Two ways to achieve an anammox influent from real reject water treatment at lab-scale: Partial SBR nitrification and SHARON process

A comparative study to produce the correct influent for Anammox process from anaerobic sludge reject water (700–800 mg NH₄⁺-N L⁻¹) was considered here. The influent for the Anammox process must be composed of NH₄⁺-N and NO₂⁻-N in a ratio 1:1 and therefore only a partial nitrification of ammonium to nitrite is required. The modifications of parameters (temperature, ammonium concentration, pH and solid retention time) allows to achieve this partial nitrification with a final effluent only composed by NH₄⁺-N and NO₂⁻-N at the right stoichiometric ratio. The equal ratio of HCO₃⁻/NH₄⁺ in reject water results in a natural pH decrease when approximately 50% of NH₄⁺ is oxidised. A Sequencing batch reactor (SBR) and a chemostat type of reactor (single-reactor high activity ammonia removal over nitrite (SHARON) process) were studied to obtain the required Anammox influent. At steady state conditions, both systems had a specific conversion rate around 40 mg NH₄⁺-N g⁻¹ volatile suspended solids (VSS) h⁻¹, but in terms of absolute nitrogen removal the SBR conversion was 1.1 kg N day⁻¹ m⁻³, whereas in the SHARON chemostat was 0.35 kg N day⁻¹ m⁻³ due to the different hydraulic retention time (HRT) used. Both systems are compared from operational (including starvation experiments) and kinetic point of view and their advantages/disadvantages are discussed.     

Application of polyethylene glycol immobilized Clostridium sp. LS2 for continuous hydrogen production from palm oil mill effluent in upflow anaerobic sludge blanket reactor

A novel polyethylene glycol (PEG) gel was fabricated and used as a carrier to immobilize Clostridium sp. LS2 for continuous hydrogen production in an upflow anaerobic sludge blanket (UASB) reactor. Palm oil mill effluent (POME) was used as the substrate carbon source. The optimal amount of PEG-immobilized cells for anaerobic hydrogen production was 12% (w/v) in the UASB reactor. The UASB reactor containing immobilized cells was operated at varying hydraulic retention times (HRT) that ranged from 24 to 6 h at 3.3 g chemical oxygen demand (COD)/L/h organic loading rate (OLR), or at OLRs that ranged from 1.6 to 6.6 at 12 h HRT. The best volumetric hydrogen production rate of 336 mL H₂/L/h (or 15.0 mmol/L/h) with a hydrogen yield of 0.35 L H₂/g COD_removed was obtained at a HRT of 12 h and an OLR of 5.0 g COD/L/h. The average hydrogen content of biogas and COD reduction were 52% and 62%, respectively. The major soluble metabolites during hydrogen fermentation were butyric acid followed by acetic acid. It is concluded that the PEG-immobilized cell system developed in this work has great potential for continuous hydrogen production from real wastewater (POME) using the UASB reactor.     

Removal of carbon and nutrients from low strength domestic wastewater by expanded granular sludge bed-zeolite bed filtration (EGSB-ZBF) integrated treatment concept

The performance of an expanded granular sludge bed (EGSB) reactor coupled with zeolite bed filtration (ZBF) for treating low strength domestic wastewater was monitored at 35 °C for 7 months. The whole operation period of EGSB system was divided into five phases. Each phase ran at up-flow velocity (m/h) of 0.51, 1.02, 3.57, 2.05, 9.69, and hydraulic retention time (HRT) (h) of 6, 3, 0.87, 1.5, 0.32, respectively. The influent chemical oxygen demand (COD) was kept approximate at 150 ± 100 mg/L. Under these conditions, the COD removal efficiency of using EGSB system in five phases reached to 81.08, 57.94, 82.79, 56.58 and 79.52%, respectively. Moreover, since nutrients such as NH₄⁺ and PO₄³⁻ were only removed to a limited extent by EGSB, additional treatment is required. The ZBF was employed in phase 2 as a post-treatment following EGSB. NH₄⁺ and PO₄³⁻ concentrations were decreased by 100%, respectively, in the first 2 or 3 d using fresh zeolite. The simple design and excellent treatment performance indicated that this system could be used as a novel Sewage Integrated Treatment System (SITS) for developing country especially in a tropical area.     

Anaerobic treatment of saline wastewater by Halanaerobium lacusrosei

An upflow anaerobic packed bed reactor was operated continuously with synthetic saline wastewater at different initial COD concentrations (COD₀ = 1900–6300 mg/L), salt concentrations (0–5%, w/v) and hydraulic retention times (θ_H = 11–30 h) to investigate the effect of those operating parameters on COD removal from saline synthetic wastewater. Anaerobic salt tolerant bacteria, Halanaerobium lacusrosei, were used as dominant microbial culture in the process. The percent COD removal reached up to 94% at COD₀ = 1900 mg/L, 19 h hydraulic retention time and 3% salt concentration. No substrate inhibition effect was observed at high feed CODs. Increasing hydraulic retention time from 11 h to 30 h resulted in a substantial improvement in the COD removal from 60% to 84% at around COD₀ = 3400 mg/L and 3% salt concentration. Salt inhibition effect on COD utilization was observed at above 3% salt concentration. Modified Stover–Kincannon model was applied to the experimental data to determine the biokinetic coefficients. Saturation value constant, and maximum utilization rate constant of Stover–Kincannon model for COD were determined as K_B = 5.3 g/L day, U_max = 7.05 g/L day, respectively.     

An integrated anaerobic–aerobic bioreactor (IAAB) for the treatment of palm oil mill effluent (POME): Start-up and steady state performance

Palm oil mill effluent (POME) with average chemical oxygen demand (COD) and biochemical oxygen demand (BOD) of 70,000 and 30,000 mg/L, respectively, can cause serious environmental hazards if discharged untreated. There are conventional palm oil mill effluent (POME) treatment systems that require large footprint, long HRT and fail to meet the Malaysian Department of Environment (DOE) discharge limit. Hence, the current research is aimed to design a novel integrated anaerobic–aerobic bioreactor (IAAB) for POME treatment in order to overcome these shortcomings of the conventional system. IAAB is a new bioreactor configuration which integrates anaerobic and aerobic digestion in one reactor. The overall removal efficiencies in steady state condition in terms of chemical oxygen demand (COD), biochemical oxygen demand (BOD) and total suspended solids (TSS) were more than 99% at the organic loading rate (OLR) of 10.5 g COD/L day with methane yield of 0.24 L CH₄/g COD removed. The effluent quality remained stable (BOD < 70 mg/L) and complied with the discharge limit (BOD < 100 mg/L). Overall, the IAAB system exhibited good stability and pH adjustment was unnecessary. The results show that the IAAB achieves higher performance in terms of organic removal efficiency and methane yield at higher OLR and shorter HRT as compared to the conventional system. Further evaluations of its long-term performance are proposed for the subsequent study.     

Dairy wastewater polluting load and treatment performances of an industrial three-cascade-reactor plant

An industrial three-cascade-reactor plant treating 45 m³ d^?1 of dairy wastewater (DW) was monitored for approx. one year to investigate the effect of variable daily influent loads. It removed more than 85% COD, NH₄-N and non-ionic and anionic surfactants from DW within the loads 7–24, 0.4–2.3, 0.4–0.7 and 0.1–0.5 kg d^?1, respectively; NH₄-N removal, in particular, was almost quantitative. Although the degradation of the above parameters below the lower load thresholds declined to 78.7, 87.5, 50.2 and 64.7%, respectively, their residual concentrations met effluent discharge standards. The biomass settling properties, assessed as sludge volume index (SVI), were satisfactory (generally lower than 150 ml g^?1) regardless of the organic load of the influent. The depletion of the pollutant load took mainly place in the first reactor albeit a significant contribution to the removal of the slowly degradable organic matter fraction was given by the two subsequent reactors.     

Microbial community in conventional and extended aeration activated sludge plants in India

This study was conducted to determine the relationship between the ciliated protozoan population density and the effluent quality at two different modes of activated sludge plants (ASP) operating in India. A wide variety of ciliated protozoa (26 sp.) in higher density were identified at the conventional ASP, Haridwar, that delivered high quality effluent in terms of low biochemical oxygen demand (BOD = 15 mg/L), suspended solids (SS = 17 mg/L), turbidity (2.7 NTU), ammoniacal nitrogen (NH₃–N = 3 mg/L), chemical oxygen demand (COD = 37 mg/L), total coliforms (TC = log 5.2), fecal coliforms (FC = log 4.7) and fecal Streptococci (FS = log 3.7). Whereas, a few protozoan species (15 sp.) in lower density were reported in extended aeration plant (EAP) Delhi, that delivered turbid and lower quality effluent in terms of high BOD (23 mg/L), SS (80 mg/L), turbidity (12 NTU), NH₃–N (55 mg/L) and COD (68 mg/L). However, in spite of relatively poor effluent quality, lower concentration of TC (log 4.2), FC (log 3.9) and FS (log 3.2) was observed in EAP, Delhi. The constant presence of two filamentous bacterial species (Beggiatoa and Spirillum) in extended aeration process can be considered as the probable reason of high coliforms removal, since filamentous bacteria are capable of removing organic as well as microbial pollutants from wastewater.     

Characteristics of nitrous oxide (N2O) emission from intermittently aerated sequencing batch reactors (IASBRs) treating slaughterhouse wastewater at low temperature

This study investigated the characteristics of nitrous oxide (N₂O) emission from intermittently aerated sequencing batch reactors (IASBRs) treating high strength slaughterhouse wastewater at 11 °C, where partial nitrification followed by denitrification (PND) was achieved. N₂O generation and emission was examined at three aeration rates of 0.4, 0.6, and 0.8 L air/min in three IASBRs (SBR1, SBR2, and SBR3, respectively). The slaughterhouse wastewater contained chemical oxygen demand (COD) of 6057 ± 172.6 mg/L, total nitrogen (TN) of 576 ± 15.1 mg/L, total phosphorus (TP) of 52 ± 2.7 mg/L and suspended solids (SS) of 1843 ± 280.5 g/L. In the pseudo-steady state, the amount of N₂O emission was up to 5.7–11.0% of incoming TN. The aeration rate negatively affected N₂O emission and the ratio of N₂O emission to incoming TN was reduced by 48.2% when the aeration rate was increased from 0.4 to 0.8 L air/min. Results showed that more N₂O was generated in non-aeration periods than in aeration periods. Lower DO concentrations enhanced N₂O generation in the aeration periods (probably via nitrifier denitrification) while low DO concentrations (lower than 0.2 mg/L) did not affect N₂O generation in the non-aeration periods (probably via heterotrophic denitrification). When PHB was utilized as the organic substrate for denitrification, there was a high N₂O generation potential. It was estimated that 1.8 mg N₂O-N was generated accompanying per mg PHB consumed.     

Potentials of anaerobic treatment for catalytically oxidized olive mill wastewater (OMW)

The catalytically oxidized olive mill wastewater (OMW) was subjected to continuous anaerobic treatment using two treatment schemes. The 1st step in both schemes was an up-flow anaerobic sludge blanket (UASB) reactor (2 0 l). The 2nd step was either a hybrid UASB reactor or a classical one (1 0 l, each). The 1st stage was operated at constant hydraulic retention time (HRT) of 24 h. The organic loading rate (OLR) varied from 3.4 to 4.8 kgCOD/m³ d depending on the quality of the pretreated wastewater. The results obtained indicated that, the 1st step UASB reactor achieved a COD percentage removal value of 53.9%. Corresponding total BOD₅ and TSS removal were 51.5% and 68.3%, respectively.The results obtained indicated that the hybrid UASB reactor as a 2nd step produced better quality effluent as compared to the classical one. This could be attributed to the presence of the packing curtain sponge with active biomass in the sedimentation part of hybrid UASB reactor which minimizes suspended solids washout, consequently enhancement of the efficiency of the reactor.Available data showed that a two stage system consisting of a classical and a hybrid UASB reactor operated at a total HRT of 48 h and OLR of 2.0 kgCOD/m³ d provided promising results. Removal values of COD_total, BOD_5 total, TOC, VFA, oil and grease were 83%, 84%, 81%, 93% and 81%, respectively. Based on the available data, the use of a two stage anaerobic system consisting of a classical UASB reactor followed by a hybrid UASB as a post-treatment step for catalytically oxidized OMW is recommended.     

Control and optimization of nitrifying communities for nitritation from domestic wastewater at room temperatures

To achieve nitritation from complete-nitrification seed sludge at room temperature of 19 ± 1 °C, a lab-scale sequencing batch reactor (SBR) treating domestic wastewater with low C/N ratios was operated to investigate the control and optimization of nitrifying communities. Ammonia oxidizing bacteria (AOB) dominance was enhanced through the combination of low DO concentrations (<1.0 mg/L) and preset short-cycle control of aeration time. Nitritation was successfully established with NO₂^?-N/NO_x^?-N over 95%. To avoid the adverse impact of low DO concentrations on AOB activities, DO concentrations were increased to 1–2 mg/L. At the normal DO levels and temperatures, on-line control strategy of aerobic durations maintained the stability of nitritation with nitrite accumulation rate over 95% and ammonia removal above 97%. Fluorescence in-situ hybridization (FISH) analysis presented that the maximal percentage of AOB in biomass reached 10.9% and nitrite oxidizing bacteria (NOB) were washed out.     

Removal of nutrients from wastewater with Canna indica L. under different vertical-flow constructed wetland conditions

Constructed wetlands are becoming increasingly popular worldwide for removing contaminants from domestic wastewater. This study investigated the removal efficiency of nitrogen (N) and phosphorus (P) from wastewater with the simulated vertical-flow constructed wetlands (VFCWs) under three different substrates (i.e., BFAS or blast furnace artificial slag, CBAS or coal burn artificial slag, and MSAS or midsized sand artificial slag), hydraulic loading rates (i.e., 7, 14, and 21 cm d^?1), and wetland operational periods (0.5, 1, and 2 years) as well as with and without planting Canna indica L. The wastewater was collected from the campus of South China Agricultural University, Guangzhou, China. Results show that the percent removal of total P (TP) and ammonium N (NH₄⁺-N) by the substrates was BFAS > CBAS > MSAS due to the high contents of Ca and Al in substrate BFAS. In contrast, the percent removal of total N (TN) by the substrates was CBAS > MSAS > BFAS due to the complicated nitrification/denitrification processes. The percent removal of nutrients by all of the substrates was TP > NH₄⁺-N > TN. About 10% more TN was removed from the wastewater after planting Canna indica L. A lower hydraulic loading rate or longer hydraulic retention time (HRT) resulted in a higher removal of TP, NH₄⁺-N, and TN because of more contacts and interactions among nutrients, substrates, and roots under the longer HRT. Removal of NO₃^?N from the simulated VFCWs is a complex process. A high concentration of NO₃^?N in the effluent was observed under the high hydraulic loading rate because more NH₄⁺-N and oxygen were available for nitrification and a shorter HRT was unfavorable for denitrification. In general, a longer operational period had a highest removal rate for nutrients in the VFCWs.     

Thermophilic treatment of bulk drug pharmaceutical industrial wastewaters by using hybrid up flow anaerobic sludge blanket reactor

The hybrid up flow anaerobic sludge blanket reactor was evaluated for efficacy in reduction of chemical oxygen demand (COD) and biochemical oxygen demand (BOD) of bulk drug pharmaceutical wastewater under different operational conditions. The start-up of the reactor feed came entirely with glucose, applied at an organic loading rate (OLR) 1 kg COD/m³ d. Then the reactor was studied at different OLRs ranging from 2 to 11 kg COD/m³ d with pharmaceutical wastewater. The optimum OLR was found to be 9 kg COD/m³ d, where we found 65–75% COD and 80–94% of BOD reduction with biogas production containing 60–70% of methane and specific methanogenic activity was 320 ml CH₄/g-VSS d. By the characterization studies of effluent using GC–MS, the hazardous compounds like phenol, l,2-methoxy phenol, 2,4,6-trichloro phenol, dibutyl phthalate, 1-bromo naphthalene, carbamazepine and antipyrine were present. After the treatment, these compounds degraded almost completely except carbamazepine. Thermophilic methanothrix and methanosaetae like bacteria are present in the granular sludge.     

Sewage treatment in a combined up-flow anaerobic sludge blanket (UASB)–down-flow hanging sponge (DHS) system

The performance of up-flow anaerobic sludge blanket (UASB) in combination with down-flow hanging sponge (DHS) system for sewage treatment at an average wastewater temperature of 15 °C has been investigated for 6 months. The results showed that a combined system operated at a total HRT of 10.7 h and total SRT of 88 days represents a cost effective sewage treatment process. The average COD_total and BOD_5 total concentrations measured in the final effluent of the total system (UASB + DHS) amounted to 43 and 3.0 mg/l, respectively, corresponding to the overall removal efficiency of 90% for COD_total and 98% for BOD_5 total. The total process provided a final effluent containing a low concentration of 12 mg/l for TSS.Eighty-six percent of ammonia was eliminated at space loading rate of 1.6 kg COD/m³ d and HRT of 2.7 h. The calculated nitrification rate of the DHS system according to the nitrate and nitrite production amounted to 0.18 kg/m³ d. The removal of F. coliform in the UASB reactor only amounted to 0.86 log₁₀. On the other hand, the F. coliform concentration dropped substantially, i.e. by 2.6 log₁₀ in the DHS system resulting only 2.7 × 10³/100 ml in the final effluent.The calculated average sludge production for UASB operated at an HRT of 8.0 h amounted to 30 g TSS/d, corresponding to sludge yield coefficient of 0.2 g TSS/g total COD removed, while it was indeed very low only 6.0 g TSS/d corresponding to sludge yield coefficient of 0.09 g TSS/g total COD removed, for DHS system.The DHS profile results revealed that in the first and second segment of DHS system, the COD_total, BOD_5 total and TSS was eliminated, followed by the oxidation of ammonia in the next segments.     

Effect of hydraulic retention time on the treatment of secondary effluent in a subsurface flow constructed wetland

This study evaluates the potential of subsurface flow (SSF) constructed wetlands (CWs) for tertiary treatment of wastewater at four shorter HRTs (1–4 days). The CWs were planted with Typha angustata, which was observed in our earlier study to be more efficient than Phragmites karka and Scirpus littoralis. The CWs comprised four rectangular treatment cells (2.14 m × 0.76 m × 0.61 m) filled with layers of gravel of two different sizes (approximately 2.5 cm and 1.5 cm diameter) to a depth of 0.61 m. The inflow rates of the secondary effluent in the four cells were accordingly fixed at 300 L d^?1, 150 L d^?1, 100 L d^?1 and 75 L d^?1, respectively, for 1, 2, 3 and 4 days HRT. The hydraulic loads ranged between 59.05 mm d^?1 and 236.22 mm d^?1.The wastewater inflow into the CW system as well as the treated effluent were analyzed, using standard methods, at regular intervals for various forms of nitrogen (NH₄-N, NO₃-N and TKN), orthophosphate-P and organic matter (BOD and COD) concentrations over a period of five weeks after the development of a dense stand.The higher HRT of 4 days not only helped maximum removal of all the pollutants but also maintained the stability of the treatment efficiency throughout the monitoring period. For the nutrients (NH₄-N, NO₃-N and TKN), HRT played a more significant role in their removal than in case of organic matter (BOD₃ and COD). More than 90% of NO₃-N and TKN and 100% of NH₄-N were removed from the wastewater at 4 days HRT.At lower HRTs, the mass loading rate was higher with greater fluctuation. However mass reduction efficiency of the T. angustata CW for all forms of nitrogen was >80% with the HRTs of 2, 3 and 4 days.     

Prefermentation to overcome nutrient limitations in food processing wastewater: Comparison of pilot- and bench-scale systems

A bench- and a pilot-scale anaerobic/aerobic system were evaluated for the treatment of high strength tomato-processing wastewater. The pilot-scale anaerobic tank achieved better prefermentation of organic carbon and nitrogen than the bench-scale system, although overall system performance was comparable with more than 99% SBOD removal and 97% SCOD removal. Hydraulic retention time (HRT) and temperature effects were studied in the bench-scale system. Increase of anaerobic HRT from 0.25 day to 0.5 day favored prefermentation and a better effluent quality was achieved, as demonstrated by reduction in TSS concentrations from 66 mg/L to 24 mg/L, SCOD from 103 mg/L to 78 mg/L and SBOD from 8 mg/L to 6 mg/L, respectively. Specific oxygen uptake rate (SOUR) increased from 0.15–0.23 mg O₂/mg VSS day at 25 °C to 0.67–1.24 mg O₂/mg VSS day at 32 °C. Settling characteristics deteriorated from sludge volume index (SVI) of 24–131 mL/g at 25 °C to 115–173 mL/g at 32 °C. Sludge yield decreased from 0.14 g VSS/g COD at 25 °C to 0.098 g VSS/g COD at 32 °C.     

Comparison between a moving bed membrane bioreactor and a conventional membrane bioreactor on organic carbon and nitrogen removal

A membrane bioreactor filled with carriers instead of activated sludge named a moving bed membrane bioreactor (MBMBR) was investigated for simultaneously removing organic carbon and nitrogen in wastewater. Its performance was compared with a conventional membrane bioreactor (CMBR) at various influent COD/TN ratios of 8.9–22.1. The operational parameters were optimized to increase the treatment efficiency. COD removal efficiency averaged at 95.6% and 96.2%, respectively, for MBMBR and CMBR during the 4 months experimental period. The MBMBR system demonstrated good performance on nitrogen removal at different COD/TN ratios. When COD/TN was 8.9 and the total nitrogen (TN) load was 7.58 mg/l h, the TN and ammonium nitrogen removal efficiencies of the MBMBR were maintained over 70.0% and 80.0%, respectively, and the removed total nitrogen (TN) load reached to 5.31 mg/l h. Multifunctional microbial reactions in the carrier, such as simultaneous nitrification and denitrification (SND), play important roles in nitrogen removal. In comparison, the CMBR did not perform so well. Its TN removal was not stable, and the removed total nitrogen (TN) load was only 1.02 mg/l h at COD/TN ratio 8.9. The specific oxygen utilization rate (SOUR) showed that the biofilm has a better microbial activity than an activated sludge. Nevertheless, the membrane fouling behavior was more severe in the MBMBR than in the CMBR due to a thick and dense cake layer formed on the membrane surface, which was speculated to be caused by the filamentous bacteria in the MBMBR.     

Efficient nitrogen removal in a pilot system based on upflow multi-layer bioreactor for treatment of strong nitrogenous swine wastewater

In order to prevent the toxic effect caused by high strength ammonium in a swine wastewater treatment system, a patented upflow multi-layer bioreactor (UMBR) as a pre-anoxic tank was applied to a pilot-scale plant with a treatment capacity of 5 m³/d. This plant was operated for 4 months at a high IR ratio in the range of 10–17, in order to alleviate the toxic effects caused by high strength ammonium. A computational fluid dynamic (CFD) analysis was also conducted to design and configure the rotating distributors in the UMBR. At an IR ratio of about 17, the influent NH₄⁺-N (1169 mg N/L) was diluted to less than 80 mg N/L at the head of the UMBR, and then was completely nitrified (about 98.3%) in the aeration tank, without any inhibition caused by high strength ammonium. The nitrate at a concentration of about 58.2 mg N/L recycled from the aeration tank was completely denitrified in UMBR #1, which was operated at an actual hydraulic retention time (HRT) of 3.5 h.     

Performance evaluation of various bioreactors for the removal of Cr(VI) and organic matter from industrial effluent

Performances of various bioreactors under different operating conditions were evaluated with respect to hexavalent chromium (Cr(VI)) reduction and COD removal. Continuous reactor studies were carried out with (i) aerobic suspended growth system, (ii) aerobic attached growth system, and (iii) anoxic attached growth system, using both synthetic and actual industrial wastewater. Arthrobacter rhombi-RE (MTCC7048), a Cr(VI) reducing strain enriched and isolated from chromium contaminated soil, was used in all the bioreactors for Cr(VI) biotransformation and COD removal. Aerobic and anoxic batch experiments were conducted to evaluate the bio-kinetic parameters. The bio-kinetic parameters for aerobic system were: μ_max = 2.34/d, K_s = 190 mg/L (as COD), K_i = 3.8 mg/L of Cr(VI), and Y_T = 0.377. These parameters for anoxic conditions were: μ_max = 0.57/d, K_s = 710 mg/L (as COD), K_i = 8.77 mg/L of Cr(VI), and Y_T = 0.13. Aerobic attached growth system, operated at a hydraulic retention time (HRT) of 24 h and an organic loading rate (OLR) of 3 kg/m³/d, performed better than aerobic suspended and the anoxic attached growth systems operated under identical conditions, while treating synthetic wastewater as well as industrial effluent.     

Fungal post-treatment of pulp mill effluents for the removal of recalcitrant pollutants

The objective of this work was to evaluate the post-treatment of an anaerobic recalcitrant effluent (anaerobically-treated weak black liquor, AnE) in an aerobic, upflow reactor packed with “biocubes” of Trametes versicolor immobilized onto small cubes of holm oak wood. The treated effluent (named anaerobic effluent; AnE) from an anaerobic fluidized bed reactor was fed to an up-flow aerobic fungal packed bed reactor (PBR). Two HRT were tested in this unit, namely 5 and 2.5 days; the PBR operated 60 days at 5-day HRT and 35 days at 2.5-day HRT. The aerobic packed bench scale reactor was a glass column 1.5 L total geometric volume containing 0.75 L biocubes of T. versicolor immobilized onto holm oak wood small cubes of 5 mm side. The reactor was operated at 25 °C. The pH of the AnE was adjusted to 4.5 before feeding; no carbohydrates or other soluble carbon source was supplemented. The fungal packed bed bioreactor averaged organic matter removals of 30% and 32% COD basis, during an experimental run of 60 days at 5-day HRT and 35 days at 2.5-day HRT, respectively. Colour and ligninoids contents were removed at higher percentages (69% and 54% respectively, average of both HRT). There was no significant difference between reactor performance at 5- and 2.5-day HRT, so, operation at 2.5-day HRT is recommended since reactor throughput is double. Activity of manganese peroxidase and laccase was found during the entire operation of the fungal PBR whereas lignin peroxidase activity practically disappeared in the second operation period. In general, enzyme activities were higher in the first period of operation (5-day HRT) than at 2.5-day HRT. To the best of our knowledge, this is one of the few works that demonstrated extended performance (3 months) of a fungal bioreactor for the treatment of a recalcitrant wastewater with no supplementation of glucose or other expensive, soluble carbohydrate.     

Investigation on the formation and kinetics of glucose-fed aerobic granular sludge

Aerobic granular sludge was cultivated in a glass sequencing batch reactor (SBR) with glucose synthetic wastewater. The spherical shaped granules were observed on 4th day with the mean diameter of 0.1 mm. With the increase of chemical oxygen demand (COD) concentration of the influent, aerobic granules grew matured, the size of which ranged from 1.2 to 1.9 mm. The aerobic granular sludge could sustain high organic loading rate (about 4.0 g COD L⁻¹ d⁻¹), with good settling ability (settling velocity 36 m/h) and high biomass concentration (MLSS 6.7 ±0.2 g/L). Experimental data indicated that the substrate utilization and biomass growth kinetics followed Monod's kinetics model approximately. The corresponding kinetic coefficients of maximum specific substrate utilization rate (k), half velocity coefficient (K_s), growth yield coefficient (Y) and decay coefficient (K_d) were 13.2 d⁻¹, 275.8 mg/L, 0.183–0.250 mg MLSS/mg COD and 0.023–0.075 d⁻¹, respectively, which made aerobic granules have short setup period, high rate of substrate utilization and little surplus sludge.