Microbial biomass production from rice straw hydrolysate in airlift bioreactors

Rice straw is a by-product of rice production, and a great bioresource as raw biomass material for manufacturing value-adding protein for animal feedstock, which has been paid more and more attention. In the present work, utilizing rice straw hydrolysate as a substrate for microbial biomass production in 11.5L external-loop airlift bioreactors was investigated. Rice straw hydrolysate obtained through acid-hydrolyzing rice straw was used for the culture of yeast Candida arborea AS1.257. The influences of gas flow rate, initial liquid volume, hole diameter of gas sparger and numbers of sieve plates on microbial biomass production were examined. The best results in the external-loop airlift bioreactor were obtained under 9.0 L initial liquid volume, 1.1 (v/v)/min gas flow rate during culture time of 0-24 h and 1.4 (v/v)/min gas flow rate of 24-48 h at 29+/-1 degrees C. The addition of the sieve plates in the riser of the external-loop airlift bioreactor increased productivity. After 48 h, under optimized operation conditions, crude protein productivity with one sieve and two sieves were 13.6 mg/mL and 13.7 mg/mL, respectively, comparing 12.7 mg/mL without sieves in the airlift bioreactor and 11.7 mg/mL in the in the 10-L mechanically stirred tank bioreactor. It is feasible to operate the external-loop airlift bioreactors and possible to reduce the production cost for microbial biomass production from the rice straw hydrolysate.     

A two‐phase partitioning airlift bioreactor for the treatment of BTEX contaminated gases

This investigation characterizes a novel 11 L airlift two‐phase partitioning bioreactor (TPPB) for the treatment of gases contaminated with a mixture of benzene, toluene, ethylbenzene, and o‐xylene (BTEX). The application of the TPPB technology in an airlift bioreactor configuration provides a novel technology that reduces energy intensity relative to traditional stirred tank TPPB configurations. The addition of a solid second phase of silicone rubber beads (10%, v/v) or of a liquid second phase of silicone oil (10%, v/v) resulted in enhanced performance of the airlift bioreactor relative to the single phase case, with 20% more BTEX being removed from the gas phase during an imposed transient loading. During a 4 h loading step change of three times the nominal loading (60 g m^?3 h^?1), overall removal efficiencies for the airlift TPPBs containing a liquid or solid phase remained above 75%, whereas the single phase airlift had an overall removal efficiency of 47.1%. The airlift TPPB containing a silicone rubber second phase was further characterized by testing performance during steady‐state operation over a range of loadings and inlet gas flow rates in the form of a 3² factorial experimental design. Optimal operating conditions that avoid oxygen limitations and that still have a slow enough gas flow rate for sufficient BTEX transfer from the gas phase to the working volume are identified. The novel solid–liquid airlift TPPB reduces energy inputs relative to stirred tank designs while being able to eliminate large amounts of BTEX during both steady‐state and fluctuating loading conditions. Biotechnol. Bioeng. 2009;103: 1077–1086. © 2009 Wiley Periodicals, Inc.     

Analysis of petroleum biodesulfurization in an airlift bioreactor using response surface methodology

For the first time, growing cells of Gordonia alkanivorans RIPI90A were used for biodesulfurization (BDS) of diesel. This process was carried out in an internal airlift bioreactor. BDS parameters (oil/water phase ratio and initial sulfur concentration) were optimized in flasks using response surface methodology. Predicted results were found to be in good agreement with experimental results. Initial sulfur concentration had a remarkable effect on BDS process. Maximum removal of sulfur (21 mg/l) can be achieved at oil/water phase ratio of 25% (v/v) and initial sulfur concentration of 28 mg/l. Moreover, effect of superficial gas velocity (Ug) and working volume (v) on volumetric gas liquid mass transfer coefficient was studied in an airlift bioreactor for BDS of diesel. The best results were achieved at Ug and v of 2.5l/min and 6.6l, respectively. Subsequently, BDS of diesel was investigated in an airlift bioreactor under optimized conditions. Sulfur reduction after 30 h was 14 mg/l.     

Effect of shear stress on anthraquinones production by Rubia tinctorum suspension cultures

Suspension cultures of Rubia tinctorum, an anthraquinones (AQs) producer, were grown both in Erlenmeyer flasks at 100 rpm and in a 1.5 L mechanically stirred tank bioreactor operating at 450 rpm. The effect of hydrodynamic stress on cell viability, biomass, and AQs production was evaluated. Cell viability showed a transient decrease in the bioreactor during the first days, returning to the initial values toward the end of the culture time. The biomass obtained in the bioreactor was 29% lower than that attained in the Erlenmeyer flasks. The H2O2 production in the bioreactor (with peaks at 7 and 10 days) was about 15 times higher than that obtained in the flasks. A clear relationship exists between the maximum concentration of H2O2 generated and AQs produced. The AQs content in the bioreactor was 233% higher than that in the Erlenmeyer flasks. The AQs specific productivity in the stirred tank and in the Erlenmeyer flasks was 70.7 and 28.5 micromol/g FW/day, respectively. This production capability was maintained in the regrowth assays. On the other hand, the negative effects of hydrodynamic stress on viability and biomass concentration observed in the bioreactor culture were reverted in the regrowth cultures. It can be concluded that R. tinctorum suspension cultures are able to grow in stirred tanks at 450 rpm responding to the hydrodynamic stress with higher concentrations of AQs, which suggest the possibility of a technological approach taking advantage of this phenomenon.     

Hydrodynamic studies in an airlift reactor with an enlarged degassing zone

The hydrodynamic behaviour of a 60?l three-phase airlift bioreactor, of the concentric draught tube type, with an enlarged degassing zone has been studied. Ca-alginate beads were used as the solid phase. Airflow rate (from 1.9 to 90.2?l/min), solids loading (0% to 40% (v/v)) and solids density (1016 and 1038?kg/m³) were manipulated and their influence on solids and gas holdup, circulation and mixing times and in the interstitial liquid velocity was determined. Riser and downcomer solids holdup was found to decrease with the increase of airflow rate and to increase with solids loading and density. On the contrary, gas holdup in the riser and in the downcomer increased with airflow rate and decreased with solids loading and density. By increasing airflow rate, a decrease in circulation time was observed while the effects of solids loading and density were negligible. Mixing time decreased with airflow rate, increased with solids density, in the studied range, and presented a maximum for solids loading of approximately 20% (v/v).     

Growth characteristics of Arthrospira platensis cultured inside a new close-coil photobioreactor incorporating a mandrel to control culture temperature

The aim of this study was to investigate Arthrospira growth inside a new CCP incorporating a mandrel for culture temperature control. Some hydrodynamic aspects and photobioreactor performances were investigated as well. The bioreactor incorporated A. platensis grown under batch and semicontinuous conditions. Two systems were used to recycle Arthrospira cultures: a peristaltic pump and an airlift system. When the pump recycled the culture, we achieved a very high Dean number (De=3,950), which decreased a great deal when the pump was replaced with the airlift system. During outdoor Arthrospira batch growth, a cell concentration of 16.4 g (DW)l-1 was reached after 9 days. However, the maximum chlorophyll content of the biomass (2.0% of DW) was achieved on the fifth and sixth days. The highest daily biomass output rate was obtained using the airlift system, when the CCP was operated under a semicontinuous regime: the gross output rate was 2.85+/-0.37 g (DW) l-1 d-1 and the net was 2.32+/-0.11 g (DW) l-1 d-1. The advantages of the airlift system may be due to the low concentration of oxygen built up inside Arthrospira culture and the lack of cell damage due to the pump system. Thus, oxygen and pump stress may have been avoided.     

alpha-Amylase production by Bacillus subtilis with dregs in an external-loop airlift bioreactor

An external-loop airlift bioreactor, with a low ratio 2.9 of height-to-diameter of the riser and a ratio 6.6 of riser-to-downcomer diameter, was used to produce alpha-amylase from fermentation with dregs by Bacillus subtilis. The effects of gas flow rate and liquid volume on alpha-amylase production were investigated. After a 36-h fermentation time, an average of 432.3U/ml alpha-amylase activity was obtained under the conditions of liquid volume 8.5l and gas flow rate 1.2vvm for the first 12h of fermentation, 1.4vvm from 12 to 27h, and 1.2vvm from 27h to the end. The activity was higher than that obtained in shaking flasks (409.0U/ml) and in a mechanically stirred tank bioreactor (397.2U/ml) under optimized operating conditions. The fermentation cycle of the airlift bioreactor was shorter than the 48h required for the shaking flasks and close to the 36h of the mechanically stirred tank bioreactor. It was demonstrated that the external-loop airlift bioreactor could substitute for the traditional mechanically stirred tank bioreactor to produce alpha-amylase from fermentation by Bacillus subtilis with dregs.     

Biotransformation of glucose to gluconic acid by Aspergillus niger—study of mass transfer in an airlift bioreactor

A glucose–gluconic acid biotransformation system was suggested for the experimental study of oxygen transfer in bioreactors. This biosystem was used for the investigation of the effect of the flow rate and biomass concentration on the volumetric oxygen transfer coefficient k_La in a 10 dm³ internal-loop airlift bioreactor. For this purpose, the fermentation broth of the mycelial strain Aspergillus niger was employed, representing a three-phase system, where bubbles come into contact with dense rigid pellets. The results showed that the presented biotransformation system can be successfully utilised for the determination of the oxygen transfer rate in airlift bioreactors. The experiments showed a strong positive influence of the air flow rate on the rate (r_Glu), specific rate of gluconic acid production (k_Glu/X) as well as on the volumetric oxygen transfer coefficient (k_La). This confirmed an expected limitation of production rate by the oxygen transport from the gas to the liquid phase in the whole range of air flow rates applied. Moreover, consistent curves of the production rate r_Glu and k_La values vs. biomass concentration c_X (amount of enzymes) were observed. These exhibited a local maximum for c_X equal to 6.68 g dm⁻³. On the other hand, the specific production rate monotonously decreased with increasing biomass concentration. A decline of k_La values at higher c_X values was attributed to a bubble coalescence promoting effect of mycelial pellets.     

Computational fluid dynamics modeling of mass transfer behavior in a bioreactor for hairy root culture. I. Model development and experimental validation

A two-dimensional axisymmetric computational fluid dynamics (CFD) model based on a porous media model and a discrete population balance model was established to investigate the hydrodynamics and mass transfer behavior in an airlift bioreactor for hairy root culture.During the hairy root culture of Echinacea purpurea, liquid and gas velocity, gas holdup, mass transfer rate, as well as oxygen concentration distribution in the airlift bioreactor were simulated by this CFD model. Simulative results indicated that liquid flow and turbulence played a dominant role in oxygen mass transfer in the growth domain of the hairy root culture. The dissolved oxygen concentration in the hairy root clump increased from the bottom to the top of the bioreactor cultured with the hairy roots, which was verified by the experimental detection of dissolved oxygen concentration in the hairy root clump. This methodology provided insight understanding on the complex system of hairy root culture and will help to eventually guide the bioreactor design and process intensification of large-scale hairy root culture.     

Biomass axial distribution in airlift bioreactor with yeast and plant cells

This study was aimed at determining the degree of biomass homogeneity in the various parts of an internal loop airlift bioreactor, thus verifying the assumption, often made in bioreactor studies, of a well-mixed liquid-biomass system. Following characterization of the hydrodynamics of the vessel with water, the axial biomass distribution in the riser and downcomer was determined for plant and yeast cell suspensions of 5.8, 8.5, and 12.5 g DW/L Phaseolus vulgaris and of 30 and 46 g DW/L Saccharomyces cerevisiae. The airlift bioreactor with a surface ratio A(D)/A(D) of 1.04 and aspect ratio of 4.95 was investigated under various aeration rates. The yeast cells were found to be distributed practically uniformly throughout the vessel at the aeration rates of 0.1-1.45 vvm. However, in the case of the denser and cluster-forming plant cells, a clear trend of a gradual bio-mass accumulation in the downcomer, a slightly lower but uniform biomass loading in the riser, and a slightly higher biomass concentration in the gas-liquid separator was observed at the lower aeration rates of 0.1-0.61 vvm. In the case of powderized calcium carbonate (55g/L) often used in fermentations of organic acids, a slight trend of a gradual accumulation of solids towards the bottom parts in both the downcomer and riser was observed. A better representative sampling location, in terms of solids and biomass loading, seems to be in the middle part of the vessel. It is suggested that airlift bioreactors with higher aspect ratios (>5) may be prone to a more significant inhomogeneity of solids (biomass and particles).     

Effects of rheological properties and mass transfer on plant cell bioreactor performance: production of tropane alkaloids

Volumetric mass transfer coefficients, K(L)a were measured over an aeration rate range from 0.1 to 1.0 vvm in a 1.2-L draft-tube-type airlift bioreactor for different Datura stramonium cell concentrations and correlated with superficial air velocity and rheological properties of the cell suspension. The measured K(L)a values (17-40 h(-1)) for a cell volume fraction of 0.2 (v/v) were approximately 2 times higher than those for the highest cell concentrations tested (cell volume fraction 0.7-0.8 v/v). Cell suspensions exhibited yield stress and pseudoplastic behavior. This behavior was described by the Casson model. The estimated yield stress values depended upon cell concentration with an exponent of 4.0. An empirical correlation based on the data for plant cell suspensions exhibiting yield stress was developed in order to determine aeration strategy for the plant cell cultivation in draft-tube-type airlift bioreactors: \documentclass{article}\pagestyle{empty}\begin{document}$$ {\rm K}_{\rm L} {\rm a} = {\rm A}({\rm U}_{{\rm gr}});{0.3} ({\rm \eta }_{{\rm eff}});{ - 0.4} $$\end{document} Aeration rates above 1.0 vvm caused a significant drop in cell yield and product content. Maximum growth and production were obtained at 0.6 vvm aeration. The cell and product yields obtained at 1.7 vvm were 2.8 times lower than the maximum values (25 g cell DW/L and 73.8 mg tropane alkaloid/L). The effects of the increased aeration rates on cell yield were also evaluated in terms of Reynolds stress. It was found that there was a relation between cell damage and the estimated Reynolds stress. The Reynolds stress estimated for the same aeration rate decreased with increasing cell concentration, suggesting that cells in the cultures at low cell concentrations are subjected to hydrodynamic damage. In the experiments with the cell cultures having a cell concentration of 0.3 (v/v), approximately 70% reduction in cell concentration was observed when the Reynolds stress was increased from 10 to 50 dyn/cm(2). (c) 1993 John Wiley & Sons, Inc.     

Hydrodynamic performance of a three-phase airlift bioreactor with an enlarged degassing zone

The hydrodynamics of biotechnological processes is complex. So far, few studies were made with bioreactors of the airlift type with an enlarged degassing zone.In this work, the influence of solids loading, solids specific gravity and draught tube dimensions on mixing and circulation times and critical air flow rate for an internal loop airlift bioreactor with an enlarged sedimentation/degassing zone is studied.The results indicate that the critical air flow rate as well as the mixing time increase with an increase in solids loading in the bioreactor. Circulation time presents a maximum for a solids load between 5 and 10% (v/v). It is also shown that small variations in solids specific gravity, for values close to that of the liquid, have a significant influence on the critical air flow rate and on the mixing time.An optimal (minimal) value for the circulation time and for the critical air flow rate was obtained for a riser to down comer diameter ratio of 0.46. The minimum mixing time was obtained for a riser to down comer height ratio of 0.80.This work was supported by J.N.I.C.T. (Junta Nacional de Investigação Cientifica e Tecnológica).     

Coenzyme Q<Subscript>10</Subscript> production by <Emphasis Type="Italic">Rhodobacter sphaeroides</Emphasis> in stirred tank and in airlift bioreactor

A higher Coenzyme Q₁₀ (CoQ₁₀) concentration of 25.04 mg/l was found in airlift bioreactor than the value of 18.11 mg/l obtained in stirred tank under the aerobic-dark cultivation of Rhodobacter sphaeroides. Aeration rate didn’t show obvious impact to CoQ₁₀ production in airlift bioreactor. The fed-batch operation in airlift bioreactor could increase the biomass concentration and led to the maximum CoQ₁₀ concentration of 33.91 mg/l measured, but a lower CoQ₁₀ cell content (3.5 mg CoQ₁₀/DCW) was observed in the fed-batch operation as compared to the batch operation. To enhance the CoQ₁₀ content, an aeration-change strategy was proposed in the fed-batch operation of airlift bioreactor. This strategy led to the maximum CoQ₁₀ concentration of 45.65 mg/l, a 35% increase as compared to the simple fed-batch operation. The results of this study suggested that a fed-batch operation in airlift bioreactor accompanying aeration-change could be suitable for CoQ₁₀ production.     

Production of extracellular protease from crude substrates with dregs in an external-loop airlift bioreactor with lower ratio of height to diameter

Bacillus subtilis AS1.398 was cultivated in a 11.5-L total volume external-loop airlift bioreactor with a low height-to-diameter ratio of 2.9 and a riser-to-downcomer diameter ratio of 6.6 for the production of protease from crude substrates with dregs. The influence of aeration rate, liquid volume, and sparger hole diameter on protease production was investigated. An average of 8197 u/mL protease activity was obtained after a total fermentation time of 32 h in the external-loop airlift bioreactor with a liquid volume of 8.5 L, air flow rate of 1.5 vvm, and sparger hole diameter of 1.5 mm. The addition of one stainless steel sieve plate in the riser of the airlift bioreactor increased productivity of protease. After 32 h of fermentation, an average of 8718 u/mL protease activity was achieved in the external-loop airlift bioreactor with one sieve plate and an air flow rate of 1.2 vvm, liquid volume of 8.5 L, and gas sparger hole diameter of 1.5 mm. This was 9.0% higher than the typical averages of about 8000 u/mL protease activity in the mechanically stirred tank bioreactors of the enzyme factory using the same microorganism. It is possible to make a scale-up of the external-loop airlift bioreactor and feasible to operate it for production of protease from crude substrate with dregs.     

Small-scale liquid mixing in a bioreactor column with xanthan-gum simulated filamentous media

Using the heat pulse technique, the local mean flow liquid velocity and the mixing conditions for twophase flow in the riser of an airlift bioreactor have been measured and analysed. Xanthan-gum solutions were used as the physical model to some filamentous broths reported in the literature. A two-fold decrease of liquid velocity and diffusional mixing regime are predicted for the course of a fermentation process proceeding in a non-Newtonian biomass growth circulation system.     

An airlift biofilm reactor for the biodegradation of phenol by Pseudomonas stutzeri OX1

Phenol bioconversion by Pseudomonas stutzeri OX1 using either free or immobilized cells was investigated with the aim of searching for optimal operating conditions of a continuous bioconversion process. The study was developed by analyzing: (a) free-cell growth and products of phenol bioconversion by batch cultures of P. stutzeri; (b) growth of P. stutzeri cells immobilized on carrier particles; (c) bioconversion of phenol-bearing liquid streams and the establishment and growth of an active bacterial biofilm during continuous operation of an internal-loop airlift bioreactor. We have confirmed that free Pseudomonas cultures are able to transform phenol through the classical meta pathway for the degradation of aromatic molecules. Data indicate that bacterial growth is substrate-inhibited, with a limiting phenol concentration of about 600 mg/L. Immobilization tests revealed that a stable bacterial biofilm can be formed on various types of solid carriers (silica sand, tuff, and activated carbon), but not on alumina. Entrapment in alginate beads also proved to be effective for P. stutzeri immobilization. Continuous bioconversion of phenol-bearing liquid streams was successfully obtained in a biofilm reactor operated in the internal-circulation airlift mode. Phenol conversion exceeded 95%. Biofilm formation and growth during continuous operation of the airlift bioreactor were quantitatively and qualitatively assessed.     

A fiber-bed bioreactor for anchorage-dependent animal cell cultures: part II. Scaleup potential

A simple hydrodynamic model is introduced to describe the airlift fiber-bed bioreactor, which can enhance the volumetric productivity of anchorage-dependent animal cell cultures. By applying the model, liquid flow rates and volumetric mass transfer coefficients are predicted and are in agreement with experimental measurements. Consequently, the optimal reactor configuration giving the maximal oxygen supply is derived. Also, theoretical scaleup potential of this concentric internal loop reactor is considered for volumes ranging from 10 to 67,000 L with which cell densities of 5.1 x 10(7) and 1.2 x 10(7) cells/cm(3), respectively, can be maintained.     

A multikinetic model approach to predict gluconic acid production in an airlift bioreactor

This paper uses a multikinetic approach to predict gluconic acid (GA) production performance in a 4.5 L airlift bioreactor (ALBR). The mathematical model consists of a set of simultaneous firstorder ordinary differential equations obtained from material balances of cell biomass, GA, glucose, and dissolved oxygen. Multikinetic models, namely, logistic and contois equations constitute kinetic part of the main model. The main model also takes into account the hydrodynamic and mass transfer parameters. These equations were solved using ODE solver of MATLAB v6.5 software. The mathematical model was validated with the experimental data available in the literature and is used to predict the effect of change in initial biomass and air sparging rate on the GA production. It is concluded that the mathematical model incorporated with multikinetic approach would be more efficient to predict the change in operating parameters on overall bioprocess of GA production in an ALBR.     

气升式生物反应器在杂交瘤细胞培养中的应用

前述研究工作基础上,设计开发了10L规模的动物细胞培养用气升式生物反应器。应用该生物反应器悬浮培养杂交瘤细胞．通过平行试验,考察了该反应器设计的合理性和可靠性。结果显示该反应器不存在限制细胞生长、代谢和产物生成的因素,而且细胞破损技彻底消除,表明该气升式生物反应器给细胞生长、代谢和产物生成提供了理想的培养环境,其设计是成功的。     

Production of eleutherosides in in vitro regenerated embryos and plantlets of <Emphasis Type="BoldItalic">Eleutherococcus chiisanensis</Emphasis>

High frequency somatic embryogenesis of Eleutheorcoccus chiisanensis was achieved through suspension culture of embryogenic cells in hormone-free Murashige and Skoog liquid medium supplemented with 30 g sucrose l⁻¹. Cotyledonary somatic embryos were germinated and converted into plantlets using 20 μM gibberellic acid which were then grown in a 10 l airlift bioreactor. HPLC analysis revealed the accumulation of eleutheroside B, E and E1 in the embryos and plantlets. Thus mass production of embryos and plantlets of E. chiisanensis can be achieved in liquid cultures and the biomass produced may become an alternative source of eleutherosides.