Comparison of Rhizopus nigricans in a pelleted growth form with some other types of waste microbial biomass as biosorbents for metal ions

Biosorption of metal ions (Li⁺, Ag⁺, Pb²⁺, Cd²⁺, Ni²⁺, Zn²⁺, Cu²⁺, Sr²⁺, Fe²⁺, Fe³⁺ and Al³⁺) by Rhizopus nigricans biomass was studied. It was shown that metal uptake is a rapid and pH-dependent process, which ameliorates with increasing initial pH and metal concentrations. Different adsorption models: Langmuir, Freundlich, split-Langmuir and combined nonspecific-Langmuir adsorption isotherm were applied to correlate the equilibrium data. The maximum biosorption capacities for the individual metal ions were in the range from 160 to 460 mol/g dry weight. Scatchard transformation of equilibrium data revealed diverse natures of biomass metal-binding sites. The binding of metals was also discussed in terms of the hard and soft acids and bases principle. The maximum biosorption capacities and the binding constant of R. nigricans were positively correlated with the covalent index of metal ions.The following types of waste microbial biomass originating as by-products from industrial bioprocesses were tested for biosorption of metal ions: Aspergillus terreus, Saccharomyces cerevisiae, Phanerochaete chrysosporium, Micromonospora purpurea, M. inyoensis and Streptomyces clavuligerus. The determined maximum biosorption capacities were in the range from 100 to 500 mol/g dry weight. The biosorption equilibrium was also represented with Langmuir and Freundlich sorption isotherms.     

Removal of Cd2+, Pb2+, and Zn2+ from contaminated water using dolomite powder

Dolomite collected from Surat Thani Province in Thailand was investigated for use as a sorbent for the removal of divalent heavy metal cations from an aqueous solution. The sorbent had a surface area of 2.46 m²/g and a pH of zero point charge (pHzpc) of 9.2. Batch sorption was used to examine the effect of the pH (pH 3–7) on the sorption capacity of Cd²⁺, Pb²⁺ and Zn²⁺, alone or together as an equimolar mixture at various concentrations. Alone, each heavy metal cation was adsorbed faster at a higher pH, where the sorption of Cd²⁺ and Pb²⁺ fitted a Langmuir isotherm, but Zn²⁺ sorption best fitted a Freundlich isotherm. Under equimolar competitive sorption, the sorption capacity of each cation was decreased by 75.8% (0.29–0.07 mM/g), 82.8% (0.53–0.09 mM/g), and 95.7% (0.84–0.04 mM/g) for Cd²⁺, Pb²⁺ and Zn²⁺, respectively, compared to that with the respective single cation. Desorption of these heavy metal cations from dolomite was low, with an average desorption level of 0.06–17.4%. Furthermore, since dolomite is readily available and rather cheap, it is potentially suitable for use as an efficient sorbent to sorb Cd²⁺ and Pb²⁺, and perhaps Zn²⁺, from contaminated water.     

Biosorption with Algae: A Statistical Review

ABSTRACT

The state of the art in the field of biosorption using algae as biomass is reviewed. The available data of maximum sorption uptake (q_max) and biomass-metal affinity (b) for Cd^{2 +}, Cu^{2 +}, Ni^{2 +}, Pb^{2 +} and Zn^{2 +} were statistically analyzed using 37 different algae (20 brown algae, 9 red algae and 8 green algae). Metal biosorption research with algae has used mainly brown algae in pursuit of treatments, which improve its sorption uptake. The information available in connection with multimetallic systems is very poor. Values of q_max were close to 1 mmol/g for copper and lead and smaller for the other metals. Metal recovery performance was worse for nickel and zinc, but the number of samples for zinc was very small. All the metals except lead present a similar affinity for brown algae. The difference in the behavior of lead may be due to a different uptake mechanism. Brown algae stand out as very good biosorbents of heavy metals. The best performer for metal biosorption is lead.     

Zn2+ biosorption by Oscillatoria anguistissima

Oscillatoria anguistissima showed a very high capacity for Zn²⁺ biosorption (641 mg g⁻¹ dry biomass at a residual concentration of 129·2 ppm) from solution and was comparable to the commmercial ion-exchange resin IRA-400C. Zn²⁺ biosorption was rapid, pH dependent and temperature independent phenomenon. Zn²⁺ adsorption followed both Langmuir and Freundlich models. The specific uptake (mg g⁻¹ dry biomass) of metal decreased with increase in biomass concentration. Pretreatment of biomass did not significantly affect the biosorption capacity of O. anguistissima. The biosorption of zinc by O. anguistissima was an ion-exchange phenomenon as a large concentration of magnesium ions were released during zinc adsorption. The zinc bound to the biomass could be effectively stripped using EDTA (10 mM) and the biomass was effectively used for multiple sorption–desorption cycles with in-between charging of the biomass with tap water washings. The native biomass could also efficiently remove zinc from effluents obtained from Indian mining industries.     

Competitive adsorption of Pb, Cd and Zn ions onto Eichhornia crassipes in binary and ternary systems

A batch sorption technique was used to study the biosorption of Pb²⁺, Cd²⁺ and Zn²⁺ ions onto the vastly abundant water hyacinth weed, Eichhornia crassipes biomass in binary and ternary systems at a temperature of 30 °C and pH 4.84. Mutual interference effects were probed using equilibrium adsorption capacity ratios, , where the prime indicates the presence of one or two other metal ions. The combined action of the metals was found to be antagonistic, and the metal sorption followed the order Pb²⁺  Cd²⁺  Zn²⁺. The behaviour of competitive biosorption for Pb–Cd and Pb–Zn combinations were successfully described by the Langmuir Competitive Model (CLM), whilst the model showed poor fitting to the Cd–Zn data. In conclusion, Pb²⁺ ions could still be effectively removed from aqueous solution in the presence of both Cd²⁺ and Zn²⁺ ions, but removal of the Cd²⁺ and Zn²⁺ ions would be suppressed in the presence of Pb²⁺.     

Cadmium binding characterization and mechanism of a newly isolated strain Cystobasidium oligophagum QN-3

The aim of this study was to screen a strain for the removal of Cd²⁺ from aqueous solution and investigate the characterization and mechanism of the Cd²⁺ binding process. A novel strain of yeast showed high tolerance of cadmium, namely Cystobasidium oligophagum QN-3, was isolated from soils, which could resist 22,000 mg/L and 18,000 mg/L Cd²⁺ on PDA (potato dextrose agar) plate and in PDA liquid medium, respectively. Cd²⁺ binding experiment showed that the strain could remove Cd²⁺ from aqueous solution effectively, the maximum Cd²⁺ removal rate of 84.45% was achieved at initial Cd²⁺ concentration 30 mg/L. Scanning electron microscopy (SEM) analysis revealed that sorption of Cd²⁺ by cells could be associated with changes in the cell surface morphology. Fourier transform-infrared spectroscopy (FTIR) analysis confirmed the important role of the functional groups  OH, CO,  NH₂, COO , PO, and CH on the cell surface in the binding of Cd²⁺. The comparison of the binding ability of different cellular parts indicated a significant role of the cell wall played in the Cd²⁺ binding process. Pretreatment of the cells by boiling or ultrasonication could improve the biosorption capacity of QN-3. In addition, QN-3 exhibited selective and preferential property of binding capacity for other heavy metals, such as Pb²⁺, Cu²⁺, Cd²⁺, Zn²⁺, and Ni²⁺. These data suggested the promising use of Cystobasidium oligophagum QN-3 as an effective and friendly biosorbent for cadmium or other heavy metals decontamination in the environment.     

Biosorption of Heavy Metals (Cd2+, Cu2+, Co2+, and Mn2+) by Thermophilic Bacteria,Geobacillus thermantarcticus and Anoxybacillus amylolyticus: Equilibrium and Kinetic Studies

ABSTRACT

Two strains of thermophilic bacteria, Geobacillus thermantarcticus and Anoxybacillus amylolyticus, were employed to investigate the biosorption of heavy metals including Cd²⁺, Cu²⁺, Co²⁺, and Mn²⁺ ions. The effects of different biosorption parameters such as pH (2.0–10.0), initial metal concentrations (10.0–300.0 mg L^?1), amount of biomass (0.25–10 g L^?1), temperature (30–80°C), and contact time (15–120 min) were investigated. Concentrations of metal ions were determined by using an inductively coupled plasma optical emission spectrometry (ICP-OES). Optimum pHs for Cd²⁺, Cu²⁺, Co²⁺, and Mn²⁺ biosorption by Geobacillus thermantarcticus were found to be 4.0, 4.0, 5.0, and 6.0, respectively. For Anoxybacillus amylolyticus, the optimum pHs for Cd²⁺, Cu²⁺, Co²⁺, and Mn²⁺ biosorption were found to be 5.0, 4.0, 5.0, and 6.0, respectively. The Cd²⁺, Cu²⁺, Co²⁺, and Mn²⁺ removals at 50 mg L^?1 in 60 min by 50 mg dried cells of Geobacillus thermantarcticus were 85.4%, 46.3%, 43.6%, and 65.1%, respectively, whereas 74.1%, 39.8%, 35.1%, and 36.6%, respectively, for Anoxybacillus amylolyticus. The optimum temperatures for heavy metal biosorption were near the optimum growth temperatures for both strains. Scatchard plot analysis was employed to obtain more compact information about the interaction between metal ions and biosorbents. The plot results were further studied to determine if they fit Langmuir and Freundlich models.     

Characterization of cadmium removal by Rhodotorula sp. Y11

Experiments were conducted studying the removal of Cd²⁺ from water via biosorption using Rhodotorula sp. Y11. The effects of temperature and initial pH of the solution on biosorption were studied. Caustic and heat treatments showed different influences on the biosorption capacity, and the highest metal uptake value (19.38 mg g⁻¹) was obtained by boiling treated yeast cells. The presence of competing cations, such as Ag⁺, Cu²⁺, and Mg²⁺, except Na⁺ ions, significantly interfered with the metal uptake. Results indicate that the Langmuir model gave a better fit to the experimental data than the Freundlich equation. The q ₁₀ value was 11.38 mg g⁻¹ for Cd²⁺ uptake by Y11. Chemical modifications of the biomass demonstrated that carboxyl and amide groups play an important role in Cd²⁺ biosorption.     

Repeated removal of cadmium and zinc from an industrial effluent by waste biomass Sargassum sp.

Waste biomass Sargassum sp. biosorbed 100% of Cd²⁺ and 99.4% of Zn²⁺ from a 3 and 98 mg l^–1 solution (pH 4.5), respectively, at the end of four serial experiments. Of the five desorbents studied in consecutive adsorption/desorption cycles, CaCl₂ 0.05 M eluted nearly 40% of both metals and decreased the biosorption in only 8% and 17% of Cd²⁺ and Zn²⁺, respectively. Although NaOH desorbent improved the heavy metal uptake from the second cycle onwards, it did not elute metals from the pre-loaded biomass.     

Enhanced heavy metal removal from waste water by viable, glucose pretreated Saccharomyces cerevisiae cells

Summary The bioaccumulation of metals (Cu²⁺, Cr⁶⁺, Cd²⁺, Ni²⁺ and Zn²⁺) from three electroplating effluents by viable Saccharomyces cerevisiae, and the effect of glucose treatment on accumulation was determined. Pretreatment of the yeast cells with glucose increased the amount of metal removed, whilst direct addition of glucose to the yeast-effluent solution had no effect on the amount of metal accumulated.     

Characterization of Desmodesmus pleiomorphus isolated from a heavy metal-contaminated site: biosorption of zinc

Microalgae have been proven efficient biological vectors for heavy metal uptake. In order to further study their biosorption potential, a strain of Desmodesmus pleiomorphus (L) was isolated from a strongly contaminated industrial site in Portugal. Under different initial Zn²⁺ concentrations, metal removal by that strain reached a maximum of 360 mg Zn/g biomass after 7 days, at 30 mg Zn/l, after an initial rapid phase of uptake. Comparative studies were carried out using a strain of the same microalgal species that is commercially available (ACOI 561): when exposed to 30 mg Zn/l, it could remove only 81.8 mg Zn/g biomass. Biosorption experiments using inactivated biomass of the isolated strain reached a maximum Zn²⁺ uptake of 103.7 mg/g. Metal removal at various initial pH values was studied as well; higher removal was obtained at pH 5.0. The microalga strain L, isolated from the contaminated site, exhibited a much higher removal capacity than the commercial strain, and the living biomass yielded higher levels of metal removal than its inactivated form.     

Heterologous Expression and Metal-Binding Characterization of a Type 1 Metallothionein Isoform (OsMTI-1b) from Rice (Oryza sativa)

Metallothioneins (MTs) are ubiquitous, low molecular mass and cysteine-rich proteins that play important roles in maintaining intracellular metal homeostasis, eliminating metal toxification and protecting the cells against oxidative damages. MTs are able to bind metal ions through the thiol groups of their cysteine residues. Plants have several MT isoforms which are classified into four types based on the arrangement of cysteine residues. In the present study, a rice (Oryza sativa) gene encoding type 1 MT isoform, OsMTI-1b, was inserted in vector pET41a and overexpressed in Escherichia coli as carboxy-terminal extensions of glutathione-S-transferase (GST). The recombinant protein GST-OsMTI-1b was purified using affinity chromatography and its ability to bind with Ni²⁺, Cd²⁺, Zn²⁺ and Cu²⁺ ions was analyzed. The results demonstrated that this isoform has ability to bind Ni²⁺, Cd²⁺ and Zn²⁺ ions in vitro, whereas it has no substantial ability to bind Cu²⁺ ions. From competitive reaction with 5,5′-dithiobis(2-nitrobenzoic acid), DTNB, the affinity of metal ions for recombinant form of GST-OsMTI-1b was as follows: Ni²⁺/Cd²⁺ > Zn²⁺ > Cu²⁺     

Effect of shock-loading of heavy metals on total organic carbon and phosphate removal in an anaerobic-aerobic activated sludge process

The effect of shock-loading of zinc, copper and cadmium ions on the removal of total organic carbon (TOC) and phosphate in an anaerobic-aerobic activated sludge process was investigated. TOC removal was not sensitive to shock-loading of Zn²⁺ and Cd²⁺ ions, and complete removal was achieved even at 20 mg Zn²⁺/l and 20 mg Cd²⁺/l. However, with over 1 mg Cu²⁺/1 TOC removal efficiency decreased. PO _inf4 ^sup3- removal, in contrast, was extremely sensitive to these metal ions, with the threshold being 1 mg Zn²⁺/l and 1 mg Cd²⁺/l. Higher concentrations adversely affected PO _inf4 ^sup3- removal. Copper again proved detrimental; no PO _inf4 ^sup3- removal was achieved even at 1 mg Cu/l. These results highlight the sensitivity of the removal efficiencies of TOC and PO _inf4 ^sup3- to shock loadings of these heavy metals.Y.P. Ting is with the Department of Chemical Engineering, National University of Singapore, Kent Ridge, 0511, Singapore; H. Imai and S. Kinoshita are with the Department of Chemical Process Engineering, Hokkaido University, Sapporo 060, Japan.     

The interaction of zinc, nickel and cadmium with serum albumin and histidine-rich glycoprotein assessed by equilibrium dialysis and immunoadsorbent chromatography

Human serum albumin (HSA) has been shown to bind 2–3 mol of Zn²⁺, Ni²⁺, or Cd²⁺ per mole of protein with apparent dissociation constants (K_d) in the range of 10 μm. Rabbit histidine-rich glycoprotein (HRG) binds 13, 9, and 6 mol of Zn²⁺, Ni²⁺, and Cd²⁺ per mole of protein, respectively, with apparent K_ds also near 10 μm. However, the binding of metals by HRG exhibits positive cooperativity, so that the apparent K_ds may underestimate HRGs true affinity for metal ions. The relative affinities of HSA and HRG for metal ions were found to be Zn²⁺ > Ni²⁺ > Cd²⁺. In addition, histidine (a serum metal chelator) affected the binding of Ni²⁺ by both proteins but not that of Zn²⁺ or Cd²⁺. At physiological concentrations of HSA (250 μm), HRG (2.5 μm), and histidine (100 μm), HRG bound 36% of the Zn²⁺, 9% of the Ni²⁺, and 13% of the Cd²⁺ at a total metal concentration of 25 μm. Under the same conditions HSA held 37% of the Zn²⁺, 14% of the Ni²⁺, and 56% of the Cd²⁺. Thus, HSA appears to have a lower intrinsic affinity for the three metals than HRG but would be expected to bind a higher proportion of these metals in serum. A specific immunoadsorbent column was prepared and used to study the metal binding by HRG in serum directly. Both ⁶⁵Zn²⁺ and ⁶³Ni²⁺ were associated with HRG in aliquots of rabbit serum after incubation with the corresponding metal ion. This evidence indicates that HRG must be considered as a metal binding component of serum.     

Sorption of heavy metals by four basidiomycetous fungi

Biosorptions of Pb²⁺, Cr⁶⁺, Cd²⁺ and Ni²⁺ were investigated, with special emphasis on the first one, using live and dead fungal mycelia. Of the four fungi, namely Polyporus ostreiformis, Volvariella volvacea, Pleurotus sajor-caju and Phanerochaete chrysosporium, the last one was found to be most effective in Pb²⁺ removal. Total biosorption was effected in 6 days up to the Pb²⁺ concentration of 6 mg/l, with a specific uptake of 1.33 mg Pb²⁺/g dry cell mass. The removal of other three metals varied between 28.8–73.3% from a medium containing 4 mg/l of each of the metals.Laboratory facilities created under M.Tech programme in Biotechnology and Engineering (sponsored by Department of Biotechnology, Govt. of India) were partly utilized for this study.     

Sorption of Heavy Metal Cations by Corn Mitochondria and the Effects on Electron and Energy Transfer Reactions

The passive sorption of Pb⁺², Cd⁺², Zn⁺², Co⁺², Ni⁺², and Mn⁺² by isolated corn mitochondria was determined, and, except for Pb⁺², the maximum sorption for each cation was about 58 nmol per milligram of protein. Sorption of Pb⁺² was apparently ten times greater, but precipitation may have been the cause of this larger value. The effects of Pb⁺², Cd⁺², Zn⁺², Co⁺², and Ni⁺² on acceptorless rates of electron transport for three substrates were determined. Greater than 50% inhibitions of oxidation were observed for succinate after additions of >0.1 mM Cd⁺², Zn⁺², or Pb⁺²: for NADH after additions of >0.5 mM Cd⁺² or Zn⁺²; and for malate + pyruvate after additions of >0.1 mM Cd⁺². Some inhibition of the rate of substrate oxidation was observed for most cations at higher concentrations. Coupling, as measured by ADP/O ratios, was inhibited at lowest concentrations by Cd⁺² or Zn⁺² and at higher concentrations by Co⁺² or Ni⁺². Substantial swelling of mitochondria oxidizing succinate was observed following additions of O.1 mM Cd⁺² or Pb⁺², Correlations are drawn between the effects of Pb⁺², Cd⁺², Zn⁺², Co⁺², and Ni⁺² and their sorption to mitochondrial membranes.     

Biosorption of metal ions byAzotobacter vinelandii

Azotobacter vinelandii was better than eitherDerxia gummosa orRhizobium trifolii for sorption of UO ₂ ²⁺ . Its maximum binding capacity was 0.25 mmol UO ₂ ²⁺ /g dry biomass with an affinity constant of 333 l/mmol at pH 4.1 according to the Langmuir model. In a semisynthetic medium,A. vinelandii showed the highest sorption capacity in the early stationary phase. The binding of UO ₂ ²⁺ , Cu²⁺, Ca²⁺ and Zn²⁺ was affected by the pH of the solution. With HCl as eluent, virtually all the sorbed UO ₂ ²⁺ was released. The presence of Cu²⁺, Cd²⁺, Ca²⁺, and Zn²⁺ inhibited the UO ₂ ²⁺ biosorption whereas Mg²⁺ and K⁺ had no effect.     

Heavy metal uptake capacities by the common freshwater green alga Cladophora fracta

Macroalgae have received much attention for heavy metal removal in treatment of domestic wastewater. In this report, the uptake capacity of a common freshwater green alga, Cladophora fracta, for heavy metal ions (copper, zinc, cadmium, and mercury) was evaluated. The equilibrium adsorption capacities were 2.388?mg Cu²⁺, 1.623?mg Zn²⁺, 0.240?mg Cd²⁺, and 0.228?mg Hg²⁺ per gram of living algae at 18°C and pH?5.0. The removal efficiency for Cu²⁺, Zn²⁺, Cd²⁺, and Hg²⁺ were 99, 85, 97, and 98%, respectively. Greater removal efficiency was achieved when the concentrations of metal ions were at very low level. The results indicated that living algae are suitable for removal and recovery of heavy metal ions from aqueous solutions and can be a potential tool to treat industrial wastewater.     

Use of the microalga Scenedesmus obliquus to remove cadmium cations from aqueous solutions

The ability of a wild strain of Scenedesmus obliquus, isolated from a heavy metal-contaminated environment, to remove Cd²⁺ from aqueous solutions was studied at several initial concentrations. Viable biomass removed metal to a maximum extent of 11.4 mg_Cd/g at 1 mg_Cd/l, with most Cd²⁺ being adsorbed onto the cell surface. A commercially available strain (ACOI 598) of the same microalga species was also exposed to the same Cd concentrations, and similar results were obtained for the maximum extent of metal removal. Heat-inactivated cells removed a maximum of 6.04 mg_Cd/g at 0.5 mg_Cd/l. The highest extent of metal removal, analyzed at various pH values, was 0.09 mg_Cd/g at pH 7.0. Both strains of the microalga tested have proven effective in removing a toxic heavy metal from aqueous solutions, hence supporting their choice for bioremediation strategies of industrial effluents.