Anaerobic hydrogen production with an efficient carrier-induced granular sludge bed bioreactor

A novel bioreactor containing self-flocculated anaerobic granular sludge was developed for high-performance hydrogen production from sucrose-based synthetic wastewater. The reactor achieved an optimal volumetric hydrogen production rate of approximately 7.3 L/h/L (7,150 mmol/d/L) and a maximal hydrogen yield of 3.03 mol H2/mol sucrose when it was operated at a hydraulic retention time (HRT) of 0.5 h with an influent sucrose concentration of 20 g COD/L. The gas-phase hydrogen content and substrate conversion also exceeded 40 and 90%, respectively, under optimal conditions. Packing of a small quantity of carrier matrices on the bottom of the upflow reactor significantly stimulated sludge granulation that can be accomplished within 100 h. Among the four carriers examined, spherical activated carbon was the most effective inducer for granular sludge formation. The carrier-induced granular sludge bed (CIGSB) bioreactor was started up with a low HRT of 4-8 h (corresponding to an organic loading rate of 2.5-5 g COD/h/L) and enabled stable operations at an extremely low HRT (up to 0.5 h) without washout of biomass. The granular sludge was rapidly formed in CIGSB supported with activated carbon and reached a maximal concentration of 26 g/L at HRT = 0.5 h. The ability to maintain high biomass concentration at low HRT (i.e., high organic loading rate) highlights the key factor for the remarkable hydrogen production efficiency of the CIGSB processes.     

Bioreactors configured with distributors and carriers enhance the performance of continuous dark hydrogen fermentation

Anaerobic granular sludge bed (AnGSB) bioreactors were supplemented with activated carbon carriers and combined with distributors (e.g., acrylic resin board, stainless steel net and plastic net) installed at different locations to investigate the effect of distributor/carrier on biohydrogen production efficiency. The results show that plastic net stimulated the substrate/microorganisms contact and sludge granulation, thereby leading to a much better H₂ production performance when compared with those obtained from traditional CSTR. The highest H₂ production rate (7.89 L/h/L) and yield (3.42 mol H₂/mol sucrose) were obtained when two pieces of plastic nets were installed at both 4 cm and 16 cm from the bottom of AnGSB without carrier addition and the bioreactor was operated at a HRT of 0.5 h. For the AnGSB installed with two pieces of plastic net distributors, addition of carriers led to significant improvement on the H₂ production efficiency at a longer HRT (1–4 h) when compared with the carrier-absent system.     

Anaerobic Hydrogen Production from Sucrose Using an Acid‐Enriched Sewage Sludge Microflora

A novel and high‐rate anaerobic sequencing bath reactor (ASBR) process was used to evaluate the hydrogen productivity of an acid‐enriched sewage sludge microflora at a temperature of 35 °C. In this ASBR process a 4 h cycle, including feed, reaction, settle, and decant steps, was repeatedly performed in a 5 L reactor. The sucrose substrate concentration was 20 g COD/L; the hydraulic retention time (HRT) was maintained at 12–120 h at the initial period and thereafter at 4–12 h. The reaction/settle period ratio, which is the most important parameter for ASBR operation was 1.7. The experimental results indicated that the hydrogenic activity of the sludge microflora was HRT‐dependent and that proper pH control was necessary for a stable operation of the bioreactor. The peak hydrogenic activity value was attained at an HRT of 8 h and an organic loading rate of 80 kg COD/m³ × day. Each mole of sucrose in the reactor produced 2.8 mol of hydrogen and each gram of biomass produced 39 mmol of hydrogen per day. An overly‐short HRT might deteriorate the hydrogen productivity. The concentration ratios of butyric acid to’acetic acid, as well as volatile fatty acid and soluble microbial products to alkalinity can be used as monitoring indicators for the hydrogenic bioreactor.     

Strategies to suppress hydrogen-consuming microorganisms affect macro and micro scale structure and microbiology of granular sludge

Treatment of anaerobic granules with heat and two chemical treatments, contacting with 2-bromoethanesulfonate (BES) and with BES + Chloroform, were applied to suppress hydrogen-consuming microorganisms. Three mesophilic expanded granular sludge bed (EGSB) reactors-R(Heat), R(BES), and R(BES + Chlo)--were inoculated with the treated sludges and fed with synthetic sugar-based wastewater (5 g(COD) L(-1), HRT 20-12 h). Morphological integrity of granules and bacterial communities were assessed by quantitative image analysis and 16S rRNA gene based techniques, respectively. Hydrogen production in R(Heat) was under 300 mL H(2) L(-1) day(-1), with a transient peak of 1,000 mL H(2) L(-1) day(-1) after decreasing HRT. In R(BES + Chlo) hydrogen production rate did not exceed 300 mL H(2) L(-1) day(-1) and there was granule fragmentation, release of free filaments from aggregates, and decrease of granule density. In R(BES), there was an initial period with unstable hydrogen production, but a pulse of BES triggered its production rate to 700 ± 200 mL H(2) L(-1) day(-1). This strategy did not affect granules structure significantly. Bacteria branching within Clostridiaceae and Ruminococcaceae were present in this sludge. This work demonstrates that, methods applied to suppress H(2)-consuming microorganisms can cause changes in the macro- and microstructure of granular sludge, which can be incompatible with the operation of high-rate reactors.     

Rapid formation of hydrogen-producing granules in an anaerobic continuous stirred tank reactor induced by acid incubation

A novel approach to rapidly initiate granulation of hydrogen-producing sludge was developed in an anaerobic continuous stirred tank reactor at 37 degrees C. To induce microbial granulation, the acclimated culture was subject to an acid incubation for 24 h by shifting the culture pH from 5.5 to 2.0. The culture was resumed to pH 5.5 after the incubation and the reactor was operated at hydraulic retention times (HRTs) of 12, 6, 2, 1, and 0.5 h in sequence. Microbial aggregation took place immediately with the initiation of acid incubation and granules were developed at 114 h. No granule was observed in the absence of acid incubation in the control test. Changing the culture pH resulted in improvement in surface physicochemical properties of the culture favoring microbial granulation. The zeta potential increased from -11.6 to -3.5 mV, hydrophobicity in terms of contact angle improved from 31 degrees to 43 degrees and extracellular proteins/polysaccharides ratio increased from 0.2 to 0.5-0.8. Formation of granular sludge facilitated biomass retention of up to 32.2 g-VSS/L and enhanced hydrogen production. The hydrogen production rate and hydrogen yield increased with the reduction in HRT at an influent glucose concentration of 10 g/L once steady granular sludge layer was formed, achieving the respective peaks of 3.20 L/L x h and 1.81 mol-H(2)/mol-glucose at 0.5 h HRT. The experimental results suggested that acid incubation was able to initiate the rapid formation of hydrogen-producing granules by regulating the surface characteristics of microbial aggregates in a well-mixed reactor, which enhanced the hydrogen production.     

Operation strategies for biohydrogen production with a high-rate anaerobic granular sludge bed bioreactor

Long-term operation for biohydrogen production with an efficient carrier-induced granular sludge bed (CIGSB) bioreactor had encountered problems with poor biomass retention at a low hydraulic retention (HRT) as well as poor mass-transfer efficiency at a high HRT or under a prolonged operation period. This work was undertaken to develop strategies enabling better biomass retention and mass-transfer efficiency of the CIGSB reactors. Supplementation of calcium ion was found to enhance mechanical strength of the granular sludge. Addition of 5.4–27.2 mg/l of Ca²⁺ also led to an over three-fold increase in biomass concentration and a nearly five-fold increase in the H₂ production rate (up to 5.1 l H₂/h/l). Two reflux strategies were utilized to enhance the mass-transfer efficiency of the CIGSB system. The liquid reflux (LR) strategy enhanced the H₂ production rate by 2.2-fold at an optimal liquid upflow velocity of 1.09 m/h, which also gave a maximal biomass concentration of ca. 22 g VSS/l. Similar optimal H₂ production rate was also obtained with the gas reflux (GR) strategy at a rate of 1.0–1.49 m/h, whereas the biomass concentration decreased to 2–7 g VSS/l and thereby the specific H₂ production rate was higher than that with LR. The operation strategies applied in this work were effective to allow stable and efficient H₂ production for nearly 100 days.     

Kinetics of hydrogen production with continuous anaerobic cultures utilizing sucrose as the limiting substrate

In this study, local sewage sludge was acclimated to establish H2-producing enrichment cultures, which were used to convert sucrose to H2 with continuously stirred anaerobic bioreactors. The steady-state behaviors of cell growth, substrate utilization, and product formation were closely monitored. Kinetic models were developed to describe and predict the experimental results from the H2-producing cultures. Operation at dilution rates (D) of 0.075-0.167 h(-1) was preferable for H2 production, resulting in a H2 concentration of nearly 0.02 mol/l. The optimal hydrogen production rate was 0.105 mol/h occurring at D=0.125 h(-1). The major volatile fatty acid produced was butyric acid (HBu), while acetic acid and propionic acid were also produced in lesser quantities. The major solvent product was ethanol, whose concentration was only 15% of that of HBu, indicating that the metabolic flow favors H2 production. The proposed model was able to interpret the trends of the experimental data. The maximum specific growth rate (mu(max)), Monod constant (Ks), and yield coefficient for cell growth (Y(x/s)) were estimated as 0.172 h(-1), 68 mg COD/l, and 0.1 g/g, respectively. The model study also suggests that product formation in the continuous hydrogen-producing cultures was essentially a linear function of biomass concentration.     

Hydrogen production with immobilized sewage sludge in three-phase fluidized-bed bioreactors

Municipal sewage sludge was immobilized with a modified alginate gel entrapment method, and the immobilized cells were used to produce hydrogen gas in a three-phase fluidized bed. The hydrogen-producing fluidized beds were operated at different liquid velocity (U(0)) and hydraulic retention time (HRT). The results show that in response to operating liquid velocities, the fluidized-bed system had three flow regimes, namely, plug flow, slug flow, and free bubbling. Pressure fluctuation analysis was used to analyze the hydrodynamic properties in this three-phase fluidized bed when it was under a steady-state production of biogas. With a steady-state biogas production rate (U(g)) of 0.196 mL/s/L, a transition state occurred at a liquid velocity (U(0)) of 0.85 cm/s. As U(0) < 0.85 cm/s, the system was basically a nonhomogeneous fluidized bed, whereas the bed became homogeneous when U(0) was higher than 0.85 cm/s. The fluidized bed can be stably carried out at high loading rates (HRT as low as 2 h). Hydrogen fermentation results show that the maximal hydrogen production rate was 0.93 L/h/L and the best yield (Y(H)2(/sucrose)) was 2.67 mol H(2)/mol sucrose.     

Start‐up of Anaerobic Hydrogen Producing Reactors Seeded with Sewage Sludge

The procedure for starting‐up continuously stirred tank reactors (CSTR) for acclimating anaerobic hydrogen‐producing microorganisms with sewage sludge was investigated. Initially, feeding with glucose and sucrose as well as mixing were carried out in semicontinuous mode; hydraulic retention time (HRT) was in an order of 20, 15, 10, 5, 2.5 and 2 days. When the pH declined to its lowest value (pH 5.18), it was adjusted to 6.7 using sodium hydroxide (1 N). At the same time, the semi‐continuous operation was changed to a continuous one. Finally, the pH was continuously regulated at approximately 6.7. The results indicate that this procedure can be used to cultivate seed sludge for hydrogen production from sewage sludge resulting in a large hydrogen production in less than 60 days. When the substrate was glucose, a hydrogen yield of 1.63 mol H₂/mol glucose and a specific hydrogen production rate of 321 mmol H₂/g VSS day at an HRT of 13.3 h was achieved. When the substrate was sucrose with the same HTR, a hydrogen yield of 4.45 mol H2/mol sucrose and a specific hydrogen production rate of 707 mmol H₂/g VSS day was obtained.     

Acclimation Strategy of a Biohydrogen Producing Population in a Continuous‐Flow Reactor with Carbohydrate Fermentation

Poor startup of biological hydrogen production systems can cause an ineffective hydrogen production rate and poor biomass growth at a high hydraulic retention time (HRT), or cause a prolonged period of acclimation. In this paper a new startup strategy was developed in order to improve the enrichment of the hydrogen‐producing population and the efficiency of hydrogen production. A continuously‐stirred tank reactor (CSTR) and molasses were used to evaluate the hydrogen productivity of the sewage sludge microflora at a temperature of 35 °C. The experimental results indicated that the feed to microorganism ratio (F/M ratio) was a key parameter for the enrichment of hydrogen producing sludge in a continuous‐flow reactor. When the initial biomass was inoculated with 6.24 g of volatile suspended solids (VSS)/L, an HRT of 6 h, an initial organic loading rate (OLR) of 7.0 kg chemical oxygen demand (COD)/(m³ × d) and an feed to microorganism ratio (F/M) ratio of about 2–3 g COD/(g of volatile suspended solids (VSS) per day) were maintained during startup. Under these conditions, a hydrogen producing population at an equilibrium state could be established within 30 days. The main liquid fermentation products were acetate and ethanol. Biogas was composed of H₂ and CO₂. The hydrogen content in the biogas amounted to 47.5 %. The average hydrogen yield was 2.01 mol/mol hexose consumed. It was also observed that a special hydrogen producing population was formed when this startup strategy was used. It is supposed that the population may have had some special metabolic pathways to produce hydrogen along with ethanol as the main fermentation products.     

Performance evaluation of an anoxic/oxic activated sludge system: effects of mean cell residence time and anoxic hydraulic retention time

A laboratory investigation has been undertaken to asses the effects of two operating parameters, mean cell residence time (MCRT) and anoxic hydraulic retention time (HRT), on the performance of an anoxic/oxic activated sludge system. The performance of the system was evaluated in terms of its COD, nitrogen, and biomass characteristics. An activated sludge system is capable of producing a better effluent, in terms of COD and nitrogen characteristics, when it is operated in an anoxic/oxic fashion. A longer MCRT and an adequate anoxic HRT are desirable in the operation of an anoxic/oxic activated sludge system. For the wastewater used in this investigation, the anoxic/oxic unit was capable of producing an effluent with the following characteristics when it was operated at MCRT = 20 days, total system HRT = 10 h, and anoxic HRT = 3-5 h: COD = 15 mg/L; VSS = 10 mg/L; TKN = 1.30 mg/L; NH(3) - N = 0.60 mg/L; and NO(2) + NO(3) - N = 5.0 mg/L. A uniform distribution of biomass is achievable in an anoxic/oxic activated sludge system because of the intensive recirculation/convection maintained. The provision of an anoxic zone in the aeration tank promotes a rapid adsorption of feed COD into the biomass without an immediate utilization for cell synthesis. This, in turn, results in a high microbial activity and a lower observed biomass yield in the system. A tertiary treatment efficiency is achievable in an anoxic/oxic activated sludge system with only secondary treatment operations and costs. A conventional activated sludge system can be easily upgraded by converting to the anoxic/oxic operation with minor process modifications.     

Performance characteristics of a two-stage dark fermentative system producing hydrogen and methane continuously

The performance of a mesophilic two-stage system generating hydrogen and methane continuously from sucrose (10-30 g/L) was investigated. A hydrogen-generating CSTR followed by an upflow anaerobic filter were both inoculated with anaerobically digested sewage sludge, and ORP, pH, gas output, %H(2), %CH(4) and %CO(2) monitored. pH was controlled with NaOH, KOH or Ca(OH)(2). Using NaOH as alkali with 10 g/L sucrose, yields of 1.62 +/- 0.2 mol H(2)/mol hexose added and 323 mL CH(4)/gCOD added to the hydrogen and methane reactors respectively were achieved. The overall chemical oxygen demand (COD) reduction was 92.6% with 0.90 +/- 0.1 g/L sodium and 316 +/- 40 mg/L residual acetate in the methane reactor. Operation at 20 g/L sucrose and NaOH as alkali led to impaired volatile fatty acid (VFA) degradation in the methane reactor with 2.23 +/- 0.2 g/L sodium, 1,885 mg/L residual acetate, a hydrogen yield of 1.47 +/- 0.1 mol/mol hexose added, a methane yield of 294 mL/gCOD added and an overall COD reduction of 83%. Using Ca(OH)(2) as alkali with 20 g/L sucrose gave a hydrogen yield of 1.29 +/- 0.3 mol/mol hexose added, a methane yield of 337 mL/gCOD added and improved the overall COD reduction to 91% with residual acetate concentrations of 522 +/- 87 mg/L. Operation at 30 g/L sucrose with Ca(OH)(2) gave poorer overall COD reduction (68%), a hydrogen yield of 1.47 +/- 0.2 mol/mol hexose added, a methane yield of 138 mL/gCOD added and residual acetate 7,343 +/- 715 mg/L. It was shown that sodium toxicity and overloading are important issues for successful anaerobic digestion of effluent from biohydrogen reactors in high rate systems.     

Influence of substrate concentration on the stability and yield of continuous biohydrogen production

The effect of substrate concentration (sucrose) on the stability and yield of a continuous fermentative process producing hydrogen was studied. High substrate concentrations are attractive from an energy standpoint as they would minimise the energy required for heating. The reactor was a CSTR; temperature was maintained at 35 degrees C; pH was controlled between 5.2 and 5.3, and the hydraulic retention time (HRT) was 12 h. Online measurements were taken for ORP, pH, temperature, %CO2, gas output and %H2, and data logged using a MatLAB data acquisition toolbox. Steady-state operation was obtained at 10, 20 and 40 g/L of sucrose in the influent, but a subsequent step change to 50 g/L was unsustainable. The hydrogen content ranged between 50% and 60%. The yield of hydrogen decreased as the substrate concentration increased from 1.7 +/- 0.2 mol/mol hexose added at 10 g/L, to 0.8 +/- 0.1 mol/mol at 50 g/L. Sparging with nitrogen improved the hydrogen yield by at least 35% at 40 g/L and at least 33% at 50 g/L sucrose. Sparging also enabled steady-state operation at 50 g/L sucrose. Addition of an extra 4 g/L of n-butyric acid to the reactor operating at 40 g/L sucrose increased the butyrate concentration from 9,830 to 18,900 mg/L, immediately stopping gas production and initiating the production of propionate, whilst the addition of 2 g/L taking the butyrate concentration to 12,200 mg/L did not do so. It was shown that operation at 50 g/L sucrose in a CSTR in butyrate fermentation is possible.     

Biohydrogen production in a three-phase fluidized bed bioreactor using sewage sludge immobilized by ethylene–vinyl acetate copolymer

Ethylene–vinyl acetate (EVA) copolymer was used to immobilize H₂-producing sewage sludge for H₂ production in a three-phase fluidized bed reactor (FBR). The FBR with an immobilized cell packing ratio of 10% (v/v) and a liquid recycle rate of 5 l/min (23% bed expansion) was optimal for dark H₂ fermentation. The performance of the FBR reactor fed with sucrose-based synthetic medium was examined under various sucrose concentration (C_so) and hydraulic retention time (HRT). The best volumetric H₂ production rate of 1.80 ± 0.02 H₂ l/h/l occurred at C_so = 40 g COD/l and 2 h HRT, while the optimal H₂ yield (4.26 ± 0.04 mol H₂/mol sucrose) was obtained at C_so = 20 g COD/l and 6 h HRT. The H₂ content in the biogas was stably maintained at 40% or above. The primary soluble metabolites were butyric acid and acetic acid, as both products together accounted for 74–83% of total soluble microbial products formed during dark H₂ fermentation.     

The inhibitory effects and removal of dieldrin in continuous upflow anaerobic sludge blanket reactors

The inhibitory effects and removal efficiency of dieldrin (DLD) in anaerobic reactors were investigated. Anaerobic toxicity assay (ATA) experiments conducted in batch reactors revealed that 30 mg/l DLD had inhibitory effects on the unacclimated mixed anaerobic cultures. Continuous reactor experiments performed in a lab-scale two-stage upflow anaerobic sludge blanket (UASB) reactor system which was fed with ethanol as the sole carbon source, indicated that anaerobic granular cultures could be successfully acclimated to DLD. Chemical oxygen demand (COD) removal efficiencies were 88-92% for the two-stage system. The influent DLD concentration of 10 mg/l was removed by 44-86% and 86-94% in the second stage and overall UASB system, respectively. Biosorption of DLD on granular anaerobic biomass was found to be a significant mechanism for DLD removal in the UASB system. The maximum DLD loading rate and minimum HRT achievable for the first stage UASB reactor were 0.5 mg/lday (76 microg DLD/g VSS.day) and 10 h, respectively, which resulted in the overall COD removal efficiency of 85%.     

实验室模拟高负荷SPAC厌氧反应器运行

采用模拟废水, 对新型高负荷螺旋式自循环(Spiral automatic circulation, SPAC)厌氧反应器的运行性能进行了实验室模拟研究。结果表明: 在30oC, 水力停留时间(HRT)为12 h, 进水COD浓度从8000 mg/L升至20 000 mg/L的条件下, 反应器的COD去除率为91.1%~95.7%, 平均去除率为93.6％。在进水浓度为20 000 mg/L, HRT由5.95 h缩短至1.57 h的工况下, COD去除率从96.0%降低至78.7%, 反应器达到最高容积负荷率306 g COD/(L·d), 最大容积COD去除率240 g/(L·d), 最高容积产气率131 L/(L·d)。该反应器对基质浓度的连续提升具有良好的适应能力。进水COD浓度由8000 mg/L提升至20 000 mg/L时, 出水COD浓度一直处在较低水平(平均为852?mg/L), 容积COD去除率和容积产气率分别提高162%和119%。该反应器对HRT的连续缩短也有良好的适应能力。HRT由5.95 h缩短至1.57 h时,反应器容积COD去除率和容积产气率分别升高191%和195%。     

Aerobic granulation with brewery wastewater in a sequencing batch reactor

Aerobic granular sludge was cultivated in a sequencing batch reactor fed with brewery wastewater. After nine-week operation, stable granules with sizes of 2-7 mm were obtained. With the granulation, the SVI value decreased from 87.5 to 32 mL/g. The granular sludge had an excellent settling ability with the settling velocity over 91 m/h. Aerobic granular sludge exhibited good performance in the organics and nitrogen removal from brewery wastewater. After granulation, high and stable removal efficiencies of 88.7% COD(t), 88.9% NH(4)(+)-N were achieved at the volumetric exchange ratio of 50% and cycle duration of 6h. The average COD(t) and COD(s) of the effluent were 212 and 134 mg/L, respectively, and the average effluent ammonium concentration was less than 14.4 mg/L. Nitrogen was removed due to nitrification and simultaneous denitrification in the inner core of granules.     

Kinetic behaviour of waste tyre rubber as microorganism support in an anaerobic digester treating cane molasses distillery slops

The kinetics of anaerobic digestion of cane molasses distillery slops was investigated using a continuous-flow bioreactor which contained waste tyre rubber as support, to which the microorganisms became immobilized. Hydraulic retention times (HRT) ranging from 1 to 10 days were investigated at an average influent chemical oxygen demand (COD) concentration of 47.7?g/l. The maximum substrate utilization rate, k, and half saturation coefficient, K _L, were determined to be 1.82?kg COD_removed/kg VSS day and 0.33?kg COD/kg VSS day. The yield coefficient, Y, and sludge decay rate coefficient, K _d, were also determined to be 0.06?kg VSS/kg COD_removed and 0.05?day^-1, respectively. Methane production was maximum (6.75?l/l day) at a 2 day HRT corresponding to a biomass loading rate of 2.578?kg COD/kg VSS day. Biogas yield ranged between 0.51?l/g COD (HRT=2 days) and 0.25?l/g COD (HRT=1?day). In addition, the methane percentage in the biogas varied between 70.5% (HRT=10?days) and 47.5% (HRT=1?day). The close relationship between biomass loading rate and specific substrate utilization rate supported the use of Monod equations. Finally, the experimental values of effluent substrate concentration were reproduced with deviations equal to or less than 10% in every case.     

Performance of an upflow anaerobic reactor combining a sludge blanket and a filter treating sugar waste

A new hybrid reactor, the upflow blanket filter (UBF), which combined on open volume in the bottom two-thirds of the reactor for a sludge blanket and submerged plastic rings (Flexiring, Koch Inc., 235 m(2)/m(3)) in the upper one-third of the reactor volume, was studied. This UBF reactor was operated at 27 degrees C at loading rates varying from 5 to 51 g chemical oxygen demand (COD)/L d with soluble sugar wastewater (2500 mg COD/L). Maximum removal rates of 34 g COD/L d and CH(4) production rates of 7 vol/vol d [standard temperature and pressure (STP)] were obtained. The biomass activity was about 1.2 g COD/g volatile suspended solids per day. Conversion (based on effluent soluble COD) was over 93% with loading rates up to 26 g COD/L d. At higher loading rates conversion decreased rapidly. The packing was very efficient in retaining biomass.     

Electricity generation from young landfill leachate in a microbial fuel cell with a new electrode material

This study aims at evaluating the performance of a two-chambered continuously fed microbial fuel cell with new Ti–TiO₂ electrodes for bioelectricity generation from young landfill leachate at varying strength of wastewater (1–50 COD g/L) and hydraulic retention time (HRT, 0.25–2 days). The COD removal efficiency in the MFC increased with time and reached 45 % at full-strength leachate (50 g/L COD) feeding. The current generation increased with increasing leachate strength and decreasing HRT up to organic loading rate of 100 g COD/L/day. The maximum current density throughout the study was 11 A/m² at HRT of 0.5 day and organic loading rate of 67 g COD/L/day. Coulombic efficiency (CE) decreased from 57 % at feed COD concentration of 1 g/L to less than 1 % when feed COD concentration was 50 g/L. Increase in OLR resulted in increase in power output but decrease in CE.