacity to drop only by 20%, which is the lowest among all high‐performing anodic COFs. The majority of the lithium insertion follows an ultrafast diffusion‐controlled intercalation (diffusion coefficient, D_Li⁺ = 5.48 × 10^?11 cm² s^?1). The absence of strong Li‐framework bonds in the density functional theory (DFT) optimized structure supports this reversible intercalation. The discrete monomer of the CON shows a specific capacity of only 140 mA h g^?1 @50 mA g^?1 and no sign of lithium intercalation reveals the crucial role played by the polymeric structure of the CON in this intercalation‐assisted conductivity. The potentials mapped using DFT suggest a substantial electronic driving‐force for the lithium intercalation. The findings underscore the potential of the designer CON as anode material for Li‐ion batteries.